SEARCH · Search NASA

Results for “responsive material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS2019

Exploration of Atmospheric Entries at Uranus & Neptune with HEEET as Heatshield TPS

One important observation from the recent Ice Giants Study sponsored by NASA was that the predicted and margined thicknesses of HEEET (new NASA TPS technology) were much greater than could be woven with the currently established loom capabilities. Since the cost of a loom upgrade would be substantial, the present work explores the entry trajectory space to determine what combinations of entry parameters would result in HEEET thicknesses that fit within the existing loom infrastructure. Toward this end, the entry trajectory space, parameterized by ballistic coefficient and entry flight path angle, was systematically explored for 45° sphere-cone geometries of 3 different radii 0.2 m, 0.3 m, and 0.4 m which covered the range from Galileo-derived probes considered in the Ice Giants Study, and a follow-on study on the possibility of using a single probe architecture (in terms of size and mass) for various destinations, including Venus, Saturn, Uranus, and Neptune. The entry velocities, latitudes, and azimuths at Uranus and Neptune used in the present work were taken from the Ice Giants Study. For each 3D OF trajectory generated by a NASA Ames in-house code, TRAJ, the material response and thickness were computed using another NASA Ames code, FIAT, along with a margins policy proposed by the HEEET project. In the present work, ballistic coefficients ranging from 200 kg/sqm to 350 kg/sqm were considered along with entry flight path angles ranging from -16° to -36° (primarily to allow deceleration loads to vary between 50 g and 200 g).

Prabhu, Dinesh K.↗

NASA NTRS2019

Recent Advancements in Modeling and Simulation of Entry Systems at NASA

This paper describes recent development of modeling and simulation technologies for entry systems in support of NASA's exploration missions. Mission-tailored research and development in modeling of entry systems occurs across the Agency (e.g., within the Orion and Mars 2020 Programs), however the aim of this paper is to discuss the broad, cross-mission research conducted by NASA's Entry Systems Modeling (ESM) Project, which serves as the Agency's only concerted effort toward advancing entry systems across a range of technical disciplines. Technology development in ESM is organized and prioritized from a system-level perspective, resulting in four broad technical areas of investment: (1) Predictive material modeling, (2) Shock layer kinetics and radiation, (3) Computational and experimental aerosciences, and (4) Guidance, navigation, and control. Investments in thermal protection material modeling are geared toward high-fidelity, predictive models capable of handling complex structures, with an eye toward optimizing design performance and quantifying thermal protection system reliability. New computational tools have been developed to characterize material properties and behavior at the microstructural level, and experimental techniques (molecular beam scattering, micro-computed tomography, among others) have been developed to measure material kinetics, morphology, and other parameters needed to inform and validate detailed simulations. Advancements have also been made in macrostructural simulation capability to enable 3-D system-scale calculations of material response with complex topological features, including differential recession of tile gaps. Research and development in the area of shock layer kinetics has focused on air and CO2-based atmospheres. Capacity and capability of the NASA Ames Electric Arc Shock Tube (EAST) have been expanded in recent years and analysis of resulting data has led to several improvements in kinetic models, while simultaneously reducing uncertainties associated with radiative heat transfer predictions. First-principles calculations of fundamental kinetic, thermodynamic, and transport data, along with state-specific models for non-equilibrium flow regimes, have also yielded new insights and have the potential to vastly improve model fidelity. Aerosciences is a very broad area of interest in entry systems, yet a number of important challenges are being addressed: Coupled fluid-structure simulations of parachute inflation and dynamics; Experimental and computational studies of vehicle dynamics; Multi-phase flow with dust particles to simulate entry environments at Mars during dust storms; Studies of roughness-induced heating augmentation relevant to tiled and woven thermal protection systems; and Advanced numerical methods to optimize computational analyses for desired accuracy versus cost. Guidance and control in the context of entry systems has focused on development of methods for multi-axis control (i.e. pitch and yaw, rather than bank angle alone) of spacecraft during entry and descent. With precision landing requirements driven by Mars human exploration goals, recent efforts have yielded 6-DOF models of multi-axis control with propulsive descent of both inflatable and rigid ellipsled-like architectures.

Barnhardt, Michael D.↗

NASA NTRS2018

Overview of Heatshield for Extreme Entry Environment Technology (HEEET) Project

The objective of the Heatshield for Extreme Entry Environment Technology (HEEET) projects is to mature a 3-D Woven Thermal Protection System (TPS) to Technical Readiness Level (TRL) 6 to support future NASA missions to destinations such as Venus and Saturn. Destinations that have extreme entry environments with heat fluxes up to 5000 watts per square centimeter and pressures up to 5 atmospheres, entry environments that NASA has not flown since Pioneer-Venus and Galileo. The scope of the project is broad and can be split into roughly four areas, Manufacturing/Integration, Structural Testing and Analysis, Thermal Testing and Analysis and Documentation. Manufactruing/Integration covers from raw materials, piece part fabrication to final integration on a 1-meter base diameter 45-degree sphere cone Engineering Test Unit (ETU). A key aspect of the project was to transfer as much of the manufacturing technology to industry in preparation to support future mission infusion. The forming, infusion and machining approaches were transferred to Fiber Materials Inc. and FMI then fabricated the piece parts from which the ETU was manufactured. The base 3D-woven material consists of a dual layer weave with a high density outer layer to manage recession in the system and a lower density, lower thermal conductivity inner layer to manage the heat load. At the start of the project it was understood that due to weaving limitations the heat shield was going to be manufactured from a series of tiles. And it was recognized that the development of a seam solution that met the structural and thermal requirements of the system was going to be the most challenging aspect of the project. It was also recognized that the seam design would drive the final integration approach and therefore the integration of the ETU was kept in-house within NASA. A final seam concept has been successfully developed and implemented on the ETU and will be discussed. The structural testing and analysis covers from characterization of the different layers of the infused material as functions of weave direction and temperature, to sub-component level testing such as 4-pt bend testing at sub-ambient and elevated temperature. ETU test results are used to validate the structural models developed using the element and sub-component level tests. Given the seam has to perform both structurally and aerothermally during entry a novel 4-pt bend test fixture was developed allowing articles to be tested while the front surface is heated with a laser. These tests are intended to establish the system's structural capability during entry. A broad range of aerothermal tests (arcjet tests) are being performed to develop material response models for predicting the required TPS thickness to meet a mission's needs and to evaluate failure modes. These tests establish the capability of the system and assure robustness of the system during entry. The final aspect of the project is to develop a comprehensive Design and Data Book such that a future mission will have the information necessary to adopt the technology. This presentation will provide an overview and status of the project and describe the status of the tehnology maturation level for the inner and outer planet as well as earth entry sample return missions.

Ellerby, Don↗

NASA NTRS2018

Multi-Scale Modeling of Low-Density Carbon-Phenolic Ablators

Protecting a spacecraft during atmospheric entry is one of highest risk factors that needs to be mitigated during design of a space exploration mission. At entry speeds from space, air turns into high-temperature plasma, and spacecraft Thermal Protection Systems (TPS) are needed to protect the vehicle payload. Modern successful material architectures of spacecraft shields use a porous carbon fiber substrate impregnated with phenolic as an ablator material. In the lecture, efforts to build a Predictive Material Modeling framework for porous ablators from micro-scale to macro-scale will be presented. Several numerical methods and techniques will be summarized that use voxelized images to compute geometrical properties of the porous substrate. These computed properties include porosity, specific surface area and tortuosity that are otherwise indirectly measured through experimental techniques. Direct simulation Monte Carlo (DSMC), a particle-based method for approximating the Boltzmann equation, is used to compute the permeability coefficient of the porous substrate based on its digitized representation. The method computes the flow within the microstructure, where the size of the pores may approach the mean-free-path of the flow. Finally, a high-fidelity model implemented in PATO (Porous-material Analysis Toolbox) is discussed, and some examples of ablative material response are presented, including for the first time 3D simulations of the full tiled heat shield for the Mars Science Laboratory (MSL) capsule.

Ablators↗

NASA NTRS2019

Modeling Heatshield Erosion Due to Dust Particle Impacts for a Martian Entry Vehicle

Because planetary missions to Mars take years from initial design to arrival at Mars, and because of the unpredictability of major global dust storms, the de-sign of the thermal protection system (TPS) of a Mars entry vehicle requires an estimation for the potential damage caused by dust particle impacts on the heat-shield. This paper will review previous analytical and experimental approaches to modeling dust particle ero-sion and will compare the legacy models against more modern computational techniques and new dust ero-sion models that will be based on upcoming experi-ments in the German Aerospace Center (DLR) GBK facility. The various models will be compared by incorporating them into the Icarus material response code applied to a representative vehicle entering the Martian atmosphere.

planetary entry↗

NASA NTRS2019

Exploration of Atmospheric Entries at Uranus & Neptune with HEEET as Heatshield TPS

One important observation from the Ice Giants Study was that the predicted and margined thicknesses of HEEET were greater than could be woven with the currently established loom capabilities. Since the cost of a loom upgrade would be substantial, the present work explored the entry trajectory space to determine what combinations of entry parameters would result in HEEET thicknesses that fit within the existing loom infrastructure. Toward this end, the entry trajectory space, parameterized by ballistic coefficient and entry flight path angle, was systematically explored for 45° sphere-cone geometries of 3 different radii – 0.2 m, 0.3 m, and 0.4 m – which covered the range from Galileo-derived probes considered in the Ice Giants Study, and a follow-on study [4] on the possibility of using a single probe architecture (in terms of size and mass) for various destinations, including Venus, Saturn, Uranus, and Neptune. The entry velocities, latitudes, and azimuths at Uranus and Neptune used in the present work were taken from the Ice Giants Study [1]. For each 3DOF trajectory generated by a NASA Ames in-house code, TRAJ [5], the material response and thickness were computed using another NASA Ames code, FIAT [6], along with a margins policy proposed by the HEEET project [7]. In the present work, ballistic coefficients ranging from 200 kg/m2 to 350 kg/m2 were considered along with entry flight path angles ranging from -16° to -36° (primarily to allow deceleration loads to vary between 50 g and 200 g).

HEEET↗

NASA NTRS2019

Laboratory-Based Thermal Shock Investigation of Heat Flux Sensors for the Mars 2020 Backshell

Miller, R. A.↗

NASA NTRS2019

Ballistic Entries for Saturn, Uranus, and Neptune with HEEET TPS

One important observation from the Ice Giants Study was that the predicted and margined thicknesses of HEEET were greater than could be woven with the currently established loom capabilities. Since the cost of a loom upgrade could be substantial and time consuming, the present work explored the entry trajectory space to determine what combinations of entry parameters would result in HEEET thicknesses that fit within the existing loom infrastructure. Toward this end, the entry trajectory space, parameterized by ballistic coefficient and entry flight path angle, was systematically explored for 45° sphere-cone geometries of 3 different radii – 0.2 m, 0.3 m, and 0.4 m – which covered the range from Galileo-derived probes considered in the Ice Giants Study, and a follow-on study on the possibility of using a single probe architecture (in terms of size and mass) for various destinations, including Venus, Saturn, Uranus, and Neptune. The entry velocities, latitudes, and azimuths at Uranus and Neptune used in the present work were taken from the Ice Giants Study. For each 3DOF trajectory generated by a NASA Ames in-house code, TRAJ, the material response and thickness were computed using another NASA Ames code, FIAT, along with a margins policy proposed by the HEEET project. In the present work, ballistic coefficients ranging from 200 kg/sq m to 350 kg/sq m were considered along with entry flight path angles ranging from -16° to -36° (primarily to allow deceleration loads to vary between 50 g and 200 g).

Atmospheric Entry↗

NASA NTRS2019

Laboratory-Based Thermal Shock Investigation of Heat Flux Sensors for the Mars 2020 Backshell

In 2012 during the entry, descent, and landing of the Mars Science Laboratory (MSL), the MSL Entry, Descent, and Landing Instrumentation (MEDLI) sensor suite was collecting in-flight heatshield pressure and temperature data. The data collected by the MEDLI instruments has since been used for reconstruction of vehicle aerodynamics, atmospheric conditions, aerothermal heating, and Thermal Protection System (TPS) performance as well as material response model validation and refinement. The Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite for the Mars 2020 heatshield and backshell is being designed to expand on the measurements and knowledge gained from MEDLI. Similar to MEDLI, MEDLI2 will measure the pressure and temperature of the heatshield. MEDLI2 will additionally measure the temperature, pressure, total heat flux, and radiative heat flux on the backshell.Since the backshell instrumentation is new to MEDLI2, Do No Harm (DNH) testing was conducted on instrumented backshell TPS (SLA-561V) panels. The panels consisted of four pressure port holes, one Mars Entry Atmospheric Data System (MEADS) pressure port plug, one MEDLI2 Integrated Sensor Plug (MISP) thermal plug, and one heat flux sensor. DNH testing was conducted to ensure the performance of the TPS was not degraded due to sensor integration and to characterize any TPS performance changes. The testing consisted of environmental testingâ€” vibration, shock, thermal vacuum (TVAC) cyclingâ€” and bounding aerothermal (arc jet) testing. During arc jet testing, the heat flux sensors embedded in the SLA-561V panels exhibited an unexpected temporary reduction in the heat flux sensor temperature and response. After review of the test results, it was determined that this unexpected response was confined to the two heat flux sensors that experienced the greatest thermal shock condition. This condition consisted of a liquid nitrogen (LN2) bath that induced temperatures of approximately -190Â°C, and then a transition (thermal shock) to an arc jet test at a heat rate of approximately 21 W/cm2. Both heat flux sensors that were exposed to this thermal shock experienced a blister in the thermal coating during the arc jet test.Two heat flux sensor thermal shock test series were performed to investigate the cause of the blistering and subsequent energy release. In these tests, the heat flux sensor was first cold soaked in either a dry ice or LN2 bath to induce temperatures of approximately -78Â°C or -190Â°C, respectively. Then the sensors were thermally shocked using two propane torches with a heat rate of either approximately 8 W/cm2 or 21 W/cm2. The key findings indicated that there is a correlation between thermal shock and the blistering observed in the DNH test series, and that the cause appeared to be rooted in the heat flux sensor epoxy that encapsulates the sensor thermopile.Since the heat flux sensors are required to measure heat fluxes up to 15 W/cm2 during the Mars 2020 entry, a third test series was designed to determine if blistering is an issue at this maximum expected flight heat flux. Results from all three thermal shock test series and a discussion about whether or not blistering of the heat flux sensor thermal coating could be an issue for the Mars 2020 mission will be presented.

Miller, R. A.↗

NASA NTRS2019

Progress Towards Modeling the Mars Science Laboratory PICA-NuSil Heatshield

The data collected by the Mars Science Laboratory (MSL) Entry, Descent and Landing Instrumentation, MEDLI, have become an established reference to assess the performance of engineering models of the Phenolic Impregnated Carbon Ablator (PICA) and to validate hypersonic computational fluid dynamics (CFD) tools for entry systems. MEDLI measurements are also extensively used as validation reference for current developments of high-fidelity material response models for PICA. So large has been the scientific output and impact of MEDLI that a follow-up instrumentation suite MEDLI2 is underway for the upcoming Mars 2020 mission.A feature neglected thus far in the modeling of the MSL heatshield, is the presence of a silicone-based room temperature vulcanizing coating designated NuSil CV-1144-0. NuSil was used to coat the entire MSL heatshield, including the MEDLI plugs, to mitigate the spread of phenolic dust from PICA, and limit contamination during clean room operations. NuSil CV-1144-0 is a space grade siloxane copolymer, designed as an oxygen protection barrier for extreme low temperature environment.Assessments conducted during MSL development demonstrated that the presence of NuSil had no adverse effect on the performance of PICA. However, evidence from ground testing of PICA-NuSil (PICA-N) models in the HyMETS arc-jet test facility suggests that the silicone changes the high temperature response of PICA. It is therefore critical to assess the importance of modeling the coating in ongoing code validation efforts.

Bessire, Brody K.↗

NASA NTRS2019

Overview of Heatshield for Extreme Entry Environment Technology (HEEET)

The objective of the Heatshield for Extreme Entry Environment Technology (HEEET) projects is to mature a 3-D Woven Thermal Protection System (TPS) to Technical Readiness Level (TRL) 6 to support future NASA missions to destinations such as Venus and Saturn. Destinations that have extreme entry environments with heat fluxes > 3500 W/cm2 and pressures up to 5 atmospheres, entry environments that NASA has not flown since Pioneer-Venus and Galileo. The scope of the project is broad and can be split into roughly four areas, Manufacturing/Integration, Structural Testing and Analysis, Thermal Testing and Analysis and Documentation. Manufacturing/Integration covers from raw materials, piece part fabrication to final integration on a 1-meter base diameter 45-degree sphere cone Engineering Test Unit (ETU). A key aspect of the project was to transfer as much of the manufacturing technology to industry in preparation to support future mission infusion. The forming, infusion and machining approaches were transferred to Fiber Materials Inc. and FMI then fabricated the piece parts from which the ETU was manufactured. The base 3D-woven material consists of a dual layer weave with a high-density outer layer to manage recession in the system and a lower density, lower thermal conductivity inner layer to manage the heat load. At the start of the project it was understood that due to weaving limitations the heat shield was going to be manufactured from a series of tiles. And it was recognized that the development of a seam solution that met the structural and thermal requirements of the system was going to be the most challenging aspect of the project. It was also recognized that the seam design would drive the final integration approach and therefore the integration of the ETU was kept in-house within NASA. A final seam concept has been successfully developed and implemented on the ETU. The structural testing and analysis covers from characterization of the different layers of the infused material as functions of weave direction and temperature to sub-component level testing such as 4pt bend testing at sub-ambient and elevated temperature and culminates in testing of the ETU results from which will validate the structural models developed using the element and sub-component level tests. Given the seam has to perform both structurally and aerothermally during entry a novel 4pt bend test fixture was developed allowing articles to be tested while the front surface is heated with a laser. These tests are being utilized to establish the systems structural capability during entry.A broad range of aerothermal tests (arcjet tests) were performed to develop material response models for predicting the required TPS thickness to meet a missions needs and to evaluate failure modes and establish the capability of the system. The final aspect of the project is to develop a comprehensive Design and Data Book such that a future mission will have the information necessary to adopt the technology. This presentation will provide an overview for each of these areas and argue that HEEET has successfully achieved TRL 6.

HEEET↗

NASA NTRS2019

Effect of Out-Gassing on the Onset of Hypersonic Boundary Layer Transition

Prediction and control of the onset of transition and the associated variation in aerothermodynamic parameters in high-speed flows is key to optimize the performance and design of Thermal Protection Systems (TPS) of next-generation aerospace vehicles [1]. Boundary Layer Transition (BLT) characteristics can influence the surface heating budget determining the TPS thickness and consequently its weight penalty. Ablative heatshields are designed to alleviate the high heat flux at the surface through pyrolysis of their polymeric matrix and subsequent fiber ablation [2]. Pyrolysis leads to out-gassing and non-uniform ablation lead to surface roughness, both of which are known to influence the transition process. An ablator impacts BLT through three main routes: gas injecting into the boundary layer from the wall, changing the surface heat transfer due to wall-flow chemical reactions, and modifying surface roughness [3]. In preparation to Mars 2020 mission post-flight analysis, the predictive transition capability has been initiated toward hard-coupling porous material response analysis and aerothermal environment calculation.

Karimi, Mona↗

NASA NTRSDate not supplied

Recent Advances in Discrete Crack Modeling Applied to Laminated Composites with Emphasis on: Floating Node Method, VCCT and Cohesive Zone Modeling

The present talk will provide an overview of the work performed during the Advanced Composites Project (ACP) on the development, and verification and validation of the Floating Node Method (FNM) as well as the Virtual Crack Closure Technique (VCCT) and cohesive zone modeling (CZM). The FNM is a finite element-based technique to represent crack networks. The complex nature of matrix crack-delamination interactions observed in unidirectional (UD) tape laminates suggests that a methodology such as the FNM method may be required to be able to accurately simulate damage progression in these laminates. Simulating crack onset and growth within the context of the FNM relies on techniques such as VCCT and CZM. The talk is organized to provide, via select examples, an overview of the breadth of the Verification & Validation (V&V) exercises performed during the ACP, and how these challenged the state-of-the art and guided further developments in discrete crack modeling, while helping to establish confidence in the progress made and map the challenges ahead. The performance of the VCCT and CZM individually, and in combination with the FNM can be assessed through verification exercises. These exercises typically consist of a comparison of simulation results to known numerical or analytical solutions. Verification is key to identify implementation issues and limitations that, otherwise, may remain undetected and cloud any subsequent validation efforts. Indeed, a subset of these numerical exercises led to further developments of the VCCT and the FNM method as will be illustrated. Before embarking on the subsequent validation of the framework, it is critical to have adequate characterization data. However, the testing campaign conducted revealed material responses that challenged the state-of-the-art and required further developments. The developments in CZM technology associated with the modeling of the responses of hybrid interfaces (fabric/UD) will be given as an example. Finally, the talk will conclude with a summary of the validation exercises performed under quasi-static and fatigue loadings, highlighting some of the key achievements, outstanding challenges and lessons learned.

finite elements↗

NASA NTRSDate not supplied

High-Fidelity Simulations of HyMETS Arc-Jet Flows for PICA-N Modeling

Arc-jet testing is a fundamental tool in the screening of thermal protection systems under atmospheric entry conditions. In this work, high-fidelity computational fluid dynamics simulations coupled with machine learning methods for the Hypersonic Materials Environmental Test System arc-jet facility have been carried out. This effort improves the MEDLI-2 data reconstruction fidelity by understanding the impact of the NuSil coating over the PICA thermocouple plugs. Thermochemical non-equilibrium models are employed to simulate the flows inside the arc-jet nozzle and chamber and machine learning techniques are used to calibrate the arc-jet inflow conditions. The material response is simulated with the recession and in-depth numerical results compared to experimental measurements.

STMD↗

NASA NTRS2001

Characterization of the electromechanical properties of IPMC

An experimental setup was developed for data acquisition from IPMC strips subjected to various tip mass levels and in parallel an analytical model was developed to predict ther material response.

IPMC↗

NASA NTRSDate not supplied

Unified Material-Environment Interaction Model for Binary UHTC Composites

A new model for the surface chemistry of zirconium and hafnium diborides containing silicon-carbide when exposed to high temperature conditions in air is formulated. Oxidation dynamics are simplified by considering the diffusion-limited equilibrium regime within the material at elevated temperatures. This model is first assessed against experimental mass-gain data taken from UHTC samples heated to high temperature in an oxygen environment. Then, further evaluations of the new model are conducted using hypersonic CFD simulations to analyze conditions experienced by HfB2-SiC in arc jet experiments conducted at NASA Ames Research Center. Measurements of stagnation point heat transfer and pressure are then used to calibrate the simulations. Results of coupled CFD-material response simulations are then compared to the surface temperatures measured during the Ames arc jet test. Results support the use of the proposed model while highlighting the need for improved gas-phase data on the additional constituents considered.

ultra high temperature ceramic↗

NASA NTRSDate not supplied

Sensitivity Study of Dust-Induced Surface Erosion during Martian Planetary Entry

Large, global dust storms that periodically form in the Martian atmosphere pose a threat to NASA missions due to a lack of understanding of how they will affect the heat loading and mass loss of the entry vehicle’s thermal protection system (TPS). Previous studies have laid out viable methodologies for estimating the amount of surface recession from a significant dust storm, but rely on underlying modeling assumptions that are difficult to validate. The current work utilizes the DUST library, which is a Lagrangian particle solver under development at NASA Ames Research Center. DUST includes variable-fidelity fluid-particle coupling and has been tested for a wide range of problem types. The DUST library is used in conjunction with the US3D Naiver-Stokes solver. Using these tools, a sensitivity study is performed to determine the influence of the underlying dust modeling (drag coefficient, Nusselt number, and size distribution) on the surface erosion through a hypersonic Martian entry trajectory. The surface erosion was found to be insensitive to the drag and heating models, but was affected significantly by the size distributions parameters. The total recession was comparable to the thermochemical ablation predicted by material response codes, but the lack of a particle erosion model for PICA limits the predictive capability of the current work.

Thermal Protection Systems↗

NASA NTRS2021

Recent Advancements in Modeling and Simulation of Entry Systems at NASA

This paper describes recent development of modeling and simulation technologies for entry systems in support of NASA’s exploration missions. Mission-tailored research and development in modeling of entry systems occurs across the Agency (e.g., within the Orion and Mars 2020 Programs), however the aim of this paper is to discuss the broad, cross-mission research conducted by NASA’s Entry Systems Modeling (ESM) Project, which serves as the Agency’s only concerted effort toward advancing entry systems across a range of technical disciplines. Technology development in ESM is organized and prioritized from a system-level perspective, resulting in four broad technical areas of investment: (1) Predictive material modeling, (2) Shock layer kinetics and radiation, (3) Computational and experimental aerosciences, and (4) Guidance, navigation, and control. Investments in thermal protection material modeling are geared toward high-fidelity, predictive models capable of handling complex structures, with an eye toward optimizing design performance and quantifying thermal protection system reliability. New computational tools have been developed to characterize material properties and behavior at the microstructural level, and experimental techniques (molecular beam scattering, micro-computed tomography, among others) have been developed to measure material kinetics, morphology, and other parameters needed to inform and validate detailed simulations. Advancements have also been made in macrostructural simulation capability to enable 3-D system-scale calculations of material response with complex topological features, including differential recession of tile gaps. Research and development in the area of shock layer kinetics has focused on air and CO2-based atmospheres. Capacity and capability of the NASA Ames Electric Arc Shock Tube (EAST) have been expanded in recent years and analysis of resulting data has led to several improvements in kinetic models, while simultaneously reducing uncertainties associated with radiative heat transfer predictions. First-principles calculations of fundamental kinetic, thermodynamic, and transport data, along with state-specificmodels for non-equilibrium flow regimes, have also yielded new insights and have the potential to vastly improve model fidelity. Aerosciences is a very broad area of interest in entry systems, yet a number of important challenges are being addressed: Coupled fluid-structure simulations of parachute inflation and dynamics; Experimental and computational studies of vehicle dynamics; Multi-phase flow with dust particles to simulate entry environments at Mars during dust storms; Studies of roughness-induced heating augmentation relevant to tiled and woven thermal protection systems; and Advanced numerical methods to optimize computational analyses for desired accuracy versus cost. Guidance and control in the context of entry systems has focused on development of methods for multi-axis control (i.e. pitch and yaw, rather than bank angle alone) of spacecraft during entry and descent. With precision landing requirements driven by Mars human exploration goals, recent efforts have yielded 6-DOF models of multi-axis control with propulsive descent of both inflatable and rigid ellipsled-like architectures. Results for both configurations have demonstrated the ability to land within the 50-meter precision requirement demanded by Mars human exploration missions, while also reducing propellant requirements by enabling more efficient control through entry and descent. Ongoing research in GN&C is developing mechanical specifications for the systems and establishing engineering feasibility.

aerothermodynamics↗