Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reactor Structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Reduction of Ultrafine Hematite for a Spouting Bed Chemical Looping Process - Presentation

Chemical looping combustion research has been a topic of great interest since the mid-1990s, although the concept can be traced much further back. It is a combustion technology for fuel utilization that uses a two-reactor system to produce a carbon free effluent stream from the air reactor and a carbon dioxide rich stream from the fuel reactor with oxygen shuttled between the reactors with an oxygen carrier. Chemical looping combustion has been studied extensively because of this inherent separation of the carbon dioxide combustion product from the atmospheric nitrogen over that past 25 years with hundreds of research papers and tens of books. The oxygen carrier is, in general, a solid such as naturally occurring hematite or an engineered carrier like a copper and iron oxide supported on alumina. System technical and economic research activities conducted at the National Energy Technology Laboratory have shown that the costs associated with the carrier, initial and replacement, are a significant factor in the economic viability of the technology. To overcome this economic challenge, the work reported on in this paper investigates the use of a waste iron oxide as the chemical looping oxygen carrier. This waste material is quite unique as it has a particle size of 0.7 um. Given the particle size, the reactions are quite fast. However, the development of a contactor reactor to mix the fuel with the carrier is a fluidization challenge as the material is a Geldart group C material and highly cohesive. Normally, Geldart group C materials are fluidized with either a vibrating bed. This technique is acceptable for low temperature pharmaceuticals production but does not lend itself to much larger reactors used for power production or operation at temperatures in the order of 1100 to 1200 C. Therefore, a hydrodynamic solution was needed to break up the cohesive structures to replace the vibration. In this instance, it was hypothesized that a spouting bed of large Geldart group B or Geldart group D particles could provide the necessary energy to break up the cohesive structures of the Geldart group C material. This paper presents the reduction performance for this novel carrier material in a laboratory spouting bed reactor.

Breault, Ronald↗
DOE OSTI2026

Structural coherence model for predicting molten salt thermal conductivity informed by the pair distribution function

To enable thermal behavior prediction and design optimization of molten salt reactors, thermal conductivity of molten salts must be characterized in terms of salt composition and temperature. Current theoretical models fail to provide consistent approximations for all halide mixtures, particularly actinide-bearing melts. This study aims to link the short-range order structure of molten salts to the mean free path of energy carriers through a simple structural coherence model informed by the partial pair distribution function. The proposed method is used to predict the thermal conductivity of 33 alkali and alkaline earth halide salts. Predictions approximate experimental measurements with a mean absolute error of 15.7% for dissociating, complexing, and actinide salts, including unary LiCl, NaCl, and MgCl 2 as well as mixtures LiF–NaF–KF (FLiNaK), LiF–BeF 2 (FLiBe), and NaCl–UCl 3 . The work provides evidence for the validity of energy carrier descriptions of molecular-level heat transfer in molten salts, with implications for improved theories of liquid energy transport in general.

Actinide mixtures↗
DOE OSTI2021

Geometric Optimization of an Electrochemical Purification Cell to Prevent Corrosion in CSP Plants During Operation

When exposed to moisture or oxygen, molten chloride salts produce corrosive impurities which degrade containment alloys. As a result, this can significantly decrease the lifetime and increase costs of molten-salt-based systems. To overcome this barrier, we designed and modeled an electrochemical purification cell to remove the corrosive impurity MgOH+. Various reactor architectures, including constant stirred tank reactors (CSTRs) and plug flow reactors (PFRs) were investigated. Steady-state thermoelectric properties were evaluated, allowing assessment of the effects of structure and design parameters such as flow rate, cell length, and cross-sectional area of molten salt. The results suggest that our design could most effectively increase reliability and decrease costs of molten-chloride-salt-based systems by protecting them during continuous operation using an annular plug flow reactor.

chloride salts↗
DOE OSTI2024

01-07 Reactor Supplemental Shielding For the NRIC DOME Test Bed 01-07 Reactor Supplemental Shielding For the NRIC DOME Test Bed 2

A radiation shielding system is needed to protect personnel and equipment from harsh neutron and photon fluxes during: Reactor operations Post shut down operations Disassembly Decommissioning Examples of RSS driving requirements Radiological Controls Operating dose rate: the dose rate during normal reactor operations shall be <0.5 mrem/hr at the exterior wall of DOME containment Outdoor radiation limit: shielding shall provide the dose to a facility worker outside of DOME to <0.05 mrem/hr at 50 ft from the exterior wall of the DOME Temperature Reactors may have operating temperatures up to 800C The RSS shall be capable of removing up to 100 KW of heat during normal operating conditions the concrete structure has an upper temperature limit of 100°C

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1981

Development of a polysilicon process based on chemical vapor deposition (phase 1)

A dichlorosilane-based reductive chemical vapor deposition (CVD) process demonstrated is capable of producing, at low cost, high quality polycrystalline silicon. Testing of decomposition reactor heat shields to insure that the shield provides adequate personnel protection assuming a worst case explosion was completed. Minor modifications to a production reactor heat shield provided adequate heat shield integrity. Construction of the redesigned PDU (Process Development Unit) to accommodate all safety related information proceeded on schedule. Structural steel work was completed as is the piping and instrumentation design work. Major pieces of process equipment were received and positioned in the support structure and all transfer piping and conduits to the PDU were installed. Construction was completed on a feed system for supplying DCS to an intermediate sized reactor. The feed system was successfully interfaced with a reactor equipped with a modified heat shield. Reactor checkout was completed.

Mccormick, J.↗
DOE OSTI2025

Structure evolution and tin redistribution during oxidation of Zircaloy-4 at 500°C

Zirconium (Zr) alloys are widely used as fuel cladding in nuclear power reactors due to their thermal stability, mechanical durability, corrosion resistance, and low neutron absorption cross-section. However, their performance is challenged by oxidation in reactor environments, making the study of Zr alloy corrosion behavior crucial for ensuring the safety, longevity, and economic viability of nuclear power systems. While the oxidation behavior of Zr-based cladding materials has been extensively studied since the 1950s, a mechanistic understanding into the relationship between structure evolution, solute element redistribution, and properties remains elusive. Valuable insights may be obtained through advanced experimental methods, such as in-situ and high resolution microscopy techniques. Here, in this study, the oxidation behavior of Zircaloy-4 at 500 °C in O 2 is characterized using a multimodal advanced characterization approach. Using in-situ X-ray diffraction, the phase evolution from metastable to stable oxides is tracked in real time. Complementary high-resolution techniques, including electron microscopy and atom probe tomography, reveal nanoscale insights into the microstructural changes and solute redistribution across the oxide/metal interface. Nanohardness mapping across the oxide/metal interface highlights localized mechanical property variations that may be linked to changes in microstructure and crystal structure within the oxide layer. These findings offer valuable insights into the microstructure and property evolution of Zircaloy-4 during oxidation, contributing to a better understanding of microstructural changes in Zr-based alloys under oxidative environments.

APT↗
DOE OSTI2024

Investigation of Point-Contact Strategies for CFD Simulations of Pebble-Bed Reactor Cores

This study numerically investigated the effects of various contact strategies on the thermal hydraulic behavior within a structured bed of 100 explicitly modeled pebbles. Four contact strategies and two thermal hydraulic conditions were considered. The strategies to avoid contact singularities include decreasing the pebble diameter, increasing the pebble diameter, bridging the pebble surfaces near the contact region, and capping the pebble surfaces near the contact region. One strategy, Strategy 3a, which involves bridging with a cylinder equal to 10% of the pebble diameter, was selected as the baseline strategy because it addressed the contact singularity while minimizing the geometric changes that affect the bed porosity. The two thermal hydraulic conditions were full-power operation (Case 1) and pressurized loss of forced cooling or PLOFC (Case 2). Simulations of the conjugate heat transfer within the structured bed were performed using the Reynolds-averaged Navier–Stokes approach with the realizable k-ϵ turbulence model and two-layer all y + wall treatment. The thermal-fluid quantities of interest were compared between the contact strategies for each case. In Case 1, the hydraulic behavior was sensitive to the contact strategy, with large differences in the pressure drop (30%) and volume-average velocity (4%). The thermal behavior was not sensitive, with less than a 0.5% difference across the strategies. To better understand the separate effects of each heat transfer mode, Case 2 was divided into the following subcases: conduction (Case 2a); conduction/radiation (Case 2b); and conduction/radiation/convection (Case 2c). Case 2a represents an early phase of the PLOFC transient. Case 2b represents an intermediate phase of the PLOFC transient, with the pebble temperatures sufficiently high for the radiative heat transfer to be non-negligible. Case 2c represents a late phase of the PLOFC transient after the establishment of the natural circulation of the heat transfer fluid. For Case 2, large differences in the contact strategy were observed only in Case 2a with only conduction. The difference in the maximum pebble temperature was 23% in Case 2a, 2% in Case 2b, and 0.3% in Case 2c.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Economic solution for low carbon process heat: A horizontal, compact high temperature gas reactor

In 2018, nuclear energy generated 55% of United States’ and one third of the world’s carbon free electricity, making nuclear energy a key tool in efforts to mitigate climate change before 2050. However, the current nuclear technology, light water reactors (LWRs), is limited to 300°C, so it cannot be used to decarbonize industrial process heat which accounts for 12% of US greenhouse gas emissions. High temperature gas reactors (HTGRs) can meet the high temperature demand with carbon free nuclear heat. The estimated cost of HTGRs, such as the Next Generation Nuclear Plant (NGNP), are even higher than state-of-the-art LWRs. In this paper, we expanded our nuclear cost estimating tool to include HTGRs and find that the NGNP overnight capital costs were 32% higher than an advanced LWR per unit capacity. The higher cost will naturally result in larger risk to cost overrun as recently experienced by larger LWRs in western nations. With a design-to-build mindset to minimize cost and construction risk, we introduce the horizontal, compact HTGR (HC-HTGR). The reactor core and steam generator are mounted horizontally on rails and in-line with one another, decreasing the size of the reactor building relative to the power capacity four times when compared to traditional HTGRs. The HC-HTGR reduced overnight civil structure costs by 42%, indirect costs by 38%, and total capital costs by 20% from NGNP. We discussed the required engineering of new systems for the HC-HTGR including vessel supports, the reactor cavity cooling system, and steam generator design. Finally, we estimated the fuel and operations costs of the HC-HTGR, and a survey of low-carbon industrial process heat technology showed the HC-HTGR can deliver a highly competitive levelized cost of heat in the range of $6.13–12.48/GJ.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Benchmark Study Matrix for Microreactor Geometries Relevant to Multiple Developers

A benchmark study was developed that include design, development, manufacturing, and performance measurement of agnostic reactor relevant geometries to support industry’s adoption of advanced manufacturing in a variety of structures. A matrix of five microreactor component geometries, specifically based on the recent feasibility study on a Marvel microreactor liner, was developed and the Pacific Northwest National Laboratory team initiated one material/process combination, namely 316H using laser powder directed energy deposition (DED). Although the benchmark starts initially with simplistic cubical and cylindrical forms, it builds up to a mock-up of a non-proprietary design that can demonstrate a variety of features potentially useful for presenting knowledge to specific designers of microreactors and for the matter also for other reactor type designers. The initial cubical and cylindrical forms are initial steps to obtain surface features and dimensional responses to the identified process parameters to be used in the non-proprietary design mockup.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Improvement of SCALE-XSPROC Multigroup Cross Section Processing Based on the CENTRM Pointwise Slowing Down Calculation

The SCALE-XSProc multigroup (MG) cross section processing procedure based on the CENTRM pointwise slowing down calculation is the primary procedure to process problem-dependent self-shielded MG cross sections and scattering matrices for neutron transport calculations.This procedure supports various cell-based geometries including slab, 1-D cylindrical, 1-D spherical and 2-D rectangular configurations and doubly heterogeneous particulate fuels. Recently, this procedure has been significantly improved to be applied to any advanced reactor analysis covering thermal and fast reactor systems, and to be comparable to continuous energy (CE) Monte Carlo calculations. Some reactivity bias and reaction rate differences have been observed compared with CE Monte Carlo calculations, and several areas for improvement have been identified in the SCALE-XSProc MG cross section processing: (1) resonance self-shielding calculations within the unresolved resonance range, (2) 10 eV thermal cut-off energy for the free gas model, (3) on-the-fly adjustments to the thermal scattering matrix, (4) normalization of the pointwise neutron flux, and (5) fine MG energy structure. This procedure ensures very accurate MG cross section processing for high-fidelity deterministic reactor physics analysis for various advanced reactor systems.

Kim, Kang Seog↗
DOE OSTI2026

Delayed Neutron Precursor Group Parameter and Spectra Generation from Fast Fission of 235U in SCALE

Delayed neutron precursor (DNP) group data are important for modeling reactor dynamics. Although the data for individual DNPs have been developed over time, the DNP group data present in the Evaluated Nuclear Data Files (ENDF) have not been updated in the past 20 years. In this work, we use SCALE to recreate the Godiva experiment that was used to generate the original DNP group structure for fast fission of 235U. However, each DNP is modeled using up-to-date data, and the results are then converted into a newly updated group structure. This conversion uses an iterative linear least squares solver to minimize chi-squared. The approaches used in this work also enable energy spectrum generation and uncertainty tracking. The method used in this paper for fast 235U fission DNP group structure updating can be applied to different energies and fissile nuclides. Demonstration of the uncertainty tracking in reactor kinetics and dynamics simulations is shown using point reactor kinetics simulations. Results show that there are data discrepancies between the International Atomic Energy Agency database and data used in ORIGEN, which are currently being fixed. Results also show that the proposed method for group spectra generation performs well.

Seifert, Luke [University of Illinois]↗
DOE OSTI2020

The Novel Hybrid Ab Initio Model of High-Performance Structural Alloys Design for Fossil Energy Power Plants

The current project developed a novel HT-CALPHAD/DFT approach, which can quickly design new high-performance structural alloys for the application of FE power plants. The PI will mainly take charge of high-throughput DFT simulations and computational thermodynamics of the selected multicomponent alloy systems for the FE power plant applications. At the end of the project, a novel hybrid model based on high throughput CALPHAD/DFT simulations and computational thermodynamics will be developed to provide guidance on how to identify multi-component new high-performance structural alloys with much less computational effort needed. It will address the extensive computation time needed for DFT on the new alloys design. In addition, it will also address the well-known headache of DFT, i.e. how to make the accurate prediction of the high-temperature equilibria. The novel hybrid model the PI proposed will not only be applied to the design of high-performance structural alloys in FE power plants but in many different applications, such as nuclear reactors. This hybrid modeling approach includes four sections: 1) HT-CALPHAD modeling of Al-Co-Cr-Ni-Fe system with FCC and BCC phase. In this section, 3561 non-equiatomic compositions were randomly generated in order to investigate the phase stability of single FCC and BCC phases. Meanwhile, we proposed a data screening procedure to screen out the good candidates within these compositions, considering the temperature range, average density, and melting temperature, etc. 2) Investigation of FCC-Cr lattice stability in Fe-Cr system. We systematically assessed the reliability of FCC-Cr lattice stability derived by DFT and CALPHAD approaches. Meanwhile, the Fe-Cr binary system was chosen as a case study to verify the Cr lattice stability obtained by both approaches. 3) High-throughput DFT modeling on elastic properties of Al-Co-Cr-Ni-Fe systems. We predicted and established the FCC quinary elastic constant database of the Al-Co-Cr-Fe-Ni systems at 0K by using special quasi-random structure (SQS) approach. The predictions will start with pure elements of Al-Co-Cr-Fe-Ni system and will be continued with binaries, ternaries, quaternaries, and finally the quinary compositions. 3) Modeling of temperature-dependent elastic properties in Al-Co-Cr-Ni-Fe systems. In this part, we predict the thermal expansion coefficient and elastic stiffness coefficient as a function of temperature by applying quasiharmonic approximation. With this approach, the elastic properties of HEAs at elevate temperature can be estimated.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Irradiation damage concurrent challenges with RAFM and ODS steels for fusion reactor first-wall/blanket: a review

Reduced activation ferritic martensitic (RAFM) and oxide dispersion strengthened (ODS) steels are the most promising candidates for fusion first-wall/blanket (FW/B) structures. The performance of these steels will deteriorate during service due to neutron damage and transmutation-induced gases, such as helium/hydrogen, at elevated operating temperatures. Here, after highlighting the operating conditions of fusion reactor concepts and a brief overview, the main irradiation-induced degradation challenges associated with RAFM/ODS steels are discussed. Their long-term degradation scenarios such as (a) low-temperature hardening embrittlement (LTHE)—including dose-temperature dependent yield stress, tensile elongations, necking ductility, test temperature effect on hardening, Charpy impact ductile-to-brittle transition temperature and fracture toughness, (b) intermediate temperature cavity swelling, (c) the effect of helium on LTHE and cavity swelling, (d) irradiation creep and (e) tritium management issues are reviewed. The potential causes of LTHE are discussed, which highlights the need for advanced characterisation techniques. The mechanical properties, including the tensile/Charpy impact of RAFM and ODS steels, are compared to show that the current generation of ODS steels also suffers from LTHE, and shows irradiation hardening up to high temperatures of ~400 °C–500 °C. To minimise this, future ODS steel development for FW/B-specific application should target materials with a lower Cr concentration (to minimise α'), and minimise other elements that could form embrittling phases under irradiation. RAFM steel-designing activities targeting improvements in creep and LTHE are reviewed. The need to better understand the synergistic effects of helium on the thermo-mechanical properties in the entire temperature range of FW/B is highlighted. Because fusion operating conditions will be complex, including stresses due to the magnetic field, primary loads like coolant pressure, secondary loads from thermal gradients, and due to spatial variation in damage levels and gas production rates, an experimentally validated multiscale modelling approach is suggested as a pathway to future reactor component designing such as for the fusion neutron science facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Steady state radiolysis–polyhalide accumulation products [Poster]

The study of steady-state radiolysis of polyhalides is crucial as it simulates the prolonged radiation exposure that materials (e.g., alloys, molten salts) experience in reactor environments. This research provides valuable insights into the long-term effects on material properties, chemical stability, and structural integrity. It is closely linked with fundamental radiation chemistry, which aids in predicting the chemical behavior of accumulation products. Understanding the initial speciation, yield, and chemical evolution of radiolysis products is essential for managing material degradation, controlling corrosion, and ensuring reactor safety.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

In-situ microstructure observation of oxidized SiC layer in surrogate TRISO fuel particles under krypton ion irradiation

In accidental scenarios of high temperature gas-cooled reactors, both oxidation of and irradiation to the SiC layer in tri-structural-isotropic (TRISO) fuel particles can change the microstructure and integrity of the fuel elements. Here, in the present study, microstructure and defect evolution in the oxidized SiC layer of surrogate TRISO fuel particles under 1.2 MeV krypton ion irradiation was observed by in-situ transmission electron microscopy. The SiC layers oxidized in water vapor at 1200 °C were irradiated azt room temperature and 800 °C and at damage levels of 0.28–11.2 dpa, respectively. SiC and SiO 2 were found to still be in their crystal structures at the damage level of 11.2 dpa at 800 °C, while SiC was observed to have been amorphized at only 0.56 dpa irradiation at room temperature. The defect number density at 800 °C was an order of magnitude lower than that in the sample irradiated at room temperature. Also, crystalline SiO 2 had higher radiation resistance compared to SiC. A defect reaction rate theory was utilized to understand the fundamental defect evolution process and irradiation resistance difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Determination of preferential binder oxidation in HTGR matrix material subjected to high temperature steam

Graphitic matrix material encapsulates tristructural isotropic (TRISO) coated fuel particles and is a structural component for both pebble and cylindrical fuel compacts in high temperature gas reactor (HTGR) designs. In an off-normal event involving steam exposure, the matrix material is exposed to oxidants, leading to degradation of the fuel compact and subsequent exposure of the TRISO particle fuel to oxidizing species. This study presents microstructural characterization of matrix material after exposure to high temperature (1200°C), 48 kPa steam in which the evolved microstructure demonstrated nonuniform degradation. Subsequent Raman spectroscopy determined the nature of the remaining material post-exposure. Finally, the electron microscopy characterization suggests and Raman spectroscopic analysis confirms, under off-normal conditions, the carbonized phenolic resin binder is preferentially oxidized ahead of the graphite flake filler and is responsible for the nonuniform degradation and enhanced depth of attack.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ high-energy X-ray study of deformation mechanisms in additively manufactured 316L stainless steel

A key structural material planned to be used in the core of the Transformational Challenge Reactor is the additively manufactured 316L stainless steel (AM 316L SS). While the deformation of conventionally-manufactured 316 SS have been extensively studied, the deformation mechanism of AM 316L SS is less known. Here the room-temperature tensile behavior of AM 316L SS was studied in situ using high-energy X-ray diffraction and X-ray tomography. Diffraction yielded the lattice strains and the dislocation densi-ties of the AM 316L SS, which were compared to those of a conventionally processed 316H SS. It was found that while the conventional 316H SS had three distinct deformation stages, namely stage II ather-mal hardening, stage III dynamic recovery, and stage IV, the AM 316L experienced only the stages III and IV after an initial transitional period. The plastic instability stresses (PIS), i.e. the true ultimate tensile strength, were nearly the same in both materials. The AM 316L had very low dislocation barrier strength throughout the plastic deformation, which, in combination with the invariant PIS, explained its high dis-location storage capability and the attractive combination of strength and ductility. Tomography revealed morphological changes of the built-in pores in the AM 316L during deformation and fracture, and it was concluded that large pores close to the surface might have significant roles in the necking stage.

316 stainless steel↗
DOE OSTI2023

Exploration of LIBS as a novel and rapid elemental mapping technique of nuclear fuels in the form of surrogate TRISO particles

Laser-induced breakdown spectroscopy (LIBS) was employed to characterize coatings on surrogate fuel particles. Tri-structural isotropic (TRISO) particles are a proposed nuclear fuel alternative for high temperature reactors. These particles are constructed of a ZrO 2 kernel (as a surrogate to uranium), surrounded by an inner pyrolytic carbon layer and are surrounded by an outer carbide layer (ZrC, presented here) to act as a barrier to fission products generated during nuclear reactions. These particles are embedded within a graphite compact and housed within the reactor core. Simply put, due to their robust nature, performing elemental analysis of these particles poses a challenge. Presented here, LIBS is explored as a method for characterizing elemental constituents of these particles, with the focus being on rapid elemental mapping and depth profiling. Different from traditional elemental analysis techniques (e.g., inductively coupled plasma – based methods), LIBS is advantageous because it can directly analyze the sample surface and can detect light elements such as C and O, making it a viable technique for the analysis of small, multilayered particles as spatial elemental information is warranted in the production of these particles. In the work presented here, LIBS was successfully used for discerning small layers (30–50 μm), detecting the location of carbon and oxygen layers, providing fast 2-D mapping (<5 min per particle) and rapid depth profiling (10 s per particle).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗