Search NASA⌕ Search

SEARCH · Search NASA

Results for “wind blade manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A gravo-aeroelastically scaled wind turbine rotor at field-prototype scale with strict structural requirements

A new sub-scale field-prototype design solution is developed to realize the dynamics, structural response, and distributed loads (gravitational, aerodynamic, centrifugal) that are characteristic of a full-scale large, modern wind turbine rotor. Prior work in sub-scale wind turbine testing has focused on matching aerodynamic/aero-elastic characteristics of full-scale rotors at wind tunnel scale. However, large-scale rotor designs must expand beyond this limited set of scaling parameters for cost-effective prototyping and meet strict requirements for structural safety for field testing. Here, the challenge lies in producing a structural design meeting two competing objectives: novel scaling objectives that prescribe the sub-scale blade to have low mass and stiffness; and traditional structural safety objectives that drive the design to have higher stiffness and mass. A 20% gravo-aeroelastically scaled wind turbine blade is developed successfully that satisfies these competing objectives. First, it achieved close agreement for non-dimensional tip deflection and flap-wise blade frequency (both within 2.1%) with a blade mass distribution constrained to produce target gravitational and centrifugal loads. Second, the entire blade structure was optimized to ensure a safe, manufacturable solution meeting strict strength requirements for a testing site that can experience up to 45 m/s wind gusts. The prototype-scale blade was fabricated and successfully proof-load tested.

17 WIND ENERGY↗
DOE OSTI2022

Land-based wind turbines with flexible rail-transportable blades – Part 2: 3D finite element design optimization of the rotor blades

Abstract. Increasing growth in land-based wind turbine blades to enable higher machine capacities and capacity factors is creating challenges in design, manufacturing, logistics, and operation. Enabling further blade growth will require technology innovation. An emerging solution to overcome logistics constraints is to segment the blades spanwise and chordwise, which is effective, but the additional field-assembled joints result in added mass and loads, as well as increased reliability concerns in operation. An alternative to this methodology is to design slender flexible blades that can be shipped on rail lines by flexing during transport. However, the increased flexibility is challenging to accommodate with a typical glass-fiber, upwind design. In a two-part paper series, several design options are evaluated to enable slender flexible blades: downwind machines, optimized carbon fiber, and active aerodynamic controls. Part 1 presents the system-level optimization of the rotor variants as compared to conventional and segmented baselines, with a low-fidelity representation of the blades. The present work, Part 2, supplements the system-level optimization in Part 1 with high-fidelity blade structural optimization to ensure that the designs are at feasible optima with respect to material strength and fatigue limits, as well as global stability and structural dynamics constraints. To accommodate the requirements of the design process, a new version of the Numerical Manufacturing And Design (NuMAD) code has been developed and released. The code now supports laminate-level blade optimization and an interface to the International Energy Agency Wind Task 37 blade ontology. Transporting long, flexible blades via controlled flapwise bending is found to be a viable approach for blades of up to 100 m. The results confirm that blade mass can be substantially reduced by going either to a downwind design or to a highly coned and tilted upwind design. A discussion of active and inactive constraints consisting of material rupture, fatigue damage, buckling, deflection, and resonant frequencies is presented. An analysis of driving load cases revealed that the downwind designs are dominated by loads from sudden, abrupt events like gusts rather than fatigue. Finally, an analysis of carbon fiber spar caps for downwind machines finds that, compared to typical carbon fibers, the use of a new heavy-tow carbon fiber in the spar caps is found to yield between 9 % and 13 % cost savings.

17 WIND ENERGY↗
DOE OSTI2021

Benchmarks of Global Clean Energy Manufacturing, 2014-2016

Benchmarks of Global Clean Energy Manufacturing provides an assessment of the global state of clean energy manufacturing over 3 years from 2014 to 2016. Four technologies were examined - wind turbine components (blade, tower, nacelle), crystalline silicon (c-Si) solar photovoltaic (PV) modules, light-duty vehicle (LDV) lithium-ion battery (LIB) cells, and light-emitting diode (LED) packages for lighting and other consumer products. The analysis looked along each technology's manufacturing supply chain, including processing raw materials, producing required subcomponents, and assembling final products. Manufacturing supply chains were evaluated across 13 economies that are the primary manufacturing hubs for these technologies. This Highlights summary report features key findings across the manufacturing supply chains.

42 ENGINEERING↗
DOE OSTI2022

Wind turbine blade design with airfoil shape control using invertible neural networks

Wind turbine blade design is a highly multidisciplinary process that involves aerodynamics, structures, controls, manufacturing, costs, and other considerations. More efficient blade designs can be found by controlling the airfoil cross-sectional shapes simultaneously with the bulk blade twist and chord distributions. Prior work has focused on incorporating panel-based aerodynamic solvers with a blade design framework to allow for airfoil shape control within the design loop in a tractable manner. Including higher fidelity aerodynamic solvers, such as computational fluid dynamics, makes the design problem computationally intractable. In this work, we couple an invertible neural network trained on high-fidelity airfoil aerodynamic data to a turbine design framework to enable the design of airfoil cross sections within a larger blade design problem. We detail the methodology of this coupled framework and showcase its efficacy by aerostructurally redesigning the IEA 15-MW reference wind turbine blade. The coupled approach reduces the cost of energy by 0.9% compared to a more conventional design approach. This work enables the inclusion of high-fidelity aerodynamic data earlier in the design process, reducing cycle time and increasing certainty in the performance of the optimal design.

17 WIND ENERGY↗
DOE OSTI2023

Numerical Manufacturing And Design tool

NuMAD helps to enable efficient creation and use of high fidelity wind turbine blade models for structural and aerodynamic analysis. NuMAD is a GUI-based tool used to manage the specific geometry and materials inputs required to fully describe a wind turbine blade.

Berg, Jonathan↗
DOE OSTI2024

Structural Characterization of Deployed Thermoplastic and Thermoset Composite Tidal Turbine Blades

The National Renewable Energy Laboratory worked with Verdant Power to manufacture, and characterize, novel thermoplastic composite blades on their Gen5d 5 m diameter turbines at the Roosevelt Island Tidal Energy (RITE) site in the East River in N.Y. to demonstrate a low-cost manufacturing process for marine energy structures. Verdant had designed, manufactured, and deployed epoxy thermoset composite blades on three Gen5d turbines in October 2020. At a maintenance cycle in May 2021, a Gen5d turbine equipped with the NREL thermoplastic blades was deployed and retrieved in October 2021. Modal, static and fatigue structural characterization was performed on both blade types before and after the deployment. The static and modal test results showed that the thermoplastic blades were slightly stiffer than the epoxy blades both dry and after the deployment. The epoxy blades had about 8% increase in strain at the applied load after the deployment, whereas the thermoplastic blade strains were not changed significantly. Ultimately the thermoplastic blade failed during fatigue testing due to a crack which is thought to have initiated between the internal foam and the laminate at the location of the internal instrumentation. The Verdant Power Gen5d epoxy blades did not have this internal instrumentation and did not have this failure, performing adequately through the operational period. A lack of design information and fatigue data for both the thermoplastic laminates and the adhesive used means that further work is needed to fully understand his failure and the root cause analysis is ongoing. This paper provides details on the thermoplastic blade manufacturing, materials, test methodology and results.

17 WIND ENERGY↗
DOE OSTI2025

Acetolysis for Epoxy-Amine Carbon Fibre-Reinforced Polymer Recycling

Carbon fibre-reinforced polymers (CFRPs) are used in many applications in the global energy transition, including for lightweighting aircraft and vehicles and in wind turbine blades, shipping containers and gas storage vessels1,2,3,4. Given the high cost and energy-intensive manufacture of CFRPs5,6,7, recycling strategies are needed that recover intact carbon fibres and the epoxy-amine resin components. Here we show that acetic acid efficiently depolymerizes both aliphatic and aromatic epoxy-amine thermosets used in CFRPs to recoverable monomers, yielding pristine carbon fibres. Deconstruction of materials from multiple sectors demonstrates the broad applicability of this approach, providing clean fibres from 2 h reactions. The optimal conditions were scaled to 80.0 g of post-consumer CFRPs, and demonstrative composites were fabricated from the recycled carbon fibres, which were recycled two more times, maintaining their strength throughout. Process modelling and techno-economic analysis, with feedstock cost informed by wind turbine blade waste generation8, indicates this method is cost effective, with a minimum selling price of US$1.50 per kg for recycled carbon fibres whereas life cycle assessment shows process greenhouse gas emissions around 99% lower than virgin carbon fibre production. Overall, this approach could enable recycling of industrial CFRPs as it provides clean, mechanically viable recycled carbon fibres and recoverable resin monomers from the thermoset.

09 BIOMASS FUELS↗
DOE OSTI2021

Land-Based Wind Market Report: 2021 Edition

The U.S. Department of Energy's 2021 edition of its land-based wind market report provides an overview of key trends in the U.S. wind power market, with a focus on 2020. You can find a report, data file and presentation on the Files tab, below. Additionally, several data visualizations are available on the Visualizations tab. Highlights of this year’s update include: -Wind comprises a growing share of electricity supply: U.S. wind power capacity grew at a record pace in 2020, with 25 billion dollars invested in 16.8 GW of capacity. Wind energy output rose to account for more than 8% of the entire nation’s electricity supply, and is more than 20% in 10 states. At least 209 GW of wind are seeking transmission interconnection; 61 GW of this capacity are offshore wind and 13 GW are hybrid plants that pair wind with storage or PV. -Wind project performance has increased over time: The average capacity factor among recently built projects was over 40%, considerably higher than projects built earlier. The highest capacity factors are seen in the interior ‘wind belt’ of the country. -Turbines continue to get larger: Improved plant performance has been driven by larger turbines mounted on taller towers and featuring longer blades. In 2010, no turbines employed blades that were 115 meters in diameter or larger, but in 2020, 91% of newly installed turbines featured such rotors. Proposed projects indicate that total turbine height will continue to rise. -Low wind turbine pricing has pushed down installed project costs over the last decade: Wind turbine prices are averaging 775–850 dollars/kW. The average installed cost of wind projects in 2020 was 1,460 dollars/kW, down more than 40% since the peak in 2010, though stable for the last three years. The lowest costs were found in Texas and the (non-ISO) West. -Wind energy prices remain low, around 20 dollars/MWh in the interior of the country: After topping out at 70 dollars/MWh for power purchase agreements (PPAs) executed in 2009, the national average price of wind PPAs has dropped. In the interior ‘wind belt’ of the country, recent pricing is around 20 dollars/MWh. In the West and East, prices tend to average 30 dollars/MWh or more. These prices, which are possible in part due to federal tax support, fall below the projected future fuel costs of gas-fired generation. -Wind PPA prices are often attractive compared to wind’s grid-system market value: The value of wind in wholesale power markets is affected by the location of wind plants, their hourly output profiles, and how those characteristics correlate with real-time electricity prices and capacity markets. The market value of wind declined in 2020, following natural gas prices lower and averaging under 15 dolalrs/MWh in ERCOT, MISO, NYISO and SPP; higher values were seen in CAISO, ISO-NE and PJM. -The average levelized cost of wind energy is down to 33 dollars/MWh: Levelized costs, which exclude the impacts of federal tax incentives, vary across time and geography, but the national average stood at 33 dollars/MWh in 2020—down substantially historically, though consistent with the previous two years. Levelized costs were lowest in ERCOT, SPP, and the (non-ISO) West. -The health and climate benefits of wind in 2020 were larger than its grid-system value, and the combination of all three far exceeds the current levelized cost of wind: Wind generation reduces power-sector emissions of carbon dioxide, nitrogen oxides, and sulfur dioxide. These reductions, in turn, provide public health and climate benefits that vary regionally, but together are economically valued at an average of 76 dollars/MWh-wind nationwide in 2020. -The domestic supply chain for wind equipment is diverse: For wind projects recently installed in the U.S., domestically manufactured content is highest for nacelle assembly (>85%), towers (60-75%), and blades and hubs (30-50%), but is much lower for most components internal to the nacelle.

17 WIND ENERGY↗
DOE OSTI2022

Agent-Based Modeling for the Circular Economy: Lessons Learned From Three Case Studies

The circular economy (CE) aims at decoupling human activities from resource use, creating wealth in the process. Recently, many scholars have questioned the link between increased circularity and sustainability, resulting in many methodological approaches being developed for that purpose. This presentation summarizes the insights gained from the application of agent-based modeling (ABM) to study the techno-economic and social conditions promoting circularity and sustainability of three technologies: photovoltaic (PV) modules, hard disk drives (HDDs), and wind blades. Four main categories of agents are defined in the ABM: asset owners, service providers (e.g., refurbishers), recyclers, and manufacturers. Two main CE strategies are represented: lifetime extension (through repair or reuse) and recycling. The developed models start by projecting installed capacities and end-of-life (EOL) quantities. Then the theory of planned behavior - a social psychology model explaining behavior adoption based on attitude, peer influence, and costs - is used to model the asset owners' EOL decision (i.e., landfill, recycle or extend the lifetime of the asset). Then, the quantities of assets flowing to the recycler and service provider agents and quantities of materials flowing to manufacturers are computed. Recyclers' economies of scale are dynamically modeled, and the value generated by the CE strategies for the recyclers, service providers, and manufacturers is computed within the model. When data are available, avoided greenhouse gas emissions resulting from the CE strategies adoption are calculated exogenously from the ABM simulations. Results show that with improved used PV modules warranties, the reuse CE strategy adoption increases from 1% to 23% between 2020 and 2050. Similarly, improved standards could enhance HDDs end-users trust in data-wiping - a prerequisite to reuse - leading to a 3-fold increase in the reuse rate and avoid about 5 million tons of CO2 eq by 2050. Regarding wind blades, 5-15 years lifetime extension could reduce EOL blade quantities by 13%. High costs and logistic issues prevent blades from being recycled in greater quantities. One insight from the case studies is the necessity to have mature secondary markets for reuse to be a viable option. Interestingly, PV reuse is limited by the willingness of PV owners to purchase used modules (on the demand side), while HDDs reuse is constrained by the lack of trust toward data-wiping (limiting the supply of used HDDs). The six limits of the CE concepts presented by Korhonen et al. (2018) are finally used to interpret the results. The HDD case study is an exemplary lock-in, where the first accepted practice (shredding) retains most of the market. The PV results illustrate the technical limitation to reuse, as the growing demand cannot be supplied entirely with used PV modules. The wind case study shows the relevance of clearly defining physical flows - what type of waste should wind blades be considered, how should they be transported and landfilled? - a crucial consideration that also applies to PV modules. Finally, the three case studies highlight the relevance of studying a technology's technical, economic, and market material efficiency potentials altogether and the potential benefit of coupling ABM to life cycle assessment.

agent-based modeling↗
DOE OSTI2021

ExaWind: Predictive Wind Energy Simulations

This presentation describes the ExaWind project and the team's progress in creating a suite of performance-portable codes designed for predictive simulations of wind farms on next-generation exascale-class supercomputers. Such simulations will require the resolution of scales spanning many orders of magnitude, from blade boundary layers to wind farm flow structures. In the U.S., the first exascale systems will be GPU accelerated, and different GPU manufacturers have been chosen for the different systems. At the heart of the ExaWind software is a hybrid-solver approach based on the codes Nalu-Wind and AMR-Wind, which are computational fluid dynamics solvers for the incompressible Navier-Stokes equations. Nalu-Wind is an unstructured-grid code used to resolve wind turbine geometry and blade boundary layers, whereas AMR-Wind is a structured-grid background solver for atmospheric turbulent flow and turbine wake propagation. The models are coupled with overset meshes and global linear systems are approximated through a loose-coupling algorithm. Results will include validation-quality high-fidelity simulations and strong/weak scaling results from the Summit supercomputer.

49 EE - Wind and Water Power Program - Wind (EE-4W↗
DOE OSTI2024

Enhanced joining strength in additive-manufactured polylactic-acid structures fused by embedded heated metallic meshes

Additively manufactured thermoplastic polymers, such as polylactic acid (PLA), hold significant promise for sustainable engineering structures, including wind turbine blades. Upscaling these structures beyond the limitations of 3D printer build volumes is a challenge; fusion joining presents a potential solution. This paper introduces a displacement-controlled resistance welding process for PLA, as an alternative to the typical force-controlled methods. Here, we investigated the bonding quality of resistance-welded and adhesive-bonded PLA beams through three-point bending and measured the surface deformations using digital image correlation. Different metal meshes (30%/0.11 mm Ni—Cu, 34%/0.07 mm Ni—Cu, and 36%/0.25 mm Co—Ni) served as heating elements. The process parameters were varied for the 34%/0.07 mm Ni—Cu mesh to identify an optimum set of parameters. Results showed that this optimized displacement-controlled welding achieved 94% of the original strength of monolithic samples. This indicates that the new welding process not only ensures high-quality bonding and fine surface finishing but also promotes sustainability, recyclability, and economic efficiency in various polymer and composite structural applications.

Additive manufacturing↗
DOE OSTI2022

Development of an open-source segmented blade design tool

As wind turbines continue to grow ever larger to reduce the cost of energy, their blades follow suit, with the largest commercial offshore blades extending past 100 m. Massive blades such as these raise key transportation and manufacturing challenges, especially for land-based turbines. Segmented blades are one solution and are garnering increased industry and research interest. In this work, a detailed mechanical joint model is integrated into the Wind-Plant Integrated System Design and Engineering Model (WISDEM ® ), which will facilitate future segmented blade research and optimization. WISDEM is used to design a wind turbine with 100-m segmented blades. This wind turbine design is compared to other machines with 100-m monolithic blades designed for rail-transportability. The designs are compared in terms of blade mass and cost, turbine capital cost, annual energy production, and levelized cost of energy, with monolithic designs being the lightest and most economical. However, this result may vary by wind plant location. A variety of segmentation joint types exist, and they will inevitably vary in parameters such as cost, spanwise location, and physical characteristics. This work examines the sensitivity of wind turbine design drivers and annual energy production to a variety of the aforementioned parameters, using the open-source wind turbine design codes OpenFAST and WISDEM, finding that joint mass, stiffness, and location can have significant effects on design drivers.

17 WIND ENERGY↗
DOE OSTI2024

Offshore Wind Turbine Blade (85 to120meters ultra-long blade) static and fatigue test

Offshore blades are not just longer, they are wider, heavier and more flexible. These longer blades are a key component of larger wind turbines and for turbines to be more efficient in low wind speeds. These longer blades help reduce the LCOE further and make offshore wind even more competitive. As described earlier, it is essential for the blades to be fully tested to verify and validate the blade designs and manufacturing processes to ensure a reliable product is installed in the field. Through this project WTTC developed and procured new testing equipment required to test longer blades with larger deflections and higher loads. R&D’s BCDA system commissioned was the largest fatigue test exciter system in the world and set the bar for other blade testing facilities worldwide.

17 WIND ENERGY↗
DOE OSTI2025

The Triple Catalytic Action of Tertiary Nitrogen Catalysts in Recyclable Epoxy-Anhydride Thermosets

The thermosetting polymer matrix in fiber reinforced composites is an important component for energy related applications, such as the lightweighting of vehicles or their use in wind and waterpower turbine blades, due to their ability to provide superior adhesion, stiffness, and applicability to a wide range of manufacturing processes. Despite these benefits, today's thermosets are widely considered to be unrecyclable; thus, there is a large interest in redesigning these materials to be inherently recyclable so that energy intensive production of fibers and monomers can be circumvented, bolstering composite manufacture supply chains. Polyester covalent adaptable networks (PECANs) are one such promising alternative to the incumbent, nonrecyclable epoxy-amine thermosets. PECANs can be formed from the ring-opening co-polymerization (ROCOP) of epoxy-anhydride monomer mixtures and subsequent curing at mild temperatures to exhibit similar performance to conventional epoxies while also possessing unique dynamic chemistries along the ester-hydroxyl backbone that are capable of transesterification and thus reprocessability. While significant advancements have been made in formulating these materials for improved mechanical properties or optimizing solvolysis and reprocessing strategies, less attention has been placed on the impact of the residing amine catalyst used to generate the polyester network. In this work, we evaluated the triple-catalytic efficacy of 12 tertiary amines that act as a curing (bulk ROCOP), a transesterification (internal bond exchange), and a deconstruction (methanolysis) catalyst for PECAN thermosets. Specifically, we first distinguish between chain-growth and step-growth polymerization mechanisms for epoxy-amine and epoxy-anhydride mechanisms. We also utilized density functional theory (DFT) to estimate the basicity (pKb) of each catalyst. Of the tested catalysts, the ROCOP of the studied PECAN network can be completed between 95 and 247 min (at 80 degrees C), with variable gelation phenomena. Additionally, the stress relaxation (transesterification metric) efficiency of the tested PECAN networks with alternative embedded catalysts ranged from 95% to 15% reduction in stress after 5 h at 200 degrees C, and the depolymerization efficacy ranged from 2.5% to 9.8% deconstruction after 36 h at 130 degrees C. Overall, the nitrogen-based moieties were demonstrated to influence polymerization kinetics, catalyze the dynamic transesterification exchange mechanism, and aid in the solvolysis of the thermosets at end-of-life.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of recycled fibers and shredded intermediates variation on the mechanical properties and energy absorption of fiber‐reinforced composite panels

Abstract The global composite industry generates large quantities of waste which mostly ends up in landfills due to a lack of established end‐use applications for multiple waste streams. The scrap from end‐of‐life (EoL) includes manufacturing waste such as dry chopped fiber tows, loose fibers, shredded fibers from fabric textile operations, cured/semi‐cured prepregs, and fully cured composite structure waste from aircraft, automobiles, wind blades, boats, and pressure vessels. In this work, different composite waste streams were reduced to shredded intermediates, followed by simple blending, and subjected to wet compression molding to produce composite panels. The panels/plaques were tested for mechanical properties (flexure and impact), fiber‐matrix wet‐out, and property bounds. It was found that wet‐compression molding was a viable and scale‐able approach to produce recycled panels from EoL composites shredded scrap. Furthermore, full‐scale size panels for use in truck bodies and intermodal shipping container flooring were manufactured and their impact resistance was tested using a drop weight impact test. They were tested both for high‐ and low‐velocity load. In the case of high‐velocity load, the average impact load was 14,673 N; the average absorbed energy was 101.6 J; the average elastic energy was 11.7 J and the impact resistance was 1065 J/m. In the case of the low‐velocity drop weight impact test, it was found that the average impact load was 7877.358 N; the average absorbed energy was 9.718 J; the average elastic energy was 9.14 J, and the impact resistance was 184.1 J/m. The shredded composite was shown to be a candidate material for the manufacture of truck bodies and intermodal containers’ flooring panels. Highlights By using shredded intermediates from different composite waste streams, it is possible to manufacture composite panels. Wet–compression process is an appropriate technique for manufacturing recycled fiber composite panels. Regardless of the source of scrap, the mechanical properties of the produced composite panels were improved. The recycling process technology can be transformed to commercial scale to produce full‐size transportation flooring panels. A product pathway is established in consideration of lower cost and improved recyclability.

Vaidya, Uday↗
DOE OSTI2024

The Wind Turbine Rotors of the Future: A Research Agenda from the Big Adaptive Rotor Project

This white paper outlines a roadmap to inform future research efforts around the wind turbine rotors of the future. The document is authored by researchers that have been working on the Big Adaptive Rotor (BAR) and related initiatives at the National Renewable Energy Laboratory and Sandia National Laboratories. The Wind Energy Technologies Office of the U.S. Department of Energy has been funding BAR since 2018. The learnings from BAR have been documented in dozens of publications. This new paper identifies unresolved critical challenges in wind turbine rotor technology and structures them in four large topic areas: 1. Predictive and validated numerical tools. 2. Design methods and standards. 3. Improvements in manufacturing. 4. Technological innovations. Although wind turbines have not changed in their core architecture, with the market almost entirely dominated by three-bladed upwind rotors, a vast amount of research has allowed to introduce technological innovations resulting in a reduction in levelized cost of energy that made wind competitive with all traditional sources of electricity. Focusing on the rotor, blades will keep following the trend of mass and stiffness reduction, will adopt segmentation, and will keep growing in length, both land-based and offshore. To support this continuous innovation, this white paper argues that research efforts in rotor technology at the national labs are best directed to the first three topic areas and to low technology-readiness-levels (1-3) innovations, leaving the task of implementing higher-TRL (4-9) technological innovations to industry stakeholders. This research roadmap is also well aligned with the upcoming roadmap defined during the International Energy Agency 109th Topical Expert Meeting on the Grand Challenges of Wind Energy.

17 WIND ENERGY↗
DOE OSTI2022

2021 Prototype Manufacture and Installation Awardee: Pecos Wind Power, Inc.

Through the 2021 Competitiveness Improvement Project (CIP), Pecos Wind Power will manufacture a prototype of its 85-kilowatt (kW) horizontal-axis distributed wind turbine, the PW85, a new wind turbine that began development in 2017 when the company was founded. The PW85 wind turbine includes an industry-leading rotor diameter (30 meters) and full-span variable pitch blades to target a levelized cost of energy (LCOE) of $0.103/kilowatt-hour in low annual wind speeds (6 meters per second). This is 55% lower than the average small wind turbine project installed in 2018. The goal of this project is to spur the development of increasingly lower-cost, high-capacity-factor distributed wind turbines. As a result, Pecos Wind Power will manufacture and install wind turbines that increase the geographic area in which distributed wind power is cost competitive with retail-priced electricity and other distributed energy resources - primarily solar energy.

CIP↗