SEARCH · Search NASA

Results for “RAMAN SPECTROSCOPY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Stress- and Time-Dependent Formation of Self-Lubricating In Situ Carbon (SLIC) Films on Catalytically-Active Noble Alloys

Abstract Low shear strength (30 MPa) organic films were grown in situ on Pt 0.9 Au 0.1 surfaces via cyclic sliding contact in dry N 2 with trace concentrations of ambient hydrocarbons. We present a systematic investigation of the stress- and time-dependent film formation. Steady-state friction coefficients were found to be as low as µ ~ 0.015 and inversely proportional to contact pressure, revealing non-Amontonian behavior. Above a Hertzian contact pressure of ~500 MPa, shear strength dropped, indicating an activated process. Raman spectroscopy identified non-uniformity in areal coverage and relative order with contact pressure. Regions of steady-state low-friction behavior exhibited spectra similar to DLC coatings. Atomic force microscopy was used to study the formation and growth of films at the nanoscale. Stress- and time-dependent measurements suggested a sublinear increase of film volume with time, and a transition from growth to wear at a Hertzian contact pressure of ~1.2 GPa.

Jones, Morgan R.↗

DOE OSTI2025

Paper or Plastic? Multiscale Material Handling Properties of Two Model Municipal Solid Waste Streams

Purpose: Municipal Solid Waste (MSW) is a potentially valuable sustainable feedstock for fuel and chemical production due to its carbon-rich content and low cost. This study aims to assess the material handling properties of paperand plastic-rich MSW feedstocks to mitigate equipment failure and processing downtime. Methods: The material handling properties of crumbled MSW feedstocks were measured using apowder rheometer with mass flow hopper calculations to assess handling performance. Inverse gas chromatography was use to measure the surface energy differences between feedstocks. Electron microscopy and Raman spectroscopy was used to evaluate microscale features that may contribute to material handling differences. Results: Plastic and paper rich feedstocks crumbled to a nominal 2 mm particle size were observed to have similar flow and handling characteristics with reasonable hopper outlets. 2 mm plastic rich crumbles, with their higher bulk density, exhibited superior flow performance. By contrast, 4 mm material required significantly larger hopper outlets, indicating poor flowability. Paper rich and 4 mm plastic rich samples displayed broad particle size distributions, which contributed to particle interlocking, jamming, and other flow issues. Electron microscopy revealed that plastic rich samples were significantly smoother, enhancing their flowability compared to the rougher, paper rich materials. Conclusions: This study establishes critical material handling baselines for processing MSW as a viable feedstock for fuel and chemical production. The findings highlight the importance of optimizing particle size and feedstock composition to improve flowability and handling performance.

09 BIOMASS FUELS↗

DOE OSTI2026

Influence of thermal treatment on structure and catalytic performance of ceria-zirconia supported copper oxide (CuO x /Ce y Zr 1-y O 2 ) catalysts for CO oxidation

Copper oxide (CuO x ) supported on ceria-zirconia (Ce y Zr 1-y O 2 , y = 1.0, 0.5, 0.0) catalysts were investigated to elucidate the effects of thermal treatment on their physicochemical properties and catalytic performance in carbon monoxide (CO) oxidation. Here, the catalysts were synthesized via a one-pot chemical vapor deposition (OP-CVD) method at 700˚C and 900˚C with controlled Cu loading. Characterization techniques, including synchrotron X-ray diffraction (S-XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), inductively coupled plasma spectroscopy (ICP), and N 2 adsorption-desorption, were implemented to probe the crystalline structure, molecular and electronic structure, oxygen vacancies, specific surface area (SSA) and metal loading. CO oxidation was chosen as a model reaction to explore the structure-catalytic performance relationship. A ∼100% CO conversion was achieved at < 150˚C, particularly with the CuO x /CeO 2 catalyst calcined at 700˚C. In contrast, calcination at 900˚C caused a ∼90% decrease in SSA and a ∼24% increase in T 50 . Activity tests revealed that increasing ZrO 2 content lowered CO oxidation activity despite generating more defect sites. In-situ measurement of the 700 °C calcined samples revealed the presence of stable and unstable defects in CuO x /Ce 0.5 Zr 0.5 O 2 and CeO 2 respectively, which play a key role in the activity of the catalysts. The results highlight that catalytic performance is closely related to the SSA. Furthermore, an optimum calcination temperature favor significant oxygen vacancy formation with required CuO x -support interactions, enhancing redox properties and catalytic performance.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Precisely doping the surface of tin-based electrocatalysts for improved CO 2 conversion to liquid chemicals

Doping tin catalysts with sulfur can improve the electrochemical CO 2 conversion into formate/formic acid, but the lack of composition-dependent activity trends hinders further catalyst development. Here, we precisely controlled the composition of sulfur-doped Sn catalysts to show that sulfur doping only improves CO 2 conversion over a very narrow composition range, achieving maximum activity at 1.4 at% S. In situ Raman spectroscopy indicted working catalysts were in a primarily metallic state (e.g. S-Sn), and we achieved some of the highest reported partial current densities in both H-cell and full-cell electrolyzer configurations. Density Functional Theory calculations predicted S atoms preferentially occupied the catalyst surface and improved CO 2 reduction by localizing charge density at the catalyst/intermediate interface, which stabilized the *OCOH intermediate and lowered the CO 2 conversion thermodynamic barrier. Our work quantifies the composition-dependent influence of S dopants on Sn-based CO 2 reduction catalysts and provides a pathway for maximizing their CO 2 conversion activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

A highly oxygen reduction reaction active and CO 2 durable high-entropy cathode for solid oxide fuel cells

One big obstacle for the oxygen reduction reaction (ORR) electrode in solid oxide fuel cells (SOFCs) is the poor reaction activity and fast degradations caused by CO 2 poisoning. Here, in this study, we report our design of an active A-site Ca-rich high-entropy Pr 0.1875 Ba 0.1875 Sr 0.1875 La 0.1875 Ca 0.25 CoO 3-δ (PBSLC 25 C) electrode, guided by the O p-band theory. Here, when applied as a cathode in solid oxide fuel cells (SOFCs), it demonstrates high ORR activity and excellent CO 2 tolerance under realistic operating conditions. Ni-YSZ-based anode-supported cells with PBSLC 25 C cathodes demonstrate excellent peak power densities of 1.14 W cm -2 , 1.04 W cm -2 , and 0.77 W cm -2 in the air with 1%, 5%, and 10% CO 2 , respectively, at 750 °C. The engineered high-entropy PBSLC 25 C effectively diminishes the CO 2 poisoning effect and maintains active surfaces for fast oxygen exchange, as confirmed by the cell durability test in air containing CO 2 (5 and 10 vol%), Raman spectroscopy, and density functional theory calculations.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2024

Understanding the Origin of Negative Temperature Dependence and Activity of N-Coordinated Cobalt Sites During Ethylene Dimerization

The on-demand production of short-chain linear alpha olefins (LAOs; C4-C8) via C2H4 dimerization and oligomerization is industrially attractive, prompting extensive research on designing active, selective, and stable catalysts for industrial use. Cobalt supported on ammoniated carbon (Co(NH3)x/C) catalysts have shown remarkable activity and selectivity in this process. However, critical aspects such as the active phase, active site structure, the role of the catalyst support, cobalt loading effects, and the inverse correlation of the reaction rate with temperature remain inadequately understood. This study systematically explores these factors using a combination of steady-state differential catalytic tests, in situ molecular characterization including diffuse reflectance UV-Vis (DR-UV-Vis), Infrared, and Raman spectroscopies, and ex situ X-ray diffraction (XRD) and high annular aberration-corrected dark field transmission electron microscopy (HAADF-STEM). Various supports (SiO2, Al2O3, NH4-ZSM-5, g-C3N4, and C) and cobalt loadings (1.0-3.0 Co nm-2) were studied to determine the optimal catalyst composition and identify the active phase and sites. Carbon-supported catalysts uniquely produce C4-8 LAOs during C2H4 dimerization, with site-time-yield remaining constant (~10-3 s-1) for 1.0-4.0 Co nm-2 at prolonged reaction times (24-48?h time-on-stream). At higher loadings of 6.0 Co nm-2, the formation of crystalline CoO and Co3O4 phases reduces catalytic activity and LAO selectivity. Our findings show that active catalysts lack crystalline cobalt oxides and instead feature dispersed Co2+ sites, tetra-coordinated to a mix of N/NH3 and O/H2O ligands, which catalyze C2H4 dimerization via the Cossee-Arlman mechanism, exhibiting 1st order dependence on C2H4 concentration. The observed inverse rate-temperature correlation is attributed to compensation effects (i.e., presence of Cremer-Constable relationship) linked to changes in adsorption enthalpic and entropic factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Laser-induced digital oxidation for copper-based flexible photodetectors

Copper oxide compounds (Cu x O) with bandgaps of 1.3–2.1 eV (CuO) and 2.1–2.6 eV (Cu 2 O) have been investigated as promising p-type semiconducting materials. Cu x O is generally obtained by deposition or thermal oxidation, but those methods are not optimal for flexible substrates. Furthermore, additional patterning steps are required to fabricate devices. In this work, we present an easy, controllable method to fabricate a metal-semiconductor-metal (MSM) photodetector using laser-induced oxidation of a thin Cu film. After laser irradiation, the Cu film is heated under ambient conditions, and this leads to a thermal oxidation reaction, in which Cu oxide is monolithically formed in the Cu film and a Cu-Cu x O-Cu MSM structure is produced. Since the laser offers localized heating, an arbitrary CuxO pattern can be written in the Cu film by spatially controlled heating. In addition, by optimizing the heating time, the laser-induced oxidation can be successfully performed even on a flexible substrate. To study the laser-induced oxidation, we examined the correlation between laser parameters and the oxidation pattern and analyzed the composition using scanning electron microscopy, Raman spectroscopy, and X-ray photoemission spectroscopy. Furthermore, we measured the transient photoresponse and employed scanning photocurrent microscopy to investigate the mechanism of carrier transport behavior.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Mixed Tin-Titanium Oxides by Atomic Layer Deposition on Planar Substrates: Physical and Electronic Structure

Ternary atomic layer deposition of Sn-doped TiO x (Sn:TiO x ) and Ti-doped SnO x (Ti:SnO x ) was performed using tetrakisdimethylamidotitanium (IV) and tin(IV) with water at 150 °C on (1 0 0) Si and quartz substrates. The physical structure of the films was investigated using scanning electron, atomic force, and Kelvin probe force microscopies as well as spectroscopic ellipsometry, Raman spectroscopy, and X-ray diffraction. All as-deposited films are amorphous and possessed flat and conformal topographies with low surface roughness (<1 nm). Annealed Sn:TiO x and Ti:SnO x crystallize into the tetragonal anatase TiO 2 and cassiterite SnO 2 structures, respectively, without large variations to the film topography. The chemical composition of the as-deposited and annealed films was investigated through X-ray photoelectron spectroscopy. While dopants are homogenously mixed, the ternary ALD to form Sn:TiO x and Ti:SnO x surprisingly does not follow the rule of mixtures, despite similarities in both the growth rates of binary SnO x and TiO x and the precursors used. This finding is also supported by spectroscopic ellipsometry. Here, we postulate the deviation from the rule of mixtures is due to non-ideal surface chemistry of the binary ALD of SnO x . The optical bandgap of all films was quantified by the Tauc analysis and the valence band position was investigated by valence band X-ray photoelectron spectroscopy. Intra-bandgap states above the valence band maximum were observed for as-deposited Ti:SnO x and Sn:TiO x and ascribed to 5 s states from Sn 2+ ions. The presence of these intra-bandgap states induces enhanced visible absorption and bathochromic shifts to the apparent bandgap for all as-deposited films. Annealing the films removes the intra-bandgap states and increases the optical bandgap. Simplified band diagrams created using the data available demonstrated that the conduction and valence band positions did not vary between the positions of pure TiO 2 or SnO 2 with monotonic increases to the dopant incorporation.

36 MATERIALS SCIENCE↗

DOE OSTI2027

Low thermal budget dopant activation in shallow junctions of implanted Si via Tunable plasma enhanced annealing

Low thermal budget (LTB) annealing has become increasingly critical for shallow junctions as semiconductor devices are scaled down. Plasma Enhanced Annealing (PEA) has emerged as a promising LTB annealing process, however its mechanisms remain unclear. In this study, arsenic and boron implanted silicon wafers were subjected to helium or argon ion bombardment generated by annealing plasmas under controlled ion energies and doses in a home-built annealing reactor. The structural and electrical changes were characterized by four-point probe measurements, secondary ion mass spectrometry, Raman spectroscopy and spectroscopic ellipsometry. A pronounced reduction in sheet resistance, accompanied by a decrease in the damage layer thickness demonstrates the surface selective annealing capability of PEA process. Comparative studies using He and Ar plasmas and related ion bombardment reveal a dependence of activation efficacy on both ion species and the dopant implantation profile. Furthermore, a multi-step annealing mechanism is proposed, consisting of an initial (low dose) structural recovery stage followed by the generation of “extended” defects and concluded at large doses by an enhanced dopant activation. The proposed annealing kinetics are thought to be controlled by ion flux, dose and energy. Finally, these results highlight PEA as an effective, surface-selective, LTB approach for shallow-dopant activation and near surface annealing, and provide mechanistic insights into PEA processes.

dopant activation↗

DOE OSTI2021

High hydrogen coverage on graphene via low temperature plasma with applied magnetic field

The chemical functionalization of two-dimensional materials is an effective method for tailoring their chemical and electronic properties with encouraging applications in energy, catalysis, and electronics. One exemplary 2D material with remarkable properties, graphene, can be exploited for hydrogen storage and large on/off ratio devices by hydrogen termination. In this work, we describe a promising plasma-based method to provide high hydrogen coverage on graphene. A low pressure (~10 mtorr) discharge generates a fine-tunable low-temperature hydrogen-rich plasma in the applied radial electric and axial magnetic fields. Post-run characterization of these samples using Raman spectroscopy and X-ray photoelectron spectroscopy demonstrates a higher hydrogen coverage, 35.8%, than the previously reported results using plasmas. Plasma measurements indicate that with the applied magnetic field, the density of hydrogen atoms can be more than 10 times larger than the density without the magnetic field. With the applied electric field directed away from the graphene substrate, the flux of plasma ions towards this substrate and the ion energy are insufficient to cause measurable damage to the treated 2D material. As a result, the low damage allows a relatively long treatment time of the graphene samples that contributes to the high coverage obtained in these experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Flash graphene from rubber waste

Most conventional production processes for graphene are time-consuming, solvent-intensive, and energetically demanding. To circumvent these limitations for mass production, flash Joule heating (FJH) has been shown to be an effective method to synthesize graphene. Here, methods for optimizing production of graphene from rubber waste feedstocks are shown. Through careful control of system parameters, such as pulse voltage and pulse time, turbostratic flash graphene (tFG) can be produced from rubber waste. It is characterized by Raman spectroscopy, X-ray diffraction and thermogravimetric analysis. Here, the resulting tFG can be easily exfoliated and dispersed into various solvents because of its turbostratic arrangement. Addition of tFG into Portland cement results in a significant increase in the compressive strength of the composite. From a materials perspective, FJH offers a facile and inexpensive method for producing high quality tFG from rubber waste materials, which would otherwise be disposed of in landfills or burned for fuel. FJH allows for upcycling of low-value rubber waste into high-value carbon nanomaterials for use as reinforcing additives.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Soot-particle core-shell and fractal structures from small-angle X-ray scattering measurements in a flame

We have characterized soot particles measured in situ in a laminar co-flow ethylene-air diffusion flame using small-angle X-ray scattering (SAXS). The analysis includes temperature measurements made with coherent anti-Stokes Raman spectroscopy (CARS) and complements soot volume-fraction and maturity measurements made with laser-induced incandescence (LII). We compared the results of fits to the SAXS measurements using a unified model and a fractal core-shell model. Power-law parameters yielded by the unified model indicate that aggregates of primary particles are in the mass-fractal regime, whereas the primary particles are in the surface-fractal regime in the middle of the flame. Higher and lower in the flame, the primary-particle power-law parameter approaches 4, suggesting smooth primary particles. Furthermore, these trends are consistent with fits using the fractal core-shell model, which indicate that particles have an established core-shell structure in the middle of the flame and are internally homogeneous at higher and lower heights in the flame. Primary-particle size distributions derived using the fractal core-shell model demonstrate excellent agreement with distributions inferred from transmission electron microscopy (TEM) images in the middle of the flame. Higher in the flame, a second small mode appears in the size distributions, suggesting particle fragmentation during oxidation. Surface oxidation would explain (1) aggregate fragmentation and (2) loss of core-shell structure leading to smoother primary-particle surfaces by removal of carbon overlayers. SAXS measurements are much more sensitive to incipient and young soot particles than LII and demonstrate significant volume fraction from particles low in the flame where the LII signal is negligible.

42 ENGINEERING↗

DOE OSTI2025

Inkless, dry printing nanographene via in-Situ Coordinated laser ablation and sintering processes

Printing carbon, such as graphene and other carbon structures, for flexible and printed electronics currently relies on either ink-based printing, laser-induced forward transfer (LIFT), or laser-induced graphitization (LIG) to convert carbon-rich precursor materials, such as polymers, to graphene-like carbon structures. Liquid inks contain toxic solvents, surfactants, and stabilizing additives that degrade electrical conductivity and require high-temperature post-processing. On the other hand, LIG is limited by the substrate. Here, this study introduces an additive manufacturing method for dry-printing carbon nanomaterials, ranging from amorphous carbon to crystalline graphene-like structures, on various substrates. The system utilizes laser ablation of a solid graphite target to create pure carbon nanoparticles in situ and on demand. An inert gas carries the nanoparticles onto the substrate, where they can be deposited either as amorphous structures or laser-sintered in real time to form various graphitic structures. The study of laser processing parameters, specifically fluence and pulse repetition frequency, revealed three unique regimes of nanostructure evolution that influence the morphological and electrical properties of these printed structures. Raman spectroscopy confirmed graphitization with a resistivity slightly higher than that of the bulk graphite target. The conductivity/resistivity could be tuned as a function of sintering laser power. Scanning transmission electron microscopy (STEM) revealed that turbostratic nanographene formed with an interlayer spacing of 0.40 nm. Despite ink-based printing methods, such as screen printing, inkjet printing (IJP), and aerosol jet printing (AJP), this eco-friendly and green manufacturing technique could eliminate toxic chemicals, reduce environmental impact, and enable single-step fabrication of carbon-based devices for applications in wearable sensors, energy storage, flexible electronics, and Internet of Things (IoT) devices.

Additive nanomanufacturing↗

DOE OSTI2022

Revealing the interplay between “intelligent behavior” and surface reconstruction of non-precious metal doped SrTiO 3 catalysts during methane combustion

The impact of surface reconstruction of a model perovskite, SrTiO 3 (STO), on CH 4 activation for combustion and oxidative coupling was previously revealed that the reaction rate was proportional to the creation of Srterminated step sites. Doped perovskites (SrTi 1-x M x O 3 , M=metal dopant) present yet another form of reconstruction throughout the surface and the bulk, where the metal dopant can migrate in and out of the perovskite lattice, also known as "intelligent behavior". In this work, understanding the interplay between perovskite surface reconstruction (surface termination) and the "intelligent behavior" is tackled for the first time, and the catalytic consequences are probed with CH 4 combustion as a model reaction. A set of experimental techniques, including XRD, Raman spectroscopy, X-ray adsorption spectroscopy, kinetic measurements, as well as DFT calculations were used to understand the catalytic behavior of the reconstructed surfaces of Ni and Cu-doped STO for methane combustion. Here, we found that during methane oxidation, the diffusion of Ni and Cu into the lattice due to the "intelligent behavior" is accompanied by Sr enrichment on the surface of the perovskite. This Srenrichment process is reversible when Cu or Ni species exsolute as clusters/nanoparticles upon H 2 treatment. Such a surface reconstruction is found to greatly impact the catalytic activity of doped perovskites towards methane combustion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

LaNi x Fe 1–x O 3 as flexible oxygen or carbon carriers for tunable syngas production and CO 2 utilization

The current study reports LaFe 1–x Ni x O 3–δ redox catalysts as flexible oxygen or carbon carriers for CO2 utilization and tunable production of syngas at relatively low temperatures (~700 °C), in the context of a hybrid redox process. Specifically, perovskite-structured LaFe 1–x Ni x O 3–δ with seven different compositions (x = 0.4–1) were prepared and investigated. Cyclic experiments under alternating methane and CO 2 flows indicated that all the samples exhibited favorable reactive performance: CH 4 and CO 2 conversions varied between 85% and 98% and 70–88%, respectively. While H 2 /CO ratio from Fe-rich redox catalysts was ~2.3:1 in the methane conversion step, Ni-rich catalysts produced a concentrated (~ 93.7 vol%) hydrogen stream via methane cracking. The flexibility of LaFe 1–x Ni x O 3–δ to produce syngas (or hydrogen) with tunable compositions was found to be governed by the iron/nickel (Fe/Ni) ratio. Redox catalysts with higher Fe contents act as a lattice oxygen carrier via chemical looping partial oxidation (CLPOx) of methane whereas those with higher Ni contents function as a carbon carrier via chemical looping methane cracking (CLMC) scheme. XRD analysis and temperature-programmed reactions revealed that both types of catalysts involve the formation of La 2 O 3 and Ni 0 /Ni-Fe phases under the methane environment. The ability to re-incorporate La 2 O 3 and Ni/Fe into a perovskite structure gives rise to oxygen-carrying capacity whereas stable Ni 0 or Ni/Fe phases would catalyze methane cracking without lattice oxygen exchange in the reaction cycles. Here, temperature programmed oxidation and Raman spectroscopy indicated the presence of graphitic and amorphous carbon species, which were effectively gasified by CO 2 to produce concentrated CO. Stability tests over LaFe 0.5 Ni 0.5 O 3 and LaNiO 3 revealed that the redox performance was stable over a span of 50 cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Microwave catalytic conversion of acetylene for co-production of hydrogen and carbon nanotubes

Natural gas conversion to hydrogen and solid carbon can drastically reduce the carbon footprint. Microwave plasma pyrolysis is an emerging process for chemical industries to directly convert methane (CH 4 ), the major component of natural gas, to hydrogen and carbon, which offers benefits such as fast process dynamics, flexibility, and high product yield. However, the formation of unwanted by-products, like acetylene (C 2 H 2 ), will require extra cost for gas separation. Plasma pyrolysis of CH 4 produces large amount of acetylene at downstream, which is currently used mainly for welding. Here, to avoid gas separation and upgrade acetylene from the downstream of methane plasma reactor, a novel approach toward its transformation to carbon nanotubes (CNT) and pure hydrogen (H 2 ) over Ni-based bimetallic catalyst driven by microwave irradiation has been reported in this work. The dominant gas product was hydrogen. Low concentrations of methane, ethane, and ethylene were observed in the product stream. Catalytic acetylene decomposition was carried out at 400 °C over Al 2 O 3 supported Ni catalyst. The results showed that, at 400 °C, acetylene was dehydrogenated to CNT and hydrogen was the dominant gas in product stream over 10Ni-1Pd-Al 2 O 3 catalyst. Characterizations of spent catalysts was conducted using Raman spectroscopy and transmission electron microscopy (TEM) to investigate the properties of carbon deposited over the catalyst during the catalytic acetylene decomposition. The results highlight that methane can be efficiently converted to hydrogen and CNT through 2-step process, microwave plasma and microwave catalytic conversion of intermediate acetylene, operated in a single reactor system driven by microwave.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Phonon-mediated lipid raft formation in biological membranes

Short-wavelength collective molecular motions, also known as phonons, have recently attracted much interest in revealing dynamic properties of biological membranes through the use of neutron and x-ray scattering, infrared and Raman spectroscopies, and molecular dynamics simulations. Experimentally detecting unique vibrational patterns such as, shear phonon excitations, viscoelastic crossovers, transverse acoustic phonon gaps, and continuous and truncated optical phonon modes in cellular membranes, to name a few, has proven non-trivial. Here, we review recent advances in liquid thermodynamics that have resulted in the development of the phonon theory of 1 liquids. The theory has important predictions regarding the shear vibrational spectra of fluids, namely the emergence of viscoelastic crossovers and transverse acoustic phonon gaps. Furthermore, we show that these vibrational patterns are common in soft (non-crystalline) materials, including, but not limited to liquids, colloids, liquid crystals (mesogens), block copolymers, and biological membranes. The existence of viscoelastic crossovers and acoustic phonon gaps define the self-diffusion properties of cellular membranes and provide a molecular picture of the transient nature of lipid rafts.1 Importantly, the timescales (picoseconds) for the formation and dissolution of transient lipid rafts match the lifetime of the formation and breakdown of interfacial water hydrogen bonds. Apart from acoustic propagating phonon modes, biological membranes can also support more energetic non-propagating optical phonon excitations, also known as standing waves or breathing modes. Importantly, optical phonons can be truncated due to the existence of finite size nanodomains made up of strongly correlated lipid-cholesterol molecular pairs. These strongly coupled molecular pairs can serve as nucleation centers for the formation of stable rafts at larger length scales, due to correlations of spontaneous fluctuations (Onsager’s regression hypothesis). Finally and importantly, molecular level viscoelastic crossovers, acoustic phonon gaps, and continuous and truncated optical phonon modes may offer insights as to how lipid-lipid and lipid-protein interactions enable biological function.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗