SEARCH · Search NASA

Results for “load testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Assessment of the Uniqueness of Wind Tunnel Strain-Gage Balance Load Predictions

A new test was developed to assess the uniqueness of wind tunnel strain-gage balance load predictions that are obtained from regression models of calibration data. The test helps balance users to gain confidence in load predictions of non-traditional balance designs. It also makes it possible to better evaluate load predictions of traditional balances that are not used as originally intended. The test works for both the Iterative and Non-Iterative Methods that are used in the aerospace testing community for the prediction of balance loads. It is based on the hypothesis that the total number of independently applied balance load components must always match the total number of independently measured bridge outputs or bridge output combinations. This hypothesis is supported by a control volume analysis of the inputs and outputs of a strain-gage balance. It is concluded from the control volume analysis that the loads and bridge outputs of a balance calibration data set must separately be tested for linear independence because it cannot always be guaranteed that a linearly independent load component set will result in linearly independent bridge output measurements. Simple linear math models for the loads and bridge outputs in combination with the variance inflation factor are used to test for linear independence. A highly unique and reversible mapping between the applied load component set and the measured bridge output set is guaranteed to exist if the maximum variance inflation factor of both sets is less than the literature recommended threshold of five. Data from the calibration of a six{component force balance is used to illustrate the application of the new test to real-world data.

strain-gage balance↗

NASA NTRS1976

An evaluation of dry film lubricants and substrate materials for use on SSME gimbal bearings

Failure of the spherical bearing shaft of the Space Shuttle Main Engine (SSME) gimbal bearing assembly was encountered during Design Verification Specification testing of the full scale engine. Investigation revealed that the failure was caused by a deficiency in the lubrication system. Based upon the materials and gimbal operating conditions, a lubricant of MoS2 and graphite with a ceramic binder was the best lubricant candidate for this particular application; however, the decision to implement the change was not made without verification testing. Scaled down simulation testing was performed. Four different substrate materials and eight different dry film lubricants were subjected to tests under simulated SSME environmental and stress load conditions. The test specimens were evaluated for friction and operating life. Each test specimen was subjected to cyclic operation under load until failure. The force required to move the bearing surfaces relative to each other was monitored throughout the test, thus providing analytical data for derivation of the coefficient of friction. Results indicate that the MoS2/graphite lubricant with ceramic binder proved to be superior from the standpoint of endurance and also from the standpoint of friction reducing capabilities when applied to the titanium substrate material used on SSME. Endurance of this lubricant was approximately 16 times that of the lubricant which was being used when the SSME gimbal failed.

Harp, J. A.↗

NASA NTRS1987

Performance and loads data from a hover test of a 0.658-scale V-22 rotor and wing

A hover test of a 0.658-scale model of a V-22 rotor and wing was conducted at the Outdoor Aerodynamic Research Facility at Ames Research Center. The primary objectives of the test were to obtain accurate measurements of the hover performance of the rotor system, and to measure the aerodynamic interactions between the rotor and wing. Data were acquired for rotor tip Mach numbers ranging from 0.1 to 0.73. This report presents data on rotor performance, rotor-wake downwash velocities, rotor system loads, wing forces and moments, and wing surface pressures.

Felker, Fort F.↗

NASA NTRS1984

Transient vibration test criteria for spacecraft hardware

Transient vibration test criteria, developed for spacecraft hardware, provide a test rationale to verify the capability of the hardware to withstand the low and mid frequency transient vibration environments induced by launch vehicle events. A test method, consisting of a series of discrete frequency, limited cycle, modulated sine wave pulses, was developed to avoid the slow swept sine drawbacks, yet provide a repeatable test that would excite all frequencies. The shape of the waveform is that of the classic response of the mass of a one degree of freedom system when it is base-excited by an exponentially decayed sine wave transient. Criteria were developed to define pulse amplitudes, shapes, and center frequencies from spacecraft loads analyses. Test tolerance criteria were also developed and specified. The transient vibration test criteria were implemented on spacecraft flight hardware and provided a more realistic test simulation (i.e., less conservative) for qualification of spacecraft hardware without risk of undertest.

Kern, D. L.↗

NASA NTRS1992

Laboratory evaluation of footings for lunar telescopes

Presented here are the results of laboratory experiments with diffferent footing shapes for lunar telescopes. These experiments used a variety of soils including some to simulate regolith response. Based on what is known of regolith and regolith-structure interaction, a shallow-multiple-contact points footing foundation can be adequately designed to support lunar telescopes. Plane-strain load-displacement tests were conducted with different footings and different lunar simulants in a deep transparent plexiglass container. The model footings considered include the rectangular, hemispherical, and spudcan designs. Simulants used to reproduce the mechanical properties of the lunar regolith were fly ash, crushed basalt with and without glass, and a processed lunar simulant. Load-displacement curves were obtained for the different footings in Ottawa sand and in the crushed basalt with glass. The spudcan footing was found to be self-digging and yet stiff, thus providing excellent lateral stability in a large variety of soils.

Chua, Koon M.↗

NASA NTRS1976

Reliability analysis of structures under periodic proof tests in service

A reliability analysis of structures subjected to random service loads and periodic proof tests treats gust loads and maneuver loads as random processes. Crack initiation, crack propagation, and strength degradation are treated as the fatigue process. The time to fatigue crack initiation and ultimate strength are random variables. Residual strength decreases during crack propagation, so that failure rate increases with time. When a structure fails under periodic proof testing, a new structure is built and proof-tested. The probability of structural failure in service is derived from treatment of all the random variables, strength degradations, service loads, proof tests, and the renewal of failed structures. Some numerical examples are worked out.

Yang, J.-N.↗

NASA NTRS1997

Experimental Investigation of a Graphite-Composite Intertank Section for a Reusable Launch Vehicle

The use of graphite-composites as primary structure is essential for the development of a cost effective single-stage-to-orbit reusable launch vehicle (RLV). A full-scale segment of a graphite-composite intertank was designed and fabricated by an industry team and tested at NASA Langley Research Center as a part of the RLV technology development program. The intertank test component was approximately 3.0 m long by 6.7 m wide and included slightly less than a 90deg section of a cylindrical intertank. The test article was fabricated using graphite-bismaelimide composite material and consisted of a hat-stiffened skin with five ring frames. The stiffeners were secondarily bonded to the panel skin and the ring frames were mechanically attached. The test article was loaded to failure with a uniform compression load applied by 21 individually controlled hydraulic actuators. Resistance strain gages, linear variable differential transformers and video cameras were used to measure and record the test results. A linear f d t e element analysis of the test article and test fixture was performed. The test results verified the structural integrity cf the intertank test article up to the design limit load. However, the test article failed in general skin buckling between the ring frames at a load 1.08 times design limit load. This load was considerably lower than the expected failure load. The cause of premature failure is being investigated. Good correlation of the test and analysis results was obtained for loads up to the design limit load.

Sawyer, James Wayne↗

NASA NTRS2010

Ultrasonic Monitoring of Ply Crack and Delamination Formation in Composite Tube Under Torsion Load

As a simple model of a rotor spar, a circular graphite-epoxy composite laminate cylinder was subjected to cyclic torsional load. The test section of the cylindrical specimen varied from four to six plies of plus or minus 45 degree fibers, due to intentional ply overlaps and gaps. A layer of 13-micrometer Teflon film was inserted between plies at three locations to serve as delamination initiators. A commercial X-Y scanner was mounted to the load frame to enable ultrasonic inspection without removing the specimen. A focused immersion probe was mounted in a captive water column with a rugged Nitrile membrane tip, which was coupled to the cylinder using a mist of soapy water. The transducer was aligned normal to the cylinder surface using the X-axis. Scanning was performed along the length of the specimen with the Y-axis and the specimen was incrementally rotated by the torsion head of the load frame. After 350k cycles of torsion, several linear 45 degree diagonal indications appeared as 5-40% attenuation of the back wall echo, with no apparent echoes from the interior of the composite, suggesting through-ply cracks in the innermost ply. Crack indications grew and new cracks appeared as torsion cycling continued. Internal reflections from delaminations associated with the growing ply cracks appeared after 500k cycles. Three areas of extensive multi-layer delaminations appeared after 1150k cycles. Failure of the specimen occurred at 1600k cycles. The observed progressive damage was not associated with the Teflon inclusions. Concurrent thermographic measurements provided lower resolution confirmation of the damage observed.

Johnston, P. H.↗

DOE OSTI2026

Gigacycle Fatigue Strength Evaluation of Welded 316L Stainless Steels for Mercury Target Vessel

At the Materials and Life Science Experimental Facility (MLF) in J-PARC, liquid mercury target for the pulsed spallation neutron source is in operation. An enclosure vessel for the liquid mercury target made of type 316L stainless steel (SS316L) suffers two kinds of cyclic stress during operation. One is the thermal stress due to the internal heating and swings by proton beam trip. The other is the impulsive stress by the pressure waves generated by the proton beam injection. The total number of loading cycles for the former is ∼104, and the latter is ∼4 × 108 for a year operation in the J-PARC mercury target vessel. The target vessel is assembled by an electron beam welding (EBW) and a gas tungsten arc welding (GTAW). However, fatigue data of welded SS316L up to gigacycle is limited. Ultrasonic fatigue testing, applying load cycles by utilizing ultrasonic resonance, for the welded SS316L was performed to investigate the effect of welding on fatigue behavior up to a gigacycle. The result showed that the fatigue strength degradation by EBW and EBW with GTAW were not recognized up to 109 cycles. Crack initiation in welded specimens nucliated at off-center areas of the specimen whereas the cracks in base metal specimen originated at the specimen center.

Naoe, Takashi [Japan Atomic Energy Agency (JAEA)]↗

DOE OSTI2026

Induction Melter Processing Alternatives for High Level Radioactive Wastes – 26198

This work investigates the potential to vitrify nuclear fuel directly, as well as the vitrification potential associated with experimental dissolver solutions. Greater understanding of the exothermicity is needed to quantify processing risk, especially with respect to potential phase changes and associated explosion hazards present in some systems. Thermal analysis was carried out on various simulants to elucidate the exothermic reaction potential from solid metal dissolution in glass and from the drying of alternative process dissolver solutions. Results from experimental testing of simulants to demonstrate vitrification potential and compatibility indicate that alternative dissolver flowsheets suppress the heat released during processing and that common silicate- and phosphate- based glass systems are potential candidates for direct vitrification. Direct vitrification (conversion) of fuel simulants was assessed using laboratory scale glass melts to obtain qualitative information on dissolution rates and waste loadings. Initial tests were successful to dissolve and incorporate metal directly into glass, although the kinetics and limits of dissolution and incorporation into glass are not fully understood.

Amoroso, Jake [Savannah River National Laboratory ↗

NASA NTRS1970

Design and Manufacture of Wheels for A Dual-Mode (Manned - Automatic) Lunar Surface Roving Vehicle. Volume 1: Detailed Technical Report

The concept development, testing, evaluation, and the selection of a final wheel design concept for a dual-mode lunar surface vehicle (DLRV) is detailed. Four wheel configurations were fabricated (one open wheel and three closed wheel) (and subjected to a series of soft soil, mechanical, and endurance tests. Results show that the open wheel has lower draw-bar pull (slope climbing) capability in loose soil due to its higher ground pressure and tendency to dig in at high wheel slip. Endurance tests indicate that a double mesh, fully enclosed wheel can be developed to meet DLRV life requirements. There is, however, a 1.0 to 1.8 lb/wheel weight penalty associated with the wheel enclosure. Also the button cleats used as grousers for the closed-type wheels result in local stress concentration and early fatigue failure of the wire mesh. Load deflection tests indicate that the stiffness of the covered wheel increased by up to 50% after soil bin testing, due to increased friction between the fabric and the wire mesh caused by the sand. No change in stiffness was found for the open wheel. The single woven mesh open wheel design with a chevron tread is recommended for continued development

Source record↗

NASA NTRS1953

The Creep of Single Crystals of Aluminum

The creep of single crystals of high-purity aluminum was investigated in the range of temperatures from room temperature to 400 F and at resolved-shear-stress levels of 200, 300, and 400 psi. The tests were designed in an attempt to produce data regarding the relation between the rate of strain and the mechanism of deformation. The creep data are analyzed in terms of shear strain rate and the results are discussed with regard to existing creep theories. Stress-strain curves were determined for the crystals in tinsel and constant-load-rate tests in the same temperature range to supplement the study of plastic deformation by creep with information regarding the part played by crystal orientation, differences in strain markings, and other variables in plastic deformation.

ALUMINUM↗

NASA NTRS1985

Water impact testing of a filament wound case

A lightweight Filament Wound Case (FWC) Solid Rocket Booster (SRB) is being developed by NASA to increase the payload capability of the space shuttle. As with the steel boosters, the current plan is to recover the FWC SRB's after they impact the ocean at 65 to 85 ft/sec. As the boosters enter the ocean (nozzle first) the water moves away from the vehicle creating a cavity, which then collapses on the vehicle, and results in a significant loading event. To understand this loading event, tests were conducted on a quarter scale FWC model to measure cavity collapse pressure distributions, deflected shape and the effects of end conditions and pressure scaling.

Schmidt, A. A.↗

NASA NTRS1984

Fitts' Law? a Test of the Relationship Between Information Load and Movement Precision

The independence of information load (Hick's Law) and movement precision (Fitts' Law) was tested using additive factors methodology. Subjects were required to classify stimuli according to a decision rule with a variable entropy. The stimuli were presented in the center of the CRT screen. In response, subjects had to move a cursor from a starting point near the stimulus to the appropriate target. The precision of the response movement was varied by manipulating the ratio of the radius of the annulus to the width of the target area. The dependent measure was elapsed time between onset of the stimulus and completion of the response movement. Independence of the Hick's Law and Fitts' Law components of the reaction time was tested with an analysis of variance. Presence of an interaction would suggest that a decision stage and a response stage are dependent, and cannot be considered discrete steps in a serial process.

Zalaski, M.↗

NASA NTRS1992

Numerical analysis of the Iosipescu specimen for composite materials

A finite element analysis of the Iosipescu shear tests for unidirectional and cross-ply composites is presented. It is shown that an iterative analysis procedure must be used to model the fixture-specimen kinematics. The correction factors which are needed to compensate for the nonuniformity of stress distribution in calculating shear modulus are shown to be dependent on the material orthotropic ratio and the finite element loading models. Test section strain distributions representative of typical graphite-epoxy specimens are also presented.

Ho, H.↗

NASA NTRS1993

Numerical analysis of the Iosipescu specimen for composite materials

Ho, H.↗

NASA NTRS1974

Spin-Tunnel Investigation of a 1/40-Scale Model of the F-111A Airplane with Store Loadings and with Supplementary Spin-Recovery Devices

An investigation has been made in the Langley spin tunnel to determine the spin and spin-recovery characteristics of the F-111A airplane in the symmetric and asymmetric stores loading conditions. Tests were also made with the model in the clean condition to determine whether the spin-recovery characteristics could be improved by the use of supplementary devices.

Spin-recovery parachute↗

NASA NTRS1974

The circumferentially notched cylindrical bar as a fracture toughness test specimen

The present work reviews the use of the notched cylinder as a screening specimen for use in sorting materials with respect to their relative levels of plane strain fracture toughness. Irwin's work in developing an estimate of stress intensity factors for the circumferentially cracked cylinder is reviewed. Some discrepancies between stress intensity factors determined with fatigue cracked notched cylinders and those determined with plate specimens are discussed. Problems in the technical realization of fatigue cracking a specimen are briefly discussed, and the problem of ensuring low eccentricity of loading when testing notch cylindrical specimens is considered. Finally, specimen size requirements for testing are examined.

Brown, W. F., Jr.↗