Search NASA⌕ Search

SEARCH · Search NASA

Results for “physical optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

A Low Cost, High Capacity Regenerable Sorbent for Pre-combustion CO 2 Capture

The overall objective of the proposed research is to develop a low cost, high capacity CO 2 sorbent and demonstrate its technical and economic viability for pre-combustion CO 2 capture. The specific objectives supporting our research plan were to optimize the chemical structure and physical properties of the sorbent, scale-up its production using high throughput manufacturing equipment and bulk raw materials and then evaluate its performance, first in bench-scale experiments and then in slipstream tests using actual coal-derived synthesis gas. One of the objectives of the laboratory-scale evaluations was to demonstrate the life and durability of the sorbent for over 10,000 cycles and to assess the impact of contaminants (such as sulfur) on its performance. In the field tests, our objective was to demonstrate the operation of the sorbent using actual coal-derived synthesis gas streams generated by air-blown and oxygen-blown commercial and pilot-scale coal gasifiers (the CO 2 partial pressure in these gas streams is significantly different, which directly impacts the operating conditions hence the performance of the sorbent). To support the field demonstration work, TDA collaborated with Phillips 66 and Southern Company to carry out two separate field tests using actual coal-derived synthesis gas at the Wabash River IGCC Power Plant in Terre Haute, IN and the National Carbon Capture Center (NCCC) in Wilsonville, AL. In collaboration with the University of California, Irvine (UCI), a detailed engineering and economic analysis for the new CO 2 capture system was also proposed to be carried out using Aspen Plus™ simulation software, and estimate its effect on the plant efficiency.

20 FOSSIL-FUELED POWER PLANTS↗

Inverse Methods - Users Manual 5.6

The inverse methods team provides a set of tools for solving inverse problems in structural dynamics and thermal physics, and also sensor placement optimization via Optimal Experimental Design (OED). These methods are used for designing experiments, model calibration, and verfication/validation analysis of weapons systems. This document provides a user's guide to the input for the three apps that are supported for these methods. Details of input specifications, output options, and optimization parameters are included.

42 ENGINEERING↗

Multi-fidelity modeling to predict the rheological properties of fiber suspensions

Unveiling the rheological properties of fiber suspensions is of paramount interest to many industrial applications like biofuel production. The 3D numerical simulations of the suspension of fibers are often computationally expensive and time-consuming. Machine learning methods such as neural networks can simplify the prediction of rheological behavior; however, they require a relatively large training data set. Multi -fidelity models, which combine high-fidelity data from numerical simulations and less expensive lower fidelity data from resources such as simplified physical equations, can lead to optimized predictions. Here, we focus on a neural network with two levels of fidelity, i.e., high and low fidelity networks. To produce high-fidelity data, we perform direct numerical simulations to model the fibers as one-dimensional inextensible slender bodies that obey the Euler- Bernoulli beam equation. The Navier-Stokes equations govern the suspended fluid, and an immersed boundary method is used to couple the fluid and solid motion. The low-fidelity data is produced by using constitutive equations. Noticeable improvements have been observed in the accuracy of predicting the rheological behavior when a multi-fidelity network is used compared to the single-fidelity network.

Boodaghidizaji, Miad↗

Improving the Freight Productivity of a Heavy-Duty, Battery Electric Truck by Intelligent Energy Management

This project aimed to enhance the range and reduce the operating costs of battery electric Class 8 trucks traveling over 250 miles daily. This was achieved through the development and implementation of an intelligent-Energy Management System (i-EMS) that leverages vehicle and operations data, physics-aware machine learning algorithms, and vehicle-to-cloud (V2C) connectivity. The project hypothesized that advanced machine learning algorithms and real-time data analytics could significantly improve the energy efficiency and range of these trucks. Key objectives included developing a physics-aware machine learning algorithm, implementing an i-EMS with V2C connectivity and physics-aware spatial data analytics (PSDA), and validating the system’s effectiveness with fleet partners HEB Companies and Murphy Logistics. Extensive data collection from vehicle operations, including vehicle characteristics, road conditions, and payload, was conducted. A machine learning algorithm was developed to predict energy consumption and enable proactive decision-making. The i-EMS was implemented on two Volvo VNR BEVs, with operators receiving charging and routing recommendations. Charging stations were installed at depot locations in Texas and Minnesota, with an additional on-route charger in Minnesota. Significant findings included a 14% range improvement for Murphy Logistics on a highway-driving eco-route and a 22% range improvement for HEB Companies on a city-driving eco-route. The i-EMS utilized rule-based methods and physics-based algorithms to predict and reduce energy consumption, with real-time monitoring and analysis through V2C connectivity enabling proactive decision-making. The project demonstrated the feasibility and economic viability of battery electric Class 8 trucks for long-haul operations, showcasing the potential of physics-aware machine learning in optimizing energy management. The successful implementation of the i-EMS in real-world scenarios validates its practical application and effectiveness, paving the way for the widespread adoption of battery electric vehicles in the freight transportation industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

FuSED – Users Manual – (V.5.26)

The Fusion of Simulation, Experiment, and Data (FuSED) team provides a set of tools for solving inverse problems in structural dynamics (InverseSD) and thermal physics (InverseAria), a sensor placement optimization tool via Optimal Experimental Design (OED), and a decision boundary tool using SVMs (TRACE). These methods are used for designing experiments, model calibration, and verification/validation analysis of systems. This document provides a user’s guide.

97 MATHEMATICS AND COMPUTING↗

Physical Activity Types and Programs Recommended by Primary Care Providers Treating Adults With Arthritis, DocStyles 2018

Primary care providers (PCPs) can offer counseling to adults with arthritis on physical activity, which can reduce pain and improve physical function, mental health, and numerous other health outcomes. We analyzed cross-sectional 2018 DocStyles data for 1,366 PCPs who reported they always or sometimes recommend physical activity to adults with arthritis. Most PCPs sampled (88.2%) recommended walking, swimming, or cycling; 65.5% did not recommend any evidence-based, arthritis-appropriate physical activity programs recognized by the Centers for Disease Control and Prevention. Opportunities exist for public health awareness campaigns to educate PCPs about evidence-based physical activity programs proven to optimize health for adults with arthritis when more than counseling is needed.

60 APPLIED LIFE SCIENCES↗

Development of a parameter optimization technique for the design of automatic control systems

Parameter optimization techniques for the design of linear automatic control systems that are applicable to both continuous and digital systems are described. The model performance index is used as the optimization criterion because of the physical insight that can be attached to it. The design emphasis is to start with the simplest system configuration that experience indicates would be practical. Design parameters are specified, and a digital computer program is used to select that set of parameter values which minimizes the performance index. The resulting design is examined, and complexity, through the use of more complex information processing or more feedback paths, is added only if performance fails to meet operational specifications. System performance specifications are assumed to be such that the desired step function time response of the system can be inferred.

Whitaker, P. H.↗

Missions to the sun and to the earth

The program outlined in the present paper represents an optimized plan of solar terrestrial physics. It is constrained only in the sense that it involves not more than one new major mission per year for the Solar Terrestrial Division during the 1980-1985 period. However, the flight activity proposed, if accepted by the Agency and by Congress, would involve a growth in the existing Solar Terrestrial budget by more than a factor of 2. Thus, the program may be considered as somewhat optimistic when viewed in the broader context of the NASA goals and budget. The Agency's integrated FY 1980 Five Year Plan will show how many missions proposed will survive this planning process.

Timothy, A. F.↗

Preliminary test results of electrical charged particle generator for application to fog dispersal

A charged particle generator for use in fog dispersal applications was built and preliminary tests were carried out. The parameter used as a measure of performance was the current measured with a needle probe positioned in the charged jet connected to ground through an ammeter. The needle was movable and allowed the current profile throughout the jet to be determined. The measured current is referred to as the current output. The major independent parameters were liquid water injection rate, plenum pressure, and corona voltage. Optimum current output was achieved at the approximate pressure of 30 psig, corona voltage of 5600 volts, and liquid water injection rate of 6 cc/min. The results of the test with the prototype charged particle generator clearly demonstrate that a current on the order of 20 microamperes can be routinely achieved with the system. This measurement of current does not necessarily represent the total issuing from the nozzle current which is expected to be larger. From these results, confidence was established that a charged particle generator which will operate continuously and consistently can be designed, constructed, and operated. Further work is required, however, to better understand the physical mechanisms involved and to optimize the system for fog dispersal application.

Frost, W.↗

MAX '91: An advanced payload for the exploration of high energy processes on the active sun

The results of a NASA science working group established to study a follow-on to the Solar Maximum Mission are given. A complement of instruments is suggested, with the primary objective of studying the physics of energetic processes in cosmic plasmas by observing high-energy phenomena in solar flares. High-quality flare observations will be possible with these instruments during the next peak in solar activity expected to last from 1990 through at least 1995. The primary objective of MAX '91 is to study energetic processes in cosmic plasmas by observing high-energy phenomena in solar flares. These processes, which are of general astrophysical importance, include energy release, particle acceleration, and energy transport. Results from comprehensive observing programs conducted during the last solar cycle have demonstrated the great scientific potential of high-energy emissions for addressing these central physical processes. Consequently, a payload optimized for observations of high-energy solar flare phenomena is suggested for MAX '91. It consists of the following four specific instruments: (1) a Fourier-transform X-ray and gamma-ray imager covering the energy range from a few keV to 1 MeV with arcsecond spatial resolution; (2) a cooled germanium X-ray and gamma-ray spectrometer with keV spectral resolution covering the energy range from 10 keV to 50 MeV; (3) Bragg spectrometers with high spectral resolution at wavelengths between 1 and 9 angstrons; and (4) a soft X-ray, EUV, or UV imaging instrument with arcsecond spatial resolution.

Source record↗

Oxide-dispersion-strengthened turbine blades, volume 1

The objective of Project 4 was to develop a high-temperature, uncooled gas turbine blade using MA6000 alloy. The program objectives were achieved. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to nonoptimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (130 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (180 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAly coating should be applied on top of a thin NiCrAlY coating. Vibration tests, whirlpit tests, and a high-rotor-rig test were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. The results of these tests were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be about twice that of a cast DS MAR-M 247 blade.

Millan, P. P., Jr.↗

Response of joint dominated space structures

An approximate method is developed for estimating the transient response of nonlinear systems in terms of linearized modes of response. Its advantages are that it is computationally more efficient than the time integration method and that it is possible to view the design problem in the more traditional physical terms of modal response. The major drawback of the approximate method is loss of accuracy. It seems that both approximate methods and time integration have their roles in design. Approximate methods provide efficient tools for performing parametric studies and they supply physical insights into how to optimize system performance that are not easily inferred from strictly numerical methods. Time integration provides a method for assessing the accuracy of the approximate solution for key simulations and for fine tuning the final design. In the procedure presented the nonlinear system is approximated by an equivalent linear system in which the system parameters are constant over the range of transient response.

Source record↗

Oxide-dispersion-strengthened turbine blades. Volume 2

The overall objective of Project 4 was to develop and test a high-temperature, uncooled gas turbine blade using MA6000 alloy. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to non-optimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (1300 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (1800 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAlY coating should be applied on top of a thin NiCrAlY coating if hot corrosion is expected. Vibration, whirlpit, and high-rotor-rig tests were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. Test results were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be twice that of a cast DS MAR-M 247 blade.

Millan, P. P., Jr.↗

Comparison of FDMA and CDMA for second generation land-mobile satellite communications

Code Division Multiple Access (CDMA) and Frequency Division Multiple Access (FDMA) (both analog and digital) systems capacities are compared on the basis of identical link availabilities and physical propagation models. Parameters are optimized for a bandwidth limited, multibeam environment. For CDMA, the benefits of voice activated carriers, antenna discrimination, polarization reuse, return link power control and multipath suppression are included in the analysis. For FDMA, the advantages of bandwidth efficient modulation/coding combinations, voice activated carriers, polarization reuse, beam placement, and frequency staggering were taken into account.

Yongacoglu, A.↗

Photoexcited escape probability, optical gain, and noise in quantum well infrared photodetectors

We present a detailed and thorough study of a wide variety of quantum well infrared photodetectors (QWIPs), which were chosen to have large differences in their optical and transport properties. Both n- and p-doped QWIPs, as well as intersubband transitions based on photoexcitation from bound-to-bound, bound-to-quasi-continuum, and bound-to-continuum quantum well states were investigated. The measurements and theoretical analysis included optical absorption, responsivity, dark current, current noise, optical gain, hot carrier mean free path; net quantum efficiency, quantum well escape probability, quantum well escape time, as well as detectivity. These results allow a better understanding of the optical and transport physics and thus a better optimization of the QWIP performance.

Levine, B. F.↗

Design of Materials with Alchemite

Machine learning models that establish the relationships between materials processing and properties can enable inverse design of materials through active learning. Alchemite is a commercial software that can perform inverse materials design on sparse data. Here we evaluate Alchemite’s performance on a dataset of shape memory alloys and a dataset of heat exchangers compared to baseline random forest models. Alchemite had higher accuracy when making predictions on sparse data and was more accurate or nearly as accurate as random forests on complete datasets while also quantifying uncertainty. The software was also used to suggest processing steps and design parameters to optimize properties and performance; however, physical validation of the suggested design parameters was beyond the scope of this work. Several useful design insights were gained about the impact of the design parameters on properties and performance including the importance of dopant choice and amount for shape memory alloys and the importance of height and weight on the thermal resistance of heat exchangers.

Machine learning↗