Search NASA⌕ Search

SEARCH · Search NASA

Results for “matrix sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

In situ investigation of the deformation behaviors of Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys by high-energy X-ray diffraction

In situ synchrotron-based high-energy X-ray diffraction (HE-XRD) technique was employed to investigate the mechanical behaviors and microstructural evolution of face-centered cubic (FCC) Fe 20 Co 30 Cr 25 Ni 25 and Fe 20 Co 30 Cr 30 Ni 20 high entropy alloys (HEAs) during tensile deformation. Fe 20 Co 30 Cr 30 Ni 20 HEA has a good combination of strength (ultimate tensile strength of 864 ± 35 MPa) and ductility (elongation of 0.627 ± 0.021). The HE-XRD investigation reveals that Fe 20 Co 30 Cr 30 Ni 20 HEA has the transformation-induced plasticity (TRIP) effect, which starts at a critical stress of ~555 MPa. Furthermore, transmission electron microscopy confirmed this deformation-induced new phase is hexagonal-close-packed structured ε-martensite, which follows an orientation relationship of {111} γ //(0001) ε , and (110) γ //[11 2 ¯ 0] ε with the FCC γ matrix. The observation of deformation twins in the deformed samples of the two studied HEAs proves that twinning-induced plasticity (TWIP) effect occurs in both HEAs. The combination of TRIP and TWIP effects lead to the high strength, large ductility and improved strain hardening behavior of Fe 20 Co 30 Cr 30 Ni 20 HEA.

36 MATERIALS SCIENCE↗

Linear response to long wavelength fluctuations using curvature simulations

We study the local response to long wavelength fluctuations in cosmological N -body simulations, focusing on the matter and halo power spectra, halo abundance and non-linear transformations of the density field. The long wavelength mode is implemented using an effective curved cosmology and a mapping of time and distances. The method provides an alternative, more direct, way to measure the isotropic halo biases. Limiting ourselves to the linear case, we find generally good agreement between the biases obtained from the curvature method and the traditional power spectrum method at the level of a few percent. We also study the response of halo counts to changes in the variance of the field and find that the slope of the relation between the responses to density and variance differs from the naïve derivation assuming a universal mass function by approximately 8–20%. This has implications for measurements of the amplitude of local non-Gaussianity using scale dependent bias. We also analyze the halo power spectrum and halo-dark matter cross-spectrum response to long wavelength fluctuations and derive second order halo bias from it, as well as the super-sample variance contribution to the galaxy power spectrum covariance matrix.

79 ASTRONOMY AND ASTROPHYSICS↗

Das ist der HAMMER: consistent new physics interpretations of semileptonic decays

Abstract Precise measurements of $$b\rightarrow c\tau \bar{\nu }$$ b → c τ ν ¯ decays require large resource-intensive Monte Carlo (MC) samples, which incorporate detailed simulations of detector responses and physics backgrounds. Extracted parameters may be highly sensitive to the underlying theoretical models used in the MC generation. Because new physics (NP) can alter decay distributions and acceptances, the standard practice of fitting NP Wilson coefficients to SM-based measurements of the $$R(D^{(*)})$$ R ( D ( ∗ ) ) ratios can be biased. The newly developed software tool enables efficient reweighting of MC samples to arbitrary NP scenarios or to any hadronic matrix elements. We demonstrate how allows avoidance of biases through self-consistent fits directly to the NP Wilson coefficients. We also present example analyses that demonstrate the sizeable biases that can otherwise occur from naive NP interpretations of SM-based measurements. The library is presently interfaced with several existing experimental analysis frameworks and we provide an overview of its structure.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Wetting of Porous α-LiAlO 2 by Molten Carbonate

Cracking of α-LiAlO 2 matrices in molten carbonate fuel cells (MCFC) leads to reduction in the performance. It was demonstrated in this work that the mechanical strength of α-LiAlO2 matrices is improved by heat-treating at 800°C under ambient gas atmosphere. The mechanical strength (2.91MPa) of the heat-treated matrix was enhanced more than 5 fold compared to the non-heat-treated matrix (0.58MPa). The porosity and crystal structure of the α-LiAlO 2 matrices were not changed after the heat-treatment. The wetting behavior and distribution of carbonate in the heat-treated and the non-heat-treated matrix were investigated and compared. Both non-heat-treated and heat-treated α-LiAlO 2 matrices were completely wetted by molten carbonate. The molten carbonate distribution was concentrated right underneath the circular region formed by the molten carbonate drop in the matrix. Non-heat-treated α-LiAlO 2 samples cracked as a result of the complete absorption of molten carbonate, however, the heat-treated α-LiAlO 2 matrices did not crack, presumably due to their enhanced mechanical strength.

36 MATERIALS SCIENCE↗

A graphics processing unit accelerated sparse direct solver and preconditioner with block low rank compression

We present the GPU implementation efforts and challenges of the sparse solver package STRUMPACK. The code is made publicly available on github with a permissive BSD license. STRUMPACK implements an approximate multifrontal solver, a sparse LU factorization which makes use of compression methods to accelerate time to solution and reduce memory usage. Multiple compression schemes based on rank-structured and hierarchical matrix approximations are supported, including hierarchically semi-separable, hierarchically off-diagonal butterfly, and block low rank. Here, in this paper, we present the GPU implementation of the block low rank (BLR) compression method within a multifrontal solver. Our GPU implementation relies on highly optimized vendor libraries such as cuBLAS and cuSOLVER for NVIDIA GPUs, rocBLAS and rocSOLVER for AMD GPUs and the Intel oneAPI Math Kernel Library (oneMKL) for Intel GPUs. Additionally, we rely on external open source libraries such as SLATE (Software for Linear Algebra Targeting Exascale), MAGMA (Matrix Algebra on GPU and Multi-core Architectures), and KBLAS (KAUST BLAS). SLATE is used as a GPU-capable ScaLAPACK replacement. From MAGMA we use variable sized batched dense linear algebra operations such as GEMM, TRSM and LU with partial pivoting. KBLAS provides efficient (batched) low rank matrix compression for NVIDIA GPUs using an adaptive randomized sampling scheme. The resulting sparse solver and preconditioner runs on NVIDIA, AMD and Intel GPUs. Interfaces are available from PETSc, Trilinos and MFEM, or the solver can be used directly in user code. We report results for a range of benchmark applications, using the Perlmutter system from NERSC, Frontier from ORNL, and Aurora from ALCF. For a high frequency wave equation on a regular mesh, using 32 Perlmutter compute nodes, the factorization phase of the exact GPU solver is about 6.5× faster compared to the CPU-only solver. The BLR-enabled GPU solver is about 13.8× faster than the CPU exact solver. For a collection of SuiteSparse matrices, the STRUMPACK exact factorization on a single GPU is on average 1.9× faster than NVIDIA’s cuDSS solver.

97 MATHEMATICS AND COMPUTING↗

Chiral Metamaterials: retrieval of the effective parameters with and without substrate

After the prediction that strong enough optical activity may result in negative refraction and negative reflection, more and more artificial chiral metamaterials were designed and fabricated at difference frequency ranges from microwaves to optical waves. Therefore, a simple and robust method to retrieve the effective constitutive parameters for chiral metamaterials is urgently needed. Here, we analyze the wave propagation in chiral metamaterials and follow the regular retrieval procedure for ordinary metamaterials and apply it in chiral metamaterial slabs. Then based on the transfer matrix technique, the parameter retrieval is extended to treat samples with not only the substrate but also the top layers. After the parameter retrieval procedure, we take two examples to check our method and study how the substrate influences on the thin chiral metamaterials slabs. We find that the substrate may cause the homogeneous slab to be inhomogeneous, i.e. the reflections in forward and backward directions are different. However, the chiral metamaterial where the resonance element is embedded far away from the substrate is insensitive to the substrate.

36 MATERIALS SCIENCE↗

Performance Targets for Perovskite Photovoltaic Research, Development, and Demonstration Programs

On October 15, 2021, the U.S. Department of Energy Solar Energy Technologies Office (SETO) released the Performance Targets for Perovskite Photovoltaic Research, Development, and Demonstration Programs Request for Information (RFI) for public response and comment. The RFI sought feedback from industry, academia, research laboratories, government agencies, and other stakeholders on efficiency, stability and replicability performance targets for perovskite (PVSK) photovoltaic devices that could be utilized to align community efforts, ensure relevance of potential future funding programs, and accelerate technical and commercial development and de-risking of perovskite technologies. The RFI included the following proposed target matrix for power conversion efficiency (PCE), area, stability, and sample sizes, and included questions on relevance, completeness, and challenges.

14 SOLAR ENERGY↗

Monotectic and syntectic alloys experiment MA-044

The flight test furnace run of the monotectic and syntectic alloys experiment was successfully performed during the Apollo Soyuz Test Project mission. All three experiment cartridges were returned intact. A second ground based test was conducted after the mission to provide one g samples with an equivalent thermal history. The examinations of all flight and ground based cartridges and ampoules have been completed. Encouraging results have been obtained in the preliminary analysis of one flight aluminum antimonide sample as compared to ground based and prototype test counterparts. In terms of reduction of the unwanted second phase, the low g sample shows a homogeneity improvement by a factor of 5 to 20. Preliminary examination of one lead zinc flight sample shows a dispersion of lead in the zinc matrix. However, complete homogenization of the material did not occur. A thermal analysis of flight data shows that the average soak temperature for the head zinc ampoules was 20 C lower than planned but 35 C above the published consolute temperature..

Ang, C. Y.↗

Experimental results on plasma interactions with large surfaces at high voltages

Multikilowatt power levels for future payloads can be more efficiently generated using solar arrays operating in the kilovolt range. This implies that large areas of the array at high operating voltages will be exposed to the space plasma environment. The resulting interactions of these high voltage surfaces with space plasma environments can seriously impact the performance of the satellite system. The plasma-surface interaction phenomena were studied in tests performed in two separate vacuum chambers, a 4.6 m diameter by 19.2 long chamber and a 20 m diameter by 27.4 m long chamber. The generated plasma density was approximately 1x10 to the 4th power/cu cm. Ten solar array panels, each with areas of 1400 sq cm were used in the tests. Nine of the solar panels were tested as a composite unit in the form of a 3x3 solar panel matrix. The results from all the tests confirmed small sample tests results: insulators were found to enhance the plasma coupling current for high positive bias and arcing was found to occur at high negative bias.

Grier, N. T.↗

Interferometer Detects Acoustic Emissions in Composites

Embedded single-mode optical fibers sample internal-stress fields directly. Statically loaded composite matrix emits pulsed ultrasonic waves which mechanically modulate embedded fiber and phase-modulate transmitted optical field. Modulation detected by optical interferometry and Fourier optical processing converted to electronic signal proportional to acoustic field amplitude integated along length of fiber embedded in specimen. Technique used for measurements of both high- and low-frequency CW acoustic fields as well as high-frequency transients.

Cantrell, J. H.↗

Composite structural materials

Progress is reported in studies of constituent materials composite materials, generic structural elements, processing science technology, and maintaining long-term structural integrity. Topics discussed include: mechanical properties of high performance carbon fibers; fatigue in composite materials; experimental and theoretical studies of moisture and temperature effects on the mechanical properties of graphite-epoxy laminates and neat resins; numerical investigations of the micromechanics of composite fracture; delamination failures of composite laminates; effect of notch size on composite laminates; improved beam theory for anisotropic materials; variation of resin properties through the thickness of cured samples; numerical analysis composite processing; heat treatment of metal matrix composites, and the RP-1 and RP2 gliders of the sailplane project.

Ansell, G. S.↗

Investigation of the effect of thermal exposure on the mechanical properties of titanium/SiC composites

The objective was to evaluate the influence of thermal exposure, both isothermal and cyclic, on the reaction kinetics, mechanical properties and fracture behavior of Ti-1100 alloy/SiC fiber composites. Previously, it was determined that composites made with TiB2 coated SiC fiber (sigma) reacted at the same rate as SCS-6 fibers. As a result, the thinner surface coating on the Sigma fiber was completely consumed at shorter times than that on the SCS-6. Thermal cycling experiments were conducted on longitudinal and transverse Ti-1100/SCS-6 composites over a temperature range of 150 to 800 C for 500 cycles. The thermal exposures were carried out in air and argon. No appreciable tensile strength degradation was observed for samples cycled in argon, although a strength loss was noted for the samples cycled in air. Fracture surfaces characterization showed brittle matrix failure in regions near the surface and in regions where there was a path for O2 ingress.

Gundel, Douglas B.↗

Chemical studies of H chondrites. III - Regolith evolution of the Fayetteville chondrite parent

Radiochemical neutron concentration analysis was used to determine Ag, Au, Bi, Cd, Co, Cs, Ga, In, Rb, Sb, Se, Te, Tl, and Zn contents in consortium samples of solar gas and track-rich dark matrix. Data obtained confirmed that the matrix is chemically homogeneous. Most dark clasts had similar mean trace element concentrations as the matrix but were compositionally much more heterogeneous. It is concluded that material incorporated with soil and compacted to form the dark portion of Fayetteville included soil-melt, the odd C2M fragment, and dark and light clasts which escaped comminution.

Xiao, Xiaoyue↗

Single-Transducer, Ultrasonic Imaging Method for High-Temperature Structural Materials Eliminates the Effect of Thickness Variation in the Image

NASA Lewis Research Center's Life Prediction Branch, in partnership with Sonix, Inc., and Cleveland State University, recently advanced the development of, refined, and commercialized an advanced nondestructive evaluation (NDE) inspection method entitled the Single Transducer Thickness-Independent Ultrasonic Imaging Method. Selected by R&D Magazine as one of the 100 most technologically significant new products of 1996, the method uses a single transducer to eliminate the superimposing effects of thickness variation in the ultrasonic images of materials. As a result, any variation seen in the image is due solely to microstructural variation. This nondestructive method precisely and accurately characterizes material gradients (pore fraction, density, or chemical) that affect the uniformity of a material's physical performance (mechanical, thermal, or electrical). Advantages of the method over conventional ultrasonic imaging include (1) elimination of machining costs (for precision thickness control) during the quality control stages of material processing and development and (2) elimination of labor costs and subjectivity involved in further image processing and image interpretation. At NASA Lewis, the method has been used primarily for accurate inspections of high temperature structural materials including monolithic ceramics, metal matrix composites, and polymer matrix composites. Data were published this year for platelike samples, and current research is focusing on applying the method to tubular components. The initial publicity regarding the development of the method generated 150 requests for further information from a wide variety of institutions and individuals including the Federal Bureau of Investigation (FBI), Lockheed Martin Corporation, Rockwell International, Hewlett Packard Company, and Procter & Gamble Company. In addition, NASA has been solicited by the 3M Company and Allison Abrasives to use this method to inspect composite materials that are manufactured by these companies.

Roth, Don J.↗

Bayesian Approach to the Joint Inversion of Gravity and Magnetic Data, with Application to the Ismenius Area of Mars

This viewgraph presentation reviews a Bayesian approach to the inversion of gravity and magnetic data with specific application to the Ismenius Area of Mars. Many inverse problems encountered in geophysics and planetary science are well known to be non-unique (i.e. inversion of gravity the density structure of a body). In hopes of reducing the non-uniqueness of solutions, there has been interest in the joint analysis of data. An example is the joint inversion of gravity and magnetic data, with the assumption that the same physical anomalies generate both the observed magnetic and gravitational anomalies. In this talk, we formulate the joint analysis of different types of data in a Bayesian framework and apply the formalism to the inference of the density and remanent magnetization structure for a local region in the Ismenius area of Mars. The Bayesian approach allows prior information or constraints in the solutions to be incorporated in the inversion, with the "best" solutions those whose forward predictions most closely match the data while remaining consistent with assumed constraints. The application of this framework to the inversion of gravity and magnetic data on Mars reveals two typical challenges - the forward predictions of the data have a linear dependence on some of the quantities of interest, and non-linear dependence on others (termed the "linear" and "non-linear" variables, respectively). For observations with Gaussian noise, a Bayesian approach to inversion for "linear" variables reduces to a linear filtering problem, with an explicitly computable "error" matrix. However, for models whose forward predictions have non-linear dependencies, inference is no longer given by such a simple linear problem, and moreover, the uncertainty in the solution is no longer completely specified by a computable "error matrix". It is therefore important to develop methods for sampling from the full Bayesian posterior to provide a complete and statistically consistent picture of model uncertainty, and what has been learned from observations. We will discuss advanced numerical techniques, including Monte Carlo Markov

data analysis↗

Formulation, Casting, and Evaluation of Paraffin-Based Solid Fuels Containing Energetic and Novel Additives for Hybrid Rockets

This investigation studied the inclusion of various additives to paraffin wax for use in a hybrid rocket motor. Some of the paraffin-based fuels were doped with various percentages of LiAlH4 (up to 10%). Addition of LiAlH4 at 10% was found to increase regression rates between 7 - 10% over baseline paraffin through tests in a gaseous oxygen hybrid rocket motor. Mass burn rates for paraffin grains with 10% LiAlH4 were also higher than those of the baseline paraffin. RDX was also cast into a paraffin sample via a novel casting process which involved dissolving RDX into dimethylformamide (DMF) solvent and then drawing a vacuum on the mixture of paraffin and RDX/DMF in order to evaporate out the DMF. It was found that although all DMF was removed, the process was not conducive to generating small RDX particles. The slow boiling generated an inhomogeneous mixture of paraffin and RDX. It is likely that superheating the DMF to cause rapid boiling would likely reduce RDX particle sizes. In addition to paraffin/LiAlH4 grains, multi-walled carbon nanotubes (MWNT) were cast in paraffin for testing in a hybrid rocket motor, and assorted samples containing a range of MWNT percentages in paraffin were imaged using SEM. The fuel samples showed good distribution of MWNT in the paraffin matrix, but the MWNT were often agglomerated, indicating that a change to the sonication and mixing processes were required to achieve better uniformity and debundled MWNT. Fuel grains with MWNT fuel grains had slightly lower regression rate, likely due to the increased thermal conductivity to the fuel subsurface, reducing the burning surface temperature.

Larson, Daniel B.↗