Search NASA⌕ Search

SEARCH · Search NASA

Results for “Novel Characterization Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

BACKFLIP: A Comparison of Emerging Non-Fluoropolymer-Based, Co-Extruded PV Backsheets to Industry-Benchmark Technologies

As the photovoltaic (PV) industry is rapidly expanding around the world, there has been an increasing interest in extending the lifespan of PV modules. Concern has also emerged regarding the recyclability of modules and their component materials, including fluoropolymer-based backsheets. Laminated polyethylene-terephthalate (PET) core backsheets have traditionally been used in the PV industry, but new, co-extruded polyolefin (PO) backsheets show promise as an improved alternative. Mini-module and coupon samples of seven different backsheets (made of layers including contemporary PET and fluoropolymers, novel PO, and polyamide (PA) materials) were run through hygrometric- or UV photolytic-accelerated aging to identify and better understand each material’s degradation modes and the backsheets’ field reliability. In addition to the artificial aging, the natural weathering methods used in this study are described. The comprehensive set of chemical, mechanical, and structural characterizations at intermittent read points in this study is presented, including: visual appearance and color; gloss; mechanical tensile testing; I-V performance; electroluminescence (EL) imaging; dielectric breakdown; FTIR-chemical structure; X-ray-polymer structure (WAXS); and DSC-crystalline content. After 4000 h of aging, a strong correlation occurs between initial physical characteristics (mechanical tensile test) and operating performance (EL and I-V characteristics).

41 EE - Solar Energy Technologies Office (EE-4S)↗

BACKFLIP: A Comparison of Emerging Non-Fluoropolymer-Based, Co-Extruded PV Backsheets to Industry-Benchmark Technologies

As the photovoltaic (PV) industry is rapidly expanding around the world, there has been an increasing interest in extending the lifespan of PV modules. Concern has also emerged regarding the recyclability of modules and their component materials, including fluoropolymer-based backsheets. Laminated polyethylene-terephthalate (PET) core backsheets have traditionally been used in the PV industry, but new, co-extruded polyolefin (PO) backsheets show promise as an improved alternative. Mini-module and coupon samples of seven different backsheets (made of layers including contemporary PET and fluoropolymers, novel PO, and polyamide (PA) materials) were run through hygrometric- or UV photolytic-accelerated aging to identify and better understand each material's degradation modes and the backsheets' field reliability. In addition to the artificial aging, the natural weathering methods used in this study are described. The comprehensive set of chemical, mechanical, and structural characterizations at intermittent read points in this study is presented, including: visual appearance and color; gloss; mechanical tensile testing; I-V performance; electroluminescence (EL) imaging; dielectric breakdown; FTIR-chemical structure; X-ray-polymer structure (WAXS); and DSC-crystalline content. After 4000 h of aging, a strong correlation occurs between initial physical characteristics (mechanical tensile test) and operating performance (EL and I-V characteristics). This presentation focuses on gloss, FTIR, and breakdown voltage measurements. Results for MiMo power, grayness from EL imaging, optical micrscopy, and specimen morphology (on extraction when cut from MiMos) is also presented.

backsheet↗

Physical characterization of High Entropy Alloys through Differential Scanning Calorimetry and Nanoindentation

In recent years several accelerator facilities have been limiting their beam power output not due to constraint of the accelerators but by concerns on the survivability of their targets, which in turn has led to R&D efforts into new, more resistant materials. One of these novel materials are High Entropy Alloys, the main focus of the internship project. This paper details the activities performed during the CCI 10-week internship by the authors, as well as to discuss the results obtained from said internship. The project consisted of the physical characterization of 12 batches of High Entropy Alloys (HEAs); the methods used to analyze the materials were Nanoindentation, which allows to determine the elastic modulus of the material and its hardness, and Differential Scanning Calorimetry (DSC), allowing the determination of specific heat.

Pacheco Uribe, Rene↗

Advanced Characterization Capabilities for Nuclear Materials via Nuclear Science User Facilities (NSUF)

Advanced post-irradiation examination (PIE) techniques are required to design new or improved nuclear materials, characterize, and understand in-core behavior of fuel and materials, and support the qualification of new reactor materials. The Nuclear Science User Facilities (NSUF) is the U.S. Department of Energy Office of Nuclear Energy's only designated nuclear science user facility. NSUF provides researchers access to PIE capabilities at Idaho National Laboratory and at a diverse mix of university, national laboratory and industrial partner institutions. The PIE capabilities include novel destructive and non-destructive techniques for radiation damage characterization, such as advanced diffraction techniques (X-ray, electron, or neutron) coupled to extreme environments; in-situ observation of microstructural evolution under irradiation; in-situ irradiation to monitor corrosive attack in coolant environments; in-situ irradiation and mechanical testing; and test methods for synergistic effects of superimposed extreme environments (temperature, irradiation, stress, corrosion) on materials behaviors. This talk will provide an overview of NSUF PIE capabilities.

36 MATERIALS SCIENCE↗

Systems, methods and tools for subterranean electrochemical characterization and enthalpy measurement in geothermal reservoirs

The present disclosure is directed to systems, methods and tools that measure ionic concentrations and downhole enthalpy of a flowing geothermal fluid in real-time at high-temperature and pressure. The systems, methods and tools include measuring the concentration of selected naturally occurring ions found in the liquid phase of the geothermal fluid throughout the wellbore using novel electrochemical sensor technologies. The change in liquid-phase ion concentration will be used to calculate the proportion of liquid to steam and allow for accurate enthalpy measurements. The techniques and technologies described here can be applied to any application of electrochemical sensing in extreme environments.

Cieslewski, Grzegorz↗

Time-dependent behavioral data from zebrafish reveals novel signatures of chemical toxicity using point of departure analysis

High-content imaging of embryonic zebrafish behavior can be used as a screening approach to rapidly evaluate the relative potential for chemicals to cause toxicity. However, most statistical methods applied to these data so far transform movement values to incidence-based “hits” and calculate lowest effect levels (LELs), which loses individual fish resolution of behavior and defies hazard ranking due to reliance on applied dose levels. Here, we have developed and parallelized a workflow to calculate benchmark dose (BMD) values from dynamic, high-content zebrafish behavior data that scales for high-throughput chemical screening. To appropriately capture the dynamics of zebrafish response from light to dark stimulus, we summarized time-dependent data using both area under the curve and immediate change at the transition point into two novel metrics that characterized abnormal behavior as a function of chemical concentration. The BMD workflow was applied to calculate BMD 10 values of 1,060 ToxCast chemicals for 24 zebrafish endpoints, including behavior, mortality and morphology. The BMD 10 values provided better precision and separation than LELs for clustering chemicals since they were derived from models that best-fit their concentration-response curves. Clustering analysis revealed behavioral signatures as the most sensitive endpoints. High concordance in chemical activity was observed between ToxCast assays and zebrafish behavioral endpoints, however ToxPi analysis indicated that rankings based on in vitro data was not a reliable predictor of in vivo rankings for lower potency chemicals. The methods developed in this work will enable the use of high-content zebrafish behavioral screening data for BMD analysis in toxicological hazard assessment.

59 BASIC BIOLOGICAL SCIENCES↗

Towards Synthesis, Characterization and Properties of Smart Material Based on Chitosan Using Mn-IV Itaconic Acid as a Novel Redox Pair

The precipitation technique of Mn-IV/itaconic acid redox pair was chosen for grafting meth acrylic acid onto chitosan. This was done to maximize the graft yield and minimize the homopolymer formation to lower extent in addition to prepare water soluble chitosan instead of non-eco friendly acid soluble one. Evidence of grafting was confirmed instrumentally by (FTIR, SEM, and TGA), titrimetrically using carboxyl content and gravimetrically using dry weight method. The mechanism of grafting and factors affected grafting reaction were studied in details, and the optimum reaction conditions were obtained at [chitosan] 2 g, [MnO{sub 2}] 25.9 mmol/100 g sample, [itaconic acid],100 mmol/L, [MAA] 50% bows,[liquor ratio], 25, reaction time, 2 h, and [reaction temperature], 65 °C. It is also seen from the obtained results that, the resultant copolymer showed the following findings: (a) only nitric acid solutions are proved to be a superior solvent for the grafted product; (b) superabsorbent towards water (197 g H{sub 2}O/g polymer) and saline absorbency (60 g saline solution/g polymer) after cross-linked with epichlorohydrin, (c) higher water solubility (21%) at 48% graft yield and (d) 73.5% copper ion removal in comparison with 41% for chitosan.

36 MATERIALS SCIENCE↗

Solid State Characterizations of Long-Term Leached Cast Stone Monoliths

This report describes the results from the solid phase characterization of six Cast Stone monoliths from the extended leach tests recently reported on (Serne et al. 2016),that were selected for characterization using multiple state-of-the-art approaches. The Cast Stone samples investigated were leached for > 590 d in the EPA Method 1315 test then archived for > 390 d in their final leachate. After reporting the long term leach behavior of the monoliths (containing radioactive 99 Tc and stable 127 I spikes and for original Westsik et al. 2013 fabricated monoliths, 238 U), it was suggested that physical changes to the waste forms and a depleting inventory of contaminants of potential concern may mean that effective diffusivity calculations past 63 d should not be used to accurately represent long-term waste form behavior. These novel investigations, in both length of leaching time and application of solid state techniques, provide an initial arsenal of techniques which can be utilized to perform such Cast Stone solid phase characterization work, which in turn can support upcoming performance assessment maintenance. The work was performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to characterize several properties of the long- term leached Cast Stone monolith samples.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

On the Need for Comprehensive Validation of Deformable Image Registration, Investigated With a Novel 3-Dimensional Deformable Dosimeter

Purpose: To introduce and evaluate a novel deformable 3-dimensional (3D) dosimetry system (Presage-Def/Optical-CT) and its application toward investigating the accuracy of dose deformation in a commercial deformable image registration (DIR) package. Methods and Materials: Presage-Def is a new dosimetry material consisting of an elastic polyurethane matrix doped with radiochromic leuco dye. Radiologic and mechanical properties were characterized using standard techniques. Dose-tracking feasibility was evaluated by comparing dose distributions between dosimeters irradiated with and without 27% lateral compression. A checkerboard plan of 5-mm square fields enabled precise measurement of true deformation using 3D dosimetry. Predicted deformation was determined from a commercial DIR algorithm. Results: Presage-Def exhibited a linear dose response with sensitivity of 0.0032 ΔOD/(Gy∙cm). Mass density is 1.02 g/cm{sup 3}, and effective atomic number is within 1.5% of water over a broad (0.03-10 MeV) energy range, indicating good water-equivalence. Elastic characteristics were close to that of liver tissue, with Young's modulus of 13.5-887 kPa over a stress range of 0.233-303 kPa, and Poisson's ratio of 0.475 (SE, 0.036). The Presage-Def/Optical-CT system successfully imaged the nondeformed and deformed dose distributions, with isotropic resolution of 1 mm. Comparison with the predicted deformed 3D dose distribution identified inaccuracies in the commercial DIR algorithm. Although external contours were accurately deformed (submillimeter accuracy), volumetric dose deformation was poor. Checkerboard field positioning and dimension errors of up to 9 and 14 mm, respectively, were identified, and the 3D DIR-deformed dose γ passing rate was only γ{sub 3%/3} {sub mm} = 60.0%. Conclusions: The Presage-Def/Optical-CT system shows strong potential for comprehensive investigation of DIR algorithm accuracy. Substantial errors in a commercial DIR were found in the conditions evaluated. This work highlights the critical importance of careful validation of DIR algorithms before clinical implementation.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Novel method of room temperature ionic liquid assisted Fe{sub 3}O{sub 4} nanocubes and nanoflakes synthesis

Graphical abstract: - Highlights: • First time [Bmim][TfO] IL is used for the Fe{sub 3}O{sub 4} nanoparticle synthesis. • Novel method tunes Fe{sub 3}O{sub 4} nanocubes and nanoflakes forms influenced by the base and IL. • Fe{sub 3}O{sub 4} oxidized topotactically into γ-Fe{sub 2}O{sub 3} nanoparticles by annealing and base. • Uniform morphology with average size of 33 nm negligible superstructure are formed. • Ms values are characterized by thin layer of γ-Fe{sub 2}O{sub 3} on the nanoparticle surface. - Abstract: For the first time, the nanomagnetite superparamagnetic particles are successfully synthesized by precipitation method using 1-n-butyl-3-methylimidazolium trifluoromethane sulfonate [Bmim][TfO] ionic liquid medium/surfactant. The obtained Fe{sub 3}O{sub 4} particles are nanocubes and nanoflakes and this formation is influenced by the base concentration and anisotropic circumstances produced by the ionic liquid and their size varies from 20 nm to 150 × 300 nm (width × length). The synthesized magnetite nanoparticles are characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM) and Vibrating sample magnetometer (VSM) studies. The results show that the core of the Fe{sub 3}O{sub 4} nanoparticles is surrounded by a thin layer of γ-Fe{sub 2}O{sub 3} by topotactical partial oxidation, which is remarkably proceed with the subsequent calcination. The magnetite nanocubes have high saturation magnetization value and exhibit superparamagnetic hysteresis loop.

36 MATERIALS SCIENCE↗

Organic-Acid-Assisted Fabrication of Low-Cost Li-Rich Cathode Material (Li[Li1/6Fe1/6Ni1/6Mn1/2]O-2) for Lithium-Ion Battery

A novel Li-rich cathode Li[Li1/6Fe1/6Ni1/6Mn1/2]O-2 (0.4Li(2)MnO(3-)0.6LiFe(1/3)Ni(1/3)Mn(1/3)O(2)) was synthesized by a solgel method, which uses citric acid (SC), tartaric acid (ST), or adipic acid (SA) as a chelating agent. The structural, morphological, and electrochemical properties of the prepared samples were characterized by various methods. X-ray diffraction showed that single-phase materials are formed mainly with typical alpha-NaFeO2 layered structure (R3 m), and the SC sample has the lowest Li/Ni cation disorder. The morphological study indicated homogeneous primary particles in good distribution size (100 nm) with small aggregates. The Fe, Ni, and Mn valences were determined by X-ray absorption near-edge structure analysis. In coin cell tests, the initial reversible discharge capacity of an SA electrode was 289.7 mAh g(-1) at the 0.1C rate in the 1.54.8 V voltage range, while an SC electrode showed a better cycling stability with relatively high capacity retention. At the 2C rate, the SC electrode can deliver a discharge capacity of 150 mAh g(-1) after 50 cycles. Differential capacity vs voltage curves were employed to further investigate the electrochemical reactions and the structural change process during cycling. This low-cost, Fe-based compound prepared by the solgel method has the potential to be used as the high capacity cathode material for Liion batteries.

cathode↗

POWTEX visits POWGEN

The high-intensity time-of-flight (TOF) neutron diffractometer POWTEX for powder and texture analysis is currently being built prior to operation in the eastern guide hall of the research reactor FRM II at Garching close to Munich, Germany. Because of the world-wide 3 He crisis in 2009, the authors promptly initiated the development of 3 He-free detector alternatives that are tailor-made for the requirements of large-area diffractometers. Herein is reported the 2017 enterprise to operate one mounting unit of the final POWTEX detector on the neutron powder diffractometer POWGEN at the Spallation Neutron Source located at Oak Ridge National Laboratory, USA. As a result, presented here are the first angular- and wavelength-dependent data from the POWTEX detector, unfortunately damaged by a 50 g shock but still operating, as well as the efforts made both to characterize the transport damage and to successfully recalibrate the voxel positions in order to yield nonetheless reliable measurements. Also described is the current data reduction process using the PowderReduceP2D algorithm implemented in Mantid [Arnold et al. (2014). Nucl. Instrum. Methods Phys. Res. A , 764 , 156–166]. The final part of the data treatment chain, namely a novel multi-dimensional refinement using a modified version of the GSAS-II software suite [Toby & Von Dreele (2013). J. Appl. Cryst. 46 , 544–549], is compared with a standard data treatment of the same event data conventionally reduced as TOF diffraction patterns and refined with the unmodified version of GSAS-II . This involves both determining the instrumental resolution parameters using POWGEN's powdered diamond standard sample and the refinement of a friendly-user sample, BaZn(NCN) 2 . Although each structural parameter on its own looks similar upon comparing the conventional (1D) and multi-dimensional (2D) treatments, also in terms of precision, a closer view shows small but possibly significant differences. For example, the somewhat suspicious proximity of the a and b lattice parameters of BaZn(NCN) 2 crystallizing in Pbca as resulting from the 1D refinement (0.008 Å) is five times less pronounced in the 2D refinement (0.038 Å). Similar features are found when comparing bond lengths and bond angles, e.g. the two N—C—N units are less differently bent in the 1D results (173 and 175°) than in the 2D results (167 and 173°). The results are of importance not only for POWTEX but also for other neutron TOF diffractometers with large-area detectors, like POWGEN at the SNS or the future DREAM beamline at the European Spallation Source.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SU-E-I-64: X-Ray Coherent Scatter Mammography Simulation

Purpose: Conventional mammography has poor contrast between healthy and cancerous tissues due to the small difference in attenuation properties. Coherent scatter potentially provides more information because interference of coherently scattered radiation depends on the average intermolecular spacing, and can be used to characterize tissue types. However, typical coherent scatter analysis techniques are not compatible with rapid low dose screening modalities. Coherent scatter slot scan imaging is a novel imaging technique which provides new information with higher contrast. In this work a simulation was performed of coherent scatter slot scan imaging to assess its performance and provide system optimization. Methods: In coherent scatter imaging, the coherent scatter is exploited using a conventional slot scan mammography system with anti-scatter grids tilted at the characteristic angle of cancerous tissues. A Monte Carlo simulation was used to simulate the coherent scatter imaging. System optimization was performed across several parameters, including source voltage and filtration, tilt angle, source and grid distances, grid ratio, and shielding geometry. Results: The contrast was high and increased as the grid tilt angle was increased beyond the characteristic angle for the modeled carcinoma, and as the source voltage increased. Source filtration did not have a significant effect on contrast. Increasing grid ratio improved contrast at the expense of decreasing the signal to noise ratio (SNR). As the tumor size is decreased, additional shields to block the fat signal are necessary in order to detect the cancer signal. Conclusion: Coherent scatter analysis using a wide slot setup is promising as an enhancement for screening mammography. This work was supported by National Institutes of Health, # 7 R01EB009715.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Mechanical Properties of Gels; Stress from Confined Fluids

Abstract for Grant DE-FG02-97ER45642 Period: 1997-2002 Mechanical Properties of Gels 2002-2008 Stress from Confined Fluids Principal investigator: Prof. George W. Scherer Dept. Civil & Env. Eng./PRISM Eng. Quad. E-319 Princeton, NJ 08544 USA Recipient organization: Trustees of Princeton University 4 New South Princeton, NJ 08544 USA Abstract: The initial stage of this project, entitled Mechanical Properties of Gels, was dedicated to characterizing and explaining the properties of inorganic gels. Such materials, made by sol-gel processing, are of interest for fabrication of films, fibers, optical devices, advanced insulation and other uses. However, their poor mechanical properties are an impediment in some applications, so understanding the origin of these properties could lead to enhanced performance. Novel experimental methods were developed and applied to measure the stiffness and permeability of gels and aerogels. Numerical simulations were developed to reproduce the growth process of the gels, resulting in structures whose mechanical properties matched the measurements. The models showed that the gels are formed by the growth of relatively robust clusters of molecules that are joined by tenuous links whose compliance compromises the stiffness of the structure. Therefore, synthetic methods that enhance the links could significantly increase the rigidity of such gels. The next stage of the project focused on Stress from Confined Fluids. The first problem of interest was the enhanced thermal expansion coefficient of water that we measured in the nanometric pores of cement paste. This could have a deleterious effect on the resistance of concrete to rapid heating in fires, because the excessive thermal expansion of water in the pores of the concrete could lead to spalling and collapse. A series of experiments demonstrated that the expansion of water increases as the pore size decreases. To explain this behavior, we undertook a collaboration with Prof. Stephen Garofalini (Rutgers), who has developed the best simulations of water ever reported by use of molecular dynamics. Simulated heating of water in small pores provided quantitative agreement with experiments, and showed that the origin of the high expansion is the altered structure of water in the first two molecular layers adjacent to the pore wall. The final focus of the project was to understand the damage done by crystals growing in small pores. For example, the primary cause of damage to ancient monuments in the Mediterranean Basin is growth of salt crystals in the pores of the stone. Salt may enter stone as a result of capillary rise of groundwater, by leaching of mortar joints, deposition of marine spray, or reactions with atmospheric pollutants (such as oxides of nitrogen or sulfur). As the water evaporates, the salt solution becomes supersaturated and crystals precipitate. Stress results, because the salt usually repels the minerals in the pore walls. Our goal was to identify the factors contributing to the repulsion, so that we could develop a chemical treatment to reduce the repulsion and hence the stress. (We have recently demonstrated an effective treatment as part of a separately funded study.) In collaboration with Prof. Garofalini, molecular dynamics simulations have been done that correctly reproduce the structure of water around dissolved ions of sodium and chloride. We simulated the interaction between crystals of sodium chloride and quartz, and found that this particular system exhibits attractive forces, in agreement with experiment. The origin of the attraction is the orientation of dipolar water molecules near the surfaces of the crystals. Similar calculations now must be done in systems, such as potassium chloride and quartz, where the interaction is repulsive. This grant supported the education of two doctoral students, Hang-Shing Ma (Ph.D., 2002) and Melanie Webb (Ph.D. expected 2010), three post-doctoral researchers, Joachim Gross, Gudrun Reichenauer, and Shuangyan (Sonia) Xu, and five undergraduates (for senior theses or independent projects), Shawn Ryan, Mary Yang, Matthew Gill, Lindsay Karfeld, and Greg Simmons.

36 MATERIALS SCIENCE↗

Structural variation from heterometallic cluster-based 1D chain to heterometallic tetranuclear cluster: Syntheses, structures and magnetic properties

Using the solvothermal method, we present the comparative preparation of ([Co{sub 3}Na(dmaep){sub 3}(ehbd)(N{sub 3}){sub 3}]·DMF){sub n} (1) and [Co{sub 2}Na{sub 2}(hmbd){sub 4}(N{sub 3}){sub 2}(DMF){sub 2}] (2), where Hehbd is 3-ethoxy-2-hydroxy-benzaldehyde, Hhmbd is 3-methoxy-2-hydroxy-benzaldehyde, and Hdmaep is 2-dimethylaminomethyl-6-ethoxy-phenol, which was synthesized by an in-situ reaction. Complexes 1 and 2 were characterized by elemental analysis, IR spectroscopy, and X-ray single-crystal diffraction. Complex 1 is a novel heterometallic cluster-based 1-D chain and 2 is a heterometallic tetranuclear cluster. The (Co{sub 3}{sup II}Na) and (Co{sub 2}{sup II}Na{sub 2}) cores display dominant ferromagnetic interaction from the nature of the binding modes through μ{sub 1,1,1}-N{sub 3}{sup –} (end-on, EO). - Graphical abstract: Two novel cobalt complexes have been prepared. Compound 1 consists of tetranuclear (Co{sub 3}{sup II}Na) units, which further formed a 1-D chain. Compound 2 is heterometallic tetranuclear cluster. Two complexes display dominant ferromagnetic interaction. - Highlights: • Two new heterometallic complexes have been synthesized by solvothermal method. • The stereospecific blockade of the ligands in the synthesis system seems to be the most important synthetic parameter. • The magnetism studies show that 1 and 2 exhibit ferromagnetic interactions. • Complex 1 shows slowing down of magnetization and not blocking of magnetization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sonochemical and hydrothermal synthesis of PbTe nanostructures with the aid of a novel capping agent

Graphical abstract: - Highlights: • PbTe nanostructures were prepared with the aid of Schiff-base compound. • Sonochemical and hydrothermal methods were employed to fabricate PbTe nanostrucrues. • The effect of preparation parameters on the morphology of PbTe was investigated. - Abstract: In this work, a new Schiff-base compound derived from 1,8-diamino-3,6-dioxaoctane and 2-hydroxy-1-naphthaldehyde marked as (2-HyNa)-(DaDo) was synthesized, characterized, and then used as capping agent for the preparation of PbTe nanostructures. To fabricate PbTe nanostructures, two different synthesis methods; hydrothermal and sonochemical routes, were applied. To further investigate, the effect of preparation parameters like reaction time and temperature in hydrothermal synthesis and sonication time in the presence of ultrasound irradiation on the morphology and purity of the final products was tested. The products were analyzed with the aid of SEM, TEM, XRD, FT-IR, and EDS. Based on the obtained results, it was found that pure cubic phased PbTe nanostructures have been obtained by hydrothermal and sonochemical approaches. Besides, SEM images showed that cubic-like and rod-like PbTe nanostructures have been formed by hydrothermal and sonochemical methods, respectively. Sonochemical synthesis of PbTe nanostructures was favorable, because the synthesis time of sonochemical method was shorter than that of hydrothermal method.

36 MATERIALS SCIENCE↗

Polymers in Lithium‐Ion and Lithium Metal Batteries

Abstract Lithium‐ion batteries play a significant role in modern electronics and electric vehicles. However, current Li‐ion battery chemistries are unable to satisfy the increasingly heightened expectations regarding energy demand and reliability. To boost the overall energy density while ensuring the safety of Li batteries, researchers have focused on alternative battery materials, such as silicon, sulfur, and Li metal. These represent promising avenues, although numerous obstacles (e.g., Si cracking, polysulfide shuttling, Li dendrites, etc.) must be tackled before batteries based on these materials can enter mass production and penetrate the mainstream market. Polymers are a class of materials that are widely used in current battery systems; however, many novel polymer chemistries may offer better performance and reliability than the current ones, and even overcome the issues of the above‐mentioned new battery materials. In this review, selected polymeric materials for solving these issues are categorized into four parts: polymer electrolytes, polymer artificial solid‐electrolyte interphases, binders, and separators. Both the current progress and the characterization methods are included. Potential future directions of energy materials research are pointed out as well.

Li, Junheng↗

High Removal Capacity of Arsenic from Drinking Water Using Modified Magnetic Polyurethane Foam Nanocomposites

In this study, a novel polyurethane foam (PU) nanocomposite adsorbent based on silane-modified magnetic iron-oxide nanoparticles (Fe{sub 3}O{sub 4}@APTES) is synthesized via a low cost and simple in situ polymerization method for the removal of arsenic ions from aqueous solutions. The chemical structure and surface morphology of the prepared nanoparticles and adsorbent were characterized using Fourier transform infrared spectroscopy, attenuated total reflection, scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. Inductively coupled plasma mass spectrometry was used to measure the arsenic concentration of the treated solutions. Sorption isotherms models were applied to determine the adsorption mechanism and modeling parameters. The removal capacity of the modified PU foam was at its highest during a contact time of four hours which resulted in a removal capacity of 95%. Kinetic studies were conducted to determine the adsorption capacity and the uptake rate of arsenic. A Pseudo-order model was found to be the best fit model for adsorption. The prepared adsorbent can be separated from the solution by using an external magnet field.

36 MATERIALS SCIENCE↗