Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reaction Control System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Attitude and translation control of a low-altitude Gravsat

Dynamic simulation of the Gravsat's attitude and translation control system is used to provide an upper bound for the fuel supply and test the feasibility of the preliminary design. A preliminary design is made for the disturbance compensation system (DISCOS) sensor, the thruster control laws, reaction wheel control laws, and the onboard state estimators. The sensor analysis and noise measurements show no problems in scaling the Triad navigation satellite sensor design up to meet the Gravsat requirements, except for proof mass center-of-mass offset. A promising technique is proposed to measure and eliminate this error. The covariance analysis confirms that a sophisticated post-flight data fit will be necessary to reconstruct a scientifically useful proof mass state. The DISCOS sensor will have to be continuously calibrated from the inflight data to achieve this reconstruction.

Ray, J. C.↗
NASA NTRS1986

Space Telescope precision pointing control system

The Hubble Space Telescope has the most stringent pointing requirements imposed on any spacecraft to date. The overall HST stability shall not exceed 0.007 arc-seconds rms. The Pointing Control System utilizes fine guidance sensors and rate gyros for attitude reference and rate information. Control torques are provided by reaction wheels. A digital computer collects the sensor data, performs the control law computations, and sends torque commands to the reaction wheels. To attain this precision pointing, improvements were made to the rate gyros to lower their noise characteristics and to the reaction wheels to reduce their emitted vibration levels. The control system design was validated in a test sequence which progressed from model verification tests on an air-bearing to operations-oriented, closed loop testing on the assembled vehicle. A test system is described which allowed the simultaneous production of test case command loads for the flight computer and plots of predicted profiles to assist in test data analysis. Workarounds were required during system test to accommodate gyro biases and noise introduced into the closed loop system. Testing and analysis indicate that the HST will provide the capability to meet the requirements for precision pointing.

Beals, G. A.↗
NASA NTRS1992

Geostationary Operational Environmental Satellite (GOES-N report). Volume 2: Technical appendix

The contents include: operation with inclinations up to 3.5 deg to extend life; earth sensor improvements to reduce noise; sensor configurations studied; momentum management system design; reaction wheel induced dynamic interaction; controller design; spacecraft motion compensation; analog filtering; GFRP servo design - modern control approach; feedforward compensation as applied to GOES-1 sounder; discussion of allocation of navigation, inframe registration and image-to-image error budget overview; and spatial response and cloud smearing study.

Source record↗
NASA NTRS1990

Optical alignments of the Cosmic Background Explorer (COBE) observatory

The angular alignments and stabilities of multiple components in a single coordinate system were determined using various alignment tooling techniques. These techniques use autocollimation measurements with a first order theodolite and transformation of coordinates to determine the relative alignment between various components with respect to a common set of COBE spacecraft coordinate axes. Optical-mechanical alignment techniques were also used to integrate the flight COBE observatory attitude control system module that consists of gyros, reaction wheels, and a momentum wheel. Particular attention is given to the techniques for alignments and stabilities of the earth scanners, sun sensors, far IR absolute spectrophotometer, Diffuse Infrared Background Experiment, and differential microwave radiometer antenna horn boresights.

Sampler, Henry P.↗
NASA NTRS2016

Pattern Recognition Control Design

Spacecraft control algorithms must know the expected spacecraft response to any command to the available control effectors, such as reaction thrusters or torque devices. Spacecraft control system design approaches have traditionally relied on the estimated vehicle mass properties to determine the desired force and moment, as well as knowledge of the effector performance to efficiently control the spacecraft. A pattern recognition approach can be used to investigate the relationship between the control effector commands and the spacecraft responses. Instead of supplying the approximated vehicle properties and the effector performance characteristics, a database of information relating the effector commands and the desired vehicle response can be used for closed-loop control. A Monte Carlo simulation data set of the spacecraft dynamic response to effector commands can be analyzed to establish the influence a command has on the behavior of the spacecraft. A tool developed at NASA Johnson Space Center (Ref. 1) to analyze flight dynamics Monte Carlo data sets through pattern recognition methods can be used to perform this analysis. Once a comprehensive data set relating spacecraft responses with commands is established, it can be used in place of traditional control laws and gains set. This pattern recognition approach can be compared with traditional control algorithms to determine the potential benefits and uses.

Gambone, Elisabeth↗
NASA NTRS2018

Pattern Recognition Control Design

Spacecraft control algorithms must know the expected vehicle response to any command to the available control effectors, such as reaction thrusters or torque devices. Spacecraft control system design approaches have traditionally relied on the estimated vehicle mass properties to determine the desired force and moment, as well as knowledge of the effector performance to efficiently control the spacecraft. A pattern recognition approach was used to investigate the relationship between the control effector commands and spacecraft responses. Instead of supplying the approximated vehicle properties and the thruster performance characteristics, a database of information relating the thruster ring commands and the desired vehicle response was used for closed-loop control. A Monte Carlo simulation data set of the spacecraft dynamic response to effector commands was analyzed to establish the influence a command has on the behavior of the spacecraft. A tool developed at NASA Johnson Space Center to analyze flight dynamics Monte Carlo data sets through pattern recognition methods was used to perform this analysis. Once a comprehensive data set relating spacecraft responses with commands was established, it was used in place of traditional control methods and gains set. This pattern recognition approach was compared with traditional control algorithms to determine the potential benefits and uses.

Gambone, Elisabeth A.↗
NASA NTRS1996

STS-78 Flight Day 15

On this fifteenth day of the STS-78 mission, the 4th of July, Cmdr. Terence T. Henricks, Pilot Kevin R. Kregel, Payload Cmdr. Susan J. Helms, Mission Specialists Richard M. Linnehan, Charles E. Brady, Jr., and Payload Specialists Jean-Jacques Favier, Ph.D. and Robert B. Thirsk, M.D., are awakened with Bruce Springsteen's 'Born in the USA' and Lee Greenwood's 'I'm Proud to be an American' to begin another a day on orbit. Mission Commander Tom Henricks responded to Mission Control's wake up call by saying that the five US-born crew members were very proud to be Americans, particularly on the day America celebrates its 220th anniversary. Work in the Spacelab module will continue with investigations into the effects of microgravity on muscle strength and endurance, lung function, and adaptation of the neurovestibular system to a microgravity environment. Henricks and Pilot Kevin Kregel will complete work with a laptop computer designed to test the crew's critical thinking skills and reaction time. They also will test a voice control system that allows them to reposition Columbia's closed-circuit television cameras with verbal cues, keeping their hands free to perform other tasks.

Source record↗
DOE OSTI2023

Concepts Relevant for the Kinetic Analysis of Reversible Reaction Systems

The net rate of a reversible chemical reaction is the difference between unidirectional rates of traversal along forward and reverse reaction paths. In a multistep reaction sequence, the forward and reverse trajectories, in general, are not the microscopic reverse of one another; rather, each unidirectional route is comprised of distinct rate-controlling steps, intermediates, and transition states. Consequently, traditional descriptors of rate (e.g., reaction orders) do not reflect intrinsic kinetic information but instead conflate unidirectional contributions determined by (i) the microscopic occurrence of forward/reverse reactions (i.e., unidirectional kinetics) and (ii) the reversibility of reaction (i.e., nonequilibrium thermodynamics). This review aims to provide a comprehensive resource of analytical and conceptual tools which deconvolute the contributions of reaction kinetics and thermodynamics to disambiguate unidirectional reaction trajectories and precisely identify rate- and reversibility-controlling molecular species and steps in reversible reaction systems. The extrication of mechanistic and kinetic information from bidirectional reactions is accomplished through equation-based formalisms (e.g., De Donder relations) grounded in principles of thermodynamics and interpreted in the context of theories of chemical kinetics developed in the past 25 years. Here, the aggregate of mathematical formalisms detailed herein is general to thermochemical and electrochemical reactions and encapsulates a diverse body of scientific literature encompassing chemical physics, thermodynamics, chemical kinetics, catalysis, and kinetic modeling.

42 ENGINEERING↗
NASA NTRS1982

Space telescope - Meeting the pointing control challenge with today's technology

The pointing control system of the Space Telescope, which provides target-to-target maneuvering capability and precision pointing on the target star (with 0.007-arcsec stability and 0.01-arcsec accuracy), is described. Spacecraft attitude control is undertaken by onboard computer processing of attitude and rate sensor data that generates reaction wheel torque commands. The Space Telescope Operations Control Center communicates with the Space Telescope via the synchronous altitude tracking and data relay satellite system, and determines vehicle attitude more precisely by means of sun sensors, magnetometers and fixed-head star trackers. Such disturbance torques as those of gravity gradients and aerodynamics act on the Space Telescope, causing the speeds of the four reaction wheels to increase. In order to prevent the wheels from reaching a speed-saturated condition, a momentum control system is provided for the management of reaction wheel speed buildup. Attention is given to development testing and control hardware investigations and improvements.

Dougherty, H.↗
NASA NTRS1991

A study of fault injection in multichannel spacecraft power systems

NASA/Marshall Space Flight Center proposes to implement fault injection into an electrical power system breadboard to study the reactions of the various control elements of this breadboard. Among the elements to be studied are the remote power controllers, the algorithms in the control computers, and the artificially intelligent control programs resident in this breadboard. To this end, a study of electrical power is being performed to yield a list of the most common power system faults. The results of this study are being applied to a multichannel high-voltage DC spacecraft power system called the Large Autonomous Spacecraft Electrical Power System Breadboard. Some of the reactions of the breadboard to some of the faults which have been encountered are presented along with the results of this study.

Dugal-Whitehead, Norma R.↗
NASA NTRS1962

NASA Scout ST-1 Flight-Test Results and Analyses, Launch Operations, and Test Vehicle Description

The first of a series of flight tests for the development of the four-stage, solid-propellant Scout vehicle was conducted at the NASA Wallops Station under the direction of the Langley Research Center. Vehicle designation for the test was NASA Scout ST-1. Performance characteristics of the vehicle and components were recorded during a high-altitude probe mission. Flight-simulation studies are presented and show that the accuracy of the guidance system during the flight was within control-system design specifications. The control system functioned normally during the flight with the exception of an overpowering of the reaction-control roll jets near burnout of the third-stage rocket motor. The resulting roll displacement of the vehicle is shown to have caused the monitor tracking radar which had been erroneously tracking a radar beacon in the vehicle on a side lobe to reorient to the major lobe of the receiving antenna. This tracking switch falsely indicated a violent turning maneuver on the monitor plot board and resulted in a hold-fire decision for the fourth-stage rocket motor. Although data for the final thrusting and coast phase of the flight were not obtained, the majority of the test objectives were achieved. In-flight thrust misalignment angles for the second- and third-stage rocket motors derived from control-system error data and for the first-stage motor determined from flight-simulation studies are presented. All rocket-motor thrust misalignment angles were well within the tolerances used for control-system design. Rocket-motor flight performance is presented, and velocity increments attained from the first three stages substantiated the predicted nominal performance. Operation of the rocket motors was satisfactory with the exception of high-level vibrations which were encountered during third-stage motor burning. Rolling moments which overpowered the reaction-control jets are also attributed to the burning characteristics of the third-stage motor. A discussion of the premature loss of the third-stage heat shield is given and shows that the heat-shield latching mechanism failed from pressure loads as the vehicle entered the transonic speed range. Although venting was provided to relieve the high negative pressures known to exist on the heat shield at these speeds, a field modification of the wiring tunnel had the same effect as opening the inside of the heat shield to ambient pressures. Consequently, the latching mechanism failed from pressure loads which were of about the same magnitude as the latching-mechanism yield loads. Skin temperatures were recorded at several locations on the vehicle and were generally in good agreement with theoretical values. Aerodynamic heating presented no problem during the flight since the maximum temperatures recorded during the flight were only about half the design values because of the high-launch-angle trajectory. Environmental vibrations recorded in the vicinity of the guidance package showed that no significant continuous amplitude levels above the general instrumentation noise level were present during first- and second-stage burning. Large vibration amplitudes were recorded during third-stage burning which coincided with the large roll disturbance experienced by the vehicle near burnout of the third-stage motor.

Scout Launch Vehicle↗
DOE OSTI2022

Nanopore facilitated monohydrocalcitic amorphous calcium carbonate precipitation

Predicting the precipitation of solids is important in both natural systems and subsurface energy applications. The factors controlling reaction mechanisms, phase selection and conversion between phases are particularly important. In this contribution the precipitation and growth of an amorphous calcium carbonate species from flowing aqueous solution in a nanoporous controlled pore glass is followed in situ with differential X-ray pair distribution function analysis. It is discovered that the local atomic structure of this phase indicates monohydrocalcite-like pair–pair correlations, yet is functionally amorphous because it lacks long-range structure. The unexpected occurrence of synthetic proto-monohydrocalcite amorphous calcium carbonate, precipitated from a solution undersaturated with respect to published solubilities, suggests that nanopore confinement facilitates formation of an amorphous phase at the expense of more favorable crystalline ones. Finally, this result illustrates that confinement and interface effects are physical factors exerting control on mineral nucleation behavior in natural and geological systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2012

NASA Tech Briefs, May 2012

Topics covered include: An "Inefficient Fin" Non-Dimensional Parameter to Measure Gas Temperatures Efficiently; On-Wafer Measurement of a Multi-Stage MMIC Amplifier with 10 dB of Gain at 475 GHz; Software to Control and Monitor Gas Streams; Miniaturized Laser Heterodyne Radiometer (LHR) for Measurements of Greenhouse Gases in the Atmospheric Column; Anomaly Detection in Test Equipment via Sliding Mode Observers; Absolute Position of Targets Measured Through a Chamber Window Using Lidar Metrology Systems; Goldstone Solar System Radar Waveform Generator; Fast and Adaptive Lossless Onboard Hyperspectral Data Compression System; Iridium Interfacial Stack - IrIS; Downsampling Photodetector Array with Windowing; Optical Phase Recovery and Locking in a PPM Laser Communication Link; High-Speed Edge-Detecting Line Scan Smart Camera; Optical Communications Channel Combiner; Development of Thermal Infrared Sensor to Supplement Operational Land Imager; Amplitude-Stabilized Oscillator for a Capacitance-Probe Electrometer; Automated Performance Characterization of DSN System Frequency Stability Using Spacecraft Tracking Data; Histogrammatic Method for Determining Relative Abundance of Input Gas Pulse; Predictive Sea State Estimation for Automated Ride Control and Handling - PSSEARCH; LEGION: Lightweight Expandable Group of Independently Operating Nodes; Real-Time Projection to Verify Plan Success During Execution; Automated Performance Characterization of DSN System Frequency Stability Using Spacecraft Tracking Data; Web-Based Customizable Viewer for Mars Network Overflight Opportunities; Fabrication of a Cryogenic Terahertz Emitter for Bolometer Focal Plane Calibrations; Fabrication of an Absorber-Coupled MKID Detector; Graphene Transparent Conductive Electrodes for Next- Generation Microshutter Arrays; Method of Bonding Optical Elements with Near-Zero Displacement; Free-Mass and Interface Configurations of Hammering Mechanisms; Wavefront Compensation Segmented Mirror Sensing and Control; Long-Life, Lightweight, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration; Reliable Optical Pump Architecture for Highly Coherent Lasers Used in Space Metrology Applications; Electrochemical Ultracapacitors Using Graphitic Nanostacks; Improved Whole-Blood-Staining Device; Monitoring Location and Angular Orientation of a Pill; Molecular Technique to Reduce PCR Bias for Deeper Understanding of Microbial Diversity; Laser Ablation Electrodynamic Ion Funnel for In Situ Mass Spectrometry on Mars; High-Altitude MMIC Sounding Radiometer for the Global Hawk Unmanned Aerial Vehicle; PRTs and Their Bonding for Long-Duration, Extreme-Temperature Environments; Mid- and Long-IR Broadband Quantum Well Photodetector; 3D Display Using Conjugated Multiband Bandpass Filters; Real-Time, Non-Intrusive Detection of Liquid Nitrogen in Liquid Oxygen at High Pressure and High Flow; Method to Enhance the Operation of an Optical Inspection Instrument Using Spatial Light Modulators; Dual-Compartment Inflatable Suitlock; Large-Strain Transparent Magnetoactive Polymer Nanocomposites; Thermodynamic Vent System for an On-Orbit Cryogenic Reaction Control Engine; Time Distribution Using SpaceWire in the SCaN Testbed on ISS; and Techniques for Solution- Assisted Optical Contacting.

Source record↗
DOE OSTI2019

Kinetic Modeling of the Silicothermic Reduction of Manganese Oxide from Slag

A model was developed to describe the mixed rate control kinetics in systems with MnO-SiO{sub 2}-CaO-Al{sub 2}O{sub 3} slags and Fe-Si metal droplets. During the reaction of Fe-Si droplets and slag, Mn{sup 2+} transport was found to be part of controlling the system but could not sufficiently describe all initial conditions (chiefly, changes to initial silicon content). The current model describes the kinetics of the stated system and offers answers to the question of rate control; the model has been fitted to nine datasets of varying initial conditions including initial [Si], initial (MnO), initial droplet size, and reaction temperature. The fitted mass transfer coefficients for metal and slag were 2.3 × 10{sup −4} and 6.7 × 10{sup −4} m/s, respectively; these values are constant across the nine datasets. Previous claims about the efficiency of silicon usage in reducing manganese have been modified; it appears that the formation of silica is favored throughout the reaction, but that the formation of a silicon monoxide gas layer on the metal surface dramatically impacts the rate of reaction. As a measure of overall fit of the model, the average of the root-mean-square errors for all datasets is 14 pct. Mass transport in slag is twice as influential on rate control as the metal phase. The simultaneous transport of both Mn{sup 2+} and silicate dimers controls mass transport in the slag. Both [Si] and [Mn] can control from the metal side but are dependent on the initial conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Toward Spatial Control of Reaction Selectivity on Photocatalysts Using Area-Selective Atomic Layer Deposition on the Model Dual Site Electrocatalyst Platform

Photocatalytic water splitting is a promising route to low-cost, green H 2 . However, this approach is currently limited in its solar-to-hydrogen conversion efficiency. One major source of efficiency loss is attributed to the high rates of undesired side and back reactions, which are exacerbated by the proximity of neighboring oxidation and reduction sites. Nanoscopic oxide coatings have previously been used to selectively block undesired reactants from reaching active sites; however, a coating encapsulating the entire photocatalyst particle limits activity as it cannot facilitate both half-reactions. In this work, area selective atomic layer deposition (AS-ALD) was used to selectively deposit semipermeable TiO 2 films onto model metallic cocatalysts for enhancing reaction selectivity while maintaining a high overall activity. Pt and Au were used as exemplary reduction and oxidation cocatalyst sites, respectively, where Au was deactivated toward ALD growth through self-assembled thiol monolayers while TiO 2 was coated onto Pt sites. Electroanalytical measurements of monometallic thin film electrodes showed that the TiO 2 -encapsulated Pt effectively suppressed undesired H 2 oxidation and Fe(II)/Fe(III) redox reactions while still permitting the desired hydrogen evolution reaction (HER). A planar model photocatalyst platform containing patterned interdigitated arrays of Au and Pt microelectrodes was further assessed using scanning electrochemical microscopy (SECM), demonstrating the successful use of AS-ALD to enable local reaction selectivity in a dual-reaction-site (photo)electrocatalytic system. Finally, interdigitated microelectrodes having independent potential control were used to show that selectively deposited TiO 2 coatings can suppress the rate of back reactions on neighboring active sites by an order of magnitude compared with uncoated control samples.

08 HYDROGEN↗
NASA NTRS1996

Pointing and Scanning Control of Instruments Using Rotating Unbalanced Masses

Motions of telescopes, satellites, and other flight bodies have been controlled by various means in the past. For example, gimbal mounted devices can use electric motors to produce pointing and scanning motions. Reaction wheels, control moment gyros, and propellant-charged reaction jets are other technologies that have also been used. Each of these methods has its advantages, but all actuator systems used in a flight environment face the challenges of minimizing weight, reducing energy consumption, and maximizing reliability. Recently, Polites invented and patented the Rotating Unbalanced Mass (RUM) device as a means for generation scanning motion on flight experiments. RUM devices have been successfully used to generate various scanning motions. The basic principle: a RUM rotating at constant annular velocity exerts a cyclic centrifugal force on the instrument or main body, thus producing a periodic scanning motion. A system of RUM devices exerts no reaction forces on the main body, requires very little energy, and is very simple to construct and control. These are significant advantages over electric motors, reaction wheels, and control moment gyroscopes. Although the RUM device very easily produces scanning motion, an auxiliary control system may be required to maintain the proper orientation, or pointing of the main body. It has been suggested that RUM devices can be used to control pointing dynamics, as well as generate the desired periodic scanning motion. The idea is that the RUM velocity will not be constant, but will vary over the period of one RUM rotation. The thought is that the changing angular velocity produces a centrifugal force having time-varying magnitude and direction. The scope of the present research project is to further study the pointing control concept, and to implement a microcontroller program to control an experimental hardware system. This report is subdivided into three themes. The basic dynamic modeling and control principles are described first. Then, the controller implementation and preliminary test results are discussed. Finally, suggestions for future work are presented.

Hung, John Y.↗
NASA NTRS1985

Payload isolation and precision pointing for the 1990's

The design of a pointing system that is applicable for a variety of payloads is examined. The system employs a very soft interface coupled with inertial control torques which use reaction wheels or control moment gyros. The fundamental stability and disturbance rejection characteristics of simple gimbal pointing systems and the soft mounted inertially reacting concept are evaluated and compared. It is observed that in simple and two-stage gimbal systems there is dynamic interaction with the basebody and these types of systems are not applicable for a Space Station/Space Platform environment in which system dynamics are uncertain; however, the soft mounted inertially reacting concept minimizes the dynamic interaction with the basebody and retains stability. It is concluded that the soft mounted inertially reacting concept has the pointing accuracy and disturbance isolation of a free flying spacecraft while still obtaining power, communication, orbit maintenance, and servicing from a basebody.

Sirlin, S. W.↗