Search NASA⌕ Search

SEARCH · Search NASA

Results for “error estimate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Airplane wing vibrations due to atmospheric turbulence

The magnitude of error introduced due to wing vibration when measuring atmospheric turbulence with a wind probe mounted at the wing tip was studied. It was also determined whether accelerometers mounted on the wing tip are needed to correct this error. A spectrum analysis approach is used to determine the error. Estimates of the B-57 wing characteristics are used to simulate the airplane wing, and von Karman's cross spectrum function is used to simulate atmospheric turbulence. It was found that wing vibration introduces large error in measured spectra of turbulence in the frequency's range close to the natural frequencies of the wing.

Pastel, R. L.↗

Use of GRACE Terrestrial Water Storage Retrievals to Evaluate Model Estimates by the Australian Water Resources Assessment System

Terrestrial water storage (TWS) estimates retrievals from the Gravity Recovery and Climate Experiment (GRACE) satellite mission were compared to TWS modeled by the Australian Water Resources Assessment (AWRA) system. The aim was to test whether differences could be attributed and used to identify model deficiencies. Data for 2003 2010 were decomposed into the seasonal cycle, linear trends and the remaining de-trended anomalies before comparing. AWRA tended to have smaller seasonal amplitude than GRACE. GRACE showed a strong (greater than 15 millimeter per year) drying trend in northwest Australia that was associated with a preceding period of unusually wet conditions, whereas weaker drying trends in the southern Murray Basin and southwest Western Australia were associated with relatively dry conditions. AWRA estimated trends were less negative for these regions, while a more positive trend was estimated for areas affected by cyclone Charlotte in 2009. For 2003-2009, a decrease of 7-8 millimeter per year (50-60 cubic kilometers per year) was estimated from GRACE, enough to explain 6-7% of the contemporary rate of global sea level rise. This trend was not reproduced by the model. Agreement between model and data suggested that the GRACE retrieval error estimates are biased high. A scaling coefficient applied to GRACE TWS to reduce the effect of signal leakage appeared to degrade quantitative agreement for some regions. Model aspects identified for improvement included a need for better estimation of rainfall in northwest Australia, and more sophisticated treatment of diffuse groundwater discharge processes and surface-groundwater connectivity for some regions.

van Dijk, A. I. J. M.↗

Battery state of health monitoring by estimation of the number of cyclable Li-ions

Herein this paper introduces a method to monitor battery state of health (SOH) by estimating the number of cyclable Li-ions, a health-relevant electrochemical variable. SOH monitoring is critical to battery management in balancing the trade-off between maximizing system performance and minimizing battery degradation. The decrease of cyclable Li-ions indicates the effect on the SOH of degradation mechanisms that consume cyclable Li-ions. The unavailability of the number of cyclable Li-ions through non-invasive measurements makes its estimation necessary for in-situ SOH monitoring. In this paper, the extended Kalman filter (EKF) is used to estimate the number of cyclable Li-ions as an unknown battery parameter. The single particle model (SPM), a simplified battery electrochemical model, is used as the model in the EKF to achieve a computational complexity suitable for on-line estimation. Simulations are performed under typical electric vehicle current trajectories using an example parameter set for a hybrid-electric-vehicle battery. In the simulations, the battery is represented by the Doyle–Fuller–Newman (DFN) model, an electrochemical model with higher fidelity than the SPM. To comply with the practice, instead of using the same parameters as the DFN model in the SPM, parameterization of the SPM is performed before estimation of the number of cyclable Li-ions. The simulations show high estimation accuracy of the number of cyclable Li-ions using the EKF, even with the structural and parametric differences between the DFN model and the SPM, under both the ideal conditions and various non-ideal conditions (i.e., SOC estimation error, additional modeling error, and measurement noise).

25 ENERGY STORAGE↗

A study of shock initiation experiments for the explosive PBX 9502 using three reactive burn models

Shock to detonation transition (SDT) experiments are essential in calibrating and validating reactive burn models for explosives. This work investigates the large collection of SDT test data for the explosive PBX 9502 at ambient temperature that was presented by Gustavsen, Sheffield, and Alcon [Journal of Applied Physics, 99, 114907 (2006)]. We first analyze the experimental data and compare two different methods of determining the shock transition time/distance (namely, the bilinear method and the single-curve method). This reveals some of the uncertainty in estimating shock transition points, which contributes to scatter in Pop-plot data. Next, we compare the WSD, AWSD, and SURFplus reactive burn models for a collection of approximately 20 experimental shots using the FLAG hydrocode. Error estimates are used to quantify how well each reactive burn model (and their respective parameter calibrations) performs at predicting the SDT process for a range of loading conditions. Additionally, the importance of mesh resolution and numerical dissipation in SDT simulations will be assessed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Large-momentum effective theory’s asymptotic extrapolation vs the inverse problem

Large-momentum effective theory is a physics-guided systematic expansion to calculate light-cone parton distributions, including collinear (PDFs) and transverse-momentum-dependent ones, at any fixed momentum fraction 𝑥 within a range of [𝑥 min , 𝑥 max ]. It theoretically solves the ill-posed inverse problem that afflicts other theoretical approaches to collinear PDFs, such as short-distance factorizations. Recently, Dutrieux et al. raised practical concerns about whether current or even future lattice data will have sufficient precision in the subasymptotic correlation region to support an error-controlled extrapolation—and if not, whether it becomes an inverse problem where the relevant uncertainties cannot be properly quantified. While we agree that not all current lattice data have the desired precision to qualify for an asymptotic extrapolation, some calculations do, and more are expected in the future. We comment on the analysis and results in Dutrieux et al. and argue that a physics-based systematic extrapolation still provides the most reliable error estimates, even when the data quality is not ideal. In contrast, reframing the long-distance asymptotic extrapolation as a data-driven-only inverse problem with ad hoc mathematical conditioning could lead to unnecessarily conservative errors.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

THE LARGE-SCALE THREE-POINT CORRELATION FUNCTION OF SLOAN DIGITAL SKY SURVEY LUMINOUS RED GALAXIES

We present new measurements of the redshift-space three-point correlation function (3PCF) of Luminous Red Galaxies (LRGs) from the Sloan Digital Sky Survey (SDSS). Using the largest data set to date, the Data Release 7 LRGs, and an improved binning scheme compared to previous measurements, we measure the LRG 3PCF on large scales up to {approx}90 h{sup -1} Mpc, from the mildly nonlinear to quasi-linear regimes. Comparing the LRG correlations to the dark matter two- and three-point correlation functions, obtained from N-body simulations we infer linear and nonlinear bias parameters. As expected, LRGs are highly biased tracers of large-scale structure, with a linear bias b{sub 1} {approx} 2; the LRGs also have a large positive nonlinear bias parameter, in agreement with predictions of galaxy population models. The use of the 3PCF to estimate biasing helps to also make estimates of the cosmological parameter {sigma}{sub 8}, as well as to infer best-fit parameters of the halo occupation distribution parameters for LRGs. We also use a large suite of public mock catalogs to characterize the error covariance matrix for the 3PCF and compare the variance among simulation results with jackknife error estimates.

79 ASTRONOMY AND ASTROPHYSICS↗

Axial, scalar, and tensor charges of the nucleon from 2+1+1-flavor Lattice QCD

We present results for the isovector axial, scalar, and tensor charges 𝑔$^{𝑢−𝑑}_{𝐴}$, 𝑔$^{𝑢−𝑑}_{𝑆}$, and 𝑔$^{𝑢−𝑑}_{𝑇}$ of the nucleon needed to probe the Standard Model and novel physics. The axial charge is a fundamental parameter describing the weak interactions of nucleons. The scalar and tensor charges probe novel interactions at the TeV scale in neutron and nuclear 𝛽-decays, and the flavor-diagonal tensor charges 𝑔$^{𝑢}_{𝑇}$, 𝑔$^{𝑑}_{𝑇}$, and 𝑔$^{𝑠}_{𝑇}$ are needed to quantify the contribution of the quark electric dipole moment (EDM) to the neutron EDM. The lattice-QCD calculations were done using nine ensembles of gauge configurations generated by the MILC Collaboration using the highly improved staggered quarks action with 2+1+1 dynamical flavors. These ensembles span three lattice spacings 𝑎 ≈0.06,0.09, and 0.12 fm and light-quark masses corresponding to the pion masses 𝑀 𝜋 ≈ 135,225, and 315 MeV. High-statistics estimates on five ensembles using the all-mode-averaging method allow us to quantify all systematic uncertainties and perform a simultaneous extrapolation in the lattice spacing, lattice volume, and light-quark masses for the connected contributions. Our final estimates, in the $\overline{MS}$ scheme at 2 GeV, of the isovector charges are 𝑔$^{𝑢−𝑑}_{𝐴}$ = 1.195⁢(33)⁢(20), 𝑔$^{𝑢−𝑑}_{𝑆}$ = 0.97⁢(12)⁢(6), and 𝑔$^{𝑢−𝑑}_{𝑇}$ = 0.987⁢(51)⁢(20). The first error includes statistical and all systematic uncertainties except that due to the extrapolation Ansatz, which is given by the second error estimate. Combining our estimate for 𝑔$^{𝑢−𝑑}_{𝑆}$ with the difference of light quarks masses (𝑚 𝑑 − 𝑚 𝑢 ) QCD = 2.67⁢(35) MeV given by the Flavor Lattice Average Group, we obtain (𝑀 𝑁 − 𝑀 𝑃 ) QCD = 2.59⁢(49) MeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

ICESat-2 Pointing Calibration and Geolocation Performance

ICESat-2 science requirements are dependent on the accurate real-time pointing control (i.e. geolocation control) and post-processed geolocation knowledge of the laser altimeter surface returns. Pre-launch pointing alignment errors and post-launch pointing alignment variation result in large geolocation errors that must be calibrated on orbit. In addition, the changing sun-orbit geometry causes thermal-mechanical forced laser frame alignment variations at the orbit period and trends from days, weeks and months. Early mission analysis computed precise post-launch laser beam alignment calibration. The alignment calibration was uploaded to the spacecraft and enabled the pointing control performance to achieve 4.4 ± 6.0 m, a significant improvement over the 45 m (1 σ) mission requirement. Laser frame alignment calibrations are used to reduce the alignment bias and time variation, as well as the orbital variation contributions to geolocation knowledge error from 6 m to 1.7 m (1 σ). Relative beam alignment of the six beams is calibrated and shown to contribute between 0.5 ± 0.1 m and 2.4 ± 0.2 m of remaining geolocation knowledge error. Independent geolocation assessment based on comparison to high-resolution digital elevation models agrees well with the calibration geolocation error estimates. The analysis demonstrates the ICESat-2 mission is performing far better than its geolocation knowledge requirement of 6.5 m (1 σ) after the laser frame alignment bias variation and orbital variation calibrations have been applied. Remaining geolocation error is beam dependent and ranges from 2.5 m for beam 6 to 4.4 m for beam 2 (mean + 1 σ).

S. B. Luthcke↗

ICESat-2 Pointing Calibration and Geolocation Performance

ICESat-2 science requirements are dependent on the accurate real-time pointing control (i.e., geolocation control) and postprocessed geolocation knowledge of the laser altimeter surface returns. Prelaunch pointing alignment errors and postlaunch pointing alignment variation result in large geolocation errors that must be calibrated on orbit. In addition, the changing sun-orbit geometry causes thermal-mechanical forced laser frame alignment variations at the orbit period and trends from days, weeks, and months. Early mission analysis computed precise postlaunch laser beam alignment calibration. The alignment calibration was uploaded to the spacecraft and enabled the pointing control performance to achieve 4.4 ± 6.0 m, a significant improvement over the 45 m (1 σ) mission requirement. Laser frame alignment calibrations are used to reduce the alignment bias and time variation, as well as the orbital variation contributions to geolocation knowledge error from 6 to 1.7 m (1 σ). Relative beam alignment of the six beams is calibrated and shown to contribute between 0.5 ± 0.1 m and 2.4 ± 0.2 m of remaining geolocation knowledge error. Independent geolocation assessment based on comparison to high-resolution digital elevation models agrees well with the calibration geolocation error estimates. The analysis demonstrates the ICESat-2 mission is performing far better than its geolocation knowledge requirement of 6.5 m (1 σ) after the laser frame alignment bias variation and orbital variation calibrations have been applied. Remaining geolocation error is beam dependent and ranges from 2.5 m for beam 6 to 4.4 m for beam 2 (mean + 1 σ).

S B Luthcke↗

Construction of the Nordsieck second derivative methods with RK stability for stiff ODEs

In this paper, we study the construction and implementation of special Nordsieck second derivative general linear methods of order p and stage order q=p in which the number of input and output values is r=p rather than r=p+1. We will construct A- and L-stable methods of orders three and four in this form with Runge–Kutta stability properties. The efficiency of the constructed methods and reliability of the proposed error estimates are shown by implementing of the methods in a variable stepsize environment on some well-known stiff problems.

97 MATHEMATICS AND COMPUTING↗

Dynamic State Estimation for Multi-Machine Power System by Unscented Kalman Filter With Enhanced Numerical Stability

In this paper, in order to enhance the numerical stability of the unscented Kalman filter (UKF) used for power system dynamic state estimation, a new UKF with guaranteed positive semidifinite estimation error covariance (UKFGPS) is proposed and compared with five existing approaches, including UKFschol, UKF-kappa, UKFmodified, UKF-Delta Q, and the squareroot UKF (SRUKF). These methods and the extended Kalman filter (EKF) are tested by performing dynamic state estimation on WSCC 3-machine 9-bus system and NPCC 48-machine 140-bus system. For WSCC system, all methods obtain good estimates. However, for NPCC system, both EKF and the classic UKF fail. It is found that UKFschol, UKF-kappa, and UKF-Delta Q do not work well in some estimations while UKFGPS works well in most cases. UKFmodified and SRUKF can always work well, indicating their better scalability mainly due to the enhanced numerical stability.

dynamic state estimation↗

Sketch-To-Solution: An Exploration of Viscous CFD with Automatic Grids

Numerical simulation of the Reynolds-averaged Navier–Stokes (RANS) equations has become a critical tool for the design of aerospace vehicles. However, the issues that affect the grid convergence of three dimensional RANS solutions are not completely understood, as documented in the AIAA Drag Prediction Workshop series. Grid adaption methods have the potential for increasing the automation and discretization error control of RANS solutions to impact the aerospace design and certification process. The realization of the CFD Vision 2030 Study includes automated management of errors and uncertainties of physics-based, predictive modeling that can set the stage for ensuring a vehicle is in compliance with a regulation or specification by using analysis without demonstration in flight test (i.e., certification or qualification by analysis). For example, the Cart3D inviscid analysis package has automated Cartesian cut-cell gridding with output-based error control. Fueled by recent advances in the fields of anisotropic grid adaptation, error estimation, and geometry modeling, a similar work flow is explored for viscous CFD simulations; where a CFD application engineer provides geometry, boundary conditions, and flow parameters, and the sketch-to-solution process yields a CFD simulation through automatic, error-based, grid adaptation.

Kleb, William L.↗

CORRELATED ERRORS IN EARTH POINTING MISSIONS

Two different Earth-pointing missions dealing with attitude control and dynamics changes illustrate concerns with correlated error sources and coupled effects that can occur. On the OrbView-2 (OV-2) spacecraft, the assumption of a nearly-inertially-fixed momentum axis was called into question when a residual dipole bias apparently changed magnitude. The possibility that alignment adjustments and/or sensor calibration errors may compensate for actual motions of the spacecraft is discussed, and uncertainties in the dynamics are considered. Particular consideration is given to basic orbit frequency and twice orbit frequency effects and their high correlation over the short science observation data span. On the Tropical Rainfall Measuring Mission (TRMM) spacecraft, the switch to a contingency Kalman filter control mode created changes in the pointing error patterns. Results from independent checks on the TRMM attitude using science instrument data are reported, and bias shifts and error correlations are discussed. Various orbit frequency effects are common with the flight geometry for Earth pointing instruments. In both dual-spin momentum stabilized spacecraft (like OV-2) and three axis stabilized spacecraft with gyros (like TRMM under Kalman filter control), changes in the initial attitude state propagate into orbit frequency variations in attitude and some sensor measurements. At the same time, orbit frequency measurement effects can arise from dynamics assumptions, environment variations, attitude sensor calibrations, or ephemeris errors. Also, constant environment torques for dual spin spacecraft have similar effects to gyro biases on three axis stabilized spacecraft, effectively shifting the one-revolution-per-orbit (1-RPO) body rotation axis. Highly correlated effects can create a risk for estimation errors particularly when a mission switches an operating mode or changes its normal flight environment. Some error effects will not be obvious from attitude sensor measurement residuals, so some independent checks using imaging sensors are essential and derived science instrument attitude measurements can prove quite valuable in assessing the attitude accuracy.

Steve Bilanow↗

Error analysis of numerical methods for thick diffusive neutron transport problems on Shishkin mesh

A thin layer will develop at the boundary if the incoming angular flux is anisotropic in thick diffusive neutron transport problems. Solving such singularly perturbed problems, which have non-smooth solutions with singularity near the boundary, is computationally challenging. Standard finite difference schemes on a uniform mesh cannot yield ε-uniform convergence, where ε is a small parameter, while it can be achieved on a suitable piecewise-uniform Shishkin mesh. We present a formal error analysis of the diamond difference (DD) method and step difference (SD) method for solving the S{sub N} neutron transport equation. The analysis can be extended to other finite difference methods. Numerical results are presented to confirm the error estimates and the advantages of the Shishkin mesh. (author)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Absolute magnitude calibration using trigonometric parallax - Incomplete, spectroscopic samples

A new numerical algorithm is used to calibrate the absolute magnitude of spectroscopically selected stars from their observed trigonometric parallax. This procedure, based on maximum-likelihood estimation, can retrieve unbiased estimates of the intrinsic absolute magnitude and its dispersion even from incomplete samples suffering from selection biases in apparent magnitude and color. It can also make full use of low accuracy and negative parallaxes and incorporate censorship on reported parallax values. Accurate error estimates are derived for each of the fitted parameters. The algorithm allows an a posteriori check of whether the fitted model gives a good representation of the observations. The procedure is described in general and applied to both real and simulated data.

Ratnatunga, Kavan U.↗

Frequency Domain Detection and Precoding for Massive MIMO With Single Carrier Modulation

Single carrier modulation (SCM) schemes are attractive for uplink (UL) transmissions due to improved power efficiency at the user equipment (UE) transmitter compared with multi-carrier modulation schemes. In a massive MIMO scenario with SCM, the UL detection must mitigate the effects of inter-symbol interference and multiuser interference. This processing is effectively performed in the frequency domain (FD) using a minimum mean squared error (MMSE) detector when the transmission is framed with a cyclic prefix. This paper presents a MMSEbased detector that is compatible with distributed processing in a time-division duplex (TDD) system. The matrix inverses computed for the UL detection are then reused to perform multi-user precoding for the downlink (DL). We find that this scheme yields a tremendous savings in computational complexity compared to commonly used zero-forcing (ZF) precoding without sacrificing any performance. Since MMSE processing introduces a bias to the estimates, we then derive the scalar coefficients necessary to cancel the MMSE bias. The impact of channel estimation errors are analyzed for both the UL and DL cases in conjunction with a power-efficient approach to SCM channel estimation. Moreover, extensive simulations are performed to confirm our theoretical findings.

42 ENGINEERING↗

Soft X-ray spectroscopy of three extragalactic sources

Soft X-ray spectra (0.5 to 5 KeV) acquired with a rocket-borne argon-methane proportional counter are reported for M87, 3C 273, and NGC 4151. The counter sensitivity range allowed derivation of simultaneous information on the magnitude of soft X-ray absorption and the slope of the hard X-ray spectrum. Error estimation techniques for the free parameters of X-ray spectra are analyzed, and the results are applied to the spectra previously reported for these sources. It is shown that the technique used to analyze the previous spectra can drastically underestimate the magnitude of errors, and it is concluded that the proposed division of extragalactic X-ray sources into two groups according to the magnitude of absorption in their spectra is premature.

Margon, B.↗