Search NASA⌕ Search

SEARCH · Search NASA

Results for “device stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A Semiconducting Two‐Dimensional Polymer as an Organic Electrochemical Transistor Active Layer

Abstract Organic electrochemical transistors (OECTs) are devices with broad potential in bioelectronic sensing, circuits, and neuromorphic hardware. Their unique properties arise from the use of organic mixed ionic/electronic conductors (OMIECs) as the active channel. Typical OMIECs are linear polymers, where defined and controlled microstructure/morphology, and reliable characterization of transport and charging can be elusive. Semiconducting two‐dimensional polymers (2DPs) present a new avenue in OMIEC materials development, enabling electronic transport along with precise control of well‐defined channels ideal for ion transport/intercalation. To this end, a recently reported 2DP, TIIP, is synthesized and patterned at 10 µm resolution as the channel of a transistor. The TIIP films demonstrate textured microstructure and show semiconducting properties with accessible oxidation states. Operating in an aqueous electrolyte, the 2DP‐OECT exhibits a device‐scale hole mobility of 0.05 cm 2 V –1 s –1 and a µ C * figure of merit of 1.75 F cm –1 V –1 s –1 . 2DP OMIECs thus offer new synthetic degrees of freedom to control OECT performance and may enable additional opportunities such as ion selectivity or improved stability through reduced morphological modulation during device operation.

2D-polymer↗
DOE OSTI2016

Laterally configured resistive switching device based on transition-metal nano-gap electrode on Gd oxide

We have developed a fabrication process for a laterally configured resistive switching device based on a Gd oxide. A nano-gap electrode connected by a Gd oxide with the ideal interfaces has been created by adapting the electro-migration method in a metal/GdO{sub x} bilayer system. Bipolar set and reset operations have been clearly observed in the Pt/GdO{sub x} system similarly in the vertical device based on GdO{sub x}. Interestingly, we were able to observe a clear bipolar switching also in a ferromagnetic CoFeB nano-gap electrode with better stability compared to the Pt/GdO{sub x} device. The superior performance of the CoFeB/GdO{sub x} device implies the importance of the spin on the resistive switching.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2019

Improved Efficiency and Stability of Pb/Sn Binary Perovskite Solar Cells Fabricated by Galvanic Displacement Reaction

In this work, a simple and generally applicable method of fabricating efficient and stable Pb-Sn binary perovskite solar cells (PVSCs) based on a galvanic displacement reaction (GDR) is demonstrated. Different from the commonly used conventional approaches to form perovskite precursor solutions by mixing metal halides and organic halides such as PbI 2 , SnI 2 , MAI, FAI, etc., together, the precursor solutions are formulated by reacting pure Pb-based perovskite precursor solutions with fine Sn metal powders. After the ratios between Pb and Sn are optimized, high PCEs of 15.85% and 18.21% can be achieved for MAPb 0.4 Sn 0.6 I 3 and (FAPb 0.6 Sn 0.4 I 3 ) 0.85 (MAPb 0.6 Sn 0.4 Br 3 ) 0.15 based PVSCs, which are the highest PCEs among all values reported to date for Pb-Sn binary PVSCs. Moreover, the GDR perovskite-based PVSCs exhibit significantly improved ambient and thermal stability with encapsulation, which can retain more than 90% of their initial PCEs after being stored in ambient (relative humidity (RH) ≈50%) for 1000 h or being thermal annealed at 80 °C for more than 120 h in ambient conditions. These results demonstrate the advantage of using GDR to prepare tunable bandgap binary perovskites for devices with greatly improved performance and stability.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Aspect ratio effects on neoclassical tearing modes from comparison between DIII-D and National Spherical Torus Experiment

Neoclassical tearing mode islands are sustained by helically perturbed bootstrap currents arising at finite beta from toroidal effects that trap a fraction of the particles in non-circulating orbits. DIII-D and NSTX are here operated with similar shape and cross-sectional area but almost a factor of two difference in inverse aspect ratio a/R. In these experiments, destabilized n=1 tearing modes were self-stabilized (reached the 'marginal point') by reducing neutral-beam power and thus beta. The measure of the marginal island gives information on the small-island stabilizing physics that in part (with seeding) governs onset. The marginal island width on NSTX is found to be about three times the ion banana width and agrees with that measured in DIII-D, except for DIII-D modes closer to the magnetic axis, which are about two times the ion banana width. There is a balance of the helically perturbed bootstrap term with small island effects with the sum of the classical and curvature terms in the modified Rutherford equation for tearing-mode stability at the experimental marginal point. Empirical evaluation of this sum indicates that while the stabilizing effect of the curvature term is negligible in DIII-D, it is important in NSTX. The mode temporal behavior from the start of neutral-beam injection reduction also suggests that NSTX operates closer to marginal classical tearing stability; this explains why there is little hysteresis in beta between mode onset, saturation, and self-stabilization (while DIII-D has large hysteresis in beta). NIMROD code module component calculations based on DIII-D and NSTX reconstructed experimental equilibria are used to diagnose and confirm the relative importance of the stabilizing curvature effect, an advantage for low aspect ratio; the relatively greater curvature effect makes for less susceptibility to NTM onset even if the classical tearing stability index is near marginal.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Enabling full-scale grain boundary mitigation in polycrystalline perovskite solids

There exists a considerable density of interaggregate grain boundaries (GBs) and intra-aggregate GBs in polycrystalline perovskites. Mitigation of intra-aggregate GBs is equally notable to that of interaggregate GBs as intra-aggregate GBs can also cause detrimental effects on the photovoltaic performances of perovskite solar cells (PSCs). Here, we demonstrate full-scale GB mitigation ranging from nanoscale intra-aggregate to submicron-scale interaggregate GBs, by modulating the crystallization kinetics using a judiciously designed brominated arylamine trimer. The optimized GB-mitigated perovskite films exhibit reduced nonradiative recombination, and their corresponding mesostructured PSCs show substantially enhanced device efficiency and long-term stability under illumination, humidity, or heat stress. The versatility of our strategy is also verified upon applying it to different categories of PSCs. Our discovery not only specifies a rarely addressed perspective concerning fundamental studies of perovskites at nanoscale but also opens a route to obtain high-quality solution-processed polycrystalline perovskites for high-performance optoelectronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Space Application Requirements for Organic Avionics

The NASA Marshall Space Flight Center is currently evaluating polymer based components for application in launch vehicle and propulsion system avionics systems. Organic polymers offer great advantages over inorganic corollaries. Unlike inorganics with crystalline structures defining their sensing characteristics, organic polymers can be engineered to provide varying degrees of sensitivity for various parameters including electro-optic response, second harmonic generation, and piezoelectric response. While great advantages in performance can be achieved with organic polymers, survivability in the operational environment is a key aspect for their practical application. The space environment in particular offers challenges that must be considered in the application of polymer based devices. These challenges include: long term thermal stability for long duration missions, extreme thermal cycling, space radiation tolerance, vacuum operation, low power operation, high operational reliability. Requirements for application of polymer based devices in space avionics systems will be presented and discussed in light of current polymer materials.

Watson, Michael D.↗
DOE OSTI2026

Review on Perovskite Solar Cells: From Single‐Junction Devices to Tandem Deployment in Space

Perovskite solar cells (PSCs) have emerged as a transformative photovoltaic technology, offering high power conversion efficiency (PCE) and the potential for cost-effective manufacturing. However, stability and large-scale manufacturing remain critical challenges that must be addressed for widespread adoption. This review provides a roadmap from single-junction perovskite solar cells to tandem deployment in space. First, material-level innovations are discussed, including mixed-cation and low-dimensional perovskites, transport materials, and additives that improve thermal and structural stability while enhancing efficiency. Then, we examine both established industrial standards and emerging scientific protocols aimed at stabilizing PSCs under operational conditions, including tandem cell integration strategies and encapsulation techniques to mitigate performance degradation. Manufacturing scalability is a focal point, where deposition methods and green solvents are explored to improve large-area film uniformity and reduce environmental impact. Additionally, the increasing viability of PSCs in extraterrestrial environments is assessed, with emphasis on their performance in space applications, radiation resistance, and flexible lamination methods for deployment in extreme conditions. Progress across materials innovation, device architectures, stability testing protocols, and both terrestrial and extraterrestrial applications collectively drives perovskite photovoltaics toward higher efficiency, stability, and cost-effectiveness.

flexible PSCs↗
DOE OSTI2015

Quantifying data retention of perpendicular spin-transfer-torque magnetic random access memory chips using an effective thermal stability factor method

The thermal stability of perpendicular Spin-Transfer-Torque Magnetic Random Access Memory (STT-MRAM) devices is investigated at chip level. Experimental data are analyzed in the framework of the Néel-Brown model including distributions of the thermal stability factor Δ. We show that in the low error rate regime important for applications, the effect of distributions of Δ can be described by a single quantity, the effective thermal stability factor Δ{sub eff}, which encompasses both the median and the standard deviation of the distributions. Data retention of memory chips can be assessed accurately by measuring Δ{sub eff} as a function of device diameter and temperature. We apply this method to show that 54 nm devices based on our perpendicular STT-MRAM design meet our 10 year data retention target up to 120 °C.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

SU-E-J-258: Inter- and Intra-Fraction Setup Stability and Couch Change Tolerance for Image Guided Radiation Therapy

Purpose: Immobilization devices combine rigid patient fixation as well as comfort and play a key role providing the stability required for accurate radiation delivery. In the setup step, couch re-positioning needed to align the patient is derived via registration of acquired versus reference image. For subsequent fractions, replicating the initial setup should yield identical alignment errors when compared to the reference. This is not always the case and further couch re-positioning can be needed. An important quality assurance measure is to set couch tolerances beyond which additional investigations are needed. The purpose of this work was to study the inter-fraction couch changes needed to re-align the patient and the intra-fraction stability of the alignment as a guide to establish the couch tolerances. Methods: Data from twelve patients treated on the Accuray CyberKnife (CK) system for fractionated intracranial radiotherapy and immobilized with Aquaplast RT, U-frame, F-Head-Support (Qfix, PA, USA) was used. Each fraction involved image acquisitions and registration with the reference to re-align the patient. The absolute couch position corresponding to the approved setup alignment was recorded per fraction. Intra-fraction set-up corrections were recorded throughout the treatment. Results: The average approved setup alignment was 0.03±0.28mm, 0.15±0.22mm, 0.06±0.31mm in the L/R, A/P, S/I directions respectively and 0.00±0.35degrees, 0.03±0.32degrees, 0.08±0.45degrees for roll, pitch and yaw respectively. The inter-fraction reproducibility of the couch position was 6.65mm, 10.55mm, and 4.77mm in the L/R, A/P and S/I directions respectively and 0.82degrees, 0.71degrees for roll and pitch respectively. Intra-fraction monitoring showed small average errors of 0.21±0.21mm, 0.00±0.08mm, 0.23±0.22mm in the L/R, A/P, S/I directions respectively and 0.03±0.12degrees, 0.04±0.25degrees, and 0.13±0.15degrees in the roll, pitch and yaw respectively. Conclusion: The inter-fraction reproducibility should serve as a guide to couch tolerances, specific to a site and immobilization. More patients need to be included to make general conclusions.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Comparison of Metal Adhesion Layers for Au Films in Thermoplasmonic Applications

If thermoplasmonic applications such as heat-assisted magnetic recording are to be commercially viable, it is necessary to optimize both thermal stability and plasmonic performance of the devices involved. In this work, a variety of different adhesion layers were investigated for their ability to reduce dewetting of sputtered 50 nm Au films on SiO 2 substrates. Traditional adhesion layer metals Ti and Cr were compared with alternative materials of Al, Ta, and W. Film dewetting was shown to increase when the adhesion material diffuses through the Au layer. An adhesion layer thickness of 0.5 nm resulted in superior thermomechanical stability for all adhesion metals, with an enhancement factor of up to 200X over 5 nm thick analogues. The metals were ranked by their effectiveness in inhibiting dewetting, starting with the most effective, in the order Ta > Ti > W > Cr > AI. Finally, the Au surface-plasmon polariton response was compared for each adhesion layer, and it was found that 0.5 nm adhesion layers produced the best response, with W being the optimal adhesion layer material for plasmonic performance.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Rotational stability of a long field-reversed configuration

Rotationally driven modes of long systems with dominantly axial magnetic field are considered. We apply the incompressible model and order axial wavenumber small. A recently developed gyro-viscous model is incorporated. A one-dimensional equilibrium is assumed, but radial profiles are arbitrary. The dominant toroidal (azimuthal) mode numbers ℓ=1 and ℓ=2 modes are examined for a variety of non-reversed (B) and reversed profiles. Previous results for both systems with rigid rotor equilibria are reproduced. New results are obtained by incorporation of finite axial wavenumber and by relaxing the assumption of rigid electron and ion rotation. It is shown that the frequently troublesome ℓ=2 field reversed configuration (FRC) mode is not strongly affected by ion kinetic effects (in contrast to non-reversed cases) and is likely stabilized experimentally only by finite length effects. It is also shown that the ℓ=1 wobble mode has a complicated behavior and is affected by a variety of configuration and profile effects. The rotationally driven ℓ=1 wobble is completely stabilized by strong rotational shear, which is anticipated to be active in high performance FRC experiments. Thus, observed wobble modes in these systems are likely not driven by rotation alone.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Spin-transfer-torque efficiency enhanced by edge-damage of perpendicular magnetic random access memories

We numerically investigate the effect of magnetic and electrical damages at the edge of a perpendicular magnetic random access memory (MRAM) cell on the spin-transfer-torque (STT) efficiency that is defined by the ratio of thermal stability factor to switching current. We find that the switching mode of an edge-damaged cell is different from that of an undamaged cell, which results in a sizable reduction in the switching current. Together with a marginal reduction of the thermal stability factor of an edge-damaged cell, this feature makes the STT efficiency large. Our results suggest that a precise edge control is viable for the optimization of STT-MRAM.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Numerical study on the stabilization of neoclassical tearing modes by electron cyclotron current drive

It is well known that electron cyclotron current drive (ECCD) around the o-point of magnetic island along the plasma current direction can stabilize neoclassical tearing modes (NTMs) in tokamak devices. The effects of the radial misalignment between the island and the driven current, the phase misalignment, and the on-duty ratio for modulated current drive on NTM stabilization are studied numerically in this paper. A small radial misalignment is found to significantly decrease the stabilizing effect. When a sufficiently large phase misalignment occurs for the modulated ECCD, the stabilization effect is also reduced a lot. The optimal on-duty ratio of modulated ECCD to stabilize NTMs is found to be in the range of 60%–70%. A larger on-duty ratio than 50% could also mitigate the effect of phase misalignment if it is not too large. There is no benefit from modulation if the phase misalignment is larger than a threshold.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1992

Adaptive attitude control and momentum management for large-angle spacecraft maneuvers

The fully coupled equations of motion are systematically linearized around an equilibrium point of a gravity gradient stabilized spacecraft, controlled by momentum exchange devices. These equations are then used for attitude control system design of an early Space Station Freedom flight configuration, demonstrating the errors caused by the improper approximation of the spacecraft dynamics. A full state feedback controller, incorporating gain-scheduled adaptation of the attitude gains, is developed for use during spacecraft on-orbit assembly or operations characterized by significant mass properties variations. The feasibility of the gain adaptation is demonstrated via a Space Station Freedom assembly sequence case study. The attitude controller stability robustness and transient performance during gain adaptation appear satisfactory.

Parlos, Alexander G.↗
DOE OSTI2018

A Novel Interfacing Technique for Distributed Hybrid Simulations Combining EMT and Transient Stability Models

With steady increase of power electronic devices and nonlinear dynamic loads in large scale AC/DC systems, the traditional hybrid simulation method, which incorporates these components into a single EMT subsystem and hence causes great difficulty for network partitioning and significant deterioration in simulation efficiency. To resolve these issues, a novel distributed hybrid simulation method is proposed in this paper. The key to realize this method is a distinct interfacing technique, which includes: i) a new approach based on the two-level Schur complement to update the interfaces by taking full consideration of the couplings between different EMT subsystems; and ii) a combined interaction protocol to further improve the efficiency while guaranteeing the simulation accuracy. The advantages of the proposed method in terms of both efficiency and accuracy have been verified by using it for the simulation study of an AC/DC hybrid system including a two-terminal VSC-HVDC and nonlinear dynamic loads.

Distributed hybrid simulation↗
DOE OSTI2022

Development of Integrated Education, Training and Research Program with Interdisciplinary Applications

Plasma models have been formulated including realistic spatial profiles of both flow and radio frequency induced ponderomotive force. With these inclusions the picture of stability of various plasma and fluid instabilities, as expected, changed drastically with ground-breaking consequences. The inhomogeneous parallel flow and the radio frequency waves can actually shown to stabilize turbulence. This is different from the prevalent notion that both parallel flow shear and radio frequency waves are responsible for the excitation (destabilization) of plasma turbulence. This has several ground-breaking consequences:- (1) the stabilization by parallel flow clearly goes against the conventional notion of the origin of ionospheric oscillation which invokes parallel flow destabilization as the origin, (2) the stabilization by parallel flow opens us a new avenue for improved mode formation in fusion devices - which mostly rely on the perpendicular flow shear stabilization for improved mode formation but the perpendicular flow is damped in a tokamak - so the improved mode formed by the parallel flow can sustain longer and has more prospect for ignition, (3) the complete stabilization of the ITG mode (and consequent suppression of transport) not only explain many unknown phenomena in the space physics but it also raises a prospect for transport barrier formation by the RF waves but not by the RF induced flow (as most works suggest) which is never observed in a tokamak of that magnitude to create a barrier. These are indeed ground-breaking consequences.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Development of Integrated Education, Training and Research Program with Interdisciplinary Applications II

Plasma models have been formulated including realistic spatial profiles of both flow and radio frequency induced ponderomotive force. With these inclusions the picture of stability of various plasma and fluid instabilities, as expected, changed drastically with ground-breaking consequences. The inhomogeneous parallel flow and the radio frequency waves can actually shown to stabilize turbulence. This is different from the prevalent notion that both parallel flow shear and radio frequency waves are responsible for the excitation (destabilization) of plasma turbulence. This has several ground-breaking consequences:- (1) the stabilization by parallel flow clearly goes against the conventional notion of the origin of ionospheric oscillation which invokes parallel flow destabilization as the origin, (2) the stabilization by parallel flow opens us a new avenue for improved mode formation in fusion devices - which mostly rely on the perpendicular flow shear stabilization for improved mode formation but the perpendicular flow is damped in a tokamak - so the improved mode formed by the parallel flow can sustain longer and has more prospect for ignition, (3) the complete stabilization of the ITG mode (and consequent suppression of transport) not only explain many unknown phenomena in the space physics but it also raises a prospect for transport barrier formation by the RF waves but not by the RF induced flow (as most works suggest) which is never observed in a tokamak of that magnitude to create a barrier. These are indeed ground-breaking consequences.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

On a fully-implicit VMS-stabilized FE formulation for low Mach number compressible resistive MHD with application to MCF

This study presents the development and evaluation of a fully-implicit variational multiscale (VMS) stabilized unstructured finite element (FE) formulation for compressible magnetohydrodynamics (MHD) model, at low Mach number regime. The model describes the dynamics of a compressible conducting fluid in the low Mach number limit in the presence of electromagnetic fields and can be used to study aspects of astrophysical phenomena, important science and technology applications, and basic plasma physics phenomena. The specific applications that motivate this study are macroscopic simulations of the longer time-scale stability and disruptions of magnetic confinement fusion (MCF) devices, specifically the ITER tokamak. The discussion considers the development of the VMS FE representation, the structure of the stabilizing terms that deal with significant convective flows, the stabilization of the nearly incompressible response of the fluid flow, and the stabilization of the constraint that enforces the solenoidal involution on the magnetic field. The nonlinear discretized system is solved with scalable preconditioned Newton–Krylov iterative methods, which employs a multiphysics block preconditioning method based on approximate block factorizations and Schur complements. The study presents an evaluation of the VMS method on a 2D cartesian tearing mode instability, and illustrates the scalability of the solvers on MCF relevant problems. A set of results are also presented for longer time-scale stability and disruptions for the ITER tokamak. These include a vertical displacement event (VDE), and a (1,1) internal kink mode. Here, the formulation is demonstrated to be scalable and also reasonably robust with respect to the Lundquist number scaling.

42 ENGINEERING↗