Results for “aircraft engine performance” — Page 40

NASA NTRS2003

Neural Network and Regression Methods Demonstrated in the Design Optimization of a Subsonic Aircraft

The neural network and regression methods of NASA Glenn Research Center s COMETBOARDS design optimization testbed were used to generate approximate analysis and design models for a subsonic aircraft operating at Mach 0.85 cruise speed. The analytical model is defined by nine design variables: wing aspect ratio, engine thrust, wing area, sweep angle, chord-thickness ratio, turbine temperature, pressure ratio, bypass ratio, fan pressure; and eight response parameters: weight, landing velocity, takeoff and landing field lengths, approach thrust, overall efficiency, and compressor pressure and temperature. The variables were adjusted to optimally balance the engines to the airframe. The solution strategy included a sensitivity model and the soft analysis model. Researchers generated the sensitivity model by training the approximators to predict an optimum design. The trained neural network predicted all response variables, within 5-percent error. This was reduced to 1 percent by the regression method. The soft analysis model was developed to replace aircraft analysis as the reanalyzer in design optimization. Soft models have been generated for a neural network method, a regression method, and a hybrid method obtained by combining the approximators. The performance of the models is graphed for aircraft weight versus thrust as well as for wing area and turbine temperature. The regression method followed the analytical solution with little error. The neural network exhibited 5-percent maximum error over all parameters. Performance of the hybrid method was intermediate in comparison to the individual approximators. Error in the response variable is smaller than that shown in the figure because of a distortion scale factor. The overall performance of the approximators was considered to be satisfactory because aircraft analysis with NASA Langley Research Center s FLOPS (Flight Optimization System) code is a synthesis of diverse disciplines: weight estimation, aerodynamic analysis, engine cycle analysis, propulsion data interpolation, mission performance, airfield length for landing and takeoff, noise footprint, and others.

Hopkins, Dale A.↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS1982

Study of aerodynamic technology for single-cruise-engine VSTOL fighter/attack aircraft, phase 1

A conceptual design and analysis on a single engine VSTOL fighter/attack aircraft is completed. The aircraft combines a NASA/deHavilland ejector with vectored thrust and is capable of accomplishing the mission and point performance of type Specification 169, and a flight demonstrator could be built with an existing F101/DFE engine. The aerodynamic, aero/propulsive, and propulsive uncertainties are identified, and a wind tunnel program is proposed to address those uncertainties associated with wing borne flight.

Foley, W. H.↗

NASA NTRS1986

Advanced technology payoffs for future rotorcraft, commuter aircraft, cruise missile, and APU propulsion systems

In connection with the significant advances made regarding the performance of larger gas turbines, challenges arise concerning the improvement of small gas turbine engines in the 250 to 1000 horsepower range. In response to these challenges, the NASA/Army-sponsored Small Engine Component Technology (SECT) study was undertaken with the objective to identify the engine cycle, configuration, and component technology requirements for the substantial performance improvements desired in year-2000 small gas turbine engines. In the context of this objective, an American turbine engine company evaluated engines for four year-2000 applications, including a rotorcraft, a commuter aircraft, a supersonic cruise missile, and an auxiliary power unit (APU). Attention is given to reference missions, reference engines, reference aircraft, year-2000 technology projections, cycle studies, advanced engine selections, and a technology evaluation.

Turk, M. A.↗

NASA NTRS1993

Automation design and crew coordination

Advances in technology have greatly impacted the appearance of the modern aircraft cockpit. Where once one would see rows upon rows. The introduction of automation has greatly altered the demands on the pilots and the dynamics of aircrew task performance. While engineers and designers continue to implement the latest technological innovations in the cockpit - claiming higher reliability and decreased workload - a large percentage of aircraft accidents are still attributed to human error. Rather than being the main instigators of accidents, operators tend to be the inheritors of system defects created by poor design, incorrect installation, faulty maintenance and bad management decisions. This paper looks at some of the variables that need to be considered if we are to eliminate at least one of these inheritances - poor design. Specifically, this paper describes the first part of a comprehensive study aimed at identifying the effects of automation on crew coordination.

Segal, Leon D.↗

NASA NTRS1985

Icing flight research: Aerodynamic effects of ice and ice shape documentation with stereo photography

Aircraft icing flight research was performed in natural icing conditions. A data base consisting of icing cloud measurements, ice shapes, and aerodynamic measurements is being developed. During research icing encounters the icing cloud was continuously measured. After the encounter, the ice accretion shapes on the wing were documented with a stereo camera system. The increase in wing section drag was measured with a wake survey probe. The overall aircraft performance loss in terms of lift and drag coefficient changes was obtained by steady level speed/power measurements. Selective deicing of the airframe components was performed to determine their contributions to the total drag increase. Engine out capability in terms of power available was analyzed for the iced aircraft. It was shown that the stereo photography system can be used to document ice shapes in flight and that the wake survey probe can measure increases in wing section drag caused by ice. On one flight, the wing section drag coefficient (c sub d) increased approximately 120 percent over the uniced baseline at an aircraft angle of attack of 6 deg. On another flight, the aircraft darg coefficient (c sub d) increased by 75 percent over the uniced baseline at an aircraft lift coefficient (C sub d) of 0.5.

Mikkelsen, K. L.↗

NASA NTRS1985

Icing flight research - Aerodynamic effects of ice and ice shape documentation with stereo photography

Aircraft icing flight research was performed in natural icing conditions. A data base consisting of icing cloud measurements, ice shapes, and aerodynamic measurements is being developed. During research icing encounters the icing cloud was continuously measured. After the encounter, the ice accretion shapes on the wing were documented with a stereo camera system. The increase in wing section drag was measured with a wake survey probe. The overall aircraft performance loss in terms of lift and drag coefficient changes were obtained by steady level speed/power measurements. Selective deicing of the airframe components was performed to determine their contributions to the total drag increase. Engine out capability in terms of power available was analyzed for the iced aircraft. It was shown that the stereo photography system can be used to document ice shapes in flight and that the wake survey probe can measure increases in wing section drag caused by ice. On one flight, the wing section drag coefficient (c sub d) increased approximately 120 percent over the uniced baseline at an aircraft angle of attack of 6 deg. On another flight, the aircraft drag coefficient (c sub d) increased by 75 percent over the uniced baseline at an aircraft lift coefficient (c sub d) of 0.5.

Mikkelsen, K. L.↗

NASA NTRS1987

X-wing potential for Navy applications

The X-wing provides a VTOL aircraft which has a low disc loading hover capability, similar to a conventional helicopter, combined with a high subsonic cruise speed capability. As a result, it hovers with low fuel flow rates which make extended hover duration missions practical. Its low hover power requirements also permit hovering and low speed flight on only one engine in a high speed twin engine aircraft design. The NASA DARPA Sikorsky RSRA X-wing program developed flightworthy X-wing hardware. All design activity and the majority of its component fabrication is completed. A design study was performed on an X-wing concept demonstrator aircraft which is based on the RSRA X-wing components, combined with two MTE engines and a new fuselage.

Linden, Arthur W.↗

NASA NTRS1994

Comparison of X-31 flight, wind-tunnel, and water-tunnel yawing moment asymmetries at high angles of attack

The X-31 aircraft are being used in the enhanced fighter maneuverability (EFM) research program, which is jointly funded by the (U.S.) Advanced Research Projects Agency (ARPA) and Germany's Federal Ministry of Defense (FMOD). The flight test portion of the program, which involves two aircraft, is being conducted by an International Test Organization (ITO) comprising the National Aeronautics and Space Administration (NASA), the U.S. Navy, the U.S. Air Force, Rockwell International, and Deutsche Aerospace (DASA). The goals of the flight program are to demonstrate EFM technologies, investigate close-in-combat exchange ratios, develop design requirements, build a database for application to future fighter aircraft, and develop and validate low-cost prototype concepts. For longitudinal control the X-31 uses canards, symmetrical movement of the trailing-edge flaps, and pitch deflection of the thrust vectoring system. The trim, inertial coupling, and engine gyroscopic coupling compensation tasks are performed primarily by the trailing-edge flaps. For lateral-directional control the aircraft uses differential deflection of the trailing-edge flaps for roll coordination and a conventional rudder combined with the thrust vectoring system to provide yaw control. The rudder is only effective up to about 40 deg angle of attack (alpha), after which the thrust vectoring becomes the primary yaw control effector. Both the leading-edge flaps and the inlet lip are scheduled with the angle of attack to provide best performance.

Brent R Cobleigh↗

NASA NTRS1990

Development of the HIDEC inlet integration mode

The Highly Integrated Digital Electronic Control (HIDEC) development program conducted at NASA-Ames/Dryden will use an F-15 test aircraft for flight demonstration. An account is presently given of the HIDEC Inlet Integration mode's design concept, control law, and test aircraft implementation, with a view to its performance benefits. The enhancement of performance is a function of the use of Digital Electronic Engine Control corrected engine airflow computations to improve the scheduling of inlet ramp positions in real time; excess thrust can thereby be increased by 13 percent at Mach 2.3 and 40,000 ft. Aircraft supportability is also improved through the obviation of inlet controllers.

Chisholm, J. D.↗

NASA NTRS1997

High-Performance Parallel Analysis of Coupled Problems for Aircraft Propulsion

Applications are described of high-performance computing methods to the numerical simulation of complete jet engines. The methodology focuses on the partitioned analysis of the interaction of the gas flow with a flexible structure and with the fluid mesh motion driven by structural displacements. The latter is treated by a ALE technique that models the fluid mesh motion as that of a fictitious mechanical network laid along the edges of near-field elements. New partitioned analysis procedures to treat this coupled three-component problem were developed. These procedures involved delayed corrections and subcycling, and have been successfully tested on several massively parallel computers, including the iPSC-860, Paragon XP/S and the IBM SP2. The NASA-sponsored ENG10 program was used for the global steady state analysis of the whole engine. This program uses a regular FV-multiblock-grid discretization in conjunction with circumferential averaging to include effects of blade forces, loss, combustor heat addition, blockage, bleeds and convective mixing. A load-balancing preprocessor for parallel versions of ENG10 was developed as well as the capability for the first full 3D aeroelastic simulation of a multirow engine stage. This capability was tested on the IBM SP2 parallel supercomputer at NASA Ames.

Felippa, C. A.↗

NASA NTRS1974

A Flight Investigation of the STOL Characteristics of an Augmented Jet Flap STOL Research Aircraft

The flight test program objectives are: (1) To determine the in-flight aerodynamic, performance, and handling qualities of a jet STOL aircraft incorporating the augmented jet flap concept; (2) to compare the results obtained in flight with characteristics predicted from wind tunnel and simulator test results; (3) to contribute to the development of criteria for design and operation of jet STOL transport aircraft; and (4) to provide a jet STOL transport aircraft for STOL systems research and development. Results obtained during the first 8 months of proof-of-concept flight testing of the aircraft in STOL configurations are reported. Included are a brief description of the aircraft, fan-jet engines, and systems; a discussion of the aerodynamic, stability and control, and STOL performance; and pilot opinion of the handling qualities and operational characteristics.

Quigley, H. C.↗

NASA NTRS1999

The Typical General Aviation Aircraft

The reliability of General Aviation aircraft is unknown. In order to "assist the development of future GA reliability and safety requirements", a reliability study needs to be performed. Before any studies on General Aviation aircraft reliability begins, a definition of a typical aircraft that encompasses most of the general aviation characteristics needs to be defined. In this report, not only is the typical general aviation aircraft defined for the purpose of the follow-on reliability study, but it is also separated, or "sifted" into several different categories where individual analysis can be performed on the reasonably independent systems. In this study, the typical General Aviation aircraft is a four-place, single engine piston, all aluminum fixed-wing certified aircraft with a fixed tricycle landing gear and a cable operated flight control system. The system breakdown of a GA aircraft "sifts" the aircraft systems and components into five categories: Powerplant, Airframe, Aircraft Control Systems, Cockpit Instrumentation Systems, and the Electrical Systems. This breakdown was performed along the lines of a failure of the system. Any component that caused a system to fail was considered a part of that system.

Turnbull, Andrew↗

NASA NTRS2011

Inlet Flow Control and Prediction Technologies for Embedded Propulsion Systems

Fail-safe, hybrid, flow control (HFC) is a promising technology for meeting high-speed cruise efficiency, low-noise signature, and reduced fuel-burn goals for future, Hybrid-Wing-Body (HWB) aircraft with embedded engines. This report details the development of HFC technology that enables improved inlet performance in HWB vehicles with highly integrated inlets and embedded engines without adversely affecting vehicle performance. In addition, new test techniques for evaluating Boundary-Layer-Ingesting (BLI)-inlet flow-control technologies developed and demonstrated through this program are documented, including the ability to generate a BLI-like inlet-entrance flow in a direct-connect, wind-tunnel facility, as well as, the use of D-optimal, statistically designed experiments to optimize test efficiency and enable interpretation of results. Validated improvements in numerical analysis tools and methods accomplished through this program are also documented, including Reynolds-Averaged Navier-Stokes CFD simulations of steady-state flow physics for baseline, BLI-inlet diffuser flow, as well as, that created by flow-control devices. Finally, numerical methods were employed in a ground-breaking attempt to directly simulate dynamic distortion. The advances in inlet technologies and prediction tools will help to meet and exceed "N+2" project goals for future HWB aircraft.

McMillan, Michelle L.↗

NASA NTRS1976

Study of a very low cost air combat maneuvering trainer aircraft

A very low cost aircraft for performing Air Combat Maneuvering (ACM) training was studied using the BD-5J sport plane as a point of departure. The installation of a larger engine and increased fuel capacity were required to meet the performance and mission objectives. Reduced wing area increased the simulation of the ACM engagement, and a comparison with current tactical aircraft is presented. Other factors affecting the training transfer are considered analytically, but a flight evaluation is recommended to determine the concept utility.

Hill, G. C.↗