Search NASA⌕ Search

SEARCH · Search NASA

Results for “Marginal Distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

The role of the margins in ice stream dynamics

At first glance, it would appear that the bed of the active ice stream plays a much more important role in the overall force balance than do the margins, especially because the ratio of the half-width to depth for a typical ice stream is large (15:1 to 50:1). On the other hand, recent observations indicate that at least part of the ice stream is underlain by a layer of very weak till (shear strength about 2 kPa), and this weak basal layer would then imply that some or all of the resistive drag is transferred to the margins. In order to address this question, a detailed velocity profile near Upstream B Camp, which extends from the center of the ice stream, across the chaotic shear margin, and onto the Unicorn, which is part of the slow-moving ice sheet was measured. Comparison of this observed velocity profile with finite-element models of flow shows several interesting features. First, the shear stress at the margin is on the order of 130 kPa, while the mean value along the bed is about 15 kPa. Integration of these stresses along the boundaries indicates that the margins provide 40 to 50 percent, and the bed, 60 to 40 percent of the total resistive drag needed to balance the gravitational driving stress in this region. (The range of values represents calculations for different values of surface slope.) Second, the mean basal stress predicted by the models shows that the entire bed cannot be blanketed by the weak till observed beneath upstream B - instead there must be a distribution of weak till and 'sticky spots' (e.g., 85 percent till and 15 percent sticky spots of resistive stress equal to 100 kPa). If more of the bed were composed of weak till, then the modeled velocity would not match that observed. Third, the ice must exhibit an increasing enhancement factor as the margins are approached (E equals 10 in the chaotic zone), in keeping with laboratory measurements on ice under prolonged shear strain. Also, there is either a narrow zone of somewhat stiffer ice (E equals 5) outward of the shear margin, or the bed is frozen there. And last, the high shear stress and strain rate found at the margin are likely to cause significant viscous heating (q) in the marginal ice. The increase in temperature is proportional to qX/u, where X is the width of the shear zone and u is the transverse velocity component bringing cold ice in from the ice sheet outside the shear zone. Near upstream B, this heating is likely to cause an increase in temperature of 4 to 10 K. Plans are to measure this temperature increase in a series of bore holes near the margin during the 1992-93 field season, as well as to provide a more detailed description of the velocity field there.

Echelmeyer, Keith↗

SU-E-T-354: Peak Temperature Ratio of TLD Glow Curves to Investigate the Spatial Dependence of LET in a Clinical Proton Beam

Purpose: Use the ratio of the two high temperature peaks (HTR) in TLD 700 glow curves to investigate spatial dependence of the linear energy transfer (LET) in proton beams. Studies show that the relative biological effectiveness (RBE) depends upon the physical dose as well as its spatial distribution. Although proton therapy uses a spatially invariant RBE of 1.1, studies suggest that the RBE increases in the distal edge of a spread out Bragg peak (SOBP) due to the increased LET. Methods: Glow curve studies in TLD 700 show that the 280 C temperature peak is more sensitive to LET radiation than the 210 C temperature peak. Therefore, the areas under the individual temperature peaks for TLDs irradiated in a proton beam normalized to the peak ratio for 6 MV photons are used to determine the HTR to obtain information on its LET. TLD 700 chips with dimensions 0.31×0.31×0.038 cc are irradiated with 90 MeV protons at varying depths in a specially designed blue wax phantom to investigate LET spatial dependence. Results: Five TLDs were placed at five different depths of the percent depth dose curve (PDD) of range 16.2 cm: center of the SOPB and approximately at the 99% distal edge, 90%, 75% and 25% of the PDD, respectively. HTR was 1.3 at the center of the SOBP and varied from 2.2 to 3.9 which can be related to an LET variation from 0.5 to 18 KeV/μ via calibration with radiation beams of varying LET. Conclusion: HTR data show a spatially invariant LET slightly greater than the 6 MV radiations in the SOBP, but a rapidly increasing LET at the end of the proton range. These results indicate a spatial variation in RBE with potential treatment consequences when selecting treatment margins to minimize the uncertainties in proton RBE.

07 ISOTOPE AND RADIATION SOURCES↗

SU-E-J-64: Feasibility Study of Surgical Clips for Fiducial Tracking in CyberKnife System

Purpose: To investigate the ability of CyberKnife to track surgical clips used as fiducial markers. Methods: The Octavius 1000SRS detector and solid water (RW3) slab phantom were used with motion platform to evaluate the study. The RW3 slab phantom was set up to measure the dose distribution from coronal plane. It consists of 9 plates and the thickness of each plate is 10mm. Among them, one plate was attached with 3 surgical clips, which are orthogonally positioned on outer region of array. The length of attached clip was represented as 1cm on planning CT. The clip plate was placed on the 1000SRS detector and 3 slabs were stacked up on the plate to build the measuring depth. Below the detector, 5 slabs were set. The two-axis motion platform was programmed with 1D sinusoidal movement (20mm peak-to-peak, 3s period) toward superior/inferior and left/right directions to simulate target motion. During delivery, two clips were extracted by two X-ray imagers, which led to translational error correction only. Synchrony was also used for dynamic tracking. After the irradiation, the measured dose distribution of coronal plane was compared with the planar dose distribution calculated by the CyberKnife treatment planning system (Multiplan) for cross verification. The results were assessed by comparing the absolute Gamma (γ) index. Results: The dose distributions measured by the 1000SRS detector were in good agreements with those calculated by Multiplan. In the dosimetric comparison using γ-function criteria based on the distance-to-agreement of 3mm and the local dose difference of 3%, the passing rate with γ- parameter ≤1 was 91% in coronal plane. Conclusion: The surgical clips can be considered as new fiducials for robotic radiosurgery delivery by considering the target margin with less than 5mm.

60 APPLIED LIFE SCIENCES↗

Discovery and analysis of low-surface-brightness galaxies in the environment of NGC 1052

The environment of NGC 1052 has recently attracted much attention because of the presence of low-surface-brightness galaxies (LSBGs) with apparently “exotic” properties, making it a region of high interest for the detection of new objects. Here, we used public deep photometric data from the Dark Energy Camera Legacy Survey to carry out a comprehensive search for LSBGs over a wide region of 6 × 6 degrees, equivalent to 2 × 2 Mpc at the distance of NGC 1052. We detected 42 LSBGs with r eff > 5 arcsec and μ g (0) > 24 mag arcsec -2 , of which 20 are previously undetected objects. Among all the newly detected objects, RCP 32 stands out with extreme properties: r eff = 23.0 arcsec and $\langle$μ g $\rangle$ eff = 28.6 mag arcsec -2 . This makes RCP 32 one of the lowest surface brightness galaxies ever detected through integrated photometry, located at just 10 arcmin from the extensively studied NGC 1052-DF2. We explored the presence of globular clusters (GCs) in the LSBGs. We marginally detected a GC system in RCP 32, and argue that this LSBG is of great interest for follow-up observations given its extremely low baryon density. After analyzing the distribution of galaxies with available spectroscopy, we identified a large-scale structure of approximately 1 Mpc that is well isolated in redshift space and centered on NGC 1052. The spatial correlation analysis between the LSBGs and this large-scale structure suggests their association. However, when exploring the distribution of effective radius, we find an overpopulation of large LSBGs (r eff > 15 arcsec) located close to the line of sight of NGC 1052. We argue that this is suggestive of a substructure with similar radial velocity in sight projection, but at a closer distance, to which some of these apparently larger LSBGs could be associated. However, possible effects derived from tidal interactions are worthy of further study. Our work expands the catalog of LSBGs with new interesting objects and provides a detailed environmental context for the study of LSBGs in this region.

79 ASTRONOMY AND ASTROPHYSICS↗

Toroidal configurations of perfect fluid in the Reissner-Nordström-(anti-)de Sitter spacetimes

Influence of cosmological constant on toroidal fluid configurations around charged spherically symmetric black holes and naked singularities is demostrated by study of perfect-fluid tori with uniform distribution of specific angular momentum orbiting in the Reissner-Nordström-(anti-)de Sitter spacetimes. Toroidal configurations are allowed only in the spacetimes admitting existence of stable circular geodesics. Configurations with marginally closed equipotential (equipressure) surfaces crossing itself in a cusp allow accretion (through the inner cusp) and/or excretion (through the outer cusp) of matter from the toroidal configuration. Detailed classification of the Reissner-Nordström-(anti-)de Sitter spacetimes according to properties of the marginally stable tori is given. It is demonstrated that in the Reissner-Nordström-de Sitter naked-singularity spacetimes an interesting phenomenon of doubled tori can exist enabling exchange of matter between two tori in both inward and outward directions. In naked-singularity spacetimes the accretion onto the central singularity is impossible due to existence of a potential barrier.

79 ASTRONOMY AND ASTROPHYSICS↗

Analysis of Distributed Energy Storage as a Core Grid Infrastructure via Production Cost Modeling

Energy storage plays a pivotal role in enabling power system operation with more flexibility and resilience. Unlike current practice that considers energy storages as attached ancillary devices, this paper focuses on storages as a core infrastructure by looking at their spatial distribution in the system. A sensitivity analysis based on production cost modeling is conducted to demonstrate the benefits of distributed energy storages. First, the modeling of energy storages in production cost modeling is presented. Second, potential optimal locations of distributed energy storages in a power system are discussed. Finally, multiple scenarios with various numbers and locations of additional distributed energy storages in the WECC 2030 model are created. The production cost modeling results of these scenarios show that distributed energy storages have higher utilization compared to the centralized ES units and therefore provide significantly more benefits in terms of reduction in generation cost, emission cost, and volatility of location marginal prices. A saturation effect is observed suggesting the selection of optimal locations will further improve the benefits.

Nguyen, Quan H.↗

System level comparison of FDMA vs. CDMA (under conference guideline constraint)

The margin that is required to mitigate the near-far problem in a Code Division Multiple Access (CDMA) mobile satellite system is determined by the radio-propagation model selected, the distribution of the users in clear and shadowed environments, and implementation techniques. The use of revenue potential as a means of evaluating the relative merits of CDMA and Frequency Division Multiple Access (FDMA) systems is a convenient way to rationalize the performance of systems using high-gain and low-gain antennas. The revenue potential of CDMA is much greater than the revenue potential for FDMA for a particular satellite design considered.

Renshaw, Ken↗

Radial Surface Density Profiles of Gas and Dust in the Debris Disk Around 49 Ceti

We present approximately 0".4 resolution images of CO(3-2) and associated continuum emission from the gas-bearing debris disk around the nearby A star 49 Ceti, observed with the Atacama Large Millimeter/Submillimeter Array (ALMA). We analyze the ALMA visibilities in tandem with the broadband spectral energy distribution to measure the radial surface density profiles of dust and gas emission from the system. The dust surface density decreases with radius between approximately 100 and 310 au, with a marginally significant enhancement of surface density at a radius of approximately 110 au. The SED requires an inner disk of small grains in addition to the outer disk of larger grains resolved by ALMA. The gas disk exhibits a surface density profile that increases with radius, contrary to most previous spatially resolved observations of circumstellar gas disks. While approximately 80% of the CO flux is well described by an axisymmetric power-law disk in Keplerian rotation about the central star, residuals at approximately 20% of the peak flux exhibit a departure from axisymmetry suggestive of spiral arms or a warp in the gas disk. The radial extent of the gas disk (approx. 220 au) is smaller than that of the dust disk (approx. 300 au), consistent with recent observations of other gasbearing debris disks. While there are so far only three broad debris disks with well characterized radial dust profiles at millimeter wavelengths, 49 Ceti's disk shows a markedly different structure from two radially resolved gas-poor debris disks, implying that the physical processes generating and sculpting the gas and dust are fundamentally different.

Atacama Large Millimeter Submillimeter Array(ALMA)↗

Destabilizing Effect of Dynamical Friction on Fast-Particle-Driven Waves in a Near-Threshold Nonlinear Regime

The nonlinear evolution of waves excited by the resonant interaction with energetic particles, just above the instability threshold, is shown to depend on the type of relaxation process that restores the unstable distribution function. When dynamical friction dominates over diffusion in the phase space region surrounding the wave-particle resonance, an explosive evolution of the wave is found to be the only solution. This is in contrast with the case of dominant diffusion when the wave may exhibit steady-state, amplitude modulation, chaotic and explosive regimes near marginal stability. The experimentally observed differences between Alfvenic instabilities driven by neutral beam injection and those driven by ion-cyclotron resonance heating are interpreted.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Direct mechanical energy measures of hammer mill comminution of switchgrass, wheat straw, and corn stover and analysis of their particle size distributions

Biomass particle size impacts handling, storage, conversion, and dust control systems. Size reduction mechanical energy was directly measured for switchgrass (Panicum virgatum L.), wheat straw (Triticum aestivum L.), and corn stover (Zea mays L.) in an instrumented hammer mill. Direct energy inputs were determined for hammer mill operating speeds from 2000 to 3600 rpm for 3.2 mm integral classifying screen and mass input rate of 2.5 kg/min with 90 - and 30 -hammers. Overall accuracy of specific energy measurement was calculated as 0.072 MJ/Mg. Particle size distributions created by hammer mill were determined for mill operating factors using ISO sieve sizes from 4.75 to 0.02 mm in conjunction with Ro-Tap sieve analyzer. A wide range of analytical descriptors were examined to mathematically represent the range of particle sizes in the distributions. Total specific energy (MJ/Mg) was defined as size reduction energy to operate the hammer mill plus that imparted to biomass. Effective specific energy was defined as energy imparted to biomass. Total specific energy for switchgrass, wheat straw, and corn stover grinding increased by 37, 30, and 45% from 114.4, 125.1, and 103.7 MJ/Mg, respectively, with an increase in hammer mill speed from 2000 to 3600 rpm for 90 -hammers. Corresponding total specific energy per unit size reduction was 14.9, 19.7, and 13.5 MJ/Mg mm, respectively. Effective specific energy of 90 -hammers decreased marginally for switchgrass and considerably for wheat straw and it increased for corn stover with an increase in speed from 2000 to 3600 rpm. However, effective specific energy increased with speed to a certain extent and then decreased for 30 -hammers. Rosin Rammler equation fitted the size distribution data with R2 > 0.995. Mass relative span was greater than 1, which indicated a wide distribution of particle sizes. Hammer milling of switchgrass, wheat straw, and corn stover with 3.2 mm screen resulted in well-graded fine-skewed mesokurtic particles. Uniformity coefficient was < 4.0 for wheat straw, which indicated uniform mix of particles, and it was about 4.0 for switchgrass and corn stover, which indicated a moderate assortment of particles. Size-related parameters, namely, geometric mean diameter, Rosin Rammler size parameter, median diameter, and effective size had strong correlation among themselves and good negative correlation with speed. Distribution-related parameters, namely, Rosin Rammler distribution parameter, mass relative span, inclusive graphic skewness, graphic kurtosis, uniformity index, uniformity coefficient, coefficient of gradation and distribution geometric standard deviation had strong correlation among themselves and a weak correlation with mill speed. Results of this extensive analysis of specific energy and particle sizes can be applied to selection of hammer mill operating factors to produce a particular size of switchgrass, wheat straw, and corn stover grind, and will serve as a guide for relations among the energy and various analytic descriptors of biomass particle distributions.

09 BIOMASS FUELS↗

Measurement of primordial non-Gaussianity using the WMAP 5-year temperature skewness power spectrum

We constrain the primordial non-Gaussianity parameter of the local model f{sub NL} using the skewness power spectrum associated with the two-to-one cumulant correlator of cosmic microwave background temperature anisotropies. This bispectrum-related power spectrum was constructed after weighting the temperature map with the appropriate window functions to form an estimator that probes the multipolar dependence of the underlying bispectrum associated with the primordial non-Gaussianity. We also estimate a separate skewness power spectrum sensitive more strongly to unresolved point sources. When compared to previous attempts at measuring the primordial non-Gaussianity with WMAP data, our estimators have the main advantage that we do not collapse information to a single number. When model fitting the two-to-one skewness power spectrum, we make use of bispectra generated by the primordial non-Gaussianity, radio point sources, and lensing-secondary correlation. We analyze Q, V, and W-band WMAP 5-year data using the KQ75 mask out to l{sub max}=600. Using V and W-band data and marginalizing over model parameters related to point sources and lensing-secondary bispectrum, our overall and preferred constraint on f{sub NL} is 11.0{+-}23.7 at the 68% confidence level (-36.4<f{sub NL}<58.4 at 95% confidence). We find no evidence for a nonzero value of f{sub NL} even marginally at the 1{sigma} level.

99 GENERAL AND MISCELLANEOUS↗

Optimization and Control of Electric Power Systems

The analysis and optimization needs for planning and operation of the electric power system are challenging due to the scale and the form of model representations. The connected network spans the continent and the mathematical models are inherently nonlinear. Traditionally, computational limits have necessitated the use of very simplified models for grid analysis, and this has resulted in either less secure operation, or less efficient operation, or both. The research conducted in this project advances techniques for power system optimization problems that will enhance reliable and efficient operation. The results of this work appear in numerous publications and address different application problems include optimal power flow (OPF), unit commitment, demand response, reliability margins, planning, transmission expansion, as well as general tools and algorithms.

24 POWER TRANSMISSION AND DISTRIBUTION↗

SU-E-T-450: Dosimetric Impact of Rotational Error On Multiple-Target Intensity-Modulated Radiosurgery (IMRS) with Single-Isocenter

Purpose: Evaluating the dosimetric-impact on multiple-targets placed away from the isocenter-target with varying rotational-error introduced by initial setup uncertainty and/or intrafractional-movement Methods: CyberKnife-Phantom was scanned with the Intracranial SRS-protocol of 1.25mm slice-thickness and the multiple-targets(GTV) of 1mm and 10mm in diameter were contoured on the Eclipse. PTV for distal-target only was drawn with 1mm expansion around the GTV to find out how much margin is needed to compensate for the rotational-error. The separation between the isocenter-target and distal-target was varied from 3cm to 7cm. RapidArc-based IMRS plans of 16Gy single-fraction were generated with five non-coplanar arcs by using Varian TrueBeam-STx equipped with high resolution MLC leaves of 2.5mm at center and with dose-rate of 1400MU/min at 6MV for flatteringfilter- free(FFF). An identical CT image with intentionally introduced 1° rotational-error was registered with the planning CT image, and the isodose distribution and Dose-Volume-Histogram(DVH) were compared with the original plans. Additionally, the dosimetric-impact of rotational error was evaluated with that of 6X photon energy which was generated with the same target-coverage. Results: For the 1mm-target with 6X-FFF, PTV-coverage(D100) of the distal-target with 1° rotational-error decreased from 1.00 to 0.35 as the separation between isocenter-target and distal-target increased from 3cm to 7cm. However, GTV-coverage(D100) was 1.0 except that of 7cm-separation(0.55), which resulted from the 1mm-margin around the distal-target. For 6X photon, GTV-coverage remained at 1.0 regardless of the separation of targets, showing that the dosimetric-impact of rotational error depends on the degree of rotational-error, separation of targets, and dose distribution around targets. For 10mm-target, PTV-coverage of distaltarget located 3cm-away was better than that of 1mm-target(0.93 versus 0.7) and GTV-coverage was 1.0 regardless of 6X-FFF/6X photon beams. Conclusion: RapidArc-based Multiple-target IMRS may Resultin a compromised outcome due to the setup-error for distal-targets. With 1mm-margin, GTV-coverage of distal-target was 1.0 although the separation of targets was up to 5cm.

07 ISOTOPE AND RADIATION SOURCES↗

Solar wind magnetic fluctuations and electron non-thermal temperature anisotropy: survey of Wind-SWE-VEIS observations

The solar wind electron velocity distribution function (eVDF) exhibits a variety of non-thermal features that deviate from thermal equilibrium. These deviations from equilibrium provide a local source for electromagnetic fluctuation emissions, including the commonly observed electron whistler-cyclotron and firehose instabilities. We present a systematic analysis of Wind-SWE-VEIS observations of solar wind electron plasma and associated Wind-MFI observed magnetic fluctuations. For the first time using the full solar wind electron distribution and its moments, without separation of the various electron components, we show clear evidence that the temperature anisotropy threshold of the parallel electron cyclotron anisotropic instability bounds solar wind electrons during slow solar wind periods. We also demonstrate that during periods of slow solar wind, collisions—while infrequent—are the dominant mechanism by which solar wind electrons are constrained, leading to isotropization. During fast solar wind periods, magnetic fluctuations and solar wind anisotropies are enhanced above the parallel whistler anisotropic threshold boundary and collisional effects are significantly reduced. Preliminary calculations further show that the oblique electron whistler mirror anisotropic instability bounds both the slow and fast solar wind. Regardless of speed, the solar wind electron thermal anisotropy appears globally bounded by the parallel electron firehose instability for anisotropies T{sub e⊥}/T{sub e||}<1. Our results indicate that collisions, while infrequent, play a necessary role in regulating the solar wind eVDFs. In striking contrast to solar wind ions, solar wind electron plasma, when considered globally as a single eVDF, is only marginally stable with respect to parallel propagating instabilities.

79 ASTRONOMY AND ASTROPHYSICS↗

Formation and Evolution of the Disk System of the Milky Way: [alpha/Fe] Ratios and Kinematics of the SEGUE G-Dwarf Sample

We employ measurements of the [{alpha}/Fe] ratio fromlow-resolution (R {approx} 2000) spectra of 17,500 G-type dwarfs included in SDSS Data Release 8, selected using simple and well-understood selection criteria, to separate them into likely thin- and thick-disk subsamples. This classification, based on chemistry, is strongly motivated by the bi-modal distribution of stars in the [{alpha}/Fe] vs. [Fe/H] diagram. The resulting subsamples allow, for the first time, investigations of the kinematic behavior of thin- and thick-disk stars as a function of metallicity and position up to distances of 3 kpc from the Galactic plane. Both subsamples exhibit strong gradients of orbital rotational velocity with metallicity, but with opposite signs (-20 to -30 km s{sup -1} dex{sup -1} for the thin-disk population, and +40 to +50 km s{sup -1} dex{sup -1} for the thick-disk population). We find that the rotational velocity decreases with the distance from the plane for both disk components, with similar slopes (10 km s{sup -1} kpc{sup -1}), and a nearly constant difference in the mean rotational velocity of about 30 km s{sup -1}. The mean rotational velocity is uncorrelated with Galactocentric distance for the thin-disk subsample, and exhibits only a marginally significant correlation for the thick-disk subsample. Thick-disk stars exhibit a very strong trend of orbital eccentricity with metallicity (-0.2 dex{sup -1}), while the eccentricity does not change with metallicity for the thin-disk subsample. The eccentricity is almost independent of Galactocentric radius for the thin-disk stars, while a marginal gradient of the eccentricity with distance exists for the thick-disk population. Both subsamples possess similar trends of increasing eccentricity with distance from the Galactic plane, with a constant difference of about 0.1. The shapes of the overall distributions of orbital eccentricity for the thin- and thick-disk populations are quite different from one another, independent of distance from the plane; neither subsample has significant numbers of stars with eccentricity above 0.6. These observational results provide strong new constraints on models for the formation and evolution of the Milky Way's disk system. For example, the observed dependence of the mean rotational velocity on metallicity for thin-disk stars is inconsistent with predictions from classical local chemical evolution models. We also consider the predictions of several contemporary models of disk evolution, such as radial migration, gas-rich mergers, disk heating, and pure accretion models. We find that radial migration appears to have played an important role in the evolution of the thin-disk population, but possibly less so, relative to the gas-rich merger or disk heating scenarios, for the thick disk. Pure accretion models appear to be ruled out by the observed distribution of eccentricities for thick-disk stars. We emphasize that more physically realistic models, and simulations that probe a greater range of disk formation scenarios, need to be constructed in order to carry out the detailed quantitative comparisons that our new data enable.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Cryogenic System Preliminary Design for a 0.5m-Long, Conduction-Cooled Nb3Sn Undulator Magnet Prototype

There are several NbTi superconducting undulator (SCU) magnets currently in operation at the Advanced Photon Source (APS) at Argonne National Laboratory (ANL). The development on Nb3Sn-based superconducting undulator magnets at APS is underway due to the potential to further enhance the performance of the SCUs. Superconducting undulator magnets need to keep temperature gradients minimized in order to retain thermal and operating current margin. We have designed the thermal links for efficient heat conduction using 3D finite element analysis (FEA) simulation in COMSOL Multiphysics software, which was later used for the calculation of the temperature distribution across a 0.5 m long, conduction-cooled, Nb3Sn undulator magnet prototype that includes both conductive heat transfer and radiative heating components. We have modelled the evolution of the thermal properties of the magnet winding as well as other cold parts during cool-down from ambient temperature with the operation of a SHI RDK-415D cryocooler to examine the estimated time that is needed for the cooldown as well as the baseline temperature we could achieve. A key result was that a maximum coil delta T = 0.11 K along the designed thermal links and a temperature range of 3.42 K-3.53 K for the winding were predicted at steady state. A pair of G10 support rods for carrying the magnet as well as a pair of current leads made of metals were also designed and optimized for the testing system, targeting for an operation temperature of 4 K and a coil current of 950 A DC.

Zhang, Danlu↗

Landscape responses to intraplate deformation in the Kalahari constrained by sediment provenance and chronology in the Okavango Basin

The structural depression that occupies the Okavango Basin in southern Africa comprises a depo-centre within the intracratonic Kalahari Basin where sediments of the Cenozoic Kalahari Group have accumulated. The Okavango Basin has been formed due to stretching and subsidence at an area of diffused deformation, southwestwards to the main East African Rift System (EARS). Sediments from two full Kalahari Group sequences, located on opposite sides of the Gumare Fault that forms a major fault within the Okavango Basin, were studied to determine their provenance and chronology. Terrestrial Cosmogenic Nuclide (TCN) 26 Al/ 10 Be burial dating was used to constrain a chronostratigraphical framework, and Pb, Sr, and Nd isotopic ratios combined with geochemical and sedimentological analyses were applied to track the source areas of the sediments.Results indicate the following sequence of basin filling: (a) Accumulation between ca. 4–3 Ma during which the currently downthrown (southern) block received a mixture of sediments mostly from the Choma-Kalomo, Ghanzi-Chobe, and Damara terranes, and possibly from the Lufilian Belt and/or Karoo basalts during earlier stages of deposition. Simultaneously, the upthrown (northern) block received sediments from more distant Archean sources in the Zimbabwe and/or Kasai cratons, (b) Hiatus in sedimentation occurred at both sites between ca. 3–2 Ma, (c) Sediments on both sides of the Gumare Fault share a similar source (Angolan Shield) with minor distinct contributions to the downthrown block from the Kasai Craton and local sources input to the upthrown block, and (d) Regional distribution of aeolian sand since at least 1 Ma. The change in source areas is attributed to rearrangements of the drainage systems that were probably linked to vertical crustal movements on the margins of the Okavango Basin. The tectonically induced morphodynamics controlled the landscape evolution of the endorheic basin where vast lakes, wetlands and salt pans have developed through time.

58 GEOSCIENCES↗

Cambium 2023 Scenario Descriptions and Documentation

The National Renewable Energy Laboratory's (NREL's) Cambium data sets are annually released sets of simulated hourly emission, cost, and operational data for a range of modeled futures of the U.S. electric sector with metrics designed to be useful for long-term decision- making. The 2023 Cambium data set is the fourth annual release. The data sets are a companion product to NREL's Standard Scenarios, which are likewise released annually and are a set of projections of how the U.S. electric sector could evolve across a suite of different potential futures, but covering more scenarios with less temporal granularity (Gagnon et al. 2024). Information about Cambium and related publications can be found at https://www.nrel.gov/analysis/cambium.html, and the Cambium data sets can be viewed and downloaded at https://scenarioviewer.nrel.gov/. In this documentation, we describe Cambium 2023's scenarios, define the metrics, and document the Cambium-specific methods for calculating those metrics.

24 POWER TRANSMISSION AND DISTRIBUTION↗