Search NASA⌕ Search

SEARCH · Search NASA

Results for “visual analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Verification of a two-dimensional infiltration model for the resin transfer molding process

A two-dimensional finite element model for the infiltration of a dry textile preform by an injected resin was verified. The model, which is based on the finite element/control volume technique, determines the total infiltration time and the pressure increase at the mold inlet associated with the RTM process. Important input data for the model are the compaction and permeability behavior of the preform along with the kinetic and rheological behavior of the resin. The compaction behavior for several textile preforms was determined by experimental methods. A power law regression model was used to relate fiber volume fraction to the applied compaction pressure. Results showed a large increase in fiber volume fraction with the initial application of pressure. However, as the maximum fiber volume fraction was approached, the amount of compaction pressure required to decrease the porosity of the preform rapidly increased. Similarly, a power law regression model was used to relate permeability to the fiber volume fraction of the preform. Two methods were used to measure the permeability of the textile preform. The first, known as the steady state method, measures the permeability of a saturated preform under constant flow rate conditions. The second, denoted the advancing front method, determines the permeability of a dry preform to an infiltrating fluid. Water, corn oil, and an epoxy resin, Epon 815, were used to determine the effect of fluid type and viscosity on the steady state permeability behavior of the preform. Permeability values measured with the different fluids showed that fluid viscosity had no influence on the permeability behavior of 162 E-glass and TTI IM7/8HS preforms. Permeabilities measured from steady state and advancing front experiments for the warp direction of 162 E-glass fabric were similar. This behavior was noticed for tests conducted with corn oil and Epon 815. Comparable behavior was observed for the warp direction of the TTI IM7/8HS preform and corn oil. Mold filling and flow visualization experiments were performed to verify the analytical computer model. Frequency dependent electromagnetic sensors were used to monitor the resin flow front as a function of time. For the flow visualization tests, a video camera and high resolution tape recorder were used to record the experimental flow fronts. Comparisons between experimental and model predicted flow fronts agreed well for all tests. For the mold filling tests conducted at constant flow rate injection, the model was able to accurately predict the pressure increase at the mold inlet during the infiltration process. A kinetics model developed to predict the degree of cure as a function of time for the injected resin accurately calculated the increase in the degree of cure during the subsequent cure cycle.

Hammond, Vincent H.↗
NASA NTRSDate not supplied

Mining the Gravity Mutants of Arabidopsis

Gravity mutants are a valuable resource for understanding gravity perception, signaling, and response in plants. A review of 190 publications resulted in a list of 97 loci with mutations that caused a gravitropic phenotype. While all these mutants show some form of gravity phenotype, several are also generally defective in growth. After removing these nonspecific mutants, 76 loci were deemed to have true gravity mutants. The gene list was then used to create a sortable database containing key factors of gravity signaling as well as data on methodologies and the development of mutant lines. Indexing this database has allowed us to pull out trends that were not visible in individual publications. For example, mutants that are unable to rearrange starch statoliths make up a larger proportion of the described inflorescence stems mutants than any other organ. Comparing these statolith mutants across organs shows that root and inflorescence stems consistently display different phenotypes for the same class of defect. The more severe gravity defects are most commonly described in root tissue while other tissues are more likely to show only a delayed or reduced response to gravity. The experience of members of the GeneLab plant Analytics Working Group (AWG) in data visualization and gene mapping have sparked new ideas for utilizing this database. Knowledge of shared traits, mutant development, and growth can provide a new resource for the production of seed lines specialized for their response to gravity.

gravitropism↗
NASA NTRSDate not supplied

Celestial Mapping System for Lunar Surface Mapping and Analytics

Celestial Mapping System (CMS) is a software platform to generate virtual 3D globe for celestial bodies within our solar system. Various layers are built on top of the virtual globe to provide visualization of high resolution imagery, enable precise measurements, build analytical capabilities and broad range of functionalities to assist planetary scientists and mission planners. CMS is built using OpenJDK 11 and will run on a wide variety of platforms such as Linux, Windows, OSX, etc. It has a thick client with less overhead to access hardware resources. This allows features such as terrain profiling and distance calculations to be performed on the client and on the fly. The present focus of CMS is on developing lunar mapping tool kits to provide features such as - 3D first person view with zoom and navigational capabilities, realistic terrain visualization based on LRO data, measurement tools, Apollo landing site annotations, stereoscopic view, elevation profiles, line of sight analysis and many more. The application is developed to provide situational and domain awareness on Lunar surface, planning capabilities for equipment placements and traverse path optimization. As data becomes available, CMS has the capabilities to integrate data sets that change dynamically in real-time, which will be useful for monitoring satellites and remotely-sensed data on Lunar surface. CMS utilizes NASA WorldWind Java library and OpenGL to achieve high-performance rendering of data and measurements, and also adheres to OGC standards. CMS supports importing synthetic features in a variety of 3D, 2D, vector and raster formats. Nomenclature is pulled from USGS Moon IAU2000 database, and lunar parameters are based of the standardized IAU2000 Moon ellipsoid. GDAL (Geospatial Data Abstraction Library) was used to modify and test the accuracy of datasets before integrating into the application. Our high-resolution global elevation model was compared with the LRO LOLA DEM elevation values and tested to ensure accuracy. Celestial Mapping System has several potential use cases for NASA including subsurface lava tubes visualization and analysis, soil analysis, resource visualization and representation on 3D globe.

GIS system↗
NASA NTRS1986

Non-linear effects in finite amplitude wave propagation through ducts and nozzles

In this paper an extensive study of non-linear effects in finite amplitude wave propagation through ducts and nozzles is summarized. Some results from earlier studies are included to illustrate the non-linear effects on the transmission characteristics of duct and nozzle terminations. Investigaiations, both experimental and analytical, were carried out to determine the magnitudes of the effects for high intensity pulse propagation. The results derived from these investigations are presented in this paper. They include the effect of the sound intensity on the acoustic characteristics of duct and nozzle terminations, the extent of the non-linearities in the propagation of high intensity impulsive sound inside the duct and out into free field, the acoustic energy dissipation mechanism at a termination as shown by flow visualizations, and quantitative evaluations by experimental and analytical means of the influence of the intensity of a sound pulse on the dissipation of its acoustic power.

Salikuddin, M.↗
NASA NTRS2016

Space Launch System Vibration Analysis Support

The ultimate goal for my efforts during this internship was to help prepare for the Space Launch System (SLS) integrated modal test (IMT) with Rodney Rocha. In 2018, the Structural Engineering Loads and Dynamics Team will have 10 days to perform the IMT on the SLS Integrated Launch Vehicle. After that 10 day period, we will have about two months to analyze the test data and determine whether the integrated vehicle modes/frequencies are adequate for launching the vehicle. Because of the time constraints, NASA must have newly developed post-test analysis methods proven well and with technical confidence before testing. NASA civil servants along with help from rotational interns are working with novel techniques developed and applied external to Johnson Space Center (JSC) to uncover issues in applying this technique to much larger scales than ever before. We intend to use modal decoupling methods to separate the entangled vibrations coming from the SLS and its support structure during the IMT. This new approach is still under development. The primary goal of my internship was to learn the basics of structural dynamics and physical vibrations. I was able to accomplish this by working on two experimental test set ups, the Simple Beam and TAURUS-T, and by doing some light analytical and post-processing work. Within the Simple Beam project, my role involves changing the data acquisition system, reconfiguration of the test set up, transducer calibration, data collection, data file recovery, and post-processing analysis. Within the TAURUS-T project, my duties included cataloging and removing the 30+ triaxial accelerometers, coordinating the removal of the structure from the current rolling cart to a sturdy billet for further testing, preparing the accelerometers for remounting, accurately calibrating, mounting, and mapping of all accelerometer channels, and some testing. Hammer and shaker tests will be performed to easily visualize mode shapes at low frequencies. Short analytical projects using MATLAB were also assigned to aid in research efforts. These included integration of acceleration data for comparison to measured displacement data. Laplace and Fourier transforms were also investigated to determine viability as a method of modal decoupling. In addition to these projects, I was also able contribute work that would benefit future interns and the division as a whole. I gave a short presentation and answered questions to aid in the recruitment of subsequent interns and co-ops for the division. I also assisted in revisions and additions to Intern/Co-Op Handbook to provide incoming employees with background information on the organization they are about to work for. I further developed tutorial on Pulse software, which was used for data acquisition for both experiments and will be helpful to interns and engineers that may be unfamiliar to the software. I gained a diverse range of experience throughout my internship. I was introduced to advanced dynamics and analytical techniques. This was through new experience with both hands on experimentation and analytical post processing methods. I was exposed to the benefits of interdepartmental collaboration and developed stronger skills in time management by coordinating two different tests at once. This internship provided an excellent opportunity to see how engineering theories applied to real life scenarios, and an introduction to how NASA/JSC solves technical problems.

Johnson, Katie↗
NASA NTRS2006

The Synergistic Engineering Environment

The Synergistic Engineering Environment (SEE) is a system of software dedicated to aiding the understanding of space mission operations. The SEE can integrate disparate sets of data with analytical capabilities, geometric models of spacecraft, and a visualization environment, all contributing to the creation of an interactive simulation of spacecraft. Initially designed to satisfy needs pertaining to the International Space Station, the SEE has been broadened in scope to include spacecraft ranging from those in low orbit around the Earth to those on deep-space missions. The SEE includes analytical capabilities in rigid-body dynamics, kinematics, orbital mechanics, and payload operations. These capabilities enable a user to perform real-time interactive engineering analyses focusing on diverse aspects of operations, including flight attitudes and maneuvers, docking of visiting spacecraft, robotic operations, impingement of spacecraft-engine exhaust plumes, obscuration of instrumentation fields of view, communications, and alternative assembly configurations. .

Cruz, Jonathan↗
NASA NTRS2010

Risk Assessment Using the Three Dimensions of Probability (Likelihood), Severity, and Level of Control

Traditional hazard analysis techniques utilize a two-dimensional representation of the results determined by relative likelihood and severity of the residual risk. These matrices present a quick-look at the Likelihood (Y-axis) and Severity (X-axis) of the probable outcome of a hazardous event. A three-dimensional method, described herein, utilizes the traditional X and Y axes, while adding a new, third dimension, shown as the Z-axis, and referred to as the Level of Control. The elements of the Z-axis are modifications of the Hazard Elimination and Control steps (also known as the Hazard Reduction Precedence Sequence). These steps are: 1. Eliminate risk through design. 2. Substitute less risky materials for more hazardous materials. 3. Install safety devices. 4. Install caution and warning devices. 5. Develop administrative controls (to include special procedures and training.) 6. Provide protective clothing and equipment. When added to the twodimensional models, the level of control adds a visual representation of the risk associated with the hazardous condition, creating a tall-pole for the least-well-controlled failure while establishing the relative likelihood and severity of all causes and effects for an identified hazard. Computer modeling of the analytical results, using spreadsheets and threedimensional charting gives a visual confirmation of the relationship between causes and their controls

Watson, Clifford↗
NASA NTRS1975

An investigation of airflow over the aft portions of a variable sweep fighter configuration

An investigation of air flow over the aft portions of a variable sweep fighter aircraft configuration was made. Tests conducted in the unitary plan wind tunnel at Mach number 2.16 included measurements of forces, moments, and local static pressures as well as visual recordings of the air flow. An aerodynamic analytical prediction method was evaluated when used in data comparison at angles of attack of 0, 5, and 15 degrees. The results indicate that in supersonic flow the typical outboard located twin vertical tail arrangement tends to provide a more positive increment in normal-force on the afterbody fuselage and the horizontal tail than a single center-mounted vertical tail of similar planform shape. In addition, the results indicate that a method for aerodynamic analysis of wing-body-tail configurations currently available can provide reasonable estimates of pressure coefficient distributions on configurations in regions of complex supersonic flow. At this time, however, the available analytical method cannot adequately replace experimental wind tunnel tests for determining the supersonic flow environment of a given configuration.

Graves, E. B.↗
NASA NTRSDate not supplied

Celestial Mapping System and Digital Lunar Library Initiative

We are preparing to create an interactive, global 3D lunar environment with integrated dataset and AI/ML tools to provide unique value to mission planners, scientists and the entire lunar community. This lunar environment will be based on NASA Ames Celestial Mapping System (CMS) [1] and Digital Lunar Library (DLL) Initiative. CMS provides a 3D virtual Lunar Globe with extensive user friendly tool sets, that include high resolution terrain visualization, elevation profiles, measurement kits, slope analysis, path optimization, line of sight analysis, equipment planning and placement tools and many other functionalities [1]. It has a thick client with less overhead to access hardware resources. This allows features such as terrain profiling and distance calculations to be performed on the client and on the fly. The application is developed to provide situational and domain awareness on the Lunar surface, planning capabilities for equipment placements and traverse path optimization. As data becomes available, CMS has the capabilities to integrate data sets that change dynamically in real-time, which will be useful for monitoring satellites and remotely-sensed data on the Lunar surface. CMS supports importing synthetic features in a variety of 3D, 2D, vector and raster formats. In the future, these capabilities will be enhanced by incorporating AI/ML tools and a plug-in architecture to enable customization by the user groups. With the help of DLL we will be able to : 1) Amplify the value of lunar information with AI-powered data enhancements 2) Acquire and integrate lunar data with AI-assisted georectification and homogenization 3) Analyze lunar data with advanced 3D visualization, intelligent search-by-example 4) Apply lunar data insights to specific use cases with an open plug-in architecture. The CMS-DLL initiative will have several potential use cases for NASA and the lunar community in general, including subsurface lava tube visualization and analysis, soil analysis, in-situ lunar resource visualization and representation on 3D globe, and data analytics for utilization. REFERENCES: [1] https://celestial.arc.nasa.gov/

3D Globe↗
NASA NTRS2023

Exploring Interactive Visuals for Orbital Debris Report

NASA often produces reports or memos that include complex data and these findings can often be most effectively communicated using dynamic or interactive visualizations. While newsrooms, such as the New York Times, and academic journals, such as Distill, have demonstrated the power of interactivity within a prose context (i.e., not dashboards), NASA is still lagging in this area. A shift towards more interactive NASA publications will require new technology and expertise. In this presentation, we begin to explore the avenues that the Office of Technology, Policy, and Strategy are using to make its reports interactive by using results from the “Cost and benefit Analysis of Orbital Debris Remediation” as initial examples. We share our current findings and aim to start a discussion with other members of the NASA analytics community interested in or currently adding interactivity to Agency products.

data visualization↗
NASA NTRS2010

Risk Presentation Using the Three Dimensions of Likelihood, Severity, and Level of Control

Traditional hazard analysis techniques utilize a two-dimensional representation of the results determined by relative likelihood and severity of the residual risk. These matrices present a quick-look at the Likelihood (Y-axis) and Severity (X-axis) of the probable outcome of a hazardous event. A three-dimensional method, described herein, utilizes the traditional X and Y axes, while adding a new, third dimension, shown as the Z-axis, and referred to as the Level of Control. The elements of the Z-axis are modifications of the Hazard Elimination and Control steps (also known as the Hazard Reduction Precedence Sequence). These steps are: 1. Eliminate risk through design. 2. Substitute less risky materials for more hazardous materials. 3. Install safety devices. 4. Install caution and warning devices. 5. Develop administrative controls (to include special procedures and training.) 6. Provide protective clothing and equipment. When added to the two-dimensional models, the level of control adds a visual representation of the risk associated with the hazardous condition, creating a tall-pole for the leastwell-controlled failure while establishing the relative likelihood and severity of all causes and effects for an identified hazard. Computer modeling of the analytical results, using spreadsheets and three-dimensional charting gives a visual confirmation of the relationship between causes and their controls.

Watson, Clifford↗
NASA NTRS2011

Risk Assessment Using the Three Dimensions of Probability (Likelihood), Severity, and Level of Control

Traditional hazard analysis techniques utilize a two-dimensional representation of the results determined by relative likelihood and severity of the residual risk. These matrices present a quick-look at the Likelihood (Y-axis) and Severity (X-axis) of the probable outcome of a hazardous event. A three-dimensional method, described herein, utilizes the traditional X and Y axes, while adding a new, third dimension, shown as the Z-axis, and referred to as the Level of Control. The elements of the Z-axis are modifications of the Hazard Elimination and Control steps (also known as the Hazard Reduction Precedence Sequence). These steps are: 1. Eliminate risk through design. 2. Substitute less risky materials for more hazardous materials. 3. Install safety devices. 4. Install caution and warning devices. 5. Develop administrative controls (to include special procedures and training.) 6. Provide protective clothing and equipment. When added to the two-dimensional models, the level of control adds a visual representation of the risk associated with the hazardous condition, creating a tall-pole for the least-well-controlled failure while establishing the relative likelihood and severity of all causes and effects for an identified hazard. Computer modeling of the analytical results, using spreadsheets and three-dimensional charting gives a visual confirmation of the relationship between causes and their controls.

Watson, Clifford C.↗
NASA NTRS1993

Wave packet motion in harmonic potential and computer visualization

Wave packet motions of a single electron in harmonic potentials or a magnetic field are obtained analytically. The phase of the wave function which depends on both time and space is also presented explicitly. The probability density of the electron changes its width and central position periodically. These results are visualized using computer animation techniques.

Tsuru, Hideo↗
NASA NTRS1977

Effects of film injection angle on turbine vane cooling

Film ejection from discrete holes in the suction surface of a turbine vane was studied for hole axes (1) slanted 30 deg to the surface in the streamwise direction and (2) slanted 30 deg to the surface and 45 deg from the streamwise direction toward the hub. The holes were near the throat area in a five-row staggered array with 8-diameter spacing. Mass flux ratios were as high as 1.2. The data were obtained in an annular sector cascade at conditions where both the ratio of the boundary layer momentum thickness-to-hole diameter and the momentum thickness Reynolds number were typical of an advanced turbofan engine at both takeoff and cruise. Wall temperatures were measured downstream of each of the rows of holes. Results of this study are expressed as a comparison of cooling effectiveness between the in-line angle injection and the compound-angle injection as a function of mass flux ratio. These heat transfer results are also compared with the results of a referenced flow visualization study. Also included is a closed-form analytical solution for temperature within the film cooled wall.

Gauntner, J. W.↗
NASA NTRS2019

Cloud Giovanni: Reining in Costs and Improving Performance with Analytical Data Stores Using Scalable Serverless Architecture

Giovanni is the Geospatial Interactive Online Visualization ANd aNalysis Infrastructure developed at NASA GES DISC which provides a simple and intuitive way to visualize, analyze, and access vast amounts of Earth science data. It receives large number of user requests each day for a variety of analysis and visualization services, which leads to the big data challenge of serving gradually increasing large data volumes with diverse statistical algorithms. We hereby propose a multi-dimensional accumulation method which provides fast and cost-efficient cloud analysis for diverse services including both area averaging and time averaging. This method involves the weighted volume integration over multiple variable dimensions (time and space), and is implemented in AWS using Athena providing serverless and highly scalable data analysis. Compared to the standard method, this approach dramatically reduced the computational time by order of magnitude with a minimal AWS cost incurred. For example, for a benchmark of 10-year area averaging over the 1x1 degree daily variable, the computational time was reduced from minutes to seconds, and the Athena cost is only $5 for 100,000 requests.

Zhang, Hailiang↗
NASA NTRSDate not supplied

Celestial Mapping System

Celestial Mapping System (CMS) is a software platform developed by Dr. Agrawal’s team to generate virtual 3D globes for celestial bodies. Various layers are built on top of the virtual globe to provide visualization for high-resolution imagery, enable precise measurements, build analytical capabilities and broad range of functionalities to assist planetary scientists and mission planners. In her June 14th presentation, Dr. Agrawal will showcase the user interactive software platform to virtually travel the lunar terrain, place rovers and instruments on the surface of the moon and perform measurements of various geological features including permanently shadowed regions. Her team’s future goals include building interactive 3D globes for other planetary bodies such as Venus, Mars, and Titan in the solar system.

GIS system↗
NASA NTRS1978

The role of O-type neutral lines in magnetic merging during substorms and solar flares

An analytical model of O-type configurations was derived, for visualizing the geometry and for numerical treatment of plasma flows. It was found that at a certain distance from the neutral line the mean particle motion became decoupled from that of magnetic field lines (which obey the MHD condition). The decoupling distance depended on initial conditions in momentum space, suggesting that the MHD approximation which averages out such conditions may not suffice for describing plasma dynamics near the neutral line. It was also found that after inflowing particles are decoupled from the field line motion, they go over to a mode of runaway acceleration along the neutral line. It is concluded that if merging occurs at an X-O pair, two particle populations may be expected - low energy particles accelerated adiabatically by earthward convection past the X-type line and high-energy particles convected towards the O-type line. The second acceleration process depends critically on the rapidity of merging and is therefore expected to vary considerably from event to event.

Stern, D. P.↗
NASA NTRS1982

Comparison of analytical predictions of longitudinal short period pilot-induced oscillations with results from a simulation study of the space shuttle orbiter

An analytical analysis of conditions producing pilot induced oscillations (PIO's) was made for the space shuttle orbiter in a landing approach configuration for the task of milling the elevation angle of the line of sight to a target vehicle. The analysis yielded a value of PIO frequency and a value for the amount of total system time delay (pilot + control system) that can be tolerated before instability results. Calculations were performed showing the effect of varying the range to the target and of varying the handling qualities of the orbiter vehicle. Analytical predictions were compared with simulation results obtained using a visual motion simulator.

Riley, D. R.↗