Search NASA⌕ Search

SEARCH · Search NASA

Results for “Accelerated testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Synergistic effect of polyaniline on stabilizing Pt nanoparticles in PEMFCs†

The stability of Pt nanoparticles on a carbon support is crucial for the lifespan of polymer electrolyte membrane fuel cells as well as other electrocatalysis systems such as electrolyzers. Here we took the approach of utilizing the covalently grafted polyaniline on carbon to stabilize Pt nanoparticles by simultaneously alleviating the particle migration and mitigating the Ostwald ripening, which are two major mechanisms for loss of the catalyst stability. A comprehensive investigation of the stability and performance of Pt catalyst nanoparticles on these supports reveals that the polyaniline can shift the Pt L edge binding energy and the Pt 4f peak energy, leading to the increased redox potential of the Pt nanoparticles and making them more resistant to oxidation. Interestingly, the highest polyaniline density (50 wt%) does not show the best catalyst stability, rather, the second (33 wt%) demonstrates the best catalyst stability among these catalysts. Combining the XPS, XAS and fuel cell stability studies, we concluded that the locations of the Pt nanoparticles over the polyaniline layer on the carbon surface depend on the surface density of the polyaniline over the carbon surface. The Pt nanoparticles in the 50 wt% polyaniline catalyst are wrapped by the polyaniline polymer but do not sit directly on the carbon surface, while Pt nanoparticles in the 33 wt% polyaniline catalyst sit on the carbon surface and are densely surrounded by the polyaniline polymer. The results show that the mass activity loss is 12.5% while the ECSA (electrochemically active surface area) loss is 37.1% after 30k cycles of accelerating stress test for the 33 wt% polyaniline catalyst, far exceeding the DOE 2020 target for MEA (i.e., mass activity loss < 50%, and ECSA loss < 40%). Overall, the polyaniline has a synergistic effect on mitigating the surface migration and slowing down the Ostwald ripening to stabilize the Pt nanoparticles in fuel cells. The novel strategy to stabilize Pt nanoparticles using polyaniline opens a new pathway in the development of highly stable catalysts: relying on the functionalization group on the carbon support, instead of just focusing on the catalyst itself.

Li, Chenzhao↗
DOE OSTI2014

Beam Transport Testing for the Production Accelerator Arrangement

The beam transport system is designed to deliver an electron beam from the accelerator to the target. The design of the beam line depends on beam parameter (energy, energy spread, etc.) and target geometry. Elements of the beam transport system should provide transportation, focusing, and positioning of the beam onto the target surface.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Development of Accelerated High Temperature Mechanical Testing Techniques

The Advanced Materials and Manufacturing Technologies (AMMT) Program focuses on advancing materials and manufacturing techniques for nuclear energy applications, particularly in the qualification of materials for high-temperature structural use. This report presents work on refining the creep testing of small specimen geometries. Efforts include the development of a new specimen geometry for sub-sized specimens, which were subjected to uniaxial creep tests. The results contribute to the understanding of material behavior under stress at elevated temperatures and offer potential improvements in creep data collection methods. These findings support ongoing advancements in material qualification processes essential for nuclear reactor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Ultra-High Gradient Channeling Acceleration in Nanostructures: Design/Progress of Proof-of-Concept (POC) Experiments

A short bunch of relativistic particles or a short-pulse laser perturbs the density state of conduction electrons in a solid crystal and excites wakefields along atomic lattices in a crystal. Under a coupling condition the wakes, if excited, can accelerate channeling particles with TeV/m acceleration gradients in principle since the density of charge carriers (conduction electrons) in solids n 0 = ~ 10 20 – 10 23 cm -3 is significantly higher than what can be obtained in gaseous plasma. Nanostructures have some advantages over crystals for channeling applications of high power beams. The dechanneling rate can be reduced and the beam acceptance increased by the large size of the channels. For beam-driven acceleration, a bunch length with a sufficient charge density would need to be in the range of the plasma wavelength to properly excite plasma wakefields, and channeled particle acceleration with the wakefields must occur before the ions in the lattices move beyond the restoring threshold. In the case of the excitation by short laser pulses, the dephasing length is appreciably increased with the larger channel, which enables channeled particles to gain sufficient amounts of energy. This paper describes simulation analyses on beam- and laser (X-ray)-driven accelerations in effective nanotube models obtained from Vsim and EPOCH codes. Experimental setups to detect wakefields are also outlined with accelerator facilities at Fermilab and NIU. In the FAST facility, the electron beamline was successfully commissioned at 50 MeV and it is being upgraded toward higher energies for electron accelerator R&D. The 50 MeV injector beamline of the facility is used for X-ray crystal-channeling radiation with a diamond target. It has been proposed to utilize the same diamond crystal for a channeling acceleration POC test. Another POC experiment is also designed for the NIU accelerator lab with time-resolved electron diffraction. Recently, a stable generation of single-cycle laser pulses with tens of Petawatt power based on thin film compression (TFC) technique has been investigated for target normal sheath acceleration (TNSA) and radiation pressure acceleration (RPA). The experimental plan with a nanometer foil is discussed with an available test facility such as Extreme Light Infrastructure – Nuclear Physics (ELI-NP).

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Fabrication and accelerated long-term stability test of asymmetrical hollow fiber-supported thin film oxygen separation membrane

Asymmetrical hollow fiber-supported thin film membrane may provide microstructural advantages for air separation and oxygen production. The fabrication of such a membrane is usually very difficult, particularly the sintering behaviors and thermal expansion coefficient (TEC) mismatch among multiple layers. This directly affects the reliability and long-term stability of the membrane. Here, in this research, the sintering behaviors of a set of simple oxides are systematically studied and ZnO is identified as a material component for composite substrate La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF)-ZnO. The LSCF-ZnO ratios are further optimized by trading off several factors, e.g., matching the sintering behaviors and TECs of the LSCF-ZnO composite with those of LSCF thin film separation layer while enhancing the substrate strength. With the identified LSCF-ZnO ratio, the LSCF-ZnO composite hollow fiber substrate precursor is formed through slurry spinning process with porous microstructure being formed via phase inversion process. The thin film LSCF dense separation layer is then dip-coated on the substrate followed by co-sintering process. A thin, porous PrBaCo(Fe 0.6 Zr 0.2 Y 0.2 )O 5+δ (PBCFZY) catalyst layer is fabricated on the dense LSCF separation layer with dip-coating and sintering process, forming an asymmetrical membrane device LSCF-ZnO/LSCF/PBCFZY. Oxygen permeation test of the device is systematically conducted, and the fundamental mechanisms are analyzed. An accelerated long-term stability test of the membrane is also conducted (~550h, 46 thermal cycling loads), demonstrating excellent robustness and durability. The device is characterized and analyzed before and after the test. By replacing a considerable amount of high cost LSCF with low cost ZnO in the substrate, it not only enhances the stability but also reduces the capital cost of the membrane for practical applications.

42 ENGINEERING↗
DOE OSTI2022

Investigating the Particle Growth in Bimodal Pt/C Catalysts by In-Situ Small-Angle X-ray Scattering: Challenges in the Evaluation of Stress Test Protocol-Dependent Degradation Mechanisms

The influence of different combinations of accelerated stress test (AST) protocols simulating load-cycle and start/stop conditions of a proton exchange membrane fuel cell (PEMFC) vehicle is investigated on a bimodal Pt/C catalyst. The bimodal Pt/C catalyst, prepared by mixing two commercial catalysts, serves as a model system and consists of two distinguishable size populations. The change in mean particle size was investigated by in situ small-angle X-ray scattering (SAXS). The comparison to the reference catalysts, i.e., the two single-size population catalysts, uncovers the presence of electrochemical Ostwald ripening as a degradation mechanism in the bimodal catalyst. Increasing the harshness of the applied AST protocol combinations by faster changing between load-cycle or start/stop conditions, the particle size of the larger population of the bimodal catalyst increases faster than expected. Surprisingly, the change in mean particle size of the smaller size population indicates a smaller increase for harsher AST protocols, which might be explained by a substantial electrochemical Ostwald ripening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

PACT Perovskite PV Module Stress Testing Protocol (Version 0.0)

The purpose of this protocol is to use accelerated stress testing to assess the durability of metal halide perovskite (MHP) photovoltaic (PV) modules. The protocol aims to apply field relevant stressors to packaged MHP modules to screen for early failures that may be observed in the field. The current protocol has been designed with a glass/glass-PIB edge seal, no encapsulant package in mind. PACT anticipates adding additional testing sequences to evaluate additional stressors (e.g., PID, reverse bias) in the future.

42 ENGINEERING↗
DOE OSTI2024

Fabrication and testing of the transition section between modules of a wakefield accelerator

The fabrication process is presented for a typical transition section located between each cylindrical corrugated waveguide structure comprising the wakefield accelerator module. The transition section includes couplers for extracting the 180 GHz TM 01 accelerating mode and separate couplers for extracting the 190 GHz HE 11 dipole mode, both modes induced by the electron bunch traversing the cylindrical corrugated waveguide structure. Extraction of the high-power accelerating mode reduces the heat load due to the subterahertz wave power dissipation within the corrugated accelerating structure. Extraction of the low-power dipole mode serves the purpose of detecting the electron bunch transverse oscillations within the wakefield accelerator and identifying the onset of beam breakup instability. Comprehensive testing of the fully functional transition section with an electron beam was done at the Accelerator Test Facility in Brookhaven National Laboratory which verified the functionality of the transition section. Published by the American Physical Society 2024

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Evaluation of Irradiation Creep Effects in HT9 Cladding for FAST Experiments

The push for advanced reactor fuels for improved reactor safety and efficiency had led to a renewed interest in metallic fuel for nuclear reactor applications. Experimental investigation is necessary to ensure a robust understanding of the thermomechanical properties of new metallic fuel designs. Unfortunately, with the current experimental facilities, thoroughly investigating the responses of metallic fuel burnup would take a prohibitively long time. To alleviate this, the Fission Accelerated Steady State Test (FAST) was developed to accelerate the irradiation testing while simultaneously decreasing the sensitivity to fabrication tolerances by reducing the fuel diameter and scaling the experiment. This method successfully scales the radiation effects on the fuel, but the HT9 cladding is not exposed to prototypic radiation conditions. This raises questions on whether the FAST experiment results are truly indicative of the HT9 cladding performance due to radiation induced creep effects not being appropriately accounted for. Using BISON fuel performance code, the simulated FAST cladding strain is compared to simulated EBR-II cladding strain. This is done through a sensitivity study of input parameters and scaling of neutron fluence on the cladding. This allows a parametric comparison of physical phenomena on the effective difference between cladding strains between FAST and equivalent burnup EBR-II fuel pins. The results show that the irradiation induced deformation (creep or swelling) is insignificant compared to the thermal-mechanical deformation. Therefore, the difference between the FAST experiment cladding and the EBR-II experiment cladding is negligible and comparison of fuel system performance between the two experiments is appropriate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Optimization of Fatigue Test Signal Compression Using the Wavelet Transform (Final Report)

This report summarizes Sandia National Laboratories (SNL) contribution to ATA Engineering, Inc's (ATA) project for the Naval Air Systems Command (NAVAIR), entitled "Optimization of Fatigue Test Signal Compression Using the Wavelet Transform." Sandia National Laboratories were a subcontractor to ATA. We were involved because this was a Small Business Technology Transfer (STTR) project that required ATA to partner with a national laboratory or academic institution. ATA selected SNL, and specifically the Environments Engineering Department (1557) because ATA has a long-standing working relationship with this department and the department staff have experience in environment definition, signal processing, fatigue testing protocols and traditional methods of generating inputs for accelerated fatigue testing.

42 ENGINEERING↗
DOE OSTI2018

The Effect of Aging on the Delamination Fracture Energy of Glass Solar Reflectors

Thin metal and metal oxide films deposited on glass or polymer substrates have been widely applied to manufacture front surfaced solar reflectors such as those used in the concentrated solar power (CSP) systems due to the facts that they are highly transparent, resistant to ultraviolet (UV) light and abrasion, and chemically inert. However, the reliable operation over long periods of outdoor exposure of such solar reflectors depends on the adequate adhesion between each layer to prevent delamination and subsequent failure. We report results from measurements of the delamination fracture energy (DFE) of the weakest interface in both as-deposited and aged reflectors, where the reflector construction consists of a glass/copper/silver/oxide stack. In this study, DFE was measured using a width-tapered beam method and the test results showed that the weakest interface of this solar reflector is the copper-glass interface, with a delamination fracture energy of approximately 4.4 J/m 2 . In order to verify the test results, finite element (FE) simulations were run using the commercial software package ABAQUS 6.14 based on the cohesive zone model (CZM). In the simulations, the DFE derived from the delamination measurement was treated as an input and the delamination forces from the FE simulations were compared to the experimental results. The good agreement between the tested and simulated delamination force indicated that this width-tapered beam method is accurate even for very small DFE, making it appropriate to test the DFE of front surfaced glass solar reflectors. Additionally, in order to study the aging effect on the DFE, accelerated aging tests were conducted using samples with different protective coatings, one group of samples with alumina ( Al 2 O 3 ) protective coating and the other group with titania ( TiO 2 ) protective coating. The DFE after 50 and 100 hours of accelerated aging were measured. The test results showed that the copper-glass interface would still be the weakest interface for all samples after aging, and the DFE for samples with Al 2 O 3 protective coating was unchanged whereas the copper-glass interface was found to undergo statistically significant change after both 50 and 100 hours of aging for samples with TiO 2 protective coating. We found that DFE at the copper/glass interface decreased after 50 hours of aging then increased after 100 hours of aging. The origin of this non-monotonic response of TiO 2 coated reflectors under accelerated aging conditions is unknown.

36 MATERIALS SCIENCE↗