Search NASA⌕ Search

SEARCH · Search NASA

Results for “trisonic wind tunnels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

A Transonic and Surpersonic Investigation of Jet Exhaust Plume Effects on the Afterbody and Base Pressures of a Body of Revolution

An experimental aerodynamic investigation was conducted to provide data for studies to determine the criteria for simulating rocket engine plume induced aerodynamic effects in the wind tunnel using a simulated gaseous plume. Model surface and base pressure data were obtained in the presence of both a simulated and a prototype gaseous plume for a matrix of plume properties to enable investigators to determine the parameters that correlate the simulated and prototype plume-induced data. The test program was conducted in the Marshall Space Flight Center's 14 x 14-inch trisonic wind tunnel using two models, the first being a strut mounted cone-ogive-cylinder model with a fineness ratio of 9. Model exterior pressures, model plenum chamber and nozzle performance data were obtained at Mach numbers of 0.9, 1.2, 1.46, and 3.48. The exhaust plume was generated by using air as the simulant gas, or Freon-14 (CF4) as the prototype gas, over a chamber pressure range from 0 to 2,000 psia and a total temperature range from 50 to 600 F.

Andrews, C. D.↗
NASA NTRS2015

Reducing the Effect of Transducer Mount Induced Noise on Aeroacoustic Wind Tunnel Testing Data with a New Transducer Mount Design

Characterization of launch vehicle unsteady aerodynamics is a field best studied through experimentation, which is often carried out in the form of large scale wind tunnel testing. Measurement of the fluctuating pressures induced by the boundary layer noise is customarily made with miniature pressure transducers installed into a model of the vehicle of interest. Literature shows that noise level increases between two to five decibels (dB referenced to 20 micropascal) can be induced when the transducer surface is not mounted perfectly flush with the model outer surface. To reduce this artificially induced noise, special transducer holders have been used for aeroacoustic wind tunnel testing by NASA. This holder is a sleeve into which the transducer fits, with a cap that allows it to be mounted in a recessed hole in the model. A single hole in the holder allows the transport of the tunnel medium so the transducer can discriminate the fluctuating pressure due to the turbulent boundary layer noise. The holder is first dry fitted into the model and any difference in height between the holder and the model surface can be sanded flush. The holder is then removed from the model, the transducer glued inside the holder, and the holder replaced in the model, secured also with glue, thus eliminating the problem of noise level increases due to lack of flushness. In order to work with this holder design, special transducers have been ordered with their standard screen removed and the diaphragm moved as close to the top of the casing as possible to minimize any cavity volume. Although this greatly reduces induced noise due to the transducers being out of flush, the holders can also induce a cavity resonance that is usually at a very high frequency. This noise is termed transducer mount induced noise (XMIN). The peak of the mode can vary with the cavity depth, boundary layer noise that can excite the mode, tunnel flow medium, and the build of the transducers. Because the boundary layer flow interaction with the microphone holder seems to have some effect on the cavity resonance response, the NASA/Marshall Space Flight Center (MSFC) aeroacoustic team postulated that changing the design of the holder might reduce the cavity resonance response. An experiment was performed at the MSFC Trisonic Wind Tunnel comparing a new holder design with the traditional MSFC holder. The new holder design is intended to mimic the Kulite Semiconductors, Inc. B-screen, where the single hole of the traditional MSFC holder is replaced by a series of ten 0.007 inch diameter holes. This particular design serves to protect the transducer diaphragm as in the manufacturer's B-screen, but also increases the frequency of the XMIN such that it is not apparent in the data collected from aeroacoustic wind tunnel tests. MSFC compared the two holder designs by installing two transducers in standard holders on one side of a ten inch long ten degree cone, and two transducers in B-screen holders on the opposite side for a series of runs at different conditions. Over 11-13 February, 2013, the model was run at Mach numbers between 0.80 and 1.96 at angles of attack at 0 deg, plus or minus 1 deg, plus or minus 2 deg, plus or minus 4 deg, and plus or minus 8 deg. Model roll attitudes at 0 deg, 90 deg, and 180 deg were tested to isolate potential tunnel bias. This paper presents results from the test showing that the proposed holder design significantly reduces the influence of XMIN on measured fluctuating pressure levels.

Herron, A. J.↗
NASA NTRS2015

Reducing the Effect of Transducer Mount Induced Noise on Aeroacoustic Wind Tunnel Testing Data with a New Transducer Mount Design

Flight vehicle aeroacoustic environments induced during transonic and supersonic flight are usually predicted by subscale wind tunnel testing utilizing high frequency miniature pressure transducers. In order to minimize noise induced by the measurement itself, transducer flush mounting with the model surface is very important. The National Aeronautics and Space Administration (NASA) has accomplished flushness in recent testing campaigns via use of a transducer holder that can be machined and sanded. A single hole in the holder allows the flow medium to interact with the transducer diaphragm. Noise is induced by the resulting cavity however, and is a challenge to remove in post-processing. A new holder design has been developed that minimizes the effects of this transducer mount induced noise (XMIN) by reducing the resonance amplitude or increasing its resonance frequency beyond the range of interest. This paper describes a test conducted at the NASA/George C. Marshall Space Flight Center Trisonic Wind Tunnel intended to verify the effectiveness of this design. The results from this test show that this new transducer holder design does significantly reduce the influence of XMIN on measured fluctuating pressure levels without degrading a transducer's ability to accurately measure the noise external to the model.

Herron, Andrew J.↗
DOE OSTI2025

LES of a Mach 2 Expansion Compression Flow

Presentation covers recent LES simulations of which have similar flow conditions to recent TriSonic Wind Tunnel experiments.

Nicholson, Gary Lloyd [Sandia National Laboratorie↗
NASA NTRS1971

Space shuttle: Static stability and control investigation of the NR-GD/C delta wing booster (B-15B-1) and a Reusable Nuclear Stage (RNS) M = 0.6 - 4.96

Experimental aerodynamic investigations were made in the NASA/MSFC 14 x 14 inch trisonic wind tunnel on a NR-GD/C 0.0031 scale model delta wing booster (B-15B-1) and reusable nuclear stage (RNS). Three basic configurations were tested: (1) the B-15B-1 booster alone, (2) the RNS alone, and (3) the booster with the RNS mounted piggyback. Six component force and moment data were recorded for each of these configurations over an angle of attack range from -16 deg to 4 deg at zero degrees sideslip, and over an angle of sideslip range from -10 deg to 10 deg at zero and -6 degrees angle of attack. The configurations were tested over a Mach number range of 0.6 to 5.0 with a nominal Reynolds number of 6.5 million per foot except for Mach 1.2 and 3.0 where the Reynolds number were 12.4 million and 4.4 million per foot respectively.

Allen, E. C.↗
NASA NTRS1971

Space shuttle: Effect of configuration changes on the directional characteristics of a GD/C booster Mach no. 1.2 - 4.96

Force tests on a 0.0035-scale model of the General Dynamics/Convair aerospace space shuttle B-15B-1 booster were conducted in the MSFC trisonic wind tunnel. The configuration has a low delta wing, all-movable delta-planform canard controls, and a single vertical tail. The test was devoted to investigating the effects of various configuration variables upon lateral-directional characteristics. These variables included wing dihedral, rudder flare, and body flap deflection. Yaw runs were made at angles of attack of 6, 10, 15, 25, 30, and 35 degrees. The Mach number range for this test was 1.20 to 4.96.

Brickey, J.↗
NASA NTRS1971

Aerodynamic characteristics of the Grumman H-33 orbiter mated to a three segment solid propellant booster

Experimental aerodynamic investigations were conducted on a .003366-scale model of the Grumman space shuttle configuration mounted to a three (3) segmented solid propellant booster. These tests were conducted in the MSFC 14-inch trisonic wind tunnel over a Mach number range of 0.6 to 4.96. The purpose of the test was to determine the aerodynamic characteristics of this configuration. Aerodynamic data was taken over a nominal angle of attack and angle of sideslip of -10 degrees to 10 degrees at zero degrees beta and alpha respectively. In addition, data was obtained for the H-33 orbiter alone to supplement data from TWT 502 and TWT 503.

Sims, F.↗
NASA NTRS1971

Aerodynamic characteristics of the MSFC pressure fed boosters at high angles of attack (M equals 0.6 to 5.0)

Experimental aerodynamic investigations were conducted in the 14 x 14 inch trisonic wind tunnel during early December 1971 on 0.003366 scale models of the space shuttle pressure fed booster configurations. The basic configurations tested were a 40 deg cone/cylinder/13 deg flare designated the pressure fed booster and a 35 deg cone/cylinder designated the pressure fed booster configuration x. Six component aerodynamic force and moment data were recorded over a Mach number range from 0.6 to 5.0 at angles of attack from +20 to +60 deg at 0 deg sideslip and over a sideslip range from -10 to +10 deg at 31 and 52 deg angles of attack. Primary configuration variables for the two basic pressure fed booster configurations were fin size and fin dihedral position.

Baker, J.↗
NASA NTRS1971

Determination of longitudinal and lateral directional aerodynamic characteristics of the B19B pressure-fed booster and the B19B booster/040A orbiter launch configuration

The 0.003366 scale models of the space shuttle pressure-fed booster and booster/orbiter configurations were tested in the MSFC 14-inch trisonic wind tunnel. The test was conducted as a static stability and control investigation over a Mach range of 0.60 to 5.00. The booster alone configuration was tested with various tail sizes, tail wedge angles, tail flaps, spoilers, and a body flare drag skirt. Two launch configurations were tested; one being the MSC orbiter location on the booster tank and the other being the North American Rockwell orbiter location. Orbiter buildup, longitudinal position, incidence angle, and booster tail on and off were the variables for launch configuration. Booster alone models were pitched over an angle of attack range of -4 to +14 and +20 to +60 deg at zero deg yaw angle and yawed over an angle of sideslip range of -10 to +10 deg at 52 deg angle of attack. Launch configuration models were yawed -10 to +10 deg at zero degrees angle of attack and yawed -10 to +10 deg at zero and -6 deg angle of attack. All models were rolled 45 deg during selected runs.

Mcginnis, R. F.↗
NASA NTRS1972

Aerodynamic characteristics of the North American Rockwell space shuttle delta-wing orbiter (110C) alone and with belly-mounted external oxygen/hydrogen tanks (M equals 0.6 to 5.0)

Experimental aerodynamic investigations were conducted at the MSFC 14 x 14 inch trisonic wind tunnel on a .0044 scale model of the space shuttle orbiter, 110C. The test configurations included the orbiter alone and with external oxygen/hydrogen belly tanks. The six component aerodynamic force and moment data obtained cover a Mach number range from 0.6 to 4.96 at angles of attack from 10 to 60 deg at 0 deg sideslip angle and -10 to 10 deg at -6 deg sideslip angle. Reynolds number per unit length varied somewhat with Mach number but was a nominal 6.8 million per foot.

Allen, E. C.↗
NASA NTRS1972

Aerodynamic characteristics of several launch configurations utilizing the Titan 3 L booster and MMC DTO-7 Orbiter

The .00429 scale model Titan 3 booster was mated with the DTO-7 space shuttle orbiter with drop tanks and tested for aerodynamic performance in a 14 x 14 inch trisonic wind tunnel. Six component aerodynamic force and moment data were measured on several variations of the above component in a launch configuration over a Mach number range from 0.6 to 3.48. Angle of attack ranged from -12 deg to 12 deg at 0 deg and -6 deg sideslip angle and sideslip angle ranged from -12 deg to 12 deg at 0 deg angle of attack. Date are presented in plotted form in both the stability and body axis system.

Michna, D. J.↗
NASA NTRS1972

Space shuttle: Aerodynamic characteristics of the Titan T 3 (1207-4)/GAC H-33 launch configuration

Aerodynamic data obtained in a 14-inch trisonic wind tunnel test on static stability and drag of 0.003366-scale models of the Grumman H-33 drop tank orbiter and the Titan T 3 (1207-4) expendable booster are presented. The orbiter was mounted to the booster both piggyback and tandem. Data were obtained over a Mach number range of 0.6 to 5.0. Angle of attack data were obtained from -16 deg to +4 deg at both 0 deg and -6 deg sideslip for the piggyback configuration, but were limited to -10 deg to +10 deg at 0 deg sideslip for the tandem configuration. Primary configuration variations, other than piggyback and tandem mount, were the number and location of solid propellant strap-on boosters.

Sims, J. F.↗
NASA NTRS1972

Space shuttle: Static aerodynamic characteristics of the MSC-040A the Msc-040A space shuttle orbiter with wedge centerline vertical and twin vertical tails at Mach numbers from 0.6 to 4.96

The results are presented from experimental aerodynamic investigations conducted on a 0.6-percent scale model of the MSC-040 space shuttle orbiter in a 14 inch trisonic wind tunnel. The purpose of the test program was to define the stability, control, and performance characteristics of the baseline MSC-040A orbiter configuration with proposed alternate wing pods, with several vertical tail configurations with and without flared rudders, and with upper wing surface flap deflections. Force and moment data and model base and balance cavity pressure data were obtained for a Mach range of 0.60 through 4.96 and dynamic pressure range of 465 through 1580 psf. Model attitude was varied from 0 to +34 degrees angle of attack at zero sideslip and -4 to +10 degrees angle of sideslip at 0, 10, 20, and 24 degrees angle of attack.

Glass, K. J.↗
NASA NTRS1972

Space shuttle: Aerodynamic characteristics of 0.003367 scale models of the MMC retro-glide booster alone and mated with the MSC 040-A orbiter

Plotted data results are presented of aerodynamic tests conducted on the 0.003367 scale models of the retro-glide booster alone and mated with the 040A orbiter. The test was conducted in the NASA/MSFC 14 Inch Trisonic Wind Tunnel over a Mach number range of 0.6 to 4.95 with angles of attack varying from -10 deg to 60 deg. The test was to obtain six degree of freedom force and moment data on the launch configuration and booster reentry configuration for preliminary stability and control analysis.

Michna, D. J.↗