Search NASA⌕ Search

SEARCH · Search NASA

Results for “Numerical performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

An Experimental and Numerical Study of Icing Effects on the Performance and Controllability of a Twin Engine Aircraft

In September 1997 the National Transportation Safety Board (NTSB) requested assistance from the NASA Lewis Research Center (LeRC) Icing Branch in the investigation of an aircraft accident that was suspected of being caused by ice contamination. In response to the request NASA agreed to perform an experimental and computational study. The main activities that NASA performed were LERC Icing Research Tunnel (IRT) testing to define ice shapes and 2-D Navier-Stokes analysis to determine the performance degradation that those ice shapes would have caused. An IRT test was conducted in January 1998. Most conditions for the test were based upon raw and derived data from the Flight Data Recorder (FDR) recovered from the accident and upon the current understanding of the Meteorological conditions near the accident. Using a two-dimensional Navier-Stokes code, the flow field and resultant lift and drag were calculated for the wing section with various ice shapes accreted in the IRT test. Before the final calculations could be performed extensive examinations of geometry smoothing and turbulence were conducted. The most significant finding of this effort is that several of the five-minute ice accretions generated in the IRT were found by the Navier-Stokes analysis to produce severe lift and drag degradation. The information generated by this study suggests a possible scenario for the kind of control upset recorded in the accident. Secondary findings were that the ice shapes accreted in the IRT were mostly limited to the protected pneumatic boot region of the wing and that during testing, activation of the pneumatic boots cleared most of the ice.

Reehorst, A.↗
NASA NTRS2003

The Formation of Asteroid Satellites in Catastrophic Impacts: Results from Numerical Simulations

We have performed new simulations of the formation of asteroid satellites by collisions, using a combination of hydrodynamical and gravitational dynamical codes. This initial work shows that both small satellites and ejected, co-orbiting pairs are produced most favorably by moderate-energy collisions at more direct, rather than oblique, impact angles. Simulations so far seem to be able to produce systems qualitatively similar to known binaries. Asteroid satellites provide vital clues that can help us understand the physics of hypervelocity impacts, the dominant geologic process affecting large main belt asteroids. Moreover, models of satellite formation may provide constraints on the internal structures of asteroids beyond those possible from observations of satellite orbital properties alone. It is probable that most observed main-belt asteroid satellites are by-products of cratering and/or catastrophic disruption events. Several possible formation mechanisms related to collisions have been identified: (i) mutual capture following catastrophic disruption, (ii) rotational fission due to glancing impact and spin-up, and (iii) re-accretion in orbit of ejecta from large, non-catastrophic impacts. Here we present results from a systematic investigation directed toward mapping out the parameter space of the first and third of these three collisional mechanisms.

Durda, D. D.↗
DOE OSTI2020

The cosmological analysis of the SDSS/BOSS data from the Effective Field Theory of Large-Scale Structure

The Effective Field Theory of Large-Scale Structure is a formalism that allows us to predict the clustering of Cosmological Large-Scale Structure in the mildly non-linear regime in an accurate and reliable way. In this paper, after validating our technique against several sets of numerical simulations, we perform the analysis for the cosmological parameters of the DR12 BOSS data. We assume Λ CDM, a fixed value of the baryon/dark-matter ratio, Ω b /Ω c , and of the tilt of the primordial power spectrum, n s , and no significant input from numerical simulations. By using the one-loop power spectrum multipoles, we measure the primordial amplitude of the power spectrum, A s , the abundance of matter, Ω m , and the Hubble parameter, H 0 , {to about 13% , 3.2% and 3.2% respectively, obtaining ln (10 10 A s )=2.72± 0.13 , 0Ω m =0.309± 0.01 , H 0 =68.5± 2.2 km/(s Mpc) at 68% confidence level. If we then add a CMB prior on the sound horizon, the error bar on H 0 is reduced to 1.6% .} These results are a substantial qualitative and quantitative improvement with respect to former analyses, and suggest that the EFTofLSS is a powerful instrument to extract cosmological information from Large-Scale Structure.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1985

A mixed pseudospectral/finite difference method for a thermally driven fluid in a nonuniform gravitational field

A numerical study of the steady, axisymmetric flow in a heated, rotating spherical shell is conducted to model the Atmospheric General Circulation Experiment (AGCE) proposed to run aboard a later Shuttle mission. The AGCE will consist of concentric rotating spheres confining a dielectric fluid. By imposing a dielectric field across the fluid a radial body force will be created. The numerical solution technique is based on the incompressible Navier-Stokes equations. In the method a pseudospectral technique is used in the latitudinal direction, and a second-order accurate finite difference scheme discretizes time and radial derivatives. This paper discusses the development and performance of this numerical scheme for the AGCE which has been modeled in the past only by pure FD formulations. In addition, previous models have not investigated the effect of using a dielectric force to simulate terrestrial gravity. The effect of this dielectric force on the flow field is investigated as well as a parameter study of varying rotation rates and boundary temperatures. Among the effects noted are the production of larger velocities and enhanced reversals of radial temperature gradients for a body force generated by the electric field.

Macaraeg, M. G.↗
NASA NTRS1995

Wave journal bearing with compressible lubricant--Part 1: The wave bearing concept and a comparison to the plain circular bearing

To improve hydrodynamic journal bearing steady-state and dynamic performance, a new bearing concept, the wave journal bearing, was developed at the author's lab. This concept features a waved inner bearing diameter. Compared to other alternative bearing geometries used to improve bearing performance such as spiral or herring-bone grooves, steps, etc., the wave bearing's design is relatively simple and allows the shaft to rotate in either direction. A three-wave bearing operating with a compressible lubricant, i.e., gas is analyzed using a numerical code. Its performance is compared to a plain (truly) circular bearing over a broad range of bearing working parameters, e.g., bearing numbers from 0.01 to 100.

Dimofte, Florin↗
NASA NTRS1992

Computation of three-dimensional effects on two dimensional wings

A 2-D numerical investigation was performed to determine the effect of a Gurney flap on a NACA 4412 airfoil. A Gurney flap is a flat plate on the order of 1 to 3 percent of the airfoil chord length, oriented perpendicular to the airfoil chord line and located at the trailing edge of the airfoil. An incompressible Navier Stokes code, INS2D, was used to calculate the flow field about the airfoil. The fully turbulent results were obtained using the Baldwin-Barth one-equation turbulence model. Gurney flap sizes of 0.5, 1, 1.25, 1.5, 2, and 3 percent of the airfoil chord were studied. Computational results were compared with experimental results where possible. The numerical solutions show that the Gurney flap increases airfoil lift coefficient with only a slight increase in drag coefficient. Use of a 1.5 percent chord Gurney flap increases the maximum lift coefficient by approximately 0.3 and decreases the angle of attack for a given lift coefficient by more than 3 degrees. The numerical solutions exhibit detailed flow structures at the trailing edge and provide a possible explanation for the increased aerodynamic performance.

Cummings, Russell M.↗
NASA NTRS1992

Computational evaluation of an airfoil with a Gurney flap

A 2D numerical investigation was performed to determine the effect of a Gurney flap on a NACA 4412 airfoil. A Gurney flap is a flat plate on the order of 1 to 3 percent of the airfoil chord length, oriented perpendicular to the airfoil chord line and located at the trailing edge of the airfoil. An incompressible Navier Stokes code, INS2D, was used to calculate the flow field about the airfoil. The fully turbulent results were obtained using the Baldwin-Barth one-equation turbulence model. Gurney flap sizes of 0.5 , 1, 1.25, 1.5, 2, and 3 percent of the airfoil chord were studied. Computational results were compared with experimental results where possible. The numerical solutions show that the Gurney flap increases airfoil lift coefficient with only a slight increase in drag coefficient. Use of a 1.5 percent chord Gurney flap increases the maximum lift coefficient by approximately 0.3 and decreases the angle of attack for a given lift coefficient by more than 3 deg. The numerical solutions exhibit detailed flow structures at the trialing edge and provide a possible explanation for the increased aerodynamic performance.

Jang, Cory S.↗
NASA NTRS1977

Application of LANDSAT data to wetland study and land use classification in west Tennessee

The Obion-Forked Deer River Basin in northwest Tennessee is confronted with several acute land use problems which result in excessive erosion, sedimentation, pollution, and hydrologic runoff. LANDSAT data was applied to determine land use of selected watershed areas within the basin, with special emphasis on determining wetland boundaries. Densitometric analysis was performed to allow numerical classification of objects observed in the imagery on the basis of measurements of optical densities. Multispectral analysis of the LANDSAT imagery provided the capability of altering the color of the image presentation in order to enhance desired relationships. Manual mapping and classification techniques were performed in order to indicate a level of accuracy of the LANDSAT data as compared with high and low altitude photography for land use classification.

Jones, N. L.↗
NASA NTRS1982

Stability of boundary layers with porous suction strips: Experiment and theory

Low turbulence tunnel experiments on the stability and transition of 2 D boundary layers on flat plates with and without suction are described. A number of general suction cases are discussed. Test results showed that the maximum stabilization occurred when the suction was moved toward the Branch I neutral point. An analytical study of the stability of two dimensional, incompressible boundary layer flows over plates with suction through porous strips was performed. The mean flow was calculated using linearized triple deck, closed form solutions. The stability results of the triple deck theory are shown to be in good agreement with those of the interacting boundary layers. An analytical optimization scheme for the suction configuration was developd. Numerical calculations were performed corresponding to the experimental configurations. In each case, the theory correctly predicts the experimental results.

Reynolds, G. A.↗
NASA NTRS1999

A Robust Locally Preconditioned Semi-Coarsening Multigrid Algorithm for the 2-D Navier-Stokes Equations

The goal of this thesis is to develop an efficient and robust locally preconditioned semi-coarsening multigrid algorithm for the two-dimensional Navier-Stokes equations. This thesis examines the performance of the multigrid algorithm with local preconditioning for an upwind-discretization of the Navier-Stokes equations. A block Jacobi iterative scheme is used because of its high frequency error mode damping ability. At low Mach numbers, the performance of a flux preconditioner is investigated. The flux preconditioner utilizes a new limiting technique based on local information that was developed by Siu. Full-coarsening and-semi-coarsening are examined as well as the multigrid V-cycle and full multigrid. The numerical tests were performed on a NACA 0012 airfoil at a range of Mach numbers. The tests show that semi-coarsening with flux preconditioning is the most efficient and robust combination of coarsening strategy, and iterative scheme - especially at low Mach numbers.

Cain, Michael D.↗
NASA NTRS2003

Simulations of 6-DOF Motion with a Cartesian Method

Coupled 6-DOF/CFD trajectory predictions using an automated Cartesian method are demonstrated by simulating a GBU-32/JDAM store separating from an F-18C aircraft. Numerical simulations are performed at two Mach numbers near the sonic speed, and compared with flight-test telemetry and photographic-derived data. Simulation results obtained with a sequential-static series of flow solutions are contrasted with results using a time-dependent flow solver. Both numerical methods show good agreement with the flight-test data through the first half of the simulations. The sequential-static and time-dependent methods diverge over the last half of the trajectory prediction. after the store produces peak angular rates. A cost comparison for the Cartesian method is included, in terms of absolute cost and relative to computing uncoupled 6-DOF trajectories. A detailed description of the 6-DOF method, as well as a verification of its accuracy, is provided in an appendix.

Murman, Scott M.↗
NASA NTRS2012

Shock Generation and Control Using DBD Plasma Actuators

This report is the final report of a NASA Phase I SBIR contract, with some revisions to remove company proprietary data. The Shock Boundary Layer Interaction (SBLI) phenomena in a supersonic inlet involve mutual interaction of oblique shocks with boundary layers, forcing the boundary layer to separate from the inlet wall. To improve the inlet efficiency, it is desired to prevent or delay shock-induced boundary layer separation. In this effort, Innovative Technology Applications Company (ITAC), LLC and the University of Notre Dame (UND) jointly investigated the use of dielectric-barrier-discharge (DBD) plasma actuators for control of SBLI in a supersonic inlet. The research investigated the potential for DBD plasma actuators to suppress flow separation caused by a shock in a turbulent boundary layer. The research involved both numerical and experimental investigations of plasma flow control for a few different SBLI configurations: (a) a 12 wedge flow test case at Mach 1.5 (numerical and experimental), (b) an impinging shock test case at Mach 1.5 using an airfoil as a shock generator (numerical and experimental), and (c) a Mach 2.0 nozzle flow case in a simulated 15 X 15 cm wind tunnel with a shock generator (numerical). Numerical studies were performed for all three test cases to examine the feasibility of plasma flow control concepts. These results were used to guide the wind tunnel experiments conducted on the Mach 1.5 12 degree wedge flow (case a) and the Mach 1.5 impinging shock test case (case b) which were at similar flow conditions as the corresponding numerical studies to obtain experimental evidence of plasma control effects for SBLI control. The experiments also generated data that were used in validating the numerical studies for the baseline cases (without plasma actuators). The experiments were conducted in a Mach 1.5 test section in the University of Notre Dame Hessert Laboratory. The simulation results from cases a and b indicated that multiple spanwise actuators in series and at a voltage of 75 kVp-p could fully suppress the flow separation downstream of the shock. The simulation results from case c showed that the streamwise plasma actuators are highly effective in creating pairs of counter-rotating vortices, much like the mechanical vortex generators, and could also potentially have beneficial effects for SBLI control. However, to achieve these effects, the positioning and the quantity of the DBD actuators used must be optimized. The wind tunnel experiments mapped the baseline flow with good agreement to the numerical simulations. The experimental results were conducted with spanwise actuators for cases a and b, but were limited by the inability to generate a sufficiently high voltage due to arcing in the wind-tunnel test-section. The static pressure in the tunnel was lower than the static pressure in an inlet at flight conditions, promoting arching and degrading the actuator performance.

Patel, Mehul P.↗
DOE OSTI2025

From Machine Learning to Machine Reasoning: A Model-based Approach to Analyze Equipment Reliability Data

In current nuclear power plants (NPPs) a large amount of condition-based data which can be used to assess and monitor component health and performance. Assessing component health from such data can be performed with a large variety of methods. While the analysis of numeric data can be performed with several methods, the extraction of information from textual data remains a challenge. Currently employed natural language processing (NLP) methods do not really provide quantitative information that might be contained in IRs. In addition, the integration of numeric and textual data to identify possible causal relationships between data elements is still an unresolved challenge. This paper presents an approach to extract information from textual (e.g., incident or maintenance reports) and numeric data that relies on model based system engineer (MBSE) models. MBSE are diagrams designed to represent system and component dependencies (from both a form and functional point of view). In our approach, MBSE models emulate system engineer knowledge about component/system architecture. NLP methods are employed to perform syntactic and semantic analyses. Syntactic analysis analyzes the grammatical structure of a sentence while semantic analysis is designed to analyze the logic structure of a sentence. An innovative element of our approach is that semantic analysis uses MBSE models to identify links between textual elements. Similarly, numeric data is directly linked to elements of the MBSE models in order to map which functions are being monitored.

97 - MATHEMATICS AND COMPUTING↗
NASA NTRS1988

3-D plume flow computations with an upwind solver

In the present study multi-nozzle plume flows are computed with a three-dimensional, Navier-Stokes solver. Numerical simulations are performed with the flux-split, two-factor, time symptotic, viscous flow solver. The two factor splitting provides a stable three-dimensional solution procedure under ideal-gas assumptions. Viscous, ideal-gas solutions for a thin lip symmetrical nozzle are compared with experimental and numerical solutions. Computed solutions to axisymmetric and three-dimensional, multi-nozzle problems at various altitudes and flight conditions demonstrate flow field complexity and three-dimensional effects.

Venkatapathy, Ethiraj↗
DOE OSTI2021

An adaptive Hessian approximated stochastic gradient MCMC method

Bayesian approaches have been successfully integrated into training deep neural networks. One popular family is stochastic gradient Markov chain Monte Carlo methods (SG-MCMC), which have gained increasing interest due to their ability to handle large datasets and the potential to avoid overfitting. Although standard SG-MCMC methods have shown great performance in a variety of problems, they may be inefficient when the random variables in the target posterior densities have scale differences or are highly correlated. Here, we present an adaptive Hessian approximated stochastic gradient MCMC method to incorporate local geometric information while sampling from the posterior. The idea is to apply stochastic approximation (SA) to sequentially update a preconditioning matrix at each iteration. The preconditioner possesses second-order information and can guide the random walk of a sampler efficiently. Instead of computing and saving the full Hessian of the log posterior, we use limited memory of the samples and their stochastic gradients to approximate the inverse Hessian-vector multiplication in the updating formula. Moreover, by smoothly optimizing the preconditioning matrix via SA, our proposed algorithm can asymptotically converge to the target distribution with a controllable bias under mild conditions. To reduce the training and testing computational burden, we adopt a magnitude-based weight pruning method to enforce the sparsity of the network. Our method is user-friendly and demonstrates better learning results compared to standard SG-MCMC updating rules. The approximation of inverse Hessian alleviates storage and computational complexities for large dimensional models. Numerical experiments are performed on several problems, including sampling from 2D correlated distribution, synthetic regression problems, and learning the numerical solutions of heterogeneous elliptic PDE. The numerical results demonstrate great improvement in both the convergence rate and accuracy.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

A Lamination Model for Pressure-Assisted Sintering of Multilayered Porous Structures

This work describes a lamination model for pressure-assisted sintering of thin, multilayered, and porous structures based on the linear viscous constitutive theory of sintering and the classical laminated plate theory of continuum mechanics. A constant out-of-plane normal stress is assumed in the constitutive relation. The lamination relations between the force/moment resultants and the strain/curvature rates are presented. Numerical simulations were performed for a symmetric tri-layer laminate consisting of a 10% gadolinia doped ceria (Ce 0.9 Gd 0.1 O 1.95-δ ) composite structure, where porous layers were adhered to the top and bottom of a denser layer under uniaxially-applied pressures and the sinter forging conditions. The numerical results show that, compared with free sintering, the applied pressure can significantly reduce the sintering time required to achieve given layer thicknesses and porosities. Unlike free sintering, which results in a monotonic decrease of the laminate in-plane dimension, pressure-assisted sintering may produce an in-plane dimension increase or decrease, depending on the applied pressure and sintering time. Finally, the individual layers in the laminate exhibit different stress characteristics under pressure-assisted sintering.

42 ENGINEERING↗
NASA NTRS1984

Numerical experiments on galaxy clustering in open universes

Numerical studies were performed on the dynamical effects on the evolution of clumps, filaments, voids, and galaxy clusters by various final Omega values. The final Omega values examined ranged from 0.03-1, and attention was given to defining observations of superclusters which would aid in determining an actual value for Omega. The numerical trials consisted of n-body integration programs governed by the total expansion and final Omega value and included comparisons between results for open and closed universes. All runs started from the same initial conditions. The dispersion trajectories of particles and the final galactic cluster forms were found to be equivalent, regardless of the final Omega value. The possibility of deriving a value for Omega from velocity data on galaxies which have not yet joined clusters is discussed.

Miller, R. H.↗
NASA NTRS1973

The influence of laser ranging on selenodetic control.

A mathematical model for performing an adjustment, using laser distances to improve coordinates of points on the earth and on the moon, as well as the orientation of these two bodies in space, is presented. The observation equations are given, and the orientation of the earth and the moon are defined in terms of three Eulerian angles. Numerical experiments were performed to investigate the expected accuracies of parameters in the adjustment model under differing conditions. The results indicate that the statistics both for the coordinates of points on earth and on the moon, and for the orientation parameters of the two bodies are favorable. However, very high correlations exist between some of the parameters; therefore, the recovery of these parameters from a simultaneous adjustment is questionable.

Mueller, I. I.↗