Search NASA⌕ Search

SEARCH · Search NASA

Results for “flat geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Geometric prepatterning-based tuning of the period doubling onset strain during thin-film wrinkling

Wrinkling of thin films is an easy-to-implement and low-cost technique to fabricate stretch-tunable periodic micro and nanoscale structures. However, the tunability of such structures is often limited by the emergence of an undesirable period-doubled mode at high strains. Predictively tuning the onset strain for period doubling via existing techniques requires one to have extensive knowledge about the nonlinear pattern formation behavior. Herein, a geometric prepatterning-based technique is introduced that can be implemented even with limited system knowledge to predictively delay period doubling. The technique comprises prepatterning the film/base bilayer with a sinusoidal pattern that has the same period as the natural period of the system. This technique has been verified via physical and computational experiments on the polydimethylsiloxane (PDMS)/glass bilayer system. It is observed that the onset strain can be increased from the typical value of 20% for flat films to greater than 30% with a modest prepattern aspect ratio (2·amplitude/period) of 0.15. In addition, finite element simulations reveal that (i) the onset strain increases with increasing prepattern amplitude and (ii) the delaying effect can be captured entirely by the prepattern geometry. Therefore, one can implement this technique even with limited system knowledge, such as material properties or film thickness, by simply replicating pre-existing wrinkled patterns to generate prepatterned bilayers. Furthermore, geometric prepatterning is a practical scheme to increase the operating range of stretch-tunable wrinkle-based devices by at least 50%.

36 MATERIALS SCIENCE↗

Inlet boundary-layer shapes on four aircraft forebodies at Mach 6

Boundary-layer shape measurements at the engine inlet on four different hypersonic aircraft forebody designs (with no engine on the forebody) are reported. The measurements provide a qualitative assessment of the effectiveness of various forebody geometries as engine inlet precompression surfaces. The designs, tested in a hypersonic tunnel at Mach 6 and a nominal freestream Reynolds number of 30,500,000, included a semiconical forebody, a configuration similar to a slab delta wing, a conical nose blended into a flat surface, and a conical, complex forebody shape. Boundary layer height as a function of forebody compression is shown for each design.

Lawing, P. L.↗

The effect of channel convergence on heat transfer in a passage with short pin fins

Array averaged heat transfer coefficients were obtained for two configurations of short pin fins in a converging channel and for two flat plate configurations in a converging channel. The effect of flow acceleration due to channel convergence and the effect of varying pin length on the heat transfer was determined. Results are presented in the form of Nusselt number versus Reynolds number for the four geometries tested.

Brigham, B. A.↗

Overview of LANL short-pulse ion acceleration activities

An overview of Los Alamos National Laboratory's activities related to short-pulse ion acceleration is presented. LANL is involved is several projects related to Inertial Confinement Fusion (Fast Ignition) and Laser-Ion Acceleration. LANL has an active high energy X-ray backlighter program for radiographing ICF implosions and other High Energy Density Laboratory Physics experiments. Using the Trident 200TW laser we are currently developing high energy photon (>10 keV) phase contrast imaging techniques to be applied on Omega and the NIF. In addition we are engaged in multiple programs in laser ion acceleration to boost the ion energies and efficiencies for various potential applications including Fast Ignition, active material interrogation, and medical applications. Two basic avenues to increase ion performance are currently under study: one involves ultra-thin targets and the other involves changing the target geometry. We have recently had success in boosting proton energies above 65 MeV into the medical application range. Highlights covered in the presentation include: The Trident Laser System; X-ray Phase Contrast Imaging for ICF and HEDLP; Improving TNSA Ion Acceleration; Scaling Laws; Flat Targets; Thin Targets; Cone Targets; Ion Focusing;Trident; Omega EP; Scaling Comparisons; and, Conclusions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cone-beam breast computed tomography with a displaced flat panel detector array

Purpose: In cone-beam computed tomography (CBCT), and in particular in cone-beam breast computed tomography (CBBCT), an important issue is the reduction of the image artifacts produced by photon scatter and the reduction of patient dose. In this work, the authors propose to apply the detector displacement technique (also known as asymmetric detector or ''extended view'' geometry) to approach this goal. Potentially, this type of geometry, and the accompanying use of a beam collimator to mask the unirradiated half-object in each projection, permits some reduction of radiation dose with respect to conventional CBBCT and a sizeable reduction of the overall amount of scatter in the object, for a fixed contrast-to-noise ratio (CNR). Methods: The authors consider a scan configuration in which the projection data are acquired from an asymmetrically positioned detector that covers only one half of the scan field of view. Monte Carlo simulations and measurements, with their CBBCT laboratory scanner, were performed using PMMA phantoms of cylindrical (70-mm diameter) and hemiellipsoidal (140-mm diameter) shape simulating the average pendant breast, at 80 kVp. Image quality was evaluated in terms of contrast, noise, CNR, contrast-to-noise ratio per unit of dose (CNRD), and spatial resolution as width of line spread function for high contrast details. Results: Reconstructed images with the asymmetric detector technique deviate less than 1% from reconstruction with a conventional symmetric detector (detector view) and indicate a reduction of the cupping artifact in CT slices. The maximum scatter-to-primary ratio at the center of the phantom decreases by about 50% for both small and large diameter phantoms (e.g., from 0.75 in detector view to 0.40 in extended view geometry at the central axis of the 140-mm diameter PMMA phantom). Less cupping produces an increase of the CT number accuracy and an improved image detail contrast, but the associated increase of noise observed may produce a decrease of detail CNR. By simulating the energy deposited inside the phantoms, the authors evaluated a maximum 50% reduction of the absorbed dose at the expense of a decrease of CNR, for the half beam irradiation of the object performed with the displaced detector technique with respect to full beam irradiation. The decrease in CNR, and in absorbed dose as well, translates into a detail CNRD showing values comparable to or higher than the ones obtained for a conventional symmetric detector technique, attributed to the effect of decreased scatter in particular at the axis of the irradiated object. An estimate is provided (about 12%) for the average dose reduction possible in CBBCT at constant CNR for the average uncompressed breast (14 cm diameter, 50% glandularity), in case of minimum image overlapping in extended view. Conclusions: Simulations and experiments show that CBCT reconstructions with the displaced detector technique and with a half beam collimator are less affected by scatter artifacts, which could lead to some decrease of the radiation dose to the irradiated object with respect to a conventional reconstruction. This dose reduction is associated with increase of noise, decrease of CNR, but equal or improved CNRD values. The use of a small area detector would allow also to reduce the apparatus cost and to improve the data transfer speed with a corresponding increment of frame rate.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Parametric modelling of a reconfigurable wave energy device

To date, one of the difficulties with wave energy devices is modulating the power transfer from the waves to the generator. In wind turbines, this is achieved by turbine pitch control, leading to the ubiquitous flat power curve. Recently, a wave energy converter, having moveable vanes, has been developed by the National Renewable Energy Laboratory (NREL) in the US. Furthermore, this paper described the development of a compact hydrodynamic model for the NREL device, based on multiple linear hydrodynamic modelling (Murray-Smith and Johansen, 1997), which can be used to model the hydrodynamic behaviour of the device across its full operational spectrum of vane angles. To show the utility of the model, we demonstrate a flat power curve for the WEC, using the vane angles as a control input.

16 TIDAL AND WAVE POWER↗

Two-point correlation functions in inhomogeneous and anisotropic cosmologies

Two-point correlation functions are ubiquitous tools of modern cosmology, appearing in disparate topics ranging from cosmological inflation to late-time astrophysics. When the background spacetime is maximally symmetric, invariance arguments can be used to fix the functional dependence of this function as the invariant distance between any two points. In this paper we introduce a novel formalism which fixes this functional dependence directly from the isometries of the background metric, thus allowing one to quickly assess the overall features of Gaussian correlators without resorting to the full machinery of perturbation theory. As an application we construct the CMB temperature correlation function in one inhomogeneous (namely, an off-center LTB model) and two spatially flat and anisotropic (Bianchi) universes, and derive their covariance matrices in the limit of almost Friedmannian symmetry. We show how the method can be extended to arbitrary N -point correlation functions and illustrate its use by constructing three-point correlation functions in some simple geometries.

79 ASTRONOMY AND ASTROPHYSICS↗

Measurements of plasma parameters in the divertor island of Wendelstein 7-X through line-ratio spectroscopy on helium

We report electron temperature T e and density n e have been measured in the divertor island of Wendelstein 7-X by means of a new thermal He-beam system utilizing line-ratio spectroscopy. This system is equipped with a poloidal arrangement of five gas valves that allows to infer 2D plasma profiles T e ( R,Z ) and n e ( R,Z ) across the magnetic island forming the island divertor. A local maximum in T e ( R,Z ) was measured along the flux surfaces located between the island center and the outer separatrix. In the island center, characterized by closed field lines, a clear local minimum in T e was measured, indicating that no direct heat deposition occurs in this region and that the perpendicular heat flux from the core plasma into this domain is small. Increasing the island size leads to a reduction of the connection length in the scrape-off layer (SOL) and to a shift of the island center towards the divertor target. In this scenario, the T e ( R,Z ) are reduced in the entire island domain. Density profiles are found flat across the divertor island for both island size scenarios. These findings are supported by similar observations made with a reciprocating probe plunging through the same SOL island at the mid-plane of W7-X representing the upstream position in this 3D divertor geometry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multi-institutional dosimetric and geometric commissioning of image-guided small animal irradiators

Purpose: To compare the dosimetric and geometric properties of a commercial x-ray based image-guided small animal irradiation system, installed at three institutions and to establish a complete and broadly accessible commissioning procedure. Methods: The system consists of a 225 kVp x-ray tube with fixed field size collimators ranging from 1 to 44 mm equivalent diameter. The x-ray tube is mounted opposite a flat-panel imaging detector, on a C-arm gantry with 360° coplanar rotation. Each institution performed a full commissioning of their system, including half-value layer, absolute dosimetry, relative dosimetry (profiles, percent depth dose, and relative output factors), and characterization of the system geometry and mechanical flex of the x-ray tube and detector. Dosimetric measurements were made using Farmer-type ionization chambers, small volume air and liquid ionization chambers, and radiochromic film. The results between the three institutions were compared. Results: At 225 kVp, with 0.3 mm Cu added filtration, the first half value layer ranged from 0.9 to 1.0 mm Cu. The dose-rate in-air for a 40 × 40 mm{sup 2} field size, at a source-to-axis distance of 30 cm, ranged from 3.5 to 3.9 Gy/min between the three institutions. For field sizes between 2.5 mm diameter and 40 × 40 mm{sup 2}, the differences between percent depth dose curves up to depths of 3.5 cm were between 1% and 4% on average, with the maximum difference being 7%. The profiles agreed very well for fields >5 mm diameter. The relative output factors differed by up to 6% for fields larger than 10 mm diameter, but differed by up to 49% for fields ≤5 mm diameter. The mechanical characteristics of the system (source-to-axis and source-to-detector distances) were consistent between all three institutions. There were substantial differences in the flex of each system. Conclusions: With the exception of the half-value layer, and mechanical properties, there were significant differences between the dosimetric and geometric properties of the three systems. This underscores the need for careful commissioning of each individual system for use in radiobiological experiments.

61 RADIATION PROTECTION AND DOSIMETRY↗

Simultaneous measurement of linear and transverse displacements by laser self-mixing

We present a contactless optical sensor based on the laser-self-mixing effect for real-time measurement of linear and transverse displacements of a moving stage. The sensor is able to measure linear displacements of up to 400 mm along the main optical axis while simultaneously estimating straightness and flatness deviations up to 1 mm. The sensor exploits two identical coplanar nonparallel self-mixing interferometers and requires only one reference plane. The reduction in the number of optical elements allowed by the self-mixing configuration and the intrinsic stiffness of the adopted geometry result in a compact, low-cost, and easy-to-align setup.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

PTT System Performance Evaluation in 3-D Imaging of AM Components

Additive manufacturing (AM, or 3D printing) for commercial nuclear energy applications is an emerging method for cost-efficient manufacturing aimed at replacing aging nuclear reactor parts and reducing costs for new construction. Because of the geometry of metallic structures of interest for nuclear applications, which consist of planar primitives with no symmetry of revolution, limited options are available for non-destructive evaluation (NDE) either during or post manufacturing. Known material flaws in AM include low density regions consisting of nonsintered powder, which have to be detected to ensure the safety of long-term performance nuclear reactor components. As a solution to NDE of AM, we are developing pulsed thermal tomography (PTT) models and depth inversion algorithms for 3D imaging. PTT has many advantages because the method is non-contact and allows for in-service, NDE of AM nuclear reactor parts. By analyzing transients of surface temperature response due to internal thermal resistances, one can obtain 3D reconstructions of material effusivity using a unique inversion algorithm developed at Argonne. This study investigates the capability of PTT in imaging several AM structures fabricated from Inconel 718 (IN718) feedstock. The AM structures have complex geometry, but do not have calibrated internal defects. The objective is to determine PTT settings, such as the total integration time, for imaging of representative AM structures. A new FLIR X8500sc IR camera with higher spatial resolution (1280x1024 at 181Hz frame rate) was integrated into the PTT laboratory setup. Software tools were developed to ensure compatibility of new camera files with legacy effusivity reconstruction codes. The new camera was used to obtain 3-D reconstructions of IN718 nozzle plate and a particle filter plate. The results demonstrate the capability of PTT in 3- D imaging of complex geometry AM structures. Further, increased resolution imaging is achieved compared to prior results using older FLIR SC4000 IR camera. In addition, preliminary studies were conducted on developing image processing algorithms for automated detection of flaws. Initial demonstrations are shown for segmentation of PTT images of flat bottom hole (FBH) specimens. Imaging of FBH specimens was described in a prior report. Intermediate results demonstrated in this report will be developed further in detection of flaws in AM specimens.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Computerized multilevel analysis for multilayered fiber composites

A FORTRAN 4 computer code for the micromechanics, macromechanics, and laminate analysis of multilayered fiber composite structural components is described. The code can be used either individually or as a subroutine within a complex structural analysis/synthesis program. The inputs to the code are constituent materials properties, composite geometry, and loading conditions. The outputs are various properties for ply and composite; composite structural response, including bending-stretching coupling; and composite stress analysis, including comparisons with failure criteria for combined stress. The code was used successfully in the analysis and structural synthesis of flat panels, in the buckling analysis of flat panels, in multilayered composite material failure studies, and lamination residual stresses analysis.

Chamis, C. C.↗

Computerized multilevel analysis for multilayered fiber composites.

A FORTRAN IV computer code for the micromechanics, macromechanics, and laminate analysis of multilayered fiber composite structural components is described. The code can be used either individually or as a subroutine within a complex structural analysis/synthesis program. The inputs to the code are constituent materials properties, composite geometry, and loading conditions. The outputs are various properties for ply and composite; composite structural response, including bending-stretching coupling; and composite stress analysis, including comparisons with failure criteria for combined stress. The code was used successfully in the analysis and structural synthesis of flat panels, in the buckling analysis of flat panels, in multilayered composite material failure studies, and lamination residual stresses analysis.

Chamis, C. C.↗

Biaxial load effects in fracture mechanics

It is found that the standard expressions for elastic stress and displacement in the crack-tip region (i.e., the so-called singular solution) cannot be considered to be approximations that are acceptable in a completely general sense. This conclusion is best illustrated by the instance of a biaxially loaded infinite sheet with a flat horizontal central crack, where the effect of load applied parallel to the plane of the crack appears entirely in the second terms of the series representations for local stresses and displacements. An elastoplastic finite-element analysis of the same biaxially loaded finite specimen geometry shows that the global energy release rate, the J-integral, the plastic stress and strain intensity factors (in the sense of Hilton and Hutchinson), and the size of the crack border region plastic yield, all have pronounced biaxial load dependence.

Liebowitz, H.↗

Digital filter design for radar image formation

Novel weighted-least-squares approaches to the design of digital filters for SAR applications are presented. The filters belong to three different categories according to their combinations of minimax passband, least-squares stopband, minimax stopband, and maximally-flat passband. For real-time applications, it is important to design the sets of digital filter coefficient tables in an offline environment; the appropriate precomputed filter is then selected for each SAR signal-processing function, as a function of both mode and mapping geometry during real-time processing.

Adams, John W.↗

Geologic Mapping of the Martian Impact Crater Tooting

Tooting crater is approximately 29 km in diameters, is located at 23.4 deg N, 207.5 deg E and is classified as a multi-layered ejecta crater. Tooting crater is a very young crater, with an estimated age of 700,000 to 2M years. The crater formed on virtually flat lava flows within Amazonis Planitia where there appears to have been no major topographic features prior to the impact, so that we can measure ejecta thickness and cavity volume. In the past 12 months, the authors have: published their first detailed analysis of the geometry of the crater cavity and the distribution of the ejecta layers; refined the geologic map of the interior of Tooting crater through mapping of the cavity at a scale of 1:1100K; and continued the analysis of an increasing number of high resolution images obtained by the CTX and HiRISE instruments. Currently the authors seek to resolve several science issues that have been identified during this mapping, including: what is the origin of the lobate flows on the NW and SW rims of the crater?; how did the ejecta curtain break apart during the formation of the crater, and how uniform was the emplacement process for the ejecta layers; and, can we infer physical characteristics about the ejecta? Future study plans include the completion of a draft geologic map of Tooting crater and submission of it to the U.S. Geological survey for a preliminary review, publishing a second research paper on the detailed geology of the crater cavity and the distribution of the flows on the crater rim, and completing the map text for the 1:100K geologic map description of units at Tooting crater.

Mouginis-Mark, Peter↗

Measurement of the Noise Resulting from the Interaction of Turbulence with a Lifting Surface

An experimental study of the noise resulting from the interaction of an airfoil with incident turbulence is presented. The test models include NACA0015 airfoils of different chord lengths, a flat plate with a sharp leading edge, and an airfoil of same section as a reference Fowler flap. The airfoils are immersed in nearly isotropic turbulence. Two approaches for performing the noise measurements are used and compared. The effects that turbulence intensity and scales, airfoil geometry, velocity and angle of attack have on the incident turbulence interaction noise are examined. Detailed directivity measurements are presented. It is found that noise spectral levels beyond the peak frequency decrease more with decreasing airfoil leading edge sharpness, and that spectral peak level (at 0 deg. angle of attack) appears to be mostly controlled by the airfoil fs thickness and chord. Increase in turbulence scale and intensity are observed to lead to a uniform increase of the noise spectral levels with an LI(sup 2) dependence (where L is the turbulence longitudinal integral scale and I is the turbulence intensity). Noise levels are found to scale with the 6th power of velocity and the 2nd power of the airfoil chord. Sensitivity to changes in angle of attack appears to have a turbulence longitudinal integral scale to chord (C) ratio dependence, with large effects on noise for L/C greater than or equal to 1 and decreased effects as L/C becomes smaller than 1. For all L/C values, the directivity pattern of the noise resulting from the incident turbulence is seen to remain symmetric with respect to the direction of the mean flow until stall, at which point, the directivity becomes symmetric with respect to the airfoil chord. It is also observed that sensitivity to angle of attack changes is more pronounced on the model suction side than on the model pressure side, and in the higher frequency range of the spectra for the largest airfoils tested (L/C less than 0.24).

Hutcheson, Florence V.↗

Shielding Characteristics Using an Ultrasonic Configurable Fan Artificial Noise Source to Generate Modes - Experimental Measurements and Analytical Predictions

An Ultrasonic Configurable Fan Artificial Noise Source (UCFANS) was designed, built, and tested in support of the NASA Langley Research Center's 14x22 wind tunnel test of the Hybrid Wing Body (HWB) full 3-D 5.8% scale model. The UCFANS is a 5.8% rapid prototype scale model of a high-bypass turbofan engine that can generate the tonal signature of proposed engines using artificial sources (no flow). The purpose of the program was to provide an estimate of the acoustic shielding benefits possible from mounting an engine on the upper surface of a wing; a flat plate model was used as the shielding surface. Simple analytical simulations were used to preview the radiation patterns - Fresnel knife-edge diffraction was coupled with a dense phased array of point sources to compute shielded and unshielded sound pressure distributions for potential test geometries and excitation modes. Contour plots of sound pressure levels, and integrated power levels, from nacelle alone and shielded configurations for both the experimental measurements and the analytical predictions are presented in this paper.

Artifical Noise↗