SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solar cell modules with welded and soldered interconnections were constructed using a flexible substrate material. These modules were thermally cycled between approx. 80 deg C at rates 100 cycles/day to demonstrate survivability under simulated low Earth orbit (LEO) temperature conditions. The modules, cycled in an inert atmosphere, show durability for 36,000 cycles.
The development history of the data acquisition and data analysis software is discussed. The software development occurred between 1978 and 1984 in support of solar energy module testing at the Jet Propulsion Laboratory's Parabolic Dish Test Site, located within Edwards Test Station. The development went through incremental stages, starting with a simple single-user BASIC set of programs, and progressing to the relative complex multi-user FORTRAN system that was used until the termination of the project. Additional software in support of testing is discussed including software in support of a meteorological subsystem and the Test Bed Concentrator Control Console interface. Conclusions and recommendations for further development are discussed.
The Solar Mesosphere Explorer has been in operation since October 6, 1981. In addition to making measurements of ozone and other trace constituents of the earth's atmosphere the observatory includes a small spectrometer to make daily measurements of the solar ultraviolet irradiance in the spectral range 115 to 305 nm. The solar spectra are obtained with 0.75 nm spectral resolution. Examination of the data show a strong signature of the 27-day solar rotation displaying a time varying modulation of incoming solar radiation exceeding + or - 15 percent near Lyman-alpha, decreasing to a few percent at 200 nm, and less than one percent near 300 nm. Long term trends in the data, due both to changes in the instrument response and to true long term solar variations, are removed in order to obtain quantitative measure of the intermediate term variation with time periods of a few days to weeks.
The multipurpose, manned, permanent space station will be our next step toward utilization of space. A multikilowatt electrical power system will be critical to its success. The power systems for the space station manned core and platforms that have been selected in definition studies are described. The system selected for the platforms uses silicon arrays and Ni-H2 batteries. The power system for the manned core is a hybrid employing arrays and batteries identical to those on the platform along with solar dynamic modules using either Brayton or organic Rankine engines. The power system requirements, candidate technologies, and configurations that were considered, and the basis for selection, are discussed.
The different types of cosmic ray particles and their role in the heliosphere are briefly described. The rates of various energetic particles were examined as a function of time and used to derive various differential energy gradients. The Pioneer and Voyager cosmic ray observations throughout the heliosphere are indeed giving a perspective on the three-dimensional character and size of the heliosphere. Most clearly the observations are emphasizing the role that transient variations in the outer heliosphere, and most likely the heliospheric boundary shock, play in the 11 year solar cycle modulation of cosmic rays.
Presented is structural dynamics modeling of two multibody space structural configurations. The first configuration is a generic space station model of a cylindrical habitation module, two solar array panels, radiator panel, and central connecting tube. The second is a 15-m hoop-column antenna. Discussed is the special joint elimination sequence used for these large finite element models, so that eigenvalues could be extracted. The generic space station model aided test configuration design and analysis/test data correlation. The model consisted of six finite element models, one of each substructure and one of all substructures as a system. Static analysis and tests at the substructure level fine-tuned the finite element models. The 15-m hoop-column antenna is a truss column and structural ring interconnected with tension stabilizing cables. To the cables, pretensioned mesh membrane elements were attached to form four parabolic shaped antennae, one per quadrant. Imposing thermal preloads in the cables and mesh elements produced pretension in the finite element model. Thermal preload variation in the 96 control cables was adjusted to maintain antenna shape within the required tolerance and to give pointing accuracy.
The cosmic ray radial and latitudinal gradients during the 1981-1984 decreasing phase of sunspot cycle 21 are investigated based on data from Voyagers 1 and 2, with a detector threshold of not less than 70 MeV/nuc, and IMP-8, with a detector threshold of not less than 35 MeV/nuc. During the interval, the heliolongitudinal separation between the Voyager spacecraft changed from about 4 to 26 deg, and comparison of the 26-day means of the cosmic ray intensities obtained show that the data is consistent on the average with a long-term zero latitudinal gradient. Comparison at 1 AU of Voyager and IMP-8 data illustrate that the radial gradient decreased over this period at the rate of about 0.4 percent per AU per year, reaching a value of about 2.0 percent/AU between 16 and 22 AU, and a value of about 0.6 percent/AU between 16 and 22 AU, a pattern which would locate both Voyagers during 1977 outside the principal cosmic ray modulation at solar minimum within 22 AU.
The power systems for the Space Station manned core and platforms that have been selected in definition studies are described in this paper. The selected system for the platforms uses silicon arrays and Ni-H2 batteries. The power system for the manned core is a hybrid employing arrays and batteries identical to those on the platform along with solar dynamic modules using either Brayton or organic Rankine engines. The power system requirements, candidate technologies, and configurations that were considered, and the basis for selection, are discussed.
Attention is given to spatial dependences exhibited by spacecraft measurements obtained between 1 and 30 AU, together with temporal variations occurring between solar activity cycle maxima and minima. At 1-3 AU radial distances, shocks develop in association with the corotating solar wind streams characterizing solar minimum and accelerate solar wind evolution with distance while heating the solar wind and generating waves and turbulence. At solar maximum, shocks are observed more frequently at 1 AU but still in association with transient solar events; acceleration leading to energetic storm particles is observed both within and beyond 1 AU. The superimposed effect of large numbers of intense shocks may be responsible for the solar cycle modulation of galactic cosmic rays.
Loss mechanisms which come into play when solar cell modules are mounted in arrays are identified. Losses can occur either from a reduction in the array electrical performance or with nonoptimal extraction of power from the array. Electrical performance degradation is caused by electrical mismatch, transmission losses from cell surface soiling and steep angle of reflectance, and electrical losses from field wiring resistance and the voltage drop across blocking diodes. The second type of loss, concerned with the operating points of the array, can involve nonoptimal load impedance and limiting the operating envelope of the array to specific ranges of voltage and current. Each of the loss mechanisms are discussed and average energy losses expected from soiling, steep reflectance angles and circuit losses are calculated.
The reference configuration of NASA's Space Station includes a large truss structure to support the various modules and solar arrays. This truss structure will be constructed from tubular members approximately 2 in. in diameter and up to 23 ft in length. The important design considerations for this structure are light weight, high stiffness, dimensional stability, and long-term durability. Continuous graphite fiber reinforced polymer matrix composite materials can meet the structural requirements, and are leading candidates for the tubular truss members. However, there are concerns regarding the durability of composites during the long-term exposure to atomic oxygen and thermal cycling that will be encountered during the Space Station service life. This paper discusses space environmental factors and their effect on composite materials, and provides estimates of the changes in mechanical and thermal properties of composites exposed to long-term Space Station conditions. The effect of low velocity impact and handling damage on composite tube properties is also discussed.
More than 20 real periodicities ranging from 20 days to 2 years modulate the solar irradiance data accumulated since November 1978 by Nimbus 7. Many are quite strong during the first three years (solar maximum) and weak after that. There is a high correspondence between periods in irradiance and 28 periods predicted from the rotation and beating of global solar oscillations (r-modes and g-modes). Angular states l = 1, 2, and 3 are detected as well as some unresolved r-mode power at higher l. The prominence of beat periods implies a nonlinear system whose effective nonlinear power was measured to be about 2. This analysis constitutes a detection of r-modes in the sun, and determines from them a mean sidereal rotation rate for the convective envelope of 459 + or - 4 nHz which converts to a period of 25.2 days (27.1d, synodic).
This paper describes the testing and evaluation used to characterize the mechanisms of electrochemical corrosion of photovoltaic modules - encapsulated solar cells. Accelerated exposure testing was performed on a sample matrix of cell/encapsulant combinations, and microanalytical failure analysis was performed on selected samples to confirm the correlation between the accelerated test data and the life prediction model. A quantitative correlation between field exposure time and exposure time in the accelerated multistress tests was obtained based upon the observation that equal quantities of interelectrode charge transfer resulted in equivalent degrees of electrochemical charge.
Performance data for the NASA Lewis Research Center indium phosphide n+p homojunction solar cell module on the LIPS 3 Flight Experiment is presented. The objective of the experiment is to measure the performance of InP cells in the natural radiation environment of the 1100 km altitude, 60+ deg inclination orbit. Analysis of flight data indicates that the performance of the four cells throughout the first year is near expected values. No degradation in short-circuit current was seen, as was expected from radiation tolerance studies of similar cells. Details of the cell structure and flight module design are discussed. The results of the temperature dependency and radiation tolerance studies necessary for normalization and analysis of the data are included.
The flight performance of NASA Lewis Research Center's indium phosphide homojunction solar cell module on the LIPS 3 satellite is presented. A module of four n+p cells was fabricated and has been on-orbit on the LIPS 3 spacecraft since 1987. The experimental objective is the measurement of InP cell performance in the natural radiation environment of the 1100 kilometer altitude, 60 deg inclination, circular orbit. Flight data from the first year is near expected values, with no degradation in short-circuit current. The temperature dependence of current-voltage parameters is included along with the laboratory radiation tolerance studies necessary for normalization and analysis of the data. Details of the cell structure and flight module design are also discussed.
Performance data for the NASA Lewis Research Center indium phosphide n+p homojunction solar cell module on the LIPS 3 flight experiment is presented. The objective of the experiment is to measure the performance of InP cells in the natural radiation environment of the 1100 km altitude, 60+ deg inclination orbit. Analysis of flight data indicates that the performance of the four cells throughout the first year is near expected values. No degradation in short-circuit current was seen, as was expected from radiation tolerance studies of similar cells. Details of the cell structure and flight module design are discussed. The results of the temperature dependency and radiation tolerance studies necessary for normalization and analysis of the data are included.
The 1990 solar cell calibration balloon flight consisted of two flights, one on July 20, 1990 and the other on September 6, 1990. A malfunction occurred during the first flight, which resulted in a complete loss of data and a free fall of the payload from 120,000 ft. After the tracker was rebuilt, and several solar cell modules were replaced, the payload was reflown. The September flight was successful and met all the objectives of the program. Forty-six modules were carried to an altitude of 118,000 ft (36.0 km). Data telemetered from the modules was corrected to 28 C and to 1 a.u. The calibrated cells have been returned to the participants and can now be used as reference standards in simulator testing of cells and arrays.
NASA created a program called In-STEP (in-space technology experiments program) to give the aerospace community an opportunity to validate advanced technologies in space. In-STEP has funded feasibility studies for the following experiments in the power technology arena: a microsphere insulation investigation, a utilized regenerative fuel cell experiment, an inflatable solar collector experiment, a moving belt radiator experiment, and a liquid drop radiator experiment. The following experiments are currently in the experiment definition phase: an integrated two-phase thermal experiment, an electrolysis performance experiment, and a sodium sulfur battery experiment. Three In-STEP experiments are entering the hardware fabrication phase: thermal energy storage technology, solar array module plasma interaction, and heat pipe performance experiments. Each of these experiments is described, with an emphasis on the benefits of technology validation.