Results for “operational data” — Page 40

NASA NTRS2018

Laboratory Evaluation of Dynamic Routing of Air Traffic in an En Route Arrival Metering Environment

Arrival air traffic operations in the presence of convective weather are subject to uncertainty in aircraft routing and subsequently in flight trajectory predictability. Current management of arrival operations in weather-impacted airspace results in significant flight delay and suspension of arrival metering operations. The Dynamic Routing for Arrivals in Weather (DRAW) concept provides flight route amendment advisories to Traffic Management Coordinators to mitigate the impacts of convective weather on arrival operations. DRAW provides both weather conflict and schedule information for proposed route amendments, allowing air traffic managers to simultaneously evaluate weather avoidance routing and potential schedule and delay impacts. Subject matter experts consisting of retired Traffic Management Coordinators and retired Sector Controllers with arrival metering experience participated in a simulation study of Fort Worth Air Route Traffic Control Center arrival operations. Data were collected for Traffic Management Coordinator and Sector Controller participants over three weeks of simulation activities in October, 2017. Traffic Management Coordinators reported acceptable workload levels, a positive impact on their ability to manage arrival traffic while using DRAW, and initiated weather mitigation reroutes earlier while using DRAW. Sector Controllers also reported acceptable workload levels while using DRAW.

Air Traffic Management↗

NASA NTRS2019

Developing an Aircraft-Based Angular Distribution Model of Solar Reflection from Wildfire Smoke to Aid Satellite-Based Radiative Flux Estimation

This study examines the angular distribution of scattered solar radiation associated with wildfire smoke aerosols observed over boreal forests in Canada during the ARCTAS (Arctic Research of the Composition of the Troposphere from Aircraft and Satellites) campaign. First, it estimates smoke radiative parameters (550 nm optical depth of 3.9 and single scattering albedo of 0.90) using quasi-simultaneous multiangular and multispectral airborne measurements by the Cloud Absorption Radiometer (CAR). Next, the paper estimates the broadband top-of-atmosphere radiances that a satellite instrument such as the Clouds and the Earth’s Radiant Energy System (CERES) could have observed, given the narrowband CAR measurements made from an aircraft circling about a kilometer above the smoke layer. This estimation includes both an atmospheric correction that accounts for the atmosphere above the aircraft and a narrowband-to-broadband conversion. The angular distribution of estimated radiances is found to be substantially different than the angular model used in the operational data processing of CERES observations over the same area. This is because the CERES model is a monthly average model that was constructed using observations taken under smoke-free conditions. Finally, a sensitivity analysis shows that the estimated angular distribution remains accurate for a fairly wide range of smoke and underlying surface parameters. Overall, results from this work suggest that airborne CAR measurements can bring some substantial improvements in the accuracy of satellite-based radiative flux estimates.

Varnai, Tamas↗

NASA NTRS2010

Kepler Instrument Performance: An In-Flight Update

The Kepler Mission is designed to detect the 80 parts per million (ppm) signal from an Earth-Sun equivalent transit. Such precision requires superb instrument stability on time scales up to 2 days and systematic error removal to better than 20 ppm. The sole scientic instrument is the Photometer, a 0.95 m aperture Schmidt telescope that feeds the 94.6 million pixel CCD detector array, which contains both Science and Fine Guidance Sensor (FGS) CCDs. Since Kepler's launch in March 2009, we have been using the commissioning and science operations data to characterize the instrument and monitor its performance. We find that the in-flight detector properties of the focal plane, including bias levels, read noise, gain, linearity, saturation, FGS to Science crosstalk,and video crosstalk between Science CCDs, are essentially unchanged from their pre-launch values. Kepler'sunprecedented sensitivity and stability in space have allowed us to measure both short- and long- term effects from cosmic rays, see interactions of previously known image artifacts with starlight, and uncover several unexpected systematics that affect photometric precision. Based on these results, we expect to attain Kepler's planned photometric precision over 90% of the field of view.

CCD↗

NASA NTRS2020

Machine Learning for Dynamical Modeling of a Flexible Inverted Pendulum System

The inverted pendulum system, a canonical example of an unstable mechanical system, is often used to model the control problems encountered in the flight of rockets in the initial stages of launch, when the airspeed is too small for aerodynamic stability. A system with a flexible pendulum is a variant that more accurately simulates rocket flight nonlinearities (particularly, the flex modes of the rocket). To increase NASA capability of modeling dynamical systems for which closed form solutions are not clear or easily developed, this project aims to provide a machine learning approach that produces a learned dynamical model of the PENNY robot (a rover with a flexible inverted pendulum) from operational data. The developed approach can then be generalized to other complex dynamical systems, including but not limited to rockets and other robotic systems.

M. A. DuPuis↗

NASA NTRSDate not supplied

Miserable Risk Estimation: “Managing” Low-Probability, High-Consequence Risks

As with all bold endeavors, NASA missions must identify and manage their risks. While estimating the consequences of these risks is typically straightforward, it can be challenging to estimate their likelihood. This is especially true for low-probability risks, due both to the lack of operational data and the cognitive biases humans bring to risk estimation. In this talk, I will present both a tongue-in-cheek and “Management Science” approach to estimating low-probability, high-consequence risks. I then summon my Human Factors colleagues to provide NASA mission managers with the gentle guidance needed to avoid common errors in risk assessment

Mary K Kaiser↗

NASA NTRS1994

Automating Testbed Documentation and Database Access Using World Wide Web (WWW) Tools

A method for providing uniform transparent access to disparate distributed information systems was demonstrated. A prototype testing interface was developed to access documentation and information using publicly available hypermedia tools. The prototype gives testers a uniform, platform-independent user interface to on-line documentation, user manuals, and mission-specific test and operations data. Mosaic was the common user interface, and HTML (Hypertext Markup Language) provided hypertext capability.

documentation↗

NASA NTRS2023

An Analysis of Barriers Preventing the Widespread Adoption of Predictive and Prescriptive Maintenance in Aviation

The aviation industry has long recognized the potential benefits of predictive maintenance, a maintenance strategy that leverages sensor and operational data to predict the future degradation of components. Prescriptive maintenance takes this a step further and considers the entire aviation ecosystem to schedule maintenance actions optimally. With the ability to reduce maintenance costs by up to 30%, as reported by the Department of Energy, these maintenance strategies have been identified to be an important investment to reduce a airline costs. However, despite great interest and technological advances in areas such as diagnostics, prognostics, sensing, computation, and machine learning, the adoption of predictive and prescriptive maintenance has not been widely applied in aviation. To shed light on this issue, we conducted an analysis of the barriers preventing or limiting the adoption of predictive and prescriptive maintenance in aviation. Through discussions with subject matter experts across industry, academia, standards bodies, and government, we identified five key challenges: complexity of prediction; validation, safety assurance, and regulatory challenges; cost of adoption; difficulty in quantifying impact and informing decisions; and data availability, quality, and ownership challenges. This study provides a detailed overview of these barriers and areas where stakeholders could invest to overcome them, aiming to support the scaled adoption of predictive and prescriptive maintenance in aviation.

Christopher Teubert↗

NASA NTRSDate not supplied

Strategy for Risk Quantification of Spaceflight Crew Health and Performance Using Dynamic Probabilistic Risk Assessment

At NASA, the Crew Health and Performance (CHP) system represents the span of countermeasures, capabilities, interventions, and tested processes and procedures that in combination work to mitigate the human component of spaceflight mission risk. Across the varying NASA mental models of the CHP system, the different functionalities needed to meet human flight systems standards can be broken down into specific categories (i.e. medical capability, environmental health, behavioral health). These categories can be further broken down into specific subgroups generally associated with the CHP functionalities meant to mitigate or buy down individual human system risks. Taking a similar development approach we seek to leverage dynamic probabilistic risk assessment as a means to quantify and relatively assess the human risk state within the crew health and performance domain. By utilizing existing tools as integrators, we propose a rapid development strategy for incorporating research and operational data that represent the influence of the CHP system functionalities, in order to provide order of magnitudes estimates of the influence on most human system risks outcomes. The model system utilizes a modest cumulative risk approach and that limits the scope to primary paths of influence between the CHP functionalities and human system risks, thus enabling quick prototypes of the integrative effects of CHP functional combinations to solicit valuable feedback from stakeholders and customers on the data, relationship, and structure of the integration.

Drayton Munster↗

NASA NTRSDate not supplied

Trends in Human Spaceflight: Analysis of Observed Propulsion Failure Modes Following NASA’s Artemis I Mission

In 2022, NASA’s Artemis program returned the agency to lunar space, propelled by the Orion European Service Module (ESM). Through rigorous ground test campaigns for Artemis I and II and the collection and transmission of operational data during the Artemis I flight, the Safety and Mission Assurance (S&MA) team created and maintained a robust database of component nonconformances. This study analyzes in-flight and ground processing findings on the Artemis ESM propulsion subsystem to track reliability and safety metrics, as well as comparing the data to that of previous human spaceflight programs, Apollo and Space Shuttle. In drawing a comparison to the Artemis I flight, recommendations can be made for the Artemis II crewed mission to ensure best practices for flight safety, including redundancy and failure tolerance in the system. The results reinforce a need for robust safety standards and caution against the complacency of a single successful test flight.

human spaceflight safety↗

NASA NTRSDate not supplied

Trends in Human Spaceflight: Analysis of Observed Propulsion Failure Modes Following NASA’s Artemis I Mission

In 2022, NASA’s Artemis program returned the agency to lunar space, propelled by the Orion European Service Module (ESM). Through rigorous ground test campaigns for Artemis I and II and the collection and transmission of operational data during the Artemis I flight, the Safety and Mission Assurance (S&MA) team created and maintained a robust database of component nonconformances. This study analyzes in-flight and ground processing findings on the Artemis ESM propulsion subsystem to track reliability and safety metrics, as well as comparing the data to that of previous human spaceflight programs, Apollo and Space Shuttle. In drawing a comparison to the Artemis I flight, recommendations can be made for the Artemis II crewed mission to ensure best practices for flight safety, including redundancy and failure tolerance in the system. The results reinforce a need for robust safety standards and caution against the complacency of a single successful test flight.

human spaceflight safety↗

NASA NTRSDate not supplied

Validation of Cryogenic Propellant Tank Filling using Computational Fluid Dynamics Simulation

Validation of cryogenic propellant tank filling was performed using the Computational Fluid Dynamics (CFD) solver Loci/STREAM-VoF. The validation effort helped identify modeling methodologies that enable NASA to best support its partners in both launch pad and on-orbit filling operations. Data from liquid hydrogen ground tests filled via jet injection were used for the validation effort which include a sensitivity to initial tank wall temperature. Initially hot walls are expected to yield rapid evaporation and possibly boiling. A Volume of Fluid (VoF) methodology was used to capture the gas-liquid interface. Rapid breakup of the liquid jet was observed in simulation results as liquid evaporated and expanded. Inflowing liquid transitioned to a contiguous jet as tank temperatures decreased, gas pressure increased, and saturation conditions at the incoming liquid temperature were approached. The final phase of filling was distinguished by rapid gas pressure rise due to a higher rate of gas volume compression than condensation at the liquid surface. Key physics of propellant tank filling were captured in the computational predictions, and opportunities for added simulation robustness and efficiency in future modeling efforts were identified.

CFM↗

NASA NTRSDate not supplied

Comparison of Orion Flywheel to Commercially Available Flywheel Device

INTRODUCTION: The chosen exercise device for the Orion Multi-purpose Crew Vehicle (MPCV) for Artemis missions is the Orion Flywheel (OFW), which was selected in 2017 from a pool of exercise devices. The Orion Flywheel is to be installed in the MPCV for its first use during the Artemis II mission and will be utilized for subsequent Artemis missions. The OFW provides the capability to perform both resistive and aerobic exercises while taking up a small volume and not requiring power. Aerobic exercise consists of rowing while resistive exercise includes the deadlift, harness squat, and deadlift high pull among others. The efficacy of the OFW as an exercise countermeasure to spaceflight deconditioning has not yet been fully evaluated. A future HRP-funded study using head-down tilt bed rest is planned to evaluate the efficacy of the OFW to mitigate aerobic and muscular deconditioning. The OFW, made by KBR, is a specialized device that poses high costs for purchase and maintenance. The aim of the study is to determine if a commercially available alternative could be used as a backup for the OFW during the bed rest study or as an alternative in other studies. This study seeks to compare the loading profile and mechanics of a commercial flywheel device (kBox Pro) with the three resistance settings of the OFW using a controlled, instrumented setup to validate its acceptability as a backup. METHODS: An experimental setup was designed to simulate human use of the OFW. Flywheel devices can have varied actuated inertial mass and strap length. The inertial mass refers to the flywheel itself or the object that spins as the result of the movement of the strap. The OFW has three gears actuated with a lever, with the low gear used for aerobic rowing and the medium and high gears used for resistance exercises. These gears correspond to increasing flywheel inertia, which corresponds to a certain number and sizes of inertial plates on a commercial flywheel. The kBox Pro has varied sizes of inertial discs that are installed to the external shaft of the device and can be configured to roughly match the inertia seen in the OFW per gear setting. The strap length can be adjusted to allow for different ranges of motion. The experimental setup allows for the simulation of rowing, harness squats, and deadlift high pulls with corresponding exercise strap lengths. All three OFW gears are to be tested, as well as multiple combinations of kBox discs. The setup was created using a system of pulleys and cables to minimize friction loss. The system is actuated through the dropping of a connected mass which, through the pulley system, pulls the strap of the exercise device upwards as if a human was exercising. A string potentiometer and tensile force transducer are used to measure strap displacement and strap force, respectively. The masses dropped are exercise chains that simulate the decrease in force observed throughout a typical exercise. As the chains are lowered to the ground, they begin to spool and therefore are no longer subjecting the exercise device’s strap to their load. This setup was designed to provide realistic loads and protect the OFW from damage, an important precaution because it’s the only available unit for research and ground operations. Data is to be collected across simulated exercises and with different strap lengths, with the same conditions collected on both the OFW and the kBox Pro. RESULTS: Data collection is ongoing for the kBox and the Orion Flywheel. CONCLUSIONS: Study results will inform if the OFW and a kBox Pro device can be deemed mechanically similar. Depending on the results, additional data collection may be required to assess the user experience between the devices. A key result of this study is a mechanical characterization of the OFW device, demonstrating the load and force profile using a repeatable test method. This data will guide next steps on potential kBox Pro modifications needed to produce a comparable exercise experience to the OFW.

Exercise↗

NASA NTRS2026

Thermochemically-Closed Sonic-Flow Inversion for Enthalpy and Temperature in Multispecies Arc-Jet Flows

A thermochemically-closed sonic-flow inversion framework (TSIF) is developed to infer bulk enthalpy and total temperature upstream of a choked nozzle in arc-jet flows. The formulation recasts a pressure-rise total enthalpy quantification technique as an inverse problem in characteristic-velocity c * space using measured mass flow rate, upstream total pressure, gas composition, and nozzle throat geometry as inputs. Unlike calorimetric energy-balance approaches or optical diagnostics, the method relies primarily on routinely measured facility quantities combined with explicit thermochemical closure. Thermochemical states are obtained using NASA’s open-source Chemical Equilibrium with Applications (CEA) code, enabling construction of a chemistry-consistent relation between characteristic velocity, total enthalpy, and total temperature under equilibrium or frozen assumptions. A discharge coefficient is self-calibrated using cold-flow (arc-off) operation data and applied to hot-flow (arc-on) measurements, enabling upstream losses to be accounted for without empirical correlations. The framework is applied to air, N 2 , and CO 2 –N 2 arc-jet flows and demonstrates expected trends for the inferred thermochemical states as function of arc power, specific energy input, mass-flow, heater configuration, and test gas. In the air limit, under equilibrium assumptions, the method recovers the classical high-enthalpy asymptotic correlation of Winovich with a mean residual of 4.4%, demonstrating compatibility with established sonic-flow scaling, while extending applicability to arbitrary multi-species mixtures and non-equilibrium chemistry. The framework provides a mixture-flexible methodology for determining bulk thermochemical states in modern arc-jet environments using routine facility pressure, mass-flow, gas-composition, and nozzle-geometry information together with a cold-flow calibration.

stagnation heat flux↗

NASA NTRS2026

Thermochemically-Closed Sonic-Flow Inversion for Enthalpy and Temperature in Multispecies Arc-Jet Flows

A thermochemically-closed sonic-flow inversion framework (TSIF) is developed to infer bulk enthalpy and total temperature upstream of a choked nozzle in arc-jet flows. The formulation recasts a pressure-rise total enthalpy quantification technique as an inverse problem in characteristic-velocity c * space using measured mass flow rate, upstream total pressure, gas composition, and nozzle throat geometry as inputs. Unlike calorimetric energy-balance approaches or optical diagnostics, the method relies primarily on routinely measured facility quantities combined with explicit thermochemical closure. Thermochemical states are obtained using NASA’s open-source Chemical Equilibrium with Applications (CEA) code, enabling construction of a chemistry-consistent relation between characteristic velocity, total enthalpy, and total temperature under equilibrium or frozen assumptions. A discharge coefficient is self-calibrated using cold-flow (arc-off) operation data and applied to hot-flow (arc-on) measurements, enabling upstream losses to be accounted for without empirical correlations. The framework is applied to air, N 2 , and CO 2 –N 2 arc-jet flows and demonstrates expected trends for the inferred thermochemical states as function of arc power, specific energy input, mass-flow, heater configuration, and test gas. In the air limit, under equilibrium assumptions, the method recovers the classical high-enthalpy asymptotic correlation of Winovich with a mean residual of 4.4%, demonstrating compatibility with established sonic-flow scaling, while extending applicability to arbitrary multi-species mixtures and non-equilibrium chemistry. The framework provides a mixture-flexible methodology for determining bulk thermochemical states in modern arc-jet environments using routine facility pressure, mass-flow, gas-composition, and nozzle-geometry information together with a cold-flow calibration.

inviscid theory↗

DOE OSTI2020

Situation awareness and dynamic ensemble forecasting of abnormal behavior in cyber-physical system

A plurality of monitoring nodes may each generate a time-series of current monitoring node values representing current operation of a cyber-physical system. A feature-based forecasting framework may receive the time-series of and generate a set of current feature vectors using feature discovery techniques. The feature behavior for each monitoring node may be characterized in the form of decision boundaries that separate normal and abnormal space based on operating data of the system. A set of ensemble state-space models may be constructed to represent feature evolution in the time-domain, wherein the forecasted outputs from the set of ensemble state-space models comprise anticipated time evolution of features. The framework may then obtain an overall features forecast through dynamic ensemble averaging and compare the overall features forecast to a threshold to generate an estimate associated with at least one feature vector crossing an associated decision boundary.

Abbaszadeh, Masoud↗

DOE OSTI2021

Optimization of Mitigating System Performance Index to Improve Nuclear Power Plant Safety and Efficiency

MSPI (Mitigation System Performance Index) is one of the risk-informed, plant-specific performance indicators of NRC’s Reactor Oversight Process. MSPI is used by the regulator and nuclear industry to monitor and assess the performance of plant mitigating systems. In this project, a calculation tool has been developed by incorporating the plant operation data, Probabilistic Risk Assessment (PRA) data, and industry baseline values to automate the calculation process of MSPI and the generation of the report. This is the first stage in an effort to optimize the MSPI through advanced artificial intelligence (AI) and machine learning (ML) techniques to improve nuclear power plant safety and efficiency.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Risk-informed autonomous adaptive cyber controllers

Technology related to risk-informed autonomous adaptive cyber controllers is disclosed. In one example of the disclosed technology, a method includes generating probabilities of a cyber-attack occurring along an attack surface of a network. The probabilities can be generated using sensor and operational data of a network as inputs to an attack graph. The risk scores can be determined using a plurality of fault trees and the generated probabilities from the attack graph. The respective risk scores can correspond to respective nodes of an event tree. The event tree and the determined risk scores can be used to determine risk estimates for a plurality of configurations of the network. The risk estimates for the plurality of configurations of the network can be used to reconfigure the network to reduce a risk from the cyber-attack.

Veeramany, Arun↗

DOE OSTI2022

Best Practices for Energy Management Information Systems Metadata Schemas

Fact sheet highlights best practices for metadata schemas and standard naming conventions, which improve the ability of an energy management information system (EMIS) to consistently analyze, visualize, and derive value from operational data. This best practice document is part of a series of fact sheets created to help accelerate the market adoption and use of EMIS in the federal sector. It provides an overview of best practices for using metadata in an EMIS stack, which can significantly reduce the initial time required to deploy an EMIS.

data tags↗