Search NASASearch

SEARCH · Search NASA

Results for “weight distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Tissue fluid shift, forelimb loading, and tail tension in tail-suspended rats

The tail suspension model (head-down tilt) simulates hypogravity in terms of musculoskeletal loss in the rat. However, little is known of tissue fluid shifts and body weight distribution in this model. Tissue fluid pressures were measured by wick catheters in 12 Munich-Wistar rats before, during, and after 48 hrs of tail suspension (about 30 deg head-down tilt). Subcutaneous tissue fluid pressure in the neck increased from -2.2 + or - 0.4 (normal horizontal position) to +4.0 + or - 1.5 cm H2O during tail suspension, indicating a cephalic fluid shift and significant edema during head-down tilt. In a separate study, six rats were suspended at 30-70 deg, and forelimb load and tail tension were measured by a balance and force transducer, respectively. Approximately 50 percent of body weight (BW) was loaded on forelimbs at a head-down tilt angle of 30 deg and forelimb load declined linearly to 10 percent BW at 70 deg. Furthermore, tail tension increased from 50 percent BW at 30 deg to 85 percent BW at 70 deg. These results indicate that less than normal loads are applied to forelimbs of rats suspended at angles of less than 30 deg and that the tail bears an increasing proportion of the rat's body weight at head-down tilt angles of less than 30 deg.

Hargens, A. R.

Novel insight into the kinetics of amide bond glycolysis for nylon-6 depolymerization

Chemical recycling of nylon-6 to short-chain oligomers and monomer ε-caprolactam via catalytic glycolysis is a potential solution for plastic waste remediation. Here, in this work, the kinetics of amide bond glycolysis (with ethylene glycol) in nylon-6 and the model compound N-phenethyl-3-phenylpropanamide (M1) were evaluated at 473 K in the presence of the cyclic amidine catalyst 1,5,7-triazabicyclo[4.4.0]dec-5-ene. Rates of polymer glycolysis were determined by the time-dependent shift in molecular weight distribution, whereas rates of M1 glycolysis were determined using liquid chromatography. The similarity of the first-order rate constants for glycolysis of nylon-6 and M1 at 473 K with 0.03 M amidine catalyst (5 mol% relative to amide bonds), 1.22 × 10 −5 s −1 and 2.18 × 10 −5 s −1 , respectively, confirmed the suitability of M1 as a model compound for nylon-6 glycolysis. Similar rates of glycolysis in the presence of other cyclic amidine catalysts as well as sodium methoxide revealed little influence of base strength. Glycolysis rates were unexpectedly non-linear in catalyst loading and deactivation occurred with long reaction times, presumably by non-selective decomposition of products as detected by liquid chromatography.

Depolymerization rate and rate constant

Adsorption of terbium (III) on DGA and LN resins: Thermodynamics, isotherms, and kinetics

Two commercially available extraction chromatography (EXC) resins containing N,N,N’,N’-tetra-n-octyldiglycolamide (DGA Resin, Normal, 50 – 100 μm) and Bis(2-ethylhexyl) phosphate (LN Resin, 100 – 150 μm) were used as adsorbents to study fundamental adsorption properties such as thermodynamic values, equilibrium isotherms, and kinetic uptake models for terbium(III) adsorption. Weight distribution ratios (D w ) for terbium on DGA and LN resins were measured using a [ 160 Tb]Tb 3+ radiometric tracer in nitric acid as a function of acidity, temperature, initial analyte concentration, and equilibrium time. The D w values showed increasing binding affinity for DGA resin at high nitric acid concentrations and decreasing binding affinity for LN resins. Thermodynamic studies for DGA and LN resins revealed that the Gibbs free energy (ΔG) increased consistently with temperature. To model equilibrium data, increasingly higher parameter equilibrium isotherm models (Henry (1) < Langmuir, Freundlich (2) < Redlich-Peterson (3) < Fritz-Schluender (4)) were compared on their root mean squared errors (RMSE) and adjusted determination coefficients to determine the most applicable model. In all cases, the empirical four-parameter Fritz-Schluender isotherm demonstrated a superior fit. Similar comparisons for reaction-based kinetic models (Pseudo-first-order < Pseudo-second-order < Pseudo-n-order) revealed that the higher-order PNO model yielded a superior fit of kinetic data for both resins. Furthermore, in some cases, adsorption isotherms and kinetic models could also be modeled by a lower-order model with minimal change in error parameters. Weber-Morris plots revealed that two linear sections are observed for each resin, where the first linear segment is attributed to fast (film diffusion) adsorption of terbium, followed by slower intraparticle diffusion of terbium through the pores as the rate-limiting step. Based on the Weber-Morris plot, both film and intraparticle diffusion are involved in controlling the kinetic rate of adsorption for DGA and LN resins.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA

The developments in modifying functionality of lignin and its application in biocomposites

With the advancement of sustainable material innovations, renewable natural biopolymers are gradually replacing traditional metal and petroleum-based synthetic materials due to their environmental friendliness, biodegradability, and economic advantages. Lignin, the second most abundant natural aromatic polymer in the plant kingdom, has emerged as a key candidate raw material for the development of green polymer systems because of its unique phenylpropane unit network structure, high carbon content, and rich functional group characteristics. However, challenges such as the inherent structural complexity, chemical inertness, and uneven molecular weight distribution of lignin limit its direct application. By employing modification strategies such as chemical functionalization and physical regulation, researchers can precisely control its reactivity, thermal stability, and interfacial compatibility, enabling the preparation of high-performance lignin-based functional composites. Here, this paper systematically reviews the principles and methodological advancements in lignin's multi-dimensional modification technology. It analyzes the mechanisms by which various chemical and physical modification techniques enhance the mechanical properties, functional responsiveness, and environmental adaptability of materials, and discusses innovative applications in fields such as intelligent packaging, biomedical materials, and energy storage devices. Furthermore, this review addresses the key challenges encountered in the high-value transformation of lignin, with the aim of offering a theoretical framework and technical pathway for the transformative development of lignin from agricultural and forestry by-products to functional material platforms.

Functional composites

Molten-Phase Unsaturation Enhanced Pyrolytic Upcycling of Polyolefins

Fast pyrolysis is a robust deconstruction technology for chemically upcycling waste plastics without losing significant carbon to noncondensable gases. However, fast pyrolysis of polyolefins often produces hydrocarbons with broad molecular weight distributions, mainly waxes, which can also negatively affect the commercial reactor operation and downstream upgrading of the products. We discovered that combining molten-phase thermal treatment with subsequent fast pyrolysis offers a facile method to enhance polyolefin pyrolysis and catalytic upgrading. The molten-phase thermal treatment increased unsaturated C–C bonds in the treated polyolefins. During subsequent pyrolysis, the preheated polyolefins significantly reduced wax range hydrocarbons in the condensable products without an increase in gas formation. Here, the wax yields from pyrolysis of high-density polyethylene (HDPE) preheated to 295 °C and low-density polyethylene (LDPE) preheated to 275 °C were 20.5% and 26.5%, respectively, compared to 38.6% and 46% produced from pyrolyzing untreated polyolefins. When catalytically pyrolyzed using a zeolite catalyst, the preheated polyolefins promoted higher yields of olefins during ex-situ catalytic pyrolysis and higher yields of aromatic hydrocarbons during in-situ catalytic pyrolysis. During ex-situ catalytic pyrolysis, ethylene yields were 23.3% and 24.7% for the preheated HDPE and LDPE compared to 16.7% and 9.3% for untreated HDPE and LDPE, respectively.

Aromatic compounds

Effect of Initiator Density, Catalyst Concentration, and Surface Curvature on the Uniformity of Polymers Grafted from Spherical Nanoparticles

Polymer-grafted nanoparticles (PGNPs) are versatile hybrid materials whose properties critically depend on brush dimensions, uniformity, and grafting density. Herein, we systematically investigated how initiator density, catalyst concentration, and nanoparticle curvature govern the growth of poly(methyl methacrylate) (PMMA) brushes grafted from spherical SiO 2 nanoparticles via surface-initiated activators regenerated by electron transfer atom transfer radical polymerization (SI-ARGET ATRP). By tuning the initiator density through a combination of “active” and “dummy” silane initiators anchored on the nanoparticles’ surface and controlling the catalyst concentration, we reveal that increased initiator crowding and smaller surface curvature amplify steric hindrance, leading to decreased initiation efficiency and broader molecular weight distributions. Correlation with the corresponding unattached chains by ARGET ATRP suggests the presence of permanently inaccessible (“buried”) initiation sites, which are a characteristic of surface-grafted systems. At sufficient Cu catalyst concentrations, uniform brush growth is attained across different initiator densities, whereas decreased catalyst concentrations accentuate nonconcurrent initiation and propagation. These findings provide mechanistic insights into the interplay of initiator density, catalyst concentration, and surface curvature, offering design principles for tailoring the PGNP architecture. These results can guide the structural engineering of densely grafted surfaces, including nanoparticles and flat substrates, for applications in nanocomposites, photonics, and functional coatings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH

Exploring Microphase Separation in Semi-Fluorinated Diblock Copolymers: A Combined Experimental and Modeling Investigation

We report the combined experimental and theoretical study of the bulk self-assembly behavior of polystyrene-blockpoly( 2,3,4,5,6-pentafluorostyrene) diblock copolymers. These block copolymers were designed to create highly antagonistic blocks (with a high Flory−Huggins interaction parameter, χ) with minimum disruption to the molecular construct (i.e., only replacing five hydrogen atoms with five fluorine atoms). A large library of diblock copolymers (41 samples) was synthesized by reversible addition− fragmentation chain transfer (RAFT) polymerization to map out a major portion of the phase space. All block copolymers exhibited narrow molecular weight distributions with dispersity (D) values between 1.07 and 1.32, and subsequent thermal annealing revealed phase separation into well-defined nanoscale morphologies depending on their molecular composition, as determined from small-angle X-ray scattering and transmission electron microscopy analyses, with an experimental phase diagram being constructed. The χ value at 25 °C for this block copolymer was estimated to be 0.2 using strong segregation theory, based on trends in phase-separated domain spacing and interfacial width. When applying theoretical approaches, the majority of the domain spacing data trends were captured by a coil−coil diblock copolymer model; however, a better fit to the data for samples with shorter fluorinated blocks was obtained with a rod−coil model, indicating that the chains in these fluorinated blocks likely have a higher inherent stiffness and were thus rod-like. This observation demonstrates that, due to the very high value of χ, a transition from coil−coil to rod−coil behavior can be obtained purely by reducing the length of the stiffer of the two blocks and without varying temperature or the chemical composition of the polymers. Here, this work showcases the presence of strong microphase separation within AB diblock copolymers despite the relatively similar chemical composition of the constituent “A” and “B” units, with a clear transition from rod−coil to coil−coil segregation behavior.

RAFT polymerization

Improving statistical precision in Monte Carlo samples with negative weights via reweighting and uncertainty quantification

High statistical precision is critical for Monte Carlo (MC) samples in high energy physics and is degraded by negatively weighted events. This paper investigates a procedure to learn the relationship between the negative and positive weight distributions of any sample, allowing the reduction of statistical uncertainty by reweighting kinematically equivalent events with the same sign. A robust uncertainty quantification method is required for the practical application of such method. Two methods for the estimation of the reweighting uncertainty are developed: one at the event and another one at the final observable level. The latter method is strongly favored. The gains in statistical precision are then quantified. The method is demonstrated on Sherpa vector boson plus jets samples when using all generated events and when restricted to the signal region of a mock analysis. It is demonstrated to significantly reduce stochastic behavior in sparse MC samples while decreasing the overall uncertainty with a sufficiently well-known reweighting function.

Monte Carlo methods

Dual-unitary shadow tomography

We introduce a classical shadow tomography scheme based on dual-unitary brick-wall circuits termed "dual-unitary shadow tomography" (DUST). For this we study operator spreading and Pauli weight dynamics in one-dimensional qubit systems, evolved by random two-local dual-unitary gates arranged in a brick-wall structure, ending with a final measurement layer. We do this by deriving general constraints on the Pauli weight transfer matrix and specializing to the case of dual-unitarity. We first show that dual-unitaries must have a minimal amount of entropy production. Remarkably, we find that operator spreading in these circuits have a rich structure resembling that of relativistic quantum field theories, with massless chiral excitations that can decay or fuse into each other, which we call left- or right-movers. We develop a mean-field description of the Pauli weight in terms of $\rho(x,t)$, which represents the probability of having nontrivial support at site $x$ and depth $t$ starting from a fixed weight distribution. We develop an equation of state for $\rho(x,t)$, and simulate it numerically using Monte Carlo simulations. Lastly, we demonstrate that the fast-thermalizing properties of dual-unitary circuits make them better at predicting large operators than shallow brick-wall Clifford circuits. Our results are robust to finite-size effects due to the chirality of dual-unitary brick-wall circuits.

97 MATHEMATICS AND COMPUTING

Effect of cavitation on fluid stability in polymer thickened fluids and lubricants

The effects of cavitating flow on the polymeric additives used in functional fluids are described. A comparison of thermal and mechanical stability tests for these polymer solutions show distinct differences in the machanism of the polymer degradation. The thermal degradation tests appear to cause an unzippering or depolymerization type of reaction in which there is no particular selectivity based on molecular weight. The mechanical degradation of these fluids appears to be based on molecular weight. Measurements of molecular weight distributions during mechanical degradation show that for a given level of intensity only molecules above a certain minimum size are degraded. The effects of ultrasonic radiation on polymer degradation are reported. Tests were conducted to demonstrate the mechanism of mechanical polymer degradiation in an orifice. A more severe test than the orifice test in which two tapered roller bearings loaded against each other produce the mechanical breakdown is discussed.

Duda, J. L.

Effect of sterilization irradiation on friction and wear of ultrahigh-molecular-weight polyethylene

The effect of sterilization gamma irradiation on the friction and wear properties of ultrahigh molecular weight polyethylene (UHMWPE) sliding against 316L stainless steel in dry air at 23 C was determined. A pin-on-disk apparatus was used. Experimental conditions included a 1-kilogram load, a 0.061- to 0.27-meter-per-second sliding velocity, and a 32000- to 578000-meter sliding distance. Although sterilization doses of 2.5 and 5.0 megarads greatly altered the average molecular weight and the molecular weight distribution, the friction and wear properties of the polymer were not significantly changed.

Jones, W. R., Jr.

Low-thrust vehicles concept studies

Low thrust chemical (hydrogen-oxygen) propulsion systems configured specifically for low acceleration orbit transfer of large space systems were studied in order to provide the required additional data to better compare new, low thrust chemical propulsion systems with other propulsion approaches such as advanced electric systems. Study results indicate that it is cost-effective and least risk to combine the low thrust OTV and stowed spacecraft in a single 65 K shuttle. Mission analysis indicates that there are 25 such missions, starting in 1987. Multiple shuttles (LSS in one, OTV in another) result in a 20% increase in LSS (SBR) diameter over single shuttle launches. Synthesis and optimization of the LSS characteristics and OTV capability resulted in determination of the optimum thrust-to-weight and thrust level. For the space based radar with radial truss arms (center thrust application), the optimum thrust-to-weight (maximum) is 0.1, giving a thrust of 2000 lb. For the annular truss (edge-on thrust application) the structure is not as sensitive, and thrust of 1000 lb appears optimum. For the geoplatform, optimum T/W is .15 (3000 lb thrust). The effects of LSS structure material, weight distribution, and unit area density were evaluated, as were the OTV engine thrust transient and number of burns.

Ketchum, W. J.

Some fighter aircraft trends

Some basic trends in fighters are traced from the post World II era. Beginning with the first operational jet fighter, the P-80, the characteristics of subsequent fighter aircraft are examined for performance, mission capability, effectiveness, and cost. Characteristics presented include: power loading, wing loading, maximum speed, rate of climb, turn rate, weight and weight distribution, cost and cost distribution. The characteristics of some USSR aircraft are included for comparison. The trends indicate some of the rationale for certain fighter designs and some likely characteristics to be sought in future fighter aircraft designs.

Spearman, L.

Structure and properties of polyethylene films used in heavy lift balloons

The following features of five polyethylene films used by NASA in the construction of heavy lift balloons have been examined: molecular weight, molecular weight distribution, branching, melting behavior, density, surface texture, birefringence, orientation of crystalline regions, unlaxial deformation in the machine and transverse directions, and the effect of sample geometry and strain rate on deformation behavior. The goal of this exploratory study was to determine whether there are significant differences in any of the above mentioned features, or combination of features between the films. The acquisition of such information is a first step towards determining whether there are any specific correlations between film characteristics and the incidence of catastrophic failure of balloons during ascent through the troposphere. This exploratory study has resulted in the identification of similarities and differences between various features of the films.

Khoury, F.

Some fighter aircraft trends

Some basic trends in fighter aircraft are traced from the post World War II era. Beginning with the first operational jet fighter, the P-80, the characteristics of subsequent fighter aircraft are examined in terms of performance, mission capability, effectiveness, and cost. Characteristics presented include such items as power loading, wing loading, maximum speed, rate of climb, turn rate, weight and weight distribution, cost and cost distribution. In some cases, the characteristics of U.S.S.R. aircraft are included for comparison. The trends indicate some of the rationale for certain fighter designs and indicate some likely characteristics to be sought in future fighter aircraft designs.

Spearman, M. L.

Space Station based options for orbiter docking/berthing

Conceptual efforts to develop a Space Station based system for docking and/or berthing the NSTS Orbiter are described. Past docking and berthing systems are reviewed, the general requirements and options for mating the Orbiter and Space Station are discussed, and the rationale for locating the system on the Station is established. One class of Station-based system is developed in several variations and evaluated with respect to weight distribution, loads, safety, reliability, viewing, and maintainability. An evolutionary presentation of the variations provides insight into the development process and the problems encountered. An overall evaluation of the Station-based variations compared to an optimized Orbiter-based system demonstrates the potential benefits of this approach as well as the issues that must be resolved to realize the benefits.

Hoover, Daniel J.

Bomber design trends

Some basic trends in bomber aircraft are traced from the pre-World War I era to the present time. The historic review includes bombers of many countries. The primary discussion, however, will be based on U.S. bomber programs and, to the extent possible, on USSR bomber programs. The bomber aircraft will be examined in terms of performance and mission capability.Characteristics will include power or thrust loading, wing loading, maximum speed, cruising speed, weight and weight distribution, and payload. These trends can be used to indicate the rationale for certain design types. Performance characteristics can be used to indicate potential mission objectives. The overall design trends should be useful in revealing the influence of mission objectives, the influence of advanced technology and, in turn, may be useful in predicting likely future trends.

Spearman, M. L.