Results for “friction data” — Page 40

NASA NTRS1983

Dynamic crystallization experiments as constraints on chondrule genesis

The effectiveness of dynamic recrystallization experiments to reconstruct chondrule textures is evaluated. Consideration is given to the results of several experimental simulations of the silicate spheres of pyroxene-olivine chondrules, Si-rich chondrules, chondrites, droplet chondrules, and microporphyritic chondrules. It is shown that many chondrules have textures consistent with heating to 1400-1600 C, and cooling rates from a few degrees to several thousands of degrees per hour. It is shown that this physical constraint effectively rules out mechanisms for chondrule genesis which do not require instantaneous or very slow cooling. Analysis of the available textural, chemical, and isotopic data suggest that chondrules were generated from primordial particles, and several mechanisms might have assisted in chondrule heating as they settled down toward the median plane of the nebula. The most important of these mechanisms appear to be friction with the nebular gas and heating by flares.

Hewins, R. H.↗

NASA NTRS1999

HSCT Propulsion Airframe Integration Studies

The Lockheed Martin spillage study was a substantial effort and is worthy of a separate paper. However, since a paper was not submitted a few of the most pertinent results have been pulled out and included in this paper. The reader is urged to obtain a copy of the complete Boeing Configuration Aerodynamics final 1995 contract report for the complete Lockheed documentation of the spillage work. The supersonic cruise studies presented here focus on the bifurcated - axisymmetric inlet drag delta. In the process of analyzing this delta several test/CFD data correlation problems arose that lead to a correction of the measured drag delta from 4.6 counts to 3.1 counts. This study also lead to much better understanding of the OVERFLOW gridding and solution process, and to increased accuracy of the force and moment data. Detailed observations of the CFD results lead to the conclusion that the 3.1 count difference between the two inlet types could be reduced to approximately 2 counts, with an absolute lower bound of 1.2 counts due to friction drag and the bifurcated lip bevel.

Chaney, Steve↗

NASA NTRSDate not supplied

LS-DYNA User-Defined Internal Ballistic Modeling

LS-DYNA Explicit Finite Element Analysis software and CADPROG Internal Ballistic Analysis code are integrated as a single modeling tool to analyze pyro-mechanical devices. Coupling these two codes allows the ballistic calculations to be performed without modeling the propellant in an FEA mesh. At each LS-DYNA time step, CADPROG is run analytically using the kinematic data (stroke, velocity, chamber volume) fed back from the LS-DYNA simulation. The calculated pressure is then applied to a piston or any applicable surface mesh in LS-DYNA model interactively. All external loads such as friction, damping loads, assisting/resisting loads, locking/unlocking loads are modeled in LS-DYNA and coupled with pressure loads from CADPROG to create a fully defined equation of motion Both codes are written in Fortran 77. CADPROG is integrated in the LS-DYNA source code as a user-defined subroutine and recompiled to generate a custom executable.

pyrotechnics↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 1

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024). Three distinct rounds of FSP experiments were performed by the experimental team, producing replicate samples utilizing across different nominal processing conditions (Condition IDs) listed in Table 1. The starting material on which FSP was applied was commercially available unprocessed stainless-steel type 316L material. Chosen processing conditions were very diverse, and some were intentionally chosen to produce defects. Several samples experienced tool breakage during experimentation, so a full set of three replicates was not produced for every nominal processing condition.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 2

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024).

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 3

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024).

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 4

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024).

36 MATERIALS SCIENCE↗

NASA NTRS1975

Verification of a landing dynamics computer program using Viking Lander data

An investigation was conducted to verify the accuracy of the Landing Dynamics Computer Program (LDCP) used to simulate the landing event of the Viking Lander (VL) on to the Martian surface. This verification was achieved by comparing the analytical data with results from a test program involving a dynamically scaled model of a VL configuration. A secondary objective of this study was to evaluate the sensitivity of the VL to initial rates and orientations, configuration modifications, and footpad friction.

Muraca, R. J.↗

NASA NTRS1983

Materials investigation of STS-3 parachute failure

Main parachute, No. 2 of SRB A-12 on STS-3, sustained damage during deployment or initial inflation that resulted in its collapse and failure to sustain load. During an investigation of the materials from this parachute, optical and scanning electron microscope analyses were conducted. This examination identified stains and abrasions on vent lines that appear to have been a result of friction contact with its flotation bag lanyard. Mechanical testing of the vent band indicated a reduction in strength of 37 percent obviously due to structural overload, heat, and ocean water exposure. It is concluded from this and other available data that entanglement of parachutes No. 1 and No. 2 during deployment caused adequate structural damage to main parachute No. 2 to render it unable to carry load.

Nichols, R. L.↗

NASA NTRS1988

Microgravity two-phase fluid flow pattern modeling

When gas and liquid mixtures flow in a pipe, the distribution of the two phases may take many forms. A flow pattern, or flow regime, is the characteristic spatial distribution of the phases of flow in a pipe. Because heat transfer and pressure drop are dependent on the characteristic distribution of phases, it is necessary to describe flow patterns in an appropriate manner so that a hydrodynamic or heat transfer theory applicable to that can be chosen. A theoretical two phase flow regime transition map under a microgravity environment was developed on physical concepts. These transitions use four basic flow patterns: dispersed flow, slug flow, stratified flow, and annular flow. The forces considered are body force, surface tension force, inertial force, friction, and the force from eddy turbulent fluctuation. Three dimensionless parameters were developed. Because these transition boundaries were developed based on physical concepts, they should be applicable to flow regimes occurring in various design conditions. Because the flow pattern data from KC-135 experiments are insufficient to verify these theoretical transition lines completely, an adiabatic experiment for flow regime analysis is recommended.

Lee, Doojeong↗

NASA NTRS1948

An Analytical Method of Estimating Turbine Performance

A method is developed by which the performance of a turbine over a range of operating conditions can be analytically estimated from the blade angles and flow areas. In order to use the method, certain coefficients that determine the weight flow and friction losses must be approximated. The method is used to calculate the performance of the single-stage turbine of a commercial aircraft gas-turbine engine and the calculated performance is compared with the performance indicated by experimental data. For the turbine of the typical example, the assumed pressure losses and turning angles give a calculated performance that represents the trends of the experimental performance with reasonable accuracy. The exact agreement between analytical performance and experimental performance is contingent upon the proper selection of the blading-loss parameter. A variation of blading-loss parameter from 0.3 to 0.5 includes most of the experimental data from the turbine investigated.

Kochendorfer, Fred D↗

NASA NTRS1949

An analytical method of estimating turbine performance

A method is developed by which the performance of a turbine over a range of operating conditions can be analytically estimated from the blade angles and flow areas. In order to use the method, certain coefficients that determine the weight flow and the friction losses must be approximated. The method is used to calculate the performance of the single-stage turbine of a commercial aircraft gas-turbine engine and the calculated performance is compared with the performance indicated by experimental data. For the turbine of the typical example, the assumed pressure losses and the tuning angles give a calculated performance that represents the trends of the experimental performance with reasonable accuracy. The exact agreement between analytical performance and experimental performance is contingent upon the proper selection of a blading-loss parameter.

Kochendorfer, Fred D↗

NASA NTRS1996

High Reynolds number analysis of flat plate and separated afterbody flow using non-linear turbulence models

The ability of the three-dimensional Navier-Stokes method, PAB3D, to simulate the effect of Reynolds number variation using non-linear explicit algebraic Reynolds stress turbulence modeling was assessed. Subsonic flat plate boundary-layer flow parameters such as normalized velocity distributions, local and average skin friction, and shape factor were compared with DNS calculations and classical theory at various local Reynolds numbers up to 180 million. Additionally, surface pressure coefficient distributions and integrated drag predictions on an axisymmetric nozzle afterbody were compared with experimental data from 10 to 130 million Reynolds number. The high Reynolds data was obtained from the NASA Langley 0.3m Transonic Cryogenic Tunnel. There was generally good agreement of surface static pressure coefficients between the CFD and measurement. The change in pressure coefficient distributions with varying Reynolds number was similar to the experimental data trends, though slightly over-predicting the effect. The computational sensitivity of viscous modeling and turbulence modeling are shown. Integrated afterbody pressure drag was typically slightly lower than the experimental data. The change in afterbody pressure drag with Reynolds number was small both experimentally and computationally, even though the shape of the distribution was somewhat modified with Reynolds number.

Carlson, John R.↗

NASA NTRS1985

Train Analysis

Running resistance, the combined resistance induced by aerodynamic drag and mechanical friction, absorbs about 16 percent of railroad budget and maintenance costs. In order to study these losses, AT&SF Railroad entered into a joint research project with the Jet Propulsion Laboratory. Various train configurations were tested when the resulting data was computer analyzed. The Coast-Down Technique was estimated at one percent accuracy. AT&SF is evaluating the data further.

Source record↗

NASA NTRS1981

A review of flight-to-wind tunnel drag correlation

Comparisons are made of wind-tunnel-model and flight drag data for various configurations representing aircraft from the mid-1940s to the 1970s. Discrepancies between model and flight data such as Reynolds number effects, wall interference, and aeroelastic problems are discussed. String support effects and the inability of models to simulate surface deflections for longitudinal trim are also studied. A wind tunnel-to-flight correlation of turbulent friction drag confirms the incompressible Karman-Schoenherr variation of turbulent skin friction with Reynolds number and the T' method for accounting compressibility effects. NASA tested 10 deg cone research indicates that model tests which are affected by tunnel noise may require the lower disturbance level environment available in flight, and it is concluded that new cryogenic facilities will improve the fidelity of model simulations of full-scale flight flow phenomena.

Saltzman, E. J.↗

NASA NTRS1983

Influence of wall permeability on turbulent boundary-layer properties

Experimental boundary-layer studies of a series of low pressure drop, permeable surfaces have been conducted to characterize their surface interaction with a turbulent boundary layer. The models were flat and tested at nominally zero pressure gradient in low speed air. The surfaces were thin metal sheets with discrete perforations. Direct drag balance measurements of skin friction indicate that the general effect of surface permeability is to increase drag above that of a smooth plate reference level. Heuristic arguments are presented to show that this type of behavior is to be expected. Other boundary-layer data are also presented including mean velocity profiles and conditionally sampled streamwise velocity fluctuations (hot wire) for selected models.

Wilkinson, S. P.↗

NASA NTRS1986

Development of a takeoff performance monitoring system

The development and testing of a real-time takeoff performance monitoring system is discussed. The algorithm is madeup of two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate schedule performance data for that takeoff. The real-time segment uses the scheduled performance data generated in the pretakeoff segment, runway length data, and measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. An important feature of this algorithm is the one-time estimation of the runway rolling friction coefficient. The algorithm was tested using a six degree of freedom airplane model in a computer simulation. Results from a series of sensitivity analysis are also included.

Srivatsan, R.↗

NASA NTRS1987

Development of a takeoff performance monitoring system

Discussed are the development and testing of a real-time takeoff performance monitoring algorithm. The algorithm is made up of two segments: a pretakeoff segment and a real-time segment. One-time imputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data for that takeoff. The real-time segment uses the scheduled performance data generated in the pretakeoff segment, runway length data, and measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. An important feature of this algorithm is the one-time estimation of the runway rolling friction coefficient. The algorithm was tested using a six-degree-of-freedom airplane model in a computer simulation. Results from a series of sensitivity analyses are also included.

Srivatsan, Raghavachari↗