Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE DISTRIBUTION - AIRFOILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A computational study of heat transfer for laminar hypervelocity flows

Computational Fluid Dynamics (CFD) codes are routinely used to predict the flowfield and the heating environment around complex reentry configurations. At hypervelocities, where the velocity is greater than 3 km/sec, the AFWAL version of the blunt body code predicts the correct surface pressure distributions but underpredicts laminar wall heat fluxes. This study was performed to determine the reasons for the underprediction. The computer code chosen solves thin-layer Navier-Stokes equations in a time-asymptotic manner and assumes a constant isentropic exponent. Flowfields around a spherical configuration at various entry velocities are computed. The computed pressure distributions agree well with the tabulated, inviscid results of Lyubimov and Rusanov for entry velocities ranging from 0.6 to 5.92 km/sec. At hypervelocities, the calculated stagnation point heat transfer rates were lower by roughly fifty percent when compared to engineering correlations available in the literature. Good comparisons between heat transfer rates are obtained at hypervelocity entry conditions provided the CFD code is modified to include equilibrium air properties.

Balakrishnan, A.↗
NASA NTRS1999

Coupling of Low Speed Fan Stator Vane Unsteady Pressures to Duct Modes: Measured versus Predicted

Uniform-flow annular-duct Green's functions are the essential elements of the classical acoustic analogy approach to the problem of computing the noise generated by rotor-stator interaction inside the fan duct. This paper investigates the accuracy of this class of Green's functions for predicting the duct noise levels when measured stator vane unsteady surface pressures are used as input to the theoretical formulation. The accuracy of the method is evaluated by comparing the predicted and measured acoustic power levels for the NASA 48 inch low speed Active Noise Control Fan. The unsteady surface pressures are measured,by an array of microphones imbedded in the suction and pressure sides of a single vane, while the duct mode levels are measured using a rotating rake system installed in the inlet and exhaust sections of the fan duct. The predicted levels are computed using properly weighted integrals of measured surface pressure distribution. The data-theory comparisons are generally quite good particularly when the mode cut-off criterion is carefully interpreted. This suggests that, at least for low speed fans, the uniform-flow annular-duct Green's function theory can be reliably used for prediction of duct mode levels if the cascade surface pressure distribution is accurately known.

Sutliff, Daniel L.↗
NASA NTRS1951

Flow Separation Ahead of a Blunt Axially Symmetric Body at Mach Numbers 1.76 to 2.10

The pressure distribution and drag were determined for a spherical-nosed axially symmetric body with thin projecting rods at Mach numbers of 1.76, 1.93, and 2.10. The upstream projection distance of the rods was varied over a wide range to study changes in the character of the flow separation and to determine the variation of drag and pressure distribution with tip projection. Drag coefficients between 0.18 and 0.30 were obtained for most tip projections at each Mach number.

WIND TUNNEL TESTS - LFPL - SUPERSONIC (18"x18")↗
NASA NTRS2005

Active control of Boundary Layer Separation & Flow Distortion in Adverse Pressure Gradient Flows via Supersonic Microjets

Inlets to aircraft propulsion systems must supply flow to the compressor with minimal pressure loss, flow distortion or unsteadiness. Flow separation in internal flows such as inlets and ducts in aircraft propulsion systems and external flows such as over aircraft wings, is undesirable as it reduces the overall system performance. The aim of this research has been to understand the nature of separation and more importantly, to explore techniques to actively control this flow separation. In particular, the use of supersonic microjets as a means of controlling boundary layer separation was explored. The geometry used for the early part of this study was a simple diverging Stratford ramp, equipped with arrays of supersonic microjets. Initial results, based on the mean surface pressure distribution, surface flow visualization and Planar Laser Scattering (PLS) indicated a reverse flow region. We implemented supersonic microjets to control this separation and flow visualization results appeared to suggest that microjets have a favorable effect, at least to a certain extent. However, the details of the separated flow field were difficult to determine based on surface pressure distribution, surface flow patterns and PLS alone. It was also difficult to clearly determine the exact influence of the supersonic microjets on this flow. In the latter part of this study, the properties of this flow-field and the effect of supersonic microjets on its behavior were investigated in further detail using 2-component (planar) Particle Image Velocimetry (PIV). The results clearly show that the activation of microjets eliminated flow separation and resulted in a significant increase in the momentum of the fluid near the ramp surface. Also notable is the fact that the gain in momentum due to the elimination of flow separation is at least an order of magnitude larger (two orders of magnitude larger in most cases) than the momentum injected by the microjets and is accomplished with very little mass flow through the microjets.

Alvi, Farrukh S.↗
NASA NTRS1980

Unified aerodynamic-acoustic theory for a thin rectangular wing encountering a gust

A linear aerodynamic-acoustic theory is developed for the prediction of the surface pressure distribution and three-dimensional acoustic far-field for a flat plate rectangular wing encountering a stationary short-wavelength oblique gust. It is suggested that for an infinite-span wing, leading- and trailing-edge responses to a short-wavelength gust are essentially independent. This idea is used to solve for the two-dimensional pressure field due to the passage of an infinite-span wing through an oblique gust. By allowing the field point to come down to the wing's surface, one finds an expression for the surface pressure distribution which agrees with that given in the two-dimensional aerodynamic theories of Amiet and Adamczyk. Spanwise Fourier superposition of two-dimensional solutions to the infinite-span wing problem is used to approximate the three-dimensional acoustic field due to the interaction of a stationary oblique gust with a flat-plate rectangular wing traveling at a subsonic speed.

Martinez, R.↗
NASA NTRS1975

Application of local linearization and the transonic equivalence rule to the flow about slender analytic bodies at Mach numbers near 1.0

The local linearization method for axisymmetric flow is combined with the transonic equivalence rule to calculate pressure distribution on slender bodies at free-stream Mach numbers from .8 to 1.2. This is an approximate solution to the transonic flow problem which yields results applicable during the preliminary design stages of a configuration development. The method can be used to determine the aerodynamic loads on parabolic arc bodies having either circular or elliptical cross sections. It is particularly useful in predicting pressure distributions and normal force distributions along the body at small angles of attack. The equations discussed may be extended to include wing-body combinations.

Tyson, R. W.↗
NASA NTRS2003

Exploratory Calibration of Adjustable-Protrusion Surface-Obstacle (APSO) Skin Friction Vector Gage

The design of an adjustable-protrusion surface-obstacle (APSO) skin friction vector gage is presented. Results from exploratory calibrations conducted in laminar and turbulent boundary layers at the Washington University Low-Speed Wind Tunnel and for turbulent boundary layers at speeds up to Mach 2 on the ceiling of the NASA Glenn Research Center 8- X 6-ft Supersonic Wind Tunnel are also discussed. The adjustable-height gage was designed to yield both the magnitude and direction of the surface shear stress vector and to measure the local static pressure distribution. Results from the NASA test show good correlation for subsonic and low supersonic conditions covering several orders of magnitude in terms of the adopted similarity variables. Recommendations for future work in this area consist of identifying the physical parameters responsible for the disagreement between the university and NASA data sets, developing a compressibility correction specific to the APSO geometry, and examining the effect that static pressure distribution and skewed boundary layers have on the results from the APSO.

Hakkinen, Raimo J.↗
NASA NTRS2018

Wall-Resolved Large Eddy Simulations of Transonic Shock-Induced Flow Separation

This paper reports the wall-resolved large eddy simulations of shock-induced boundary layer separation over an axisymmetric bump for a flow Mach number of 0.875 and a chord-based Reynolds number of 2.763 million. The incoming boundary layer has a momentum-thickness Reynolds number of 6600 at one and a half chord lengths upstream of the leading edge. The calculations simulate the experiment by Bachalo and Johnson (AIAA Journal, Vol. 24, No. 3, 1986), except that the tunnel walls are ignored and the simulations are performed assuming free air with as many as 24 billion grid points. The effects of domain span, grid resolution and time step on the predictions are examined. The results are found to show some sensitivity to the studied parameters. Owing to the outer boundary conditions, the predicted surface pressure distribution as well as the flow separation and reattachment locations tend to agree better with the experimental results from the larger (6 × 6 ft) tunnel than those from the smaller (2 × 2 ft) tunnel. The predicted Reynolds shear stress profiles in the separated region differ by as much as 31%from the experimental results that were only obtained in the smaller tunnel. The most accurate surface pressure distribution obtained in this study lies within the scatter of the measurements taken in the two facilities.

Uzun, Ali↗
NASA NTRS1983

Thermal elastohydrodynamic lubrication of line contacts

A numerical solution to the problem of thermal elastohydrodynamic lubrication of line contacts was obtained by using a finite difference formulation. The solution procedure consists of simultaneous solution of the thermal Reynolds equation, the elasticity equation, and the energy equation subject to appropriate boundary conditions. Pressure distribution, film shape, and temperature distribution were obtained for fully flooded conjunctions, a paraffinic lubricant, and various dimensionless speed parameters while the dimensionless load and materials parameters were held constant. Reduction in the minimum film thickness due to thermal effects (as a ratio of thermal to isothermal minimum film thickness) is given by a simple formula as a function of the thermal loading parameter Q: H(min)/H(min,I) = 10/10+ Q(0.4). Plots of pressure distribution, film shape, temperature distribution, and flow are shown for some representative cases.

Ghosh, M. K.↗
NASA NTRS1985

Thermal elastohydrodynamic lubrication of line contacts

A numerical solution to the problem of thermal elastohydrodynamic lubrication of line contacts was obtained by using a finite difference formulation. The solution procedure consists of simultaneous solution of the thermal Reynolds equation, the elasticity equation, and the energy equation subject to appropriate boundary conditions. Pressure distribution, film shape, and temperature distribution were obtained for fully flooded conjunctions, a paraffinic lubricant, and various dimensionless speed parameters while the dimensionless load and materials parameters were held constant. Reduction in the minimum film thickness due to thermal effects (as a ratio of thermal to isothermal minimum film thickness) is given by a simple formula as a function of the thermal loading parameter Q: H(min)/H(min, I) = 10/10 + Q(0.4). Plots of pressure distribution, film shape, temperature distribution, and flow are shown for some representative cases.

Ghosh, M. K.↗
NASA NTRS1977

A three-dimensional viscous/potential flow interaction analysis method for multi-element wings

An analysis method and computer program were developed for the calculation of the viscosity dependent aerodynamic characteristics of multi-element, finite wings in incompressible flow. A fully-three dimensional potential flow program is used to determine the inviscid pressure distribution about the configuration. The potential flow program uses surface source and vortex singularities to represent the inviscid flow. The method is capable of analysing configurations having at most one slat, a main element, and two slotted flaps. Configurations are limited to full span slats or flaps. The configuration wake is allowed to relax as a force free wake, although roll up is not allowed at this time. Once the inviscid pressure distribution is calculated, a series of boundary layer computations are made along streamwise strips.

Dvorak, F. A.↗
NASA NTRS1971

On the transonic aerodynamics of a compressor blade row

Linearized analyses have been carried out for the induced velocity and pressure fields within a compressor blade row operating in an infinite annulus at transonic Mach numbers of the flow relative to the blades. In addition, the relationship between the induced velocity and the shape of the mean blade surface has been determined. A computational scheme has been developed for evaluating the blade mean surface ordinates and surface pressure distributions. The separation of the effects of a specified blade thickness distribution from the effects of a specified distribution of the blade lift has been established. In this way, blade mean surface shapes that are necessary for the blades to be locally nonlifting have been computed and are presented for two examples of blades with biconvex parabolic arc sections of radially tapering thickness. Blade shapes that are required to achieve a zero thickness, uniform chordwise loading, constant work spanwise loading are also presented for two examples. In addition, corresponding surface pressure distributions are given. The flow relative to the blade tips has a high subsonic Mach number in the examples that have been computed. The results suggest that at near-sonic relative tip speeds the effective blade shape is dominated by the thickness distribution, with the lift distribution playing only a minor role.

Erickson, J. C., Jr.↗
NASA NTRS1962

On the Dynamic Characteristics of Free-Liquid Jets and a Partial Correlation with Orifice Geometry

A technique for evaluating the dynamic characteristics of free-liquid jets on a comparative basis is presented. This method consists of determining the pressure distribution produced by the perpendicular impingement of a jet upon a flat plate and using these data for comparing and categorizing jets with unknown properties in terms of similar data produced by jets having known characteristics-i.e., with jets produced by fully developed turbulent flow, fully developed laminar flow, and a jet having a near-uniform velocity profile. The visual characteristics, as well as both the mean and the fluctuating pressure distributions, are presented for these three reference configurations and for a number of jets produced by orifices having varying length-diameter ratios, combined with varying degrees of surface roughness in the initial five diameters of straight bore.

Rupe, Jack H.↗
NASA NTRS1993

Characterization of cavity flow fields using pressure data obtained in the Langley 0.3-Meter Transonic Cryogenic Tunnel

Static and fluctuating pressure distributions were obtained along the floor of a rectangular-box cavity in an experiment performed in the LaRC 0.3-Meter Transonic Cryogenic Tunnel. The cavity studied was 11.25 in. long and 2.50 in. wide with a variable height to obtain length-to-height ratios of 4.4, 6.7, 12.67, and 20.0. The data presented herein were obtained for yaw angles of 0 deg and 15 deg over a Mach number range from 0.2 to 0.9 at a Reynolds number of 30 x 10(exp 6) per ft with a boundary-layer thickness of approximately 0.5 in. The results indicated that open and transitional-open cavity flow supports tone generation at subsonic and transonic speeds at Mach numbers of 0.6 and above. Further, pressure fluctuations associated with acoustic tone generation can be sustained when static pressure distributions indicate that transitional-closed and closed flow fields exist in the cavity. Cavities that support tone generation at 0 deg yaw also supported tone generation at 15 deg yaw when the flow became transitional-closed. For the latter cases, a reduction in tone amplitude was observed. Both static and fluctuating pressure data must be considered when defining cavity flow fields, and the flow models need to be refined to accommodate steady and unsteady flows.

Tracy, M. B.↗
NASA NTRS1929

Forces on Elliptic Cylinders in Uniform Air Stream

This report presents the results of wind tunnel tests on four elliptic cylinders with various fineness ratios, conducted in the Navy Aerodynamic Laboratory, Washington. The object of the tests was to investigate the characteristics of sections suitable for streamline wire which normally has an elliptic section with a fineness ratio of 4.0; also to learn whether a reduction in fineness ratio would result in improvement; also to determine the pressure distribution on the model of fineness ratio of 4. Four elliptic cylinders with fineness ratios of 2.5, 3.0, 3.5, and 4.0 were made and then tested in the 8 by 8 wind tunnel; first, for cross-wind force, drag, and yawing moment at 30 miles an hour and various angles of yaw; next for drag 0 degree pitch and 0 degree yaw and various wind speeds; then for end effect on the smallest and largest models; and lastly for pressure distribution over the surface of the largest model at 0 degree pitch and 0 degree yaw and various wind speeds. In all tests, the length of the model was transverse to the current. The results are given for standard air density, p = .002378 slug per cubic foot. This account is a slight revised form of report no. 315. A summary of conclusions is given at the end of the text. (author)

Zahm, A F↗
NASA NTRS1979

The design of supercritical wings by the use of three-dimensional transonic theory

A procedure was developed for the design of transonic wings by the iterative use of three dimensional, inviscid, transonic analysis methods. The procedure was based on simple principles of supersonic flow and provided the designer with a set of guidelines for the systematic alteration of wing profile shapes to achieve some desired pressure distribution. The method was generally applicable to wing design at conditions involving a large region of supercriterical flow. To illustrate the method, it was applied to the design of a wing for a supercritical maneuvering fighter that operates at high lift and transonic Mach number. The wing profiles were altered to produce a large region of supercritical flow which was terminated by a weak shock wave. The spanwise variation of drag of this wing and some principles for selecting the streamwise pressure distribution are also discussed.

Mann, M. J.↗
NASA NTRS1983

Calculation of symmetric vortex separation affecting subsonic bodies at high incidence

A method for calculating the longitudinal aerodynamic coefficients and the pressure distributions on a body at reasonably high angles of attack is presented. The body is represented by a combination of source elements and vortex-lattice elements, including separation of the vortices at increasing angles of attack. The method is self-consistent in that the body and the separated vortex wake are treated as an integrated interacting system. The location of the separation line can be included as an arbitrary input from experimental data or can be evaluated approximately by a pressure-dependent criterion. Calculated values of the aerodynamic coefficients and pressure distributions on cone-cylinder and ogive-cylinder bodies compare well, qualitatively and quantitatively, with experimental data, including simulation of the dependence on Reynolds number.

Almosnino, D.↗
NASA NTRS1995

Analysis of in-flight boundary-layer state measurements on a subsonic transport wing in high-lift configuration

Flight experiments on NASA Langley's B737-100 (TSRV) airplane have been conducted to document flow characteristics in order to further the understanding of high-lift flow physics, and to correlate and validate computational predictions and wind-tunnel measurements. The project is a cooperative effort involving NASA, industry, and universities. In addition to focusing on in-flight measurements, the project includes extensive application of various computational techniques, and correlation of flight data with computational results and wind-tunnel measurements. Results obtained in the most recent phase of flight experiments are analyzed and presented in this paper. In-flight measurements include surface pressure distributions, measured using flush pressure taps and pressure belts on the slats, main element, and flap elements; surface shear stresses, measured using Preston tubes; off-surface velocity distributions, measured using shear-layer rakes; aeroelastic deformations of the flap elements, measured using an optical positioning system; and boundary-layer transition phenomena, measured using hot-film anemometers and an infrared imaging system. The analysis in this paper primarily focuses on changes in the boundary-layer state that occurred on the slats, main element, and fore flap as a result of changes in flap setting and/or flight condition. Following a detailed description of the experiment, the boundary-layer state phenomenon will be discussed based on data measured during these recent flight experiments.

vanDam, C. P.↗