Search NASA⌕ Search

SEARCH · Search NASA

Results for “Building Structural Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Control System Development for A Zero Boil-Off Hydrogen Storage Demonstration With Two-Stage Active Cooling

A NASA team is designing and building a test article to demonstrate the long duration storage of liquid hydrogen via active cooling (cryocoolers) while implementing a two-stage cooling approach. This activity is one of a large portfolio of NASA’s Space Technology Mission Directorate funded activities which focuses on the technology maturation needed for long duration storage of cryogenic liquid in-space. The current state-of-the-art for liquid hydrogen storage on-orbit is on the order of hours while NASA’s planned missions require storage for months, or even years. To enable such a long duration, Zero Boil-Off conditions must be achieved which requires passive technologies to minimize environmental heat loads, but also active cooling to intercept and reject the remaining heat to deep space. The implementation of active cooling results in a significant amount of dry mass added to the vehicle. Utilizing a Two-Stage Cooling approach, analysis and testing to date indicates the Zero Boil-Off of liquid hydrogen can be achieved with less mass and electrical power relative to a single-stage cooling approach where only one cryocooler is used. This activity will demonstrate the fully integrated suite of technologies needed to enable the Two-Stage Cooling approach which includes Multi-Layer Insulation blankets, Low Conductivity Structures, a Tube-On-Tank Heat Exchanger, Tube-On-Shield Heat Exchanger and a Two-Stage Cryogenerator (both 90 Kelvin and 20 Kelvin) with each stage having an independently controlled circulation loop. The bulk of the heat load is intercepted by the 90 Kelvin loop via a thin foil heat exchanger internal to the insulation blankets (also known as a Broad Area Cooling Shield), with the remainder removed at cryofluid temperature (20 Kelvin) by tubes directly welded to the outer tank surface. In this paper, we examine the challenges of controlling the system, and describe the development of control algorithms and software for future testing with liquid hydrogen. The interactions between the cryofans which control circulation loop mass flow rates, electrical heaters which vary the cryocooler lift to simulate the operation of variable-lift flight units, tank heaters which can vary the overall heat load, and the effects of changes in circulation loop pressure as temperatures change, can be complex and must be well understood to maintain steady-state propellant conditions and achieve Zero Boil-Off. Parallel PID loops and watchdog programs implemented on the user interface system will help bring the systems to steady state operation and keep them at selected operating points within acceptable error, while avoiding runaway feedback loops.

cryogenics↗

NASA ACC High Energy Dynamic Impact Methodology and Outcomes

For High Energy Dynamic Impact (HEDI) events, testing to evaluate the structural response of primary aircraft structure for design and certification is both expensive and time consuming. This paper discusses current work seeking to assess, develop, and validate appropriate analytical models that accurately predict physical response, damage, and failure modes for large scale composite structures in HEDI events. Four state-of-the-art Progressive Damage Analysis (PDA) methods were employed for this phased project: LS-DYNA MAT162, LS-DYNA MAT261, Smoothed Particle Galerkin (SPG), and EMU Peridynamics. Multiple material systems were considered, namely T700/5208 textile-infusion triaxial braid, T800/AMD-825 textile-infusion triaxial braid, IM7/8552 uni-directional tape, and SPG 196-PW/8552 plain-weave fabric. Extensive ballistic impact testing was performed to support this activity and measured results were compared to predictive models for assessment using panel delamination, panel displacement, force at the load cells, and threshold velocity as measures. Ultimately, the work under this activity provided significant progress in advancing the state-of-the-art in the use of PDA for HEDI events. Each material model had favorable performance comparing to test in some parameters and needed improvement in others. With the lessons learned from this activity, significant progress was made in the ability to predict panel behavior for a more general case beyond the flat panel in a ballistic impact event. Subsequent Phase II of the NASA ACC HEDI effort will continue to build on the coupon testing, flat panel ballistic impact testing, and analysis performed to-date with application of the PDA methods for intended material selections to test articles with greater complexity of configuration, curvature, and scale. It is not the intention of this paper to present a full set of data, but rather to give an overview of the NASA HEDI effort and show a small representative subset of the test and analysis results.

Hunziker, Kenneth J.↗

Space Resource Utilization and Extending Human Presence Across the Solar System

The Presidents Vision for Exploration is not a single mission, but an open ended journey that seeks to answer "How can we live on other worlds?" Using space resources is the only known approach for affordable, sustained, flexible, and self sufficient, human occupation beyond Earth orbit. Earth is a large planet. A simple analysis using the rocket equation shows that if Earth were a bit larger, chemical propulsion as a mechanism to access space would become impractical. Thus, even with the most efficient chemical rocket launch capability, the cost of lifting massive payloads into space will remain very steep (currently about $l00k/lb to the Moon and greater than $500k/lb to Mars). Space resource utilization should begin with an aggressive broad based demonstration program as afforded by the precursor missions implementation of the President's Vision of Exploration. Ion engine upper stages, for example, were studied for over 30 years, but only implemented in design after the Deep Space 1 in space demonstration. These demonstrations should include: extraction of elements from lunar regolith, and Martian soil and atmosphere, demonstration of power break even and growth from lunar or Mars moons derived photovoltaics, oxygen extraction for life support and propellant, and metals and alloys for in space repair and the production of habits and radiation shielding. Space resource utilization yields operational dividends through the subsequent programs including: propellant from lunar oxygen which could cut transportation costs from Earth in half, mega watts per year of power grown from lunar photovoltaics at decreasing cost per kW, decreased cost for human Mars missions by a factor of 10 by using propellant derived from Mars atmosphere for return, and in space manufacturing and food production with space resources yielding safe sustained and eventually self sufficient human presence in space. After the demonstration and implementation, the space resource utilization investment enables commercial and private viability beyond Earth orbit. For example, analysis has shown the lunar oxygen production for propellant becomes commercially viable after the exploration program completes the R&D, and power from lunar derived photovoltaics could, according to past NASA sponsored studies, pay for themselves while supplying most of Earth's electrical energy after about 17 years. Besides the Moon and Mars the resources of the near Earth asteroids enable the building of large space structures and science payloads. Analysis has shown that one of the thousands of these objects (some as easily accessible in space as the Moon and Mars), 2 km dia, the size of a typical open pit mine, would cost the total global financial product of Earth for 30,000 years if we were to launch it from Earth. Beyond Mars, the belt asteroids have been calculated to contain enough materials for habitat and life to support 10 quadrillion people. Thus, the development and use of space resources enables the extension of human life through the solar system allowing humanity to move from a planetary to a solar system society.

Curreri, Peter A.↗

LISA Technology Development and Risk Reduction at NASA

The Laser Interferometer Space Antenna (LISA) is a joint ESA-NASA project to design, build and operate a space-based gravitational wave detector based on a laser interferometer. LISA relies on several technologies that are either new to spaceflight or must perform at levels not previously demonstrated in a spaceflight environment. The ESA-led LISA Pathfinder mission is the main effort to demonstrate LISA technology. NASA also supports complementary ground-based technology development and risk reduction activities. This presentation will report the status of NASA work on micronewton thrusters, the telescope, the optical pointing subsystem and mission formulation. More details on some of these topics will be given in posters. Other talks and posters will describe NASA-supported work on the laser subsystem, the phasemeter, and aspects of the interferometry. Two flight-qualified clusters of four colloid micronewton thrusters, each capable of thrust Levels between 5 and 30 microNewton with a resolution less than 0.l microNewton and a thrust noise less than 0.1 microNewton/vHz (0.001 to 4 Hz), have been integrated onto the LISA Pathfinder spacecraft. The complementary ground-based development focuses on lifetime demonstration. Laboratory verification of failure models and accelerated life tests are just getting started. LISA needs a 40 cm diameter, afocal telescope for beam expansion/reduction that maintains an optical pathlength stability of approximately 1 pm/vHz in an extremely stable thermal environment. A mechanical prototype of a silicon carbide primary-secondary structure has been fabricated for stability testing. Two optical assemblies must point at different distant spacecraft with nanoradian accuracy over approximately 1 degree annual variation in the angle between the distant spacecraft. A candidate piezo-inchworm actuator is being tested in a suitable testbed. In addition to technology development, NASA has carried out several studies in support of the mission formulation. The results of systems engineering work on flight software, avionics and reliability will be summarized.

Stebbins, Robin T.↗

Ares I and Ares V First Stage - Powering Exploration

The National Aeronautics and Space Administration (NASA) Ares Projects Office (APO) is continuing to make progress toward the final design of the first stage propulsion system for the Ares I crew launch vehicle and the Ares V cargo launch vehicle. Ares I and Ares V will provide the space launch capabilities needed to fulfill NASA' s exploration strategy of sending human beings to the Moon, Mars, and beyond. As primary propulsion for the Ares launch vehicles, the Space Shuttle-derived Reusable Solid Rocket Motor (RSRM) is one of the first and most important components to be tested. The first flight of Ares I, called Ares I-X, will occur in April 2009, with booster integration to begin at Kennedy Space Center (KSC) by autumn 2008. The Ares I-X flight will use a combination of flight and simulation hardware to obtain data on controlling the long and narrow crew launch vehicle configuration. The test will use a four-segment RSRM from the Shuttle inventory and a fifth spacer segment to simulate the size and weight of the operational five-segment motor to be used on later flights. The upper stage, Orion crew exploration vehicle, and launch abort system will all be replaced with simulator hardware. Manufacturing work has begun on the spacer segment, as well as the new forward hardware for the booster. Atlas V avionics will be adapted to control Ares I-X' s first stage. That hardware is undergoing hardware-in-the-loop testing in a contractor-provided systems integration laboratory (SIL); a critical design review (CDR) was completed in December 2007. Drogue and main parachute drop tests have also been conducted successfully at Yuma Proving Grounds, allowing the First Stage team to begin fabricating parachutes for Ares I-X. The Ares I-X flight test will be the first flight test for the parachutes. A series of preliminary design technical interchange meetings is being conducted prior to the Ares I-X CDR in January 2007 to ensure readiness for the flight. Much of the First Stage activity in 2007 has focused on a series of preliminary design (PDR) activities associated with each booster subsystem. These events will culminate in a formal preliminary design review in 2008, where subsystems and component specifications will be developed and associated analyses and drawings will be evaluated for technical adequacy. The first stage also has been undergoing a series of trade studies to determine means for upgrading booster performance and reducing operational costs. Performance improvement studies have included changing from polybutadiene acrylonitrile (PBAN) propellant to hydroxyl-terminated polybutadiene (HTPB); replacing aluminum with composite motor casings; and optimizing or upgrading the propellant grain and nozzle structures. Some or all of these changes could result in a block upgrade to the Ares I first stage, after becoming the standard configuration for the Ares V. The cost reduction studies included a change from reusable or recoverable boosters to completely expendable boosters; changing from hydrazine-powered to more environmentally friendly electrohydrostatic actuators (EHAs) on the thrust vector control (TVC) system; and changing the location of the separation plane to reduce the likelihood of recontact upon booster separation. The expendability trade study resulted in a decision to keep the recoverable boosters, as the new hardware costs significantly outweighed the potential operational cost savings due to reduced ground operations. Likewise, due to cost considerations, the team continued using existing hydrazine-powered actuators for the TVC system. The separation plane location for Ares I is still being studied, with results to be announced in 2008. In short, the Ares launch vehicles' first stage is building upon NASA's close familiarity with this Shuttle-derived system, while continuing to seek out improvements for long-term exploration.

Priskos, Alex S.↗

Mars 2020 Thermal Protection Systems Sizing and Development

The Mars 2020 spacecraft delivering the Perseverance Rover to Mars was planned to be a build-to-print repeat of the Mars Science Laboratory (MSL) spacecraft that delivered the Curiosity Rover to Mars in 2012. The 2020 mission would deliver a slightly higher mass at a lower entry velocity, so the mission designers were comfortable with the cost saving approach of using an already proven design. The approach used in sizing the thermal protection systems (TPS) for the various components of the MSL spacecraft included convective heating and shock layer radiation (a small contributor) on the heatshield and only convective heating on all of the aft body parts. At the time, it was assumed that the contribution of radiation from the shock layer and the wake was negligible on the aft body at Mars. In the time since the MSL spacecraft was designed, in light of new data and analysis, NASA realized the significance of radiative heating in the aftbody on vehicles entering Mars, beginning with the InSight entry. New analyses showed that the radiant heat fluxes on aft body components at Mars were of the same order or even larger than predicted convective heat fluxes. The Mars 2020 team was tasked with showing that the TPS thicknesses designed for MSL with only convective heating would survive the Mars 2020 convective plus radiative heat flux environments. Luckily, many of the MSL aft body components were sized using an extra conservative approach, often sizing for the worst environment at the lightest, thinnest structure, even though the environments and structures were not co-located. The Mars 2020 team had to more accurately evaluate the environments and structures to show that the design would close

Mars Entry↗

Parametric Flutter Analysis of the TCA Configuration and Recommendation for FFM Design and Scaling

The current HSR Aeroelasticity plan to design, build, and test a full span, free flying transonic flutter model in the TDT has many technical obstacles that must be overcome for a successful program. One technical obstacle is the determination of a suitable configuration and point in the sky to use in setting the scaling point for the ASE models program. Determining this configuration and point in the sky requires balancing several conflicting requirements, including model buildability, tunnel test safety, and the ability of the model to represent the flutter mechanisms of interest. As will be discussed in detail in subsequent sections, the current TCA design exhibits several flutter mechanisms of interest. It has been decided that the ASE models program will focus on the low frequency symmetric flutter mechanism, and will make no attempt to investigate high frequency flutter mechanisms. There are several reasons for this choice. First, it is believed that the high frequency flutter mechanisms are similar in nature to classical wing bending/torsion flutter, and therefore there is more confidence that this mechanism can be predicted using current techniques. The low frequency mode, on the other hand, is a highly coupled mechanism involving wing, body, tail, and engine motion which may be very difficult to predict. Second, the high frequency flutter modes result in very small weight penalties (several hundred pounds), while suppression of the low frequency mechanism inside the flight envelope causes thousands of pounds to be added to the structure. In order to successfully test the low frequency flutter mode of interest, a suitable starting configuration and point in the sky must be identified. The configuration and point in the sky must result in a wind tunnel model that (1) represents the low-frequency wing/body/engine/empennage flutter mechanisms that are unique to HSCT configurations, (2) flutters at an acceptably low frequency in the tunnel, (3) flutters at an acceptably low dynamic pressure in the tunnel, (4) allows sufficient weight for model buildability without inordinately high cost, and (5) has significant separation between the target flutter mechanism and other, potentially catastrophic, flutter mechanisms.

Baker, Myles↗

Gemini results as related to the Apollo program

The Gemini Program was conceived to provide a space system that could furnish answers to many of the problems in operating manned vehicles in space. It was designed to build upon the experience gained from Project Mercury, and to extend and expand this fund of experience in support of the manned lunar landing program and other future manned space-flight programs. The purpose of this paper is to relate some of the results of the Gemini Program to the Apollo Program, and to discuss some of the contributions which have been made. The objectives of the Gemini Program applicable to Apollo are : (1) long-duration flight, (2) rendezvous and docking, (3) post-docking maneuver capability, (4) controlled reentry and landing, (5) flight- and groundcrew proficiency, and (6) extra vehicular capability. The achievement of these objectives has provided operational experience and confirmed much of the technology which will be utilized in future manned programs. These contributions will be discussed in three major areas : launch and flight operations, flight-crew operations and training, and technological development of subsystems and components. While there is obvious interrelation among the three elements, the grouping affords emphasis and order to the discussion.

structural integrity↗

The Biological Flight Research Facility

NASA Ames Research Center (ARC) is building a research facility, the Biological Flight Research Facility (BFRF), to meet the needs of life scientists to study the long-term effects of variable gravity on living systems. The facility will be housed on Space Station Freedom and is anticipated to operate for the lifetime of the station, approximately thirty years. It will allow plant and animal biologists to study the role of gravity, or its absence, at varying gravity intensities for varying periods of time and with various organisms. The principal difference between current Spacelab missions and those on Space Station Freedom, other than length of mission, will be the capability to perform on-orbit science procedures and the capability to simulate earth gravity. Initially the facility will house plants and rodents in habitats which can be maintained at microgravity or can be placed on a 2.5 meter diameter centrifuge. However, the facility is also being designed to accommodate future habitats for small primates, avian, and aquatic specimens. The centrifuge will provide 1 g for controls and will also be able to provide gravity from 0.01 to 2.0 g for threshold gravity studies as well as hypergravity studies. Included in the facility are a service unit for providing clean chambers for the specimens and a glovebox for manipulating the plant and animal specimens and for performing experimental protocols. The BFRF will provide the means to conduct basic experiments to gain an understanding of the effects of microgravity on the structure and function of plants and animals, as well as investigate the role of gravity as a potential countermeasure for the physiological changes observed in microgravity.

Johnson, Catherine C.↗

Understanding Workforce Agility at NASA Kennedy Space Center

NASA leads the world in space research and provides other government agencies, educational institutions, and companies opportunities to explore, launch, and conduct research in and around space. NASA has 11 formal locations based around the United States, and each has different goals and objectives to help NASA meet its overall mission. 2004, President George Bush announced a new vision for the Space Exploration program. During his grand announcement, he discussed that the Space Shuttles would retire due to the 2003 Space Shuttle Columbia accident, where the crew and the space vehicle were lost. The Kennedy Space Center (KSC) would no longer manage the day-to-day operations of maintaining the US Space Shuttle fleet. Our NASA teams would continue working to finish the Space Shuttle program's mission to build the International Space Station. Afterward, NASA would transition to develop and test a new spacecraft, the Crew Exploration Vehicle. The third goal was to return to the moon by 2020 as the launching point for missions beyond, to get humans from lower Earth orbit to the moon and Mars. (Secretary, 2004) The KSC engineering workforce had to prepare to transition from Operational support of the Space Shuttle program to the design and development of over 50 subsystems for the future SLS and Orion Launch Systems at the Kennedy Space Center. These subsystems developed at the Kennedy Space Center Engineering Directorate followed a comprehensive design process that required several different product deliverables during various phases for each subsystem. (Schafer et al., 2013) What allowed these systems to be successful? What enabled NASA KSC to complete over 130 Artemis 1 Design Certification and System Acceptance Reviews, closing over 21,656 Requirements to deem the Artemis 1 rocket ready for launch? Little is known about the NASA engineering workforce agility characteristics that enabled the organization to transition from the Space Shuttle program that ended in 2011 and launch the Artemis Program's SLS rocket on November 16, 2022.

Workforce Agility↗

Validation of an Accurate Three-Dimensional Helical Slow-Wave Circuit Model

The helical slow-wave circuit embodies a helical coil of rectangular tape supported in a metal barrel by dielectric support rods. Although the helix slow-wave circuit remains the mainstay of the traveling-wave tube (TWT) industry because of its exceptionally wide bandwidth, a full helical circuit, without significant dimensional approximations, has not been successfully modeled until now. Numerous attempts have been made to analyze the helical slow-wave circuit so that the performance could be accurately predicted without actually building it, but because of its complex geometry, many geometrical approximations became necessary rendering the previous models inaccurate. In the course of this research it has been demonstrated that using the simulation code, MAFIA, the helical structure can be modeled with actual tape width and thickness, dielectric support rod geometry and materials. To demonstrate the accuracy of the MAFIA model, the cold-test parameters including dispersion, on-axis interaction impedance and attenuation have been calculated for several helical TWT slow-wave circuits with a variety of support rod geometries including rectangular and T-shaped rods, as well as various support rod materials including isotropic, anisotropic and partially metal coated dielectrics. Compared with experimentally measured results, the agreement is excellent. With the accuracy of the MAFIA helical model validated, the code was used to investigate several conventional geometric approximations in an attempt to obtain the most computationally efficient model. Several simplifications were made to a standard model including replacing the helical tape with filaments, and replacing rectangular support rods with shapes conforming to the cylindrical coordinate system with effective permittivity. The approximate models are compared with the standard model in terms of cold-test characteristics and computational time. The model was also used to determine the sensitivity of various circuit parameters including typical manufacturing dimensional tolerances and support rod permittivity. By varying the circuit parameters of an accurate model using MAFIA, these sensitivities can be computed for manufacturing concerns, and design optimization previous to fabrication, thus eliminating the need for costly experimental iterations. Several variations were made to a standard helical circuit using MAFIA to investigate the effect that variations on helical tape and support rod width, metallized loading height and support rod permittivity, have on TWT cold-test characteristics.

Kory, Carol L.↗

Magnetic Reconnection: Theoretical and Observational Perspectives: Preface

Magnetic reconnection is a fundamental plasma-physical process by which energy stored in a magnetic field is converted, often explosively, into heat and the kinetic energy of the charged particles that constitute the plasma. It occurs in a variety of astrophysical settings, ranging from the solar corona to pulsar magnetospheres and winds, as well as in laboratory fusion experiments, where it is responsible for sawtooth crashes. First proposed by R.G. Giovanelli in the late I 940s as the mechanism responsible for solar flares, magnetic reconnection was invoked at the beginning of the space age to explain not just solar flares but also the transfer of energy, mass, and momentum from the solar wind to Earth's magnetosphere and the subsequent storage and release of the transferred energy in the magnetotai\. During the half century or so that has followed the seminal theoretical works by J.W. Dungey, P.A. Sweet, E.N. Parker, and H.E. Petschek, in-situ measurements by Earth-orbiting satellites and remote-sensing observations of the solar corona have provided a growing body of evidence for the occurrence of reconnection at the Sun, in the solar wind, and in the near-Earth space environment. The last thirty years have also seen the development of laboratory reconnection experiments at a number of institutions. In parallel with the efforts of experimentalists in both space and laboratory plasma physics, theorists have investigated, analytically and with the help of increasingly powerful MHD, hybrid, and kinetic numerical simulations, the structure of the diffusion region, the factors controlling the rate, onset, and cessation of reconnection, and the detailed physics that enables the demagnetization of the ions and electrons and the topological reconfiguration of the magnetic field. Moreover, the scope of theoretical reconnection studies has been extended well beyond solar system and laboratory plasmas to include more exotic astrophysical plasma systems whose strong (10(exp 14)-10(exp 15) G) magnetic fields require that models of reconnection in these systems incorporate quantum electrodynamical, special relativistic, and radiative effects. The papers collected in this topical issue of Space Science Reviews cover different aspects of recent theoretical and observational work on magnetic reconnection in solar and space physics, astrophysics, and laboratory plasma physics. They derive from presentations given at a workshop on magnetic reconnection held in the Yosemite National Park, February 8-12,2010. The intent of the workshop was to stimulate, through a combination of tutorial talks, shorter focused talks, and extensive informal discussions, an interdisciplinary dialogue among members of the different research communities working on the problem of magnetic reconnection. One of the motivating considerations for holding the workshop was its relevance to NASA's Magnetospheric Multiscale (MMS) mission, scheduled for launch in 2014. The four identically instrumented MMS spacecraft are designed to study reconnect ion in Earth's magnetosphere and, specifically, to probe the electron diffusion region in order to determine the microphysical processes that enable the change in the topology of the magnetic field. Building on the achievements of the multi spacecraft Cluster and THEMIS missions, MMS will use the magnetosphere as an astrophysical plasma laboratory in which to test, through in-situ measurement of the plasma, energetic particles, and electric and magnetic fields, various models and theories that have emerged during the past twenty years, a period of extraordinarily productive theoretical and observational work.

Lewis, W. S.↗

Experimental Demonstration and System Analysis for Plasmonic Force Propulsion

This project developed a higher-fidelity model of a recently envisioned small spacecraft propulsion system for precision pointing and proximity control. Plasmonic force propulsion harnesses solar light focused onto plasmon reactive subwavelength nanostructures to accelerate and expel nanoparticle propellant via strong optical forces. The goal of the project was to show that plasmonic space propulsion can provide the level of proximity and attitude control envisioned for future NASA nano/picosatellite missions, a level that is better than state-of-the-art approaches. We achieved this goal by showing that plasmonic force thrusters are feasible for a range of advanced mission concepts requiring swarm formations in a deep space environment. We performed three case studies that evaluated the performance of the plasmonic force propulsion thruster in a deep space, microsatellite swarm formation. These case studies assumed the propulsion system could generate thrust at the level predicted from our Phase 1 study (1.6 μN). Through these cases we were able to analyze the concept within a mission specific context through detailed orbital dynamics calculations. Results indicate that, with the Phase 1 estimated thrust level, the approach is promising for providing attitude control to swarm formation spacecraft. Further, we achieved goals related to technology development. Specifically, we experimentally demonstrated nanoparticle acceleration due to plasmonic forces with asymmetric nanostructures excited by focused laser light. Additionally, we investigated the thrust sensitivity and nanoparticle propellant injection dependencies upon thermal effects. As a result of our study, plasmonic force propulsion is at an early TRL 3. Active research and design has been conducted analytically and in the laboratory. Furthermore, practical applications such as the three case studies have been identified for the scientific basic principles that were observed. Future efforts related to fundamental understanding of these techniques should focus on 1) developing a standalone array of asymmetric nanostructures that can effectively interact with a stream or reservoir of particles or 2) experimentally evaluate a dielectrophoretic injector for nanoparticle propellant. The main limitation discovered about plasmonic propulsion regards performance estimates significantly below the Phase 1 estimations. Specifically, original assumptions in the Phase 1 project (notably, a linear array of asymmetric nanostructures) is not a viable approach to achieving significant acceleration, high exhaust velocity, of nanoparticles. More specifically, we assumed in Phase 1 that nanoparticles would be accelerated in series by a long linear array of asymmetric nanostructures. That is, the acceleration of the nanoparticle would build and increase with the kick received by each subsequent nanostructure. This is fundamentally flawed. The potential profile of a single nanostructure is such that it prohibits this phenomenon. The potential energy associated with the plasmon-generated dielectrophoretic force is a potential well, which is good for trapping nanoparticles, but cannot provide significant acceleration of particles to expel them out and away from the nanostructure. Further, a nanoparticle expelled from the first nanostructure would need to overcome the potential barrier for entry into the next nanostructure accelerating stage. Fundamentally, this effect means that a linear array of nanostructures is not a viable accelerating structure. Correspondingly then, acceleration can, or should, only be provided by one nanostructure, and the net acceleration and thrust force of a single nanostructure is small (~cm/s exhaust velocities, sub-nN level thrust vs. the 100’s m/s, μN originally envisioned). While our experiments demonstrated acceleration and manipulation of a nanoparticle using laser light in aqueous environment, the achievable energy and momentum addition to the nanoparticle from a single nanostructure stage is too low for useful propulsion. In terms of thrust prediction, the estimated thrust of 1.6 μN in Phase 1 is reduced to a few nN of thrust with this new insight and understanding of the concept. This thrust level is too small to achieve attitude control of swarms as originally envisioned.

Plasmonic Force↗

Building a standardized Observing System Simulation Experiment (OSSE) framework for Mars

We advocate that the Decadal Survey recommends the NASA Science Mission Directorate to develop a rigorous Observing System Simulation Experiment (OSSE) framework for Mars, to optimize future atmospheric observations. Atmospheric conditions on Mars are a potential hazard source for landing missions. Errors in the estimates of atmospheric density profiles, inadequate knowledge of wind vertical structure and dust concentration as a function of height are likely causes of uncertainty at the landing site on the order of kilometers. An operational real-time weather forecasting capability for Mars would reduce such uncertainties, carrying enormous benefits to future robotic missions, and would be an invaluable prerequisite for human missions.A real-time forecasting capability relies upon three fundamental components: a critical mass of observing systems, a data assimilation system (DAS), and a global forecast model. The DAS allows the model to ingest the data effectively, optimizing the observational information content,and transforming them into a gridded representation of the atmosphere at a given time, called an ‘analysis’. The analysis is the best estimate of the atmospheric state for that time, and also represents a set of ‘initial conditions’ from which a global model can be initialized, to predict a future state of the atmosphere. The connection between analysis and forecast represents the foundation of modern weather forecasting. However, from the point of view of a forecast system,not all observations are equally impactful, partially because of the problem of “observational error correlation”, one important research topic in data assimilation development. For the Earth, partly due to the spontaneous and deregulated development of observations and forecast capabilities worldwide for more than half a century,the use of observations in contemporary operational forecast systems is suboptimal, with many potentially useful data being underutilized. On the contrary, Mars atmospheric scientists are in the unique situation of designing the next-generation observing systems by learning from the experience gathered on the Earth, so as to assure that the future instruments are specifically optimized to give the maximum benefit to a future weather forecast capability.An immensely powerful tool that has been firmly established by atmospheric scientists on the Earth is represented by a properly designed OSSE framework. A realistic OSSE framework cannot only quantify the benefit of future data types, be them surface based or space borne, but can also help design and optimize an entire observational network. Furthermore, OSSEs can provide deep insights into an atmosphere’s behavior, by addressing conceptual problems of its intrinsic predictability and delineating the regions or features of the atmosphere which are more sensitive to additional data and would benefit from a denser sampling. The difficulties posed by OSSEs are fundamentally different for Earth and Mars. For Earth, the enormous data volume imposes a tremendous constraint on any innovation in the observing systems: it is very hard for a single sensor to impact the skill. For Mars, the problem is the opposite: almost any additional instrument will exert some impact. However, OSSEs can help to evaluate the cost/benefit for every sensor and suggest optimal data configuration and density.The purpose of this white paper is to provide an introduction to a rigorously designed OSSE framework, explain the underlying problems and challenges, and engage the Mars community to collaborate with Earth Atmospheric scientists in order to develop a joint-OSSE framework for Mars with the largest consensual basis possible. An OSSE infrastructure would increase the understanding of the Martian atmosphere, would help NASA to optimize instrument specifications and orbit choice, providing the maximium benefit for a given expenditure of resources, and could even help establishing a roadmap for a future real-time weather forecasting capability.

Oreste Reale↗

TURBO-AE: An Aeroelastic Code for Propulsion Applications

NASA's Advanced Subsonic Technology (AST) program is developing new technologies to increase the fuel efficiency of commercial aircraft engines, improve the safety of engine operation, and reduce engine emissions and noise. With the development of new designs for ducted fans, compressors, and turbines to achieve these goals, a basic aeroelastic requirement is that there should be no flutter or high resonant blade stresses in the operating regime. To verify the aeroelastic soundness of these designs, we need an accurate prediction and analysis code. Such a two-dimensional viscous propulsion aeroelastic code, named TURBO-AE, is being developed at the NASA Lewis Research Center. The TURBO-AE aeroelastic code is based on a three-dimensional unsteady aerodynamic Euler/Navier-Stokes turbomachinery code TURBO, developed under a grant from NASA Lewis. TURBO-AE can model viscous flow effects that play an important role in certain aeroelastic problems, such as flutter with flow separation (or stall flutter) and flutter in the presence of shock and boundary-layer interaction. The structural dynamics representation of the blade in the TURBO-AE code is based on a normal mode representation. A finite element analysis code, such as NASTRAN, is used to calculate in-vacuum vibration modes and the associated natural frequency. A work-per-cycle approach is used to determine aeroelastic (flutter) stability. With this approach, the motion of the blade is prescribed to be a harmonic vibration in a specified in vacuum normal mode. The aerodynamic forces acting on the vibrating blade and the work done by these forces on the vibrating blade during a cycle of vibration are calculated. If positive work is being done on the blade by the aerodynamic forces, the blade is dynamically unstable, since it will extract energy from the flow, leading to an increase in the amplitude of the blade's oscillation. Initial calculations have been done for a configuration representative of the Energy Efficient Engine fan rotor. The accompanying figure shows the work-per-cycle after each cycle of vibration. It can be seen that the work-per-cycle does not vary much after the fourth cycle. The negative sign of the converged work-per-cycle shows that the fan blade is dynamically stable and will not flutter. TURBO-AE will provide a useful aeroelastic prediction/analysis capability for engine manufacturers. It will reduce design cycle times by allowing new blade designs to be verified for aeroelastic soundness before blades are built and tested. With this prediction capability, it will be possible to build thinner, lighter, and faster rotating blades without encountering aeroelastic problems like stall flutter and high-cycle fatigue due to forced vibrations.

Bakhle, Milind A.↗

Investigating Laser Beam Welding as an In-Space Joining Technique via Thermal Vacuum and Microgravity and Vacuum Experiments

In-space joining technologies are crucial for stimulating an in-space economy and for enabling sustained space exploration by in-space manufacturing and repair of metallic structures. Compared to brazing or soldering, in-space welding (ISW) can provide highly hermetic, strong, and complex joints, potentially without introducing additional material. However, the influence of extreme temperatures, reduced pressure, and reduced gravity on ISW is not yet fully elucidated. Several efforts at NASA are investigating laser beam welding (LBW) as a joining and repair method in both thermal vacuum (TVAC) and combined vacuum & reduced gravity environments. NASA Marshall Space Flight Center (MSFC) shepherded several ISW projects in its past, including the 1973 electron beam welding on Skylab, the 1989 low-power LBW on parabolic flights, and the unflown 1990s-era In-Space Welding Experiment. Recent parabolic flights and 3 degree-of-freedom ground testing build upon this heritage. A collaboration with the Ohio State University using NASA Langley Research Center (LaRC) hardware retrofitted for LBW achieved the first high-powered laser welds under vacuum and low gravity and developed a workforce capable developing such experimental hardware. A ground testing campaign at the MSFC Flat Floor simulated fit-up and welding representative of ISW in 3 degrees of freedom to emulate microgravity effects on inertial systems. One ongoing effort is a NASA Early Career Initiative project – Lunar Assembly and Servicing by Autonomous Robotics (LASAR). Ruggedized LBW components were developed by an external partner for use in TVAC. A TVAC-rated robotic arm was procured by MSFC and used in the first known robotic laser weld where all components save the laser generator were under vacuum. NASA Johnson Space Center (JSC) is advancing supervised autonomy of ISW. NASA LaRC continues to adapt their unique snowflake joint geometry, suitable for connecting segments in trusses and other structures, to LBW. Upcoming TVAC campaigns will focus on testing extreme temperatures, proving out autonomous operations, and demonstrating weld repair. Weld inspection will occur via a non-contact nondestructive evaluation (NDE) technique – electromagnetic acoustic transduction (EMAT). Another ongoing effort based at MSFC is the DISCMAN -- DIsk-Shaped Configurable and Modular vAcuum uNit – which seeks to development a compact, modular payload that can provide a vacuum environment while in a reduced gravity condition. This payload could support multiple in-space manufacturing developmental efforts, with the first demonstration technology being LBW. Currently, the design is targeting operations in the pressurized volume of a space station, but the payload could readily be adapted to other flight platforms such as parabolic or even suborbital vehicles. LASAR elucidates the effects of temperature and vacuum on LBW while DISCMAN probes those of vacuum and gravity. Through these complementary efforts, NASA is addressing the primary challenges of ISW across the space environment while simultaneously developing and maturing technologies including robotic systems and inspection methodologies for future practical implementation on the Moon and beyond. This approach is timely, as upcoming missions requiring sustained human presence in space will depend on reliable ISW capabilities to create robust metallic joints currently unproven in the space environment and to perform repairs in situ .

hypogravity↗

Integration mockup and process material management system

Work to define and develop a full scale Space Station Freedom (SSF) mockup with the flexibility to evolve into future designs, to validate techniques for maintenance and logistics and verify human task allocations and support trade studies is described. This work began in early 1985 and ended in August, 1991. The mockups are presently being used at MSFC in Building 4755 as a technology and design testbed, as well as for public display. Micro Craft also began work on the Process Material Management System (PMMS) under this contract. The PMMS simulator was a sealed enclosure for testing to identify liquids, gaseous, particulate samples, and specimen including, urine, waste water, condensate, hazardous gases, surrogate gasses, liquids, and solids. The SSF would require many trade studies to validate techniques for maintenance and logistics and verify system task allocations; it was necessary to develop a full scale mockup which would be representative of current SSF design with the ease of changing those designs as the SSF design evolved and changed. The tasks defined for Micro Craft were to provide the personnel, services, tools, and materials for the SSF mockup which would consist of four modules, nodes, interior components, and part task mockups of MSFC responsible engineering systems. This included the Engineering Control and Life Support Systems (ECLSS) testbed. For the initial study, the mockups were low fidelity, soft mockups of graphics art bottle, and other low cost materials, which evolved into higher fidelity mockups as the R&D design evolved, by modifying or rebuilding, an important cost saving factor in the design process. We designed, fabricated, and maintained the full size mockup shells and support stands. The shells consisted of cylinders, end cones, rings, longerons, docking ports, crew airlocks, and windows. The ECLSS required a heavier cylinder to support the ECLSS systems test program. Details of this activity will be covered. Support stands were designed and built for each module to sufficiently move and rotate each module. Secondary structures such as floors, ceilings, bulkheads, standoffs, racks, etc. were developed and built.

Verble, Adas James, Jr.↗

NASA’s Moon-to-Mars Planetary Autonomous Construction Technology Project: Overview and Status

NASA plans to land the first woman and next man on the Moon by 2025 through the initial Artemis missions. NASA and its international partners plan to establish a sustainable long-term presence on the lunar surface and build up infrastructure in the subsequent Artemis missions. The Lunar Surface Innovation Initiative (LSII), within NASA’s Space Technology Mission Directorate, aims to spur the creation of novel technologies needed for lunar surface exploration and accelerate the technology readiness of key systems and components. The primary thrust areas of LSII include sustainable power; dust mitigation; in-situ resource utilization; surface excavation, construction, and outfitting; and extreme access/extreme environments. The Moon-to-Mars Planetary Autonomous Construction Technology (MMPACT) projectwas initiated to address the lunar surface construction thrust area of LSII. The goal of the MMPACT project is to develop, deliver, and demonstrate on-demand capabilities to protect astronauts and create infrastructure on the lunar surface via construction of landing pads, habitats, shelters, roadways, berms and blast shields using lunar regolith-based materials. The MMPACT project is leveraging technology derived from NASA’s 3D Printed Mars Habitat Challenge along with contributions from other Government agencies, and multiple partners within industry and academia. The MMPACT project is comprised of three interrelated elements, construction hardware and process development; feedstock materials development; and microwave structure construction capabilities. These elements are working together to address the multiple challenges of infrastructure construction on the surface of the Moon including increased autonomy of operations, hardware operation and manufacturing under lunar environmental conditions, long-duration operation of mechanisms and parts, scale of construction activities, and material and construction requirements and standards. This presentation will summarize the status of development activities in each of the three elements, including testing of the various candidate materials, preliminary design concepts for future lunar infrastructure elements, and the vision for future technology demonstrations on the lunar surface. These demonstrations, targeting the mid-to-late 2020’s, are expected to enable landing pad construction and habitat construction resulting in commercial capabilities early in the next decade.

lunar infrastructure↗