Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

A Revised Capsule Design for the Accelerated Testing of Advanced Reactor Fuels

Testing of fast reactor fuel is currently challenging because of the thermal neutron spectrum of the Advanced Test Reactor (ATR) and the fact that ATR coolant is substantially below typical temperatures found in liquid metal-cooled fast reactors. Despite these issues, since 2003 the Idaho National Laboratory (INL) has successfully tested a variety of metallic, oxide, and nitride fuels for fast reactor applications. There are, however, opportunities to improve the experiments so that the time required to reach a desired burnup can be reduced, and so the sensitivity of the experiments to fabrication tolerances can be minimized. A revised capsule design exploits the use of smaller diameter rodlets to increase power densities and correspondingly reduce the irradiation time required to reach high burnup. Thermal and nuclear analyses indicate that the time to reach 30at% burnup could be reduced from about 12 years to approximately 2-3 years if the fuel diameter is reduced by one-half and to around 1-2 years if the diameter is reduced by one-third. In addition, reducing fuel diameter improves the radial power distribution in the fuel without the use of cadmium shrouding. This observation opens up the possibility of testing advanced reactor fuel systems in Small I locations in the ATR where there is substantial unused capacity. Although not directly tied to a revised capsule design, post-irradiation furnace testing is proposed to provide time-to-failure data that will be helpful in the benchmarking of fuel performance models and in assessing the performance of new fuel designs relative to more standard fast reactor fuel systems. In this paradigm, ATR irradiation experiments will be viewed more as preparation for furnace testing than as experiments that exist in isolation. An added benefit to furnace testing is that uncertainties in temperatures will significantly be reduced relative to non-instrumented capsules in the ATR. The time and cost in developing this experimental capability is expected to be reduced considerably because of the availability of the blister anneal furnace used by the HPRR program. A key issue in the experiment approach is the potential for non-prototypical rodlet dimensions to influence the observed performance of a given fuel design. For example, a qualitative assessment indicates that the effects of fuel-cladding chemical interactions during furnace testing might be more pronounced in reduced diameter rodlets simply because thinner cladding would be more sensitive to a given depth of fission product penetration. In a traditional empirically-driven approach to fuel qualification, any change from prototypical behavior is undesirable because the resulting data cannot easily be assimilated into a statistical correlation. However, in the current approach, systematic variations in fuel diameter provide the opportunity to benchmark fuel performance models over a wider range of parameter space, which in turn is expected to improve understanding and result in better, more physically based models in the long term.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Zircaloy Oxide Growth

The goal of the research is to create a standard for growing an oxide layer on zircaloy nuclear fuel cladding to aid in qualifying new eddy current probes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Large-scale parametric modeling of spent nuclear fuel dynamics in the 30 cm package drop scenario

Packages used to transport spent nuclear fuel (SNF) are required by the U.S. Code of Federal Regulations 10 CFR 71.71 to demonstrate satisfactory performance during a drop scenario. While the CFR is meant to ensure safe package function, it does not evaluate survival of the SNF within. The U.S. Department of Energy Spent Fuel and Waste Science and Technology program is working on closing the knowledge gap related to the response of SNF to external mechanical loads, including the hypothetical 30 cm package drop scenario in the CFR. In support of this effort, LS-DYNA finite element simulations were developed by Pacific Northwest National Laboratory (PNNL) to model generic drop scenarios at both the package and fuel assembly level. The models were validated against one-third scale package and full scale fuel assembly drop test data and were exercised to predict fuel cladding strains in a narrow range of model configurations. This work describes a large-scale parametric study conducted by PNNL using the previously developed and validated PWR finite element model, with the addition of a new generic BWR assembly model. The motivation for the parametric study was to characterize the broad range of SNF responses in the 30 cm package drop scenario. This was accomplished by varying the drop orientation, fuel assembly type (17x17 PWR and 10x10 BWR), burnup, cladding temperature, spacer grid buckling load, package mass, impact limiter stiffness, and mechanical gap conditions within the basket. A MATLAB framework was developed to automate LS-DYNA model generation and execution on PNNL institutional computing resources. In total, over 2000 simulations were performed. For each simulation, the SNF response was quantified in terms of permanent grid deformation, fuel rod contact pressure, and strains within the fuel rods, guide tubes, and water rods. The results provide valuable insight into the range of responses that could be reasonably expected from SNF in the hypothetical drop scenario, as well as the sensitivity to each input parameter. The results of this parametric study are a key component of the testing and modeling strategy the Spent Fuel and Waste Science and Technology program is using to close the external loads knowledge gap.

Kadooka, Kevin↗

Simulation of 1% hot leg SBLOCA with TRACE5

During a Small Break Loss-of-Coolant Accident (SBLOCA) transient, depressurization can be slow enough to delay the Accumulators (ACC) entry for a long time. Actuation of High Pressure Injection (HPI) system is then necessary in order to maintain the core temperature low enough to avoid core boil off, and consequently avoiding the core level to fall below fuel rods level, thus producing a temperature trip in the fuel cladding. In this frame, the OECD/NEA ROSA Project Test 1.2 (SB-HL-17 in Japan Atomic Energy Agency (JAEA)) has been simulated using the thermal-hydraulic code TRACES. Test 1.2 was performed in the Large Scale Test Facility (LSTF) reproducing a 1% hot leg SBLOCA in a Pressurized Water Reactor (PWR). A comparison between experimental and the main simulated variables was performed to study the effect of important parameters (liquid stratification, geometry and size) to model the break. Finally, in an Emergency Core Cooling System (ECCS) failure scenario, loss of coolant is large enough to produce core boil-off and a Peak Cladding Temperature (PCT) excursion. With this purpose a sensitivity analysis varying the HPI mass flow rate has been performed covering the range between HPI actuation and failure. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Post quench ductility of Zirconium alloy cladding materials - 6.2 STP-2016-0088

The ductility of zirconium-based alloys after steam oxidation at high temperature, followed by quenching in water, is of significant interest for the nuclear industry. High temperature steam oxidation and quenching of nuclear fuel cladding occurs during postulated loss-of-coolant accidents (LOCA). The industry is currently establishing in-reactor operation limits for peak cladding temperature and time at temperature based on the measured ductile-to-brittle transition of different cladding materials, both in the as-fabricated condition and using hydrogen charging as a surrogate for in-reactor operation. Aiming to study possible differences in post-quench ductility (PQD) caused by differences in chemical composition, extensive testing has been performed on Zircaloy-4, ZIRLO{sup R} and Optimized ZIRLO{sup TM} cladding materials as a function of hydrogen content, extent of oxidation and peak cladding temperature. The results show similar ductile-to-brittle transition for the alloys studied, in spite of the differences in chemical composition, with a decrease in the extent of oxidation to reach the ductile-to-brittle transition with increasing hydrogen content. Microstructural characterization was performed to investigate the evolution of the oxygen enriched layer that appears underneath the oxide, both during the time at high temperature and during cooling. Significantly different morphologies of the oxygen enriched layer are observed with different cooling rates, particularly for alloys containing niobium. Possible mechanisms for the development of the oxygen enriched layer are discussed (authors)

36 MATERIALS SCIENCE↗

Post-quench ductility of zirconium alloy cladding materials - 2016-0088

The ductility of zirconium-based alloys after steam oxidation at high temperatures, followed by quenching in water, is of significant interest for the nuclear industry. High-temperature steam oxidation and quenching of nuclear fuel cladding occurs during postulated loss-of-coolant accidents. The industry is currently establishing in-reactor operation limits for peak cladding temperature and time at temperature based on the measured ductile-to-brittle transition of different cladding materials, both in the as-fabricated condition and using hydrogen charging as a surrogate for in-reactor operation. Aiming to study possible differences in post-quench ductility caused by differences in chemical composition, extensive testing on Zircaloy-4, ZIRLO{sup R}, and Optimized ZIRLO{sup TM} cladding materials as a function of hydrogen content, extent of oxidation, and peak cladding temperature was performed. The results showed similar ductile-to-brittle transition for the alloys studied despite differences in chemical composition, with a decrease in the extent of oxidation to reach the ductile to brittle transition with increasing hydrogen content. Microstructural characterization was performed to investigate the evolution of the oxygen-enriched layer that forms underneath the oxide, both during the time at high temperatures and during cooling. Significantly different morphologies of the oxygen-enriched layer were observed with different cooling rates, particularly for alloys containing niobium. Possible mechanisms for the development of the oxygen-enriched layer are discussed. (authors)

36 MATERIALS SCIENCE↗

Preliminary HEA Solid Phase Processing Development Report

The development of high temperature fuel cladding materials to withstand a variety of extreme environments have received much attention. Several potential materials systems that have been identified for the fuel systems and core structural materials application in advanced reactor systems are ferritic/martensitic steel (e.g., HT9), austenitic stainless steels (e.g., 316 LN), oxide-dispersion strengthened steels (e.g., 12 YWT), Ni-based alloys and ceramic-based composites depending on the type of the reactors. Though these material systems have promising properties conducive for radiation-resistant performance, they suffer beyond the design-limit from one or more damage processes such as void swelling, radiation embrittlement, phase instability, corrosion, and limited creep life.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel Cycle System Analysis Implications of Sodium-Cooled Metal-Fueled Fast Reactor Transuranic Conversion Ratio

If advanced fuel cycles are to include a large number of fast reactors (FRs), what should be the transuranic (TRU) conversion ratio (CR)? The nuclear energy era started with the assumption that they should be breeder reactors (CR > 1), but the full range of possible CRs eventually received attention. For example, during the recent U.S. Global Nuclear Energy Partnership program, the proposal was burner reactors (CR < 1). Yet, more recently, Massachusetts Institute of Technology's "Future of the Nuclear Fuel Cycle" proposed CR [approximately] 1. Meanwhile, the French company EDF remains focused on breeders. At least one of the reasons for the differences of approach is different fuel cycle objectives. To clarify matters, this paper analyzes the impact of TRU CR on many parameters relevant to fuel cycle systems and therefore spans a broad range of topic areas. The analyses are based on a FR physics parameter scan of TRU CR from 0 to [approximately]1.8 in a sodium-cooled metal-fueled FR (SMFR), in which the fuel from uranium-oxide-fueled light water reactors (LWRs) is recycled directly to FRs and FRs displace LWRs in the fleet. In this instance, the FRs are sodium cooled and metal fueled. Generally, it is assumed that all TRU elements are recycled, which maximizes uranium ore utilization for a given TRU CR and waste radiotoxicity reduction and is consistent with the assumption of used metal fuel separated by electrochemical means. In these analyses, the fuel burnup was constrained by imposing a neutron fluence limit to fuel cladding to the same constant value. This paper first presents static, time-independent measures of performance for the LWR [right arrow] FR fuel cycle, including mass, heat, gamma emission, radiotoxicity, and the two figures of merit for materials for weapon attractiveness developed by C. Bathke et al. No new fuel cycle will achieve a static equilibrium in the foreseeable future. Therefore, additional analyses are shown with dynamic, time-dependent measures of performance including uranium usage, TRU inventory, and radiotoxicity to evaluate the complex impacts of transition from the current uranium-fueled LWR system, and other more realistic impacts that may not be intuited from the time-independent steady-state conditions of the end-state fuel cycle. These analyses were performed using the Verifiable Fuel Cycle Simulation Model VISION. Compared with static calculations, dynamic results paint a different picture of option space and the urgency of starting a FR fleet. For example, in a static analysis, there is a sharp increase in uranium utilization as CR exceeds 1.0 (burner versus breeder). However, in dynamic analyses that examine uranium use over the next 1 to 2 centuries, behavior as CR crosses the 1.0 threshold is smooth, and other parameters such as the time required outside of reactors to recycle fuel become important. Overall, we find that there is no unambiguously superior value of TRU CR; preferences depend on the relative importance of different fuel cycle system objectives.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Drying Spent Magnox Fuel for Interim Dry Storage

Spent Magnox fuel is usually stored under water for shielding and cooling following use in-reactor, but the storage water can react with Magnox clad fuel and cause corrosion and forms a sludge which generates a secondary waste product. One option to prevent unwanted corrosion and avoid expensive waste management is to dry the wet fuel. This project aims to test a drying process which will convert wet and corroded Magnox fuel to a stable form to demonstrate viability for conversion from wet to dry storage. Samples of corroded Magnox supplied by National Nuclear Laboratory. Corrosion product retrieved by various methods including dry scraping, ultrasonic treatment to form sludge and sludge drying to isolate suspension. TGA undertaken on Sample 1 and Sample 2, with brucite and hydromagnesite for comparison. Both samples showed ∼10% mass loss up to 250 deg. C attributable to water held in sample. Mass loss from dehydroxylation which liberates further water in both samples. TGA data plotted alongside chemically pure brucite and hydromagnesite shows expected similarities/differences between Sample 1(mostly brucite) and Sample 2 (brucite/hydromagnesite mixture). Following treatment, dried samples observed to slowly gain mass in ambient conditions. Presumed to be hygroscopic absorption of air water vapour as effect is reversible, with similar effect observed for hydromagnesite and brucite. Etched Magnox vacuum dried for 3.5 h at 90 deg. C to test for reaction with residual water - some discoloration but no noticeable corrosion observed. Drying etched Magnox metal to observe surface effects/corrosion during drying process.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

An x-ray absorption spectroscopy study of Mo oxidation in Pb at elevated temperatures

The corrosion of fuel cladding and structural materials by lead and lead-bismuth eutectic in the liquid state at elevated temperatures is an issue that must be considered when designing advanced nuclear systems and high-power spallation neutron targets. In this work, lead corrosion studies of molybdenum were performed to investigate the interaction layer as a function of temperature by X-ray absorption spectroscopy. In situ X-ray absorption measurements on a Mo substrate with a 3-6 {micro}m layer of Pb deposited by thermal evaporation were performed at temperatures up to 900 C and at a 15{sup o} angle to the incident X-rays. The changes in the local atomic structure of the corrosion layer are visible in the difference extended X-ray absorption fine structure and the linear combination fitting of the X-ray absorption near-edge structure to as-deposited molybdenum sample and molybdenum oxide (MoO{sub 2} and MoO{sub 3}) standards. The data are consistent with the appearance of MoO{sub 3} in an intermediate temperature range (650-800 C) and the more stable MoO{sub 2} phase dominating at high and low temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effects of Residual Water on Storage Canister Internal Components

This report describes an evaluation of the spent nuclear fuel cladding and canister internal materials’ corrosion/oxidation due to (inadvertent) residual free water inside a dry storage canister post-dryout. Drying of spent nuclear fuel (SNF) and the impact of (inadvertent) residual water in a SNF canister is being addressed under the DOE-NE Spent Fuel and Waste Science and Technology (SFWST) program to ensure the safe extended dry storage and transportation of commercial SNF. A long-standing understanding has been that the amount of residual water in a storage canister after vacuum drying is not expected to be much more than trace amounts of 0.43 gram mole. However, recent findings from the High Burnup Demonstration project, and an Integrated Research Project show that residual free water well above the amount of approximately 0.43 gm-moles that had been assumed for a 3 torr rebound pressure, may remain within an SNF canister following prototypic drying. In fact, an NRC-NMSS sponsored study considered residual water amount as high as 55 moles. Considering the recent findings and the NRC-sponsored work, this present work was conducted to study the effects of unspecified amount of residual water on oxidation and corrosion of canister internals, i.e., it was assumed that the residual water amount is not limiting. It was assumed that the spent nuclear fuel content in the canister is not exposed to the internal environment, i.e., the packaged canister does not contain any damaged (breached) fuel.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

IER 296 Experiment- Thermal Feasibility Analysis [Slides]

This set of slides summarizes progress, highlights, and issues related to the LANL design engineering effort for the IER 296 critical experiment. The experiment configuration described in Section 5.1.1 of CED-1 IRSN Preliminary Design for Thermal/Epithermal Experiments with MOX FUEL (TEX-MOX) is re-examined in a finite element analysis model using design geometry utilized in the Chlorine Worth Study (CWS) Experiments. Preliminary results and design considerations are presented. Additional analysis has been performed based on comments from the collaborative virtual meeting on 12JAN2023. Specifically, the fuel cladding and gas gap have been included in the thermal analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Scoping Study for Fast Flux Testing in the Advanced Test Reactor

The value of fast spectrum reactors remains prominent in the nuclear technology portfolio. The performance of these reactors can be maximized with advancements in nuclear fuel technologies, but development of these technologies is currently held back by lack of fast spectrum test reactors available to the United States. Spectral modification of experiment positions in the thermal spectrum Advanced Test Reactor (ATR) has long been used to support fast reactor fuel development, but these methods have not been progressed to their full potential. This study investigated the use of concentric rings of aluminum-clad fuel plates in ATR flux traps and thermal neutron absorbing filters to increase fast neutron flux on test specimens. This concept was termed the Boosted Energy Advanced Spectrum Test (BEAST). This approach will enable irradiation of advanced fuel designs in prototypic-length fuel pins and representative flux environment to support post irradiation exams, enable transient testing, and produce the type of data that will permit lead test assembly irradiations in true Sodium Fast Reactors (SFRs) when they become available. Neutronic predictions were performed to investigate BEAST design options and thermal hydraulic models were produced to ensure feasibility of BEAST. Two versions were considered based on the geometric limitations of ATR’s small and large flux traps. The small version was found to be preferable due to slightly higher fast flux and fast-to-thermal neutron ratio. Perhaps more influentially, the small flux trap option was also preferred to avoid conflict with ongoing very high temperature reactor fuel irradiation programs in ATR’s large northeast flux trap. The small flux trap option provided less than half the test volume of the large version, but still had adequate volume for seven SFR pins in cross section which could be stacked two-high in ATR’s 1.2m long core to accommodate up to 14 EBR-II size pins. The preference for the small flux trap configuration should be revisited if additional collaborative test programs emerge with the need to irradiate a significant volume of additional specimens. Calculations were performed regarding a lithium deuteride ring to convert thermal neutrons into 14 MeV fusion neutrons. At the time this report was written these calculations were partially complete and it remains to be seen whether the concept would be worth including in BEAST. Given the preference for the small flux trap option, which does not afford enough room for the 14 MeV ring, it was concluded to defer future work on the lithium deuteride ring. This decision could be revisited if fusion material research programs emerge for collaborative testing in BEAST. A cadmium-lined specimen holder design was found to be adequate in filtering thermal neutrons and preferred over other neutron absorbers based on past experience with cadmium baskets. It was acknowledged that cadmium-bearing hardware would become depleted and need to be replaced occasionally, which appeared feasible from a mechanical design perspective. Neutronic studies investigated different enrichment levels in the booster fuel using uranium-molybdenum alloy dispersion fuel which has performed well in past ATR irradiations. Both options were able to drive fuel pins to SFR-like fission heating rates. The high enriched booster fuel option outperformed the low enriched option by ~20% on key metrics including fast flux and fast-to-thermal ratio, but the low enriched option was favored in order to broaden options for potential fuel suppliers. The preferred BEAST design options including cadmium filter with low enriched booster fuel in the small flux trap configuration was predicted to achieve 6.2E14 n/cm2sec fast flux (>0.1 MeV) with a fast-to-thermal ratio of 44.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The harmony between nuclear reactions and nuclear reactor structures and systems

Advanced nuclear energy is one extremely viable approach for achieving the required goals. With its extraordinarily high energy density (both, per unit mass and per unit volume), it produces over seven orders of magnitude less waste than fossil fuels per unit of energy generated. Applying nano-technologies to nuclear reactors could potentially produce the extraordinary performance required. The actual nuclear reactors lack of performances, the complexity and hazard of the fuel cycle are in part due to the lack of understanding of the nature's laws related to energy distribution applied to fission products, and in part to the current technologic capabilities that make the economical optimum. In order to produce the desired increase of performances a novel multi-scale multi-physics and engineering approach have been developed, starting from the nuclear reactions involved, analyzing in detail the key features and requirements of the 'key players' in the process (neutrons, compound nucleus, fission products, transmutation products, decay radiation), the consequences of their interaction with matter. That complex interaction generates new reactions and new key-players (knock-on electrons, photons, phonons) that further interact with the matter represented by the nuclear fuel, cladding, cooling agents, structural materials and control systems. The understanding of this complexity of problems from fm-ps scale up to macro-system and mitigating all the requirements drives to that desired harmony that provides a safe energy delivery. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Crack Stability in Breached Fuel

This report describes the fracture mechanics formalism to evaluate the stability of cracks in a fuel cladding. Recognized consensus-body linear elastic fracture mechanics (LEFM) was applied to identify the crack instability length, or the length at which unstable mechanical crack extension would occur, as a function of pellet swelling loading (radial strain and fraction conversion from UO 2 to U 3 O 8 ) at the local cracked cladding region for two postulated fracture toughness (K IC ) values of the cladding. The crack opening displacement (COD) and the crack opening area (COA) were also identified. This analysis informs evaluations for crack extension and the potential for pellet debris loss from the fuel rod for cases of pellet oxidation in dry storage canisters where inadvertent residual water may undergo radiolysis causing oxidizing conditions to pellets exposed to the canister environment through breached cladding.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Testing fast reactor fuels in a thermal reactor: Comparison of transmutation metallic fuel alloys behavior by scanning electron microscopy

To optimize nuclear waste repository performance, the destruction of minor actinide elements, particularly Np and Am, in a neutron fast spectrum reactor is possible by incorporating these elements into nuclear fuel. Evaluating the performance of minor actinide containing fuel is of paramount importance to enabling this technology. However, such a task is challenging without an available domestic fast spectrum test reactor. A comparison of fuel performance tested in an available domestic thermal reactor at the Idaho National Laboratory, the Advanced Test Reactor, and in a fast spectrum reactor in France (Phénix) is presented here in this study. This study evaluates the capability of using a cadmium shrouded test position to mimic the power profile along the fuel radius present in fast spectrum reactors so that thermally driven phenomenon (e.g., constituent redistribution) can be evaluated in a thermal reactor and determined to be prototypical of a fast reactor. Thus, optical microscopy and scanning electron microscopy has been performed on irradiated 35U-29Pu-4Am-2Np-30Zr fuel samples (where the number preceding the element is the weight percent concentration) from the two mentioned reactors that present similar irradiation temperatures and power conditions. The results indicate that fuel performance phenomena are reproducible in the two irradiation conditions. The redistribution of Zr occurred in the same manner for the two samples. Similar partitioning of U-Pu-Zr phases was observed, and the behavior of Am was similar in the analyzed specimens. Finally, the overall microstructure evolution seems not to be affected by minor actinides addition compared to expected behavior of conventional U-19Pu-10Zr ternary metal fuels for both specimens. Slight differences in fuel cladding chemical interaction were, however, observed. This difference is likely driven by difference in cladding composition rather than irradiation conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

First-principles study of mechanical properties of zirconium alloys and hydrides

Zirconium alloys have been extensively used as fuel cladding materials in nuclear light water reactors (LWRs) due to their favorable mechanical properties, corrosion resistance, low thermal neutron capture cross section and criticality. Because the main functions of these structural materials are to maintain the integrity of UO{sub 2} fuel rods and prevent the release of fission products into the biosphere, a detailed knowledge of their structural stability is of critical importance to ensure the safe operation of nuclear reactors, and the safety of storage, transportation or disposition of used nuclear fuel assemblies. While the Zr-H phase diagram has been known since the 1950's and has remained largely unchanged, the structures, formation mechanisms, and stability of Zr-hydride phases in pure α-Zr or Zr alloys matrices have been subjects of much debate over the last few decades. The formation of hydride phases in the Zr matrix has been linked in previous studies to the degradation of mechanical properties of Zr/Zr-alloys materials. Therefore, an accurate knowledge of the interplay between the structures, stability and mechanical properties of Zr/Zr-alloys and Zr hydrides is of paramount significance to ensure materials reliability during their in- service lifetime. Despite few first-principles studies have investigated the mechanical stability of Zr hydrides polymorphs proposed so far, no ab initio studies have been carried out, to the best of our knowledge, on the mechanical properties of modern nuclear-grade zirconium alloys such as Zircaloy-4 (Zry-4; 1.2-1.7% Sn), Zirconium low oxidation alloy (ZIRLO; 0.7-1.0% Sn and ∼1.0% Nb), or M5 alloy (0.8-1.2% Nb). Therefore, it is important to carry out a series of first-principles calculations systematically to investigate the structure-property relationship of zirconium hydrides and zirconium alloys, that can help explain differences in elastic properties between high-purity zirconium and nuclear-grade zirconium alloys. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Report on RIA Relevant Modified Burst Testing of ATF Cladding Materials

The mechanical performance of accident-tolerant fuel (ATF) cladding candidates in light-water reactors (LWRs) must be similar to or better than that of current conventional nuclear fuel claddings to reduce dose to the public and ensure a that the core coolable geometry is maintained during a postulated reactivity-initiated accident (RIA) in light-water reactors (LWRs). During an RIA event, the rapid thermal expansion of nuclear fuel can deform the cladding once the fuel–cladding gap closes. In some cases, the pellet–cladding mechanical interaction (PCMI) can induce mechanical failure in ATF candidates. Thus, the mechanical response of ATF cladding must be investigated by mimicking the conditions of RIA and potentially performing Transient Reactor Test (TREAT) experiments to establish or verify the safety envelope. The work presented in this report investigated the failure behavior of as-received, hydrided, and chromium-coated (Cr-coated) Zircaloy-4 (Zry-4) cladding tube under strain-driven mechanical conditions, mimicking postulated RIA loading conditions. Mechanical testing was performed at 300°C via modified burst test (MBT) equipment with pulse width control previously developed under the Department of Energy’s (DOE’s) Advanced Fuel Campaign (AFC). The mechanical strains were determined using 2D digital image correlation (DIC) techniques. The base Zry-4 acquired by Cameco Inc. was in stress-relieved annealed (SRA) condition. Because of the observed large deformation of the cladding tubes, the failure strain definition was updated for the MBT, which can also be applied to other tube tests where significant bulging (out-of-plane deformation) is present. The failure strain was determined to be affected by the speed of the test or the RIA event. As the RIA-like event duration decreased from 75 to 15 ms, the failure strain decreased 5, 7 and 1% for as-received, hydrided, and Cr-coated specimens, respectively. Fractography on the Cr-coated specimens indicated the presence of two failure mechanisms: (i) crenulation at the outer surface of the coating due to the tensile tractional forces along with coatings grain microstructure and (ii) formation of critical defect at the coating/cladding interface that initiated coating rupture after severe plastic deformation of the Zry- 4 substrate. Based on the MBT results and fractography observations, performing mechanical property testing at high strain rates—in particular on Cr-coated tubes—and semi-integral TREAT experiments are required future efforts to ensure ATF cladding performance during transients. The testing recommended would also inform the development of long-term generalized cladding technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗