Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

A study on inclusion formation mechanism in alpha-LiIO sub 3 crystals

The spatial distribution of inclusions in alpha-LiIO3 crystals by means of an argon laser beam scanning technique is studied. The effects of crystal dimensions and solution fluid flow on the inclusion formation in the alpha-LiIO3 crystals were observed. It was further shown that the fluid flow plays an important role in the formation of inclusions. The results obtained were further applied and verified by growing a perfect alpha-LiIO3 single crystal. An experimental foundation for further theoretical studies on the causes of inclusions may be provided.

Chen, W. C.↗
NASA NTRS1988

Solutal convection during directional solidification

During directional solidification of a binary alloy at constant velocity, buoyancy-driven fluid flow may occur due to the solute gradients generated by the solidification process. Numerical calculations of the solute and fluid flow fields in the melt have been carried out using finite differences in a two-dimensional, time-dependent model that assumes a planar crystal-melt interface and allows time-dependent gravitational accelerations. The container walls are rigid and perfectly insulating for solute. For constant vertical gravitational accelerations, as the solutal Rayleigh number is varied, multiple steady states and time-dependent states may occur. The bifurcation from the quiescent state may be subcritical or transcritical, depending on the aspect ratio of the container. Calculations have also been performed for a gravitational acceleration that is assumed to be uniform in magnitude with its direction rotating uniformly. Numerical results have been obtained for a Schmidt number of 10 and a gravitational acceleration of 0.0001 G. The maximum variation in the solute concentration at the crystal-melt interface is calculated for various values of the rotation rate of the gravitational acceleration.

Mcfadden, G. B.↗
NASA NTRS1994

Numerical comparison of convective heat transfer augmentation devices used in cooling channels of hypersonic vehicles

Hypersonic vehicles are exposed to extreme thermal conditions compared to subsonic aircraft; therefore, some level of thermal management is required to protect the materials used. Normally, hypersonic vehicles experience the highest temperatures in the nozzle throat, and aircraft and propulsion system leading edges. Convective heat transfer augmentation techniques can be used in the thermal management system to increase heat transfer of the cooling channels in those areas. The techniques studied in this report are pin-fin, offset-fin, ribbed and straight roughened channel. A smooth straight channel is used as the baseline for comparing the techniques. SINDA '85, a lumped parameter finite difference thermal analyzer, is used to model the channels. Subroutines are added to model the fluid flow assuming steady one dimensional compressible flow with heat addition and friction. Correlations for convective heat transfer and friction are used in conjunction with the fluid flow analysis mentioned. As expected, the pin-fin arrangement has the highest heat transfer coefficient and the largest pressure drop. All the other devices fall in between the pin-fin and smooth straight channel. The selection of the best heat augmentation method depends on the design requirements. A good approach may be a channel using a combination of the techniques. For instance, several rows of pin-fins may be located at the region of highest heat flux, surrounded by some of the other techniques. Thus, the heat transfer coefficient is maximized at the region of highest heat flux while the pressure drop is not excessive.

Maldonado, Jaime J.↗
NASA NTRS1972

Particle trackability considerations for laser Doppler velocimetry

The technique for calculating single particle trackability in a fluid flow in terms of rms velocities is discussed. The general equation for the motion of a single particle as a response to a fluid flow driving force is presented, and a criterion for greatly simplifying the governing equation is developed. It is shown that in the case of large particle- to fluid-density ratio and low frequency fluid motion compared to the natural time constant of the particle response, the governing equation can be reduced to a simple balance of inertia force and linear viscous drag (i.e., Stokes drag).

Karchmer, A. M.↗
NASA NTRS1988

Numerical investigations in three-dimensional internal flows

Renewed interest in simulation of high enthalpy flows was brought about by interest in the design and testing of hypersonic propulsion components. This renewed interest has led to refurbishment of high speed ground based wind tunnel facilities. Simulation of the high enthalpy flows occurring in the NASP propulsion system is of particular interest. Studying the combustor presentes some of the more challenging problems in the ground based simulation of the fluid flow. A difficulty in simulating the required conditions at the entrance to the combustor is related to achieveing a sufficiently high static pressure such that combustion would be possible at a high Mach number. An analysis of the flow within the original nozzle was not performed previously using numerical simulations, although it was operated experimentally. A Navier-Stokes code was chosen in the present study to examine analytically the flow within representative selected nozzles for use in combustion experiments. The numerical simulation of these fluid flows is popular and may be able to shed light on the direction that redesign of the shock tube nozzles should take. The numerical codes were modified to account for the axially symmetric flow field, for the inclusion of equilibrium real gas effects and for ideal gases whose thermodynamic properties are frozen at the stagnation conditions. Numerical simulation of flows within the original and two proposed nozzles, including the energy lost to the relatively cold walls, are investigated.

Rose, William C.↗
NASA NTRS2020

Simulation of Hydrogen Flow in a Nuclear-Thermal Propulsion Reactor Subsystem: Conjugate Heat Transfer in Surrogate Fuel Elements and Flow Through the Dome Inlet to the Fuel Elements

NASA is performing research related to a Nuclear-Thermal Propulsion (NTP) engine as a step toward future manned missions to Mars. BWX Technologies (BWXT), in conjunction with NASA, is developing the reactor subsystem for that NTP engine design. As a subset of the reactor subsystem, the fuel elements have continued to evolve in design, as well. A set of experiments within the Nuclear Thermal Reactor Element Environmental Simulator at NASA Marshall has been developed to compliment that design process, including a series of surrogate fuel elements. Before the experiments of each surrogate can be completed, they must be deemed safe using structural analysis, which itself requires thermal and conjugate heat transfer analyses of the articles. Therefore, conjugate heat transfer simulations of the hydrogen flow through the test article fuel element surrogates were developed to provide estimates of heating, as well as to provide assessments of the fluid flow through the elements. The set of simulations involved not only the separate test conditions, but also a sensitivity study to estimate the effect of physical parameter uncertainty on the selected quantities of interest. Additionally, the fluid flow through the fore section inner plenum dome to the entrances of the fuel elements, another section of the reactor subsystem still under active development, was simulated and analyzed. The simulations show the extent of non-uniformity in the mass flow distribution across the dome outlets. Furthermore, additional analyses estimate the effects of required flow blockages on the potential development of flow dynamics. These analyses were used in the design cycle to make improvements to the reactor subsystem design.

Kalen E. Braman↗
NASA NTRS1970

Design and development criteria for metal bellows

Experimental research describes fluid flow and the fluid-elastic mechanism causing bellows flow excitation, and aids in design of conventional bellows liner which suppresses flow-induced vibrations. Analytical models facilitate prediction of flow excitation occurrence and estimation of severity of bellows vibrations.

Gerlach, C. R.↗
NASA NTRS1990

Instability during directional solidification - Gravitational effects

After an elementary introduction to solidification, recent research that attempts to understand the interaction of fluid flow with a crystal-melt interface under gravitational influence using linear stability analysis is reviewed. Recent numerical calculations of fluid flow and interface morphology during alloy solidification are briefly discussed.

Coriell, S. R.↗
NASA NTRS1993

Measured and predicted effects of gravity level on directional dendritic solidification of NH4Cl-H2O

Dendritic growth front rates during vertical directional solidification are predicted for gravity levels of 10 exp 0 g sub e (where e is earth gravity), 10 exp -1 g sub e, 10 exp -2 g sub e, 10 exp -3 g sub e, 10 exp -4 g sub e, and 10 exp -5 g sub e (microgravity) for the physical conditions used for a recent ammonium chloride-water solidification experiment on the International Microgravity Laboratory I (IMLI). The growth front rates at 10 exp 0 g sub e and 10 exp -5 g sub e are validated using ground based laboratory and IMLI experimental data. As the gravity decreases, the growth rates increase until they approach a maximum at approximately 10 exp -4 g sub e. The 10 exp -4 and 10 exp -5 levels are equivalent. Liquid concentration and volume fraction, temperature profiles and fluid flow velocities are also calculated. Kinetic energy calculations for each of the six gravity levels indicate that the threshold for fluid flow to affect the growth front rate is in the range of 10 exp -8 ergs.

Mccay, T. D.↗
NASA NTRS2004

NASA Multidimensional Stirling Convertor Code Developed

A high-efficiency Stirling Radioisotope Generator (SRG) for use on potential NASA Space Science missions is being developed by the Department of Energy, Lockheed Martin, Stirling Technology Company, and the NASA Glenn Research Center. These missions may include providing spacecraft onboard electric power for deep space missions or power for unmanned Mars rovers. Glenn is also developing advanced technology for Stirling convertors, aimed at substantially improving the specific power and efficiency of the convertor and the overall power system. Performance and mass improvement goals have been established for second- and third-generation Stirling radioisotope power systems. Multiple efforts are underway to achieve these goals, both in house at Glenn and under various grants and contracts. These efforts include the development of a multidimensional Stirling computational fluid dynamics code, high-temperature materials, advanced controllers, an end-to-end system dynamics model, low-vibration techniques, advanced regenerators, and a lightweight convertor. Under a NASA grant, Cleveland State University (CSU) and its subcontractors, the University of Minnesota (UMN) and Gedeon Associates, have developed a twodimensional computer simulation of a CSUmod Stirling convertor. The CFD-ACE commercial software developed by CFD Research Corp. of Huntsville, Alabama, is being used. The CSUmod is a scaled version of the Stirling Technology Demonstrator Convertor (TDC), which was designed and fabricated by the Stirling Technology Company and is being tested by NASA. The schematic illustrates the structure of this model. Modeled are the fluid-flow and heat-transfer phenomena that occur in the expansion space, the heater, the regenerator, the cooler, the compression space, the surrounding walls, and the moving piston and displacer. In addition, the overall heat transfer, the indicated power, and the efficiency can be calculated. The CSUmod model is being converted to a two-dimensional model of the TDC at NASA Glenn. Validation of the multidimensional Stirling code is an important part of the grant effort. UMN has been generating data in an oscillating-flow test facility using two different test sections: a 90 turn and a cooler/regenerator/heater test section. CSU has created computational fluid dynamics models of both these test sections and has been making comparisons with the data, then improving their models to improve the agreement with the test data. CSU has also been using data available in the literature for code validation. UMN is now preparing to begin fabrication of a new 180 turn test section that will be more representative of certain portions of the Stirling engine geometry. Simulations to almost periodic steady state with the two-dimensional CSUmod model indicate that, to reach periodic steady state on a single 2-GHz desktop computer, 75 to 100 complete simulation cycles would be required and between 1 and 2 months of computer time. Therefore, Glenn has purchased the first 8 computers, of a 64-computer cluster, to be run in parallel to accelerate the simulation. On the basis of CFD Research Corp.'s experience with running the parallelized version of CFD-ACE on their clusters, we estimate that the complete 64-computer cluster will reduce simulation computing time by a factor of about 40. Plans are to continue development of these multidimensional Stirling codes and to use them to study the fluid-flow and heat-transfer phenomena that occur inside Stirling convertors. This is expected to lead to improved thermodynamic loss understanding, onedimensional design and performance codes, and engine performance.

Tew, Roy C.↗
NASA NTRSDate not supplied

Demonstration of Fluid Dynamics for Plant Growing Systems in Varied Gravity Environments Through Scaled Capillary Models

The development of reliable and bioregenerative crop growth production systems is vital for human exploration into deep space. As humans prepare for space travel beyond LEO, scientists need to find a way to provide reliable and adequate water delivery for all stages of the plant's life cycle. Past production systems struggled with this and often led to overwatering in the system. To better understand this issue, NASA's Plant Water Management (PWM) experiments were able to model fluid flow through granular substrates, specifically a clay-based material arcilite, in 0-G. The PWM study can help researchers to predict fluid flow through the systems, however their model only works for an arcilite based system and was unable to account for different stages of plant growth. For future missions, payload requirements to support crop production system will need to be limited, leading to the use of in situ resources. This project aims to validate the PWM experiments as well as incorporate various materials into the design for growth systems. To meet these objectives, a series of terrestrial experiments will be deployed to mimic all gravities. By modifying the material, fluid, and size of the test subjects, the effect of Earth's gravity can be minimized. This project will aid researchers in the design of future crop production systems for surface missions by creating a refined model that can be used at all stages of plant growth and utilize in situ resources.

Plant Biology↗
NASA NTRS1985

Convection During Unidirectional Solidification

The fluid flow and solute segregation which occur during directional solidification, including effects of gravity and microgravity were studied. The nature of the fluid flow, its effects on the shape of the crystal-metal interface and the resulting distribution of solutes are examined. During solidification of a binary alloy at constant velocity vertically upwards, thermosolutal convection occurs if the solute rejection or preferential incorporation at the crystal-melt interface decreases the density of the melt. Numerical calculations of the solute, temperature, and flow fields are carried out by using previously developed algorithms for Schmidt numbers Sc = 1, 10, 81. The time periodic flow, which occurs over a narrow range of parameters, is investigated.

Coriell, S. R.↗
NASA NTRS1996

Directional Solidification of Mercury Cadmium Telluride During the Second United States Microgravity Payload Mission (USMP-2)

As a solid solution semiconductor having, a large separation between liquidus and solidus, mercury cadmium telluride (MCT) presents a formidable challenge to crystal growers desiring an alloy of high compositional uniformity. To avoid constitutional supercooling during Bridgman crystal growth it is necessary to solidify slowly in a high temperature gradient region. The necessary translation rate of less than 1 mm/hr results in a situation where fluid flow induced by gravity on earth is a significant factor in material transport. The Advanced Automated Directional Solidification Furnace (AADSF) is equipped to provide the stable thermal environment with a high gradient, and the required slow translation rate needed. Ground based experiments in AADSF show clearly the dominance of flow driven transport. The first flight of AADSF in low gravity on USMP-2 provided an opportunity to test theories of fluid flow in MCT and showed several solidification regimes which are very different from those observed on earth. Residual acceleration vectors in the orbiter during the mission were measured by the Orbital Acceleration Research Experiment (OARE), and correlated well with observed compositional differences in the samples.

Gillies, D. C.↗
DOE OSTI2020

PFLOTRAN-SIP: A PFLOTRAN Module for Simulating Spectral-Induced Polarization of Electrical Impedance Data

Spectral induced polarization (SIP) is a non-intrusive geophysical method that collects chargeability information (the ability of a material to retain charge) in the time domain or its phase shift in the frequency domain. Although SIP is a temporal method, it cannot measure the dynamics of flow and solute/species transport in the subsurface over long times (i.e., 10–100 s of years). Data collected with the SIP technique need to be coupled with fluid flow and reactive-transport models in order to capture long-term dynamics. To address this challenge, PFLOTRAN-SIP was built to couple SIP data to fluid flow and solute transport processes. Specifically, this framework couples the subsurface flow and transport simulator PFLOTRAN and geoelectrical simulator E4D without sacrificing computational performance. PFLOTRAN solves the coupled flow and solute-transport process models in order to estimate solute concentrations, which were used in Archie’s model to compute bulk electrical conductivities at near-zero frequency. These bulk electrical conductivities were modified while using the Cole–Cole model to account for frequency dependence. Using the estimated frequency-dependent bulk conductivities, E4D simulated the real and complex electrical potential signals for selected frequencies for SIP. These frequency-dependent bulk conductivities contain information that is relevant to geochemical changes in the system. This study demonstrated that the PFLOTRAN-SIP framework is able to detect the presence of a tracer in the subsurface. SIP offers a significant benefit over ERT in the form of greater information content. It provided multiple datasets at different frequencies that better constrained the tracer distribution in the subsurface. Consequently, this framework allows for practitioners of environmental hydrogeophysics and biogeophysics to monitor the subsurface with improved resolution.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2006

Using Magnetic Field Gradients to Simulate Variable Gravity in Fluids and Materials Experiments

Fluid flow due to a gravitational field is caused by sedimentation, thermal buoyancy, or solutal buoyancy induced convection. During crystal growth, for example, these flows are undesirable and can lead to crystal imperfections. While crystallization in microgravity can approach diffusion limited growth conditions (no convection), terrestrially strong magnetic fields can be used to control fluid flow and sedimentation effects. In this work, a theory is presented on the stability of solutal convection of a magnetized fluid(weak1y paramagnetic) in the presence of a magnetic field. The requirements for stability are developed and compared to experiments performed within the bore of a superconducting magnet. The theoretical predictions are in good agreement with the experiments. Extension of the technique can also be applied to study artificial gravity requirements for long duration exploration missions. Discussion of this application with preliminary experiments and application of the technique to crystal growth will be provided.

Ramachandran, Narayanan↗
DOE OSTI2021

Machine learning to identify geologic factors associated with production in geothermal fields: A casestudy using 3D geologic data, Brady geothermal field, Nevada

In this paper, we present an analysis using unsupervised machine learning (ML) to identify the key geologic factors that contribute to the geothermal production in the Brady geothermal field. Brady is a hydrothermal system in northwestern Nevada that supports both electricity production and direct use of hydrothermal fluids. Transmissive fluid flow pathways are relatively rare in the subsurface but are critical components of hydrothermal systems like Brady and many other types of fluid flow systems in fractured rock. The ML method, non-negative matrix factorization with k-means clustering (NMFk), is applied to a library of fourteen 3D geologic characteristics hypothesized to control hydrothermal circulation in the Brady geothermal field. Our results indicate the macro-scale faults and a local step-over in the fault system preferentially occur along with production wells when compared to injection wells and non-productive wells. We infer that these are the key geologic characteristics that control the through-going hydrothermal transmission pathways at Brady. Our results demonstrate 1) the specific geologic controls on the Brady hydrothermal system and 2) the efficacy of pairing ML techniques with 3D geologic characterization to enhance the understanding of subsurface processes.

15 GEOTHERMAL ENERGY↗
NASA NTRS1998

The Role of Marangoni Convection for the FZ-Growth of Silicon

Fluctuations of the electrical resistivity due to inhomogeneous dopant distribution are still a serious problem for the industrial processing yield of doped silicon crystals. In the case of silicon floating-zone growth, the main sources of these inhomogeneities are time- dependent flows in the liquid phase during the growth process. Excluding radio frequency (RF) induced convection, buoyancy and thermocapillary (Marangoni) convection are the two natural reasons for fluid flow. Both originate from temperature/concentration gradients in the melt, buoyancy convection through thermal/concentrational volume expansion, and thermocapillary convection through the temperature/concentration dependence of the surface tension. To improve the properties of grown crystals, knowledge of the strength, the characteristic, and the relation of these two flow mechanisms is essential. By the use of microgravity, the effect and the strength of buoyancy (gravity dependent) and thermocapillary (gravity independent) convection can be separated and clarified. Applying magnetic fields, both convective modes can be influenced: fluid flow can either be damped (static magnetic fields) or overlaid by a regular flow regime (rotating magnetic fields). Two complementary approaches have been pursued: Silicon full zones (experiments on the German sounding rockets TEXUS 7, 12, 22, 29, and 36) with the maximum temperature at half of the zone height and silicon half zones (experiments on the Japanese sounding rockets TR-IA4 and 6) with the maximum temperature at the top of the melt. With the full zone arrangement, the intensity and the frequency of the dopant striations could be determined and the critical Marangoni number could be identified. The half zone configuration is suited to classify the flow pattern and to measure the amplitude and the frequency of temperature fluctuations in the melt by inserting thermocouples or temperature sensors into the melt. All experiments have been carried out in monoellipsoid mirror furnaces. Typical zone geometries are approx. 8 to 14 mm in diameter and height. The crystals grown under microgravity are compared to crystals grown in static axial magnetic fields (B<5 tesla) and in transversal rotating magnetic fields (B<7.5 mT / f=50 Hz). Experimental results are completed by 3D numerical simulations: the obtained temperature and concentration distribution in the melt confirm the damping effect of rotating magnetic fields and explain the change in the radial segregation under static magnetic fields.

Dold, P.↗