Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Cracking behavior and microstructure of austenitic stainless steels and alloy 690 irradiated in BOR-60 reactor, phase I.

Cracking behavior of stainless steels specimens irradiated in the BOR-60 at about 320 C is studied. The primary objective of this research is to improve the mechanistic understanding of irradiation-assisted stress corrosion cracking (IASCC) of core internal components under conditions relevant to pressurized water reactors. The current report covers several baseline tests in air, a comparison study in high-dissolved-oxygen environment, and TEM characterization of irradiation defect structure. Slow strain rate tensile (SSRT) tests were conducted in air and in high-dissolved-oxygen (DO) water with selected 5- and 10-dpa specimens. The results in high-DO water were compared with those from earlier tests with identical materials irradiated in the Halden reactor to a similar dose. The SSRT tests produced similar results among different materials irradiated in the Halden and BOR-60 reactors. However, the post-irradiation strength for the BOR-60 specimens was consistently lower than that of the corresponding Halden specimens. The elongation of the BOR-60 specimens was also greater than that of their Halden specimens. Intergranular cracking in high-DO water was consistent for most of the tested materials in the Halden and BOR-60 irradiations. Nonetheless, the BOR-60 irradiation was somewhat less effective in stimulating IG fracture among the tested materials. Microstructural characterization was also carried out using transmission electron microscopy on selected BOR-60 specimens irradiated to {approx}25 dpa. No voids were observed in irradiated austenitic stainless steels and cast stainless steels, while a few voids were found in base and grain-boundary-engineered Alloy 690. All the irradiated microstructures were dominated by a high density of Frank loops, which varied in mean size and density for different alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Selenium Migration and Local Structures in Cu‐Doped CdSeTe Solar Cells after Aging

Selenium grading plays a critical role in state-of-the-art Cadmium Telluride photovoltaic cells by enhancing long-wavelength absorption and extending minority carrier lifetimes —key to enabling the current performance record of 23.08%. However, very little is understood about selenium motion. In this study, a comprehensive, multimodal, and multiscale approach is employed to investigate Se migration and local structural changes in copper (Cu)-doped CdSeTe solar cells subjected to accelerated stress. X-ray fluorescence (XRF) microscopy shows unexpected levels of Se diffusion after 500 h under heat (75°C) and light (0.8 suns, 80 mW/cm 2 ), suggesting the coexistence of fast and slow diffusion channels even at low temperatures, with unexpectedly low activation energies (<0.85 eV). X-ray Absorption Near Edge Structure (XANES) analysis indicates a preferential migration of Se atoms to anionic lattice sites and a reduction in Se-Cl co-passivation at Te-terminated dislocation cores. Furthermore, these findings point to a reconfiguration of Se local environments and highlight the potential role of extended structural defects in enabling Se transport at low temperatures. Additionally, XANES results suggest that the presence of metallic Cu across the absorber layer may contribute to back-contact degradation and reduced hole density in both fresh and aged devices.

14 SOLAR ENERGY↗

Lattice Softening Significantly Reduces Thermal Conductivity and Leads to High Thermoelectric Efficiency

The influence of micro/nanostructure on thermal conductivity is a topic of great scientific interest, particularly to thermoelectrics. The current understanding is that structural defects decrease thermal conductivity through phonon scattering where the phonon dispersion and speed of sound are assumed to remain constant. Experimental work on a PbTe model system is presented, which show that the speed of sound linearly decreases with increased internal strain. This softening of the materials lattice completely accounts for the reduction in lattice thermal conductivity, without the introduction of additional phonon scattering mechanisms. Additionally, it is shown that a major contribution to the improvement in the thermoelectric figure of merit (zT > 2) of high-efficiency Na-doped PbTe can be attributed to lattice softening. While inhomogeneous internal strain fields are known to introduce phonon scattering centers, this study demonstrates that internal strain can modify phonon propagation speed as well. This introduces new avenues to control lattice thermal conductivity, beyond phonon scattering. In practice, many engineering materials will exhibit both softening and scattering effects, as is shown in silicon. Here, we shine new light on studies of thermal conductivity in fields of energy materials, microelectronics, and nanoscale heat transfer.

36 MATERIALS SCIENCE↗

Bulk and Short-Circuit Anion Diffusion in Epitaxial Fe 2 O 3 Films Quantified Using Buried Isotopic Tracer Layers

Self-diffusion is a fundamental physical process that, in solid materials, is intimately correlated with both microstructure and functional properties. In this work, a universal approach is presented to precisely characterize self-diffusion in ionic solids by isotopically enriching anions and/or cations at specific locations within an epitaxial film stack, and characterize their redistribution at high spatial resolution with atom probe tomography. Nanoscale anion diffusivity is quantified in epitaxial α-Fe 2 O 3 thin films deposited by molecular beam epitaxy with a thin (10 nm) buried layer highly enriched in 18 O. The isotopic sensitivity of the atom probe allows precise measurement of 18 O distribution across the sharp interfaces between this layer and the surrounding Fe 2 O 3 after annealing. Short-circuit anion diffusion through 1D and 2D structural defects in Fe 2 O 3 are also directly visualized in 3D. This versatile approach to study precisely tailored thin film samples at high spatial and mass fidelity will facilitate a deeper understanding of atomic-scale diffusion phenomena.

36 MATERIALS SCIENCE↗

Interfacial Exchange Phenomena Driven by Ferromagnetic Domains

Abstract Interfacial proximity effects in antiferromagnetic/ferromagnetic (AFM/FM) bilayers control the exchange‐bias (EB) phenomena exploited in most spintronic devices, although still is lack of full understanding. Discordant results, including different exchange‐bias field ( H E ), coercivity ( H C ), or blocking temperature ( T B ) found even in similar systems, are usually ascribed to uncontrolled parameters, namely dissimilar interfacial defects, structure, and thicknesses. Here, it is shown in the very same sample that the magnetic domain structure during the magnetization reversal of the FM layer controls those mentioned effects. Simultaneous transport and vectorial‐resolved magnetic measurements performed in a V 2 O 3 /Co system during warming after different field cooling (FC) procedures exhibit a strong dependence on the FC angle and the domain structure of the FM layer. Remarkably, magnetization reversal analysis reveals 35 K of variation in T B and up to a factor of two in H E . These observations can be explained within the random‐field model for the interfacial exchange coupling with a fixed AFM domain structure in contact with a variable (angle‐dependent) FM domain structure. The results highlight the importance of the domain structure and magnetization reversal of the FM layer (not previously considered) in the EB phenomena, with potential to tailor interfacial effects in future spintronic devices.

36 MATERIALS SCIENCE↗

Polymer Passivated All Inorganic Micro‐Structured CsPbI x Br y Perovskite Toward Highly Efficient Photodetectors

Abstract Solution‐processed inorganic perovskites cause chemical and structural defects unfavorable for photodetector application. Using a binary solvent, defects in CsPbI x Br y (CPIB) perovskite are passivated with poly 4‐vinylpyridine (PVP) and Poly methyl methacrylate (PMMA) polymers. X‐ray photoelectron spectroscopy and FTIR spectra reveal a Lewis base‐acid interaction between Pb 2+ and polymer, confirming the passivation of CPIB perovskite. Scanning electron microscopy analysis shows a dual‐surface morphology with microribbons and microcrystals in perovskites. After PMMA treatment, CPIB perovskite exhibits a blue shift in the bandgap (1.8 to 1.95 eV), while the PVP induced a redshift, reducing the bandgap to 1.7 eV. Blue shift in PL analysis indicates modification of grain boundaries. A higher lifetime obtained for CPIB/PVP confirms the restraint of non‐radiative recombinations. Photodetectors are fabricated with pristine CPIB, CPIB/PVP, and CPIB/PMMA perovskites. The passivated CPIB/PVP‐based photodetector exhibits a quick rise time of ≈23 ms and a decay time of ≈17 ms. It also demonstrates a remarkable photoresponsivity of 23 mA W −1 , an internal quantum efficiency of 4.9%, and a detectivity of 15.0 × 10 10 Jones at 10 mW cm −2 light intensity. This approach shows the potential for environmentally stable polymers to passivate inorganic perovskites for high photodetection performance.

Shah, Shruti↗

Redox‐Mediated Electrochemical Regeneration of Spent LiFePO 4 Battery Cathodes

Direct recycling of lithium-ion battery cathodes offers considerable appeal over metallurgical approaches. Here, we demonstrate a mediated electrochemical method for direct regeneration of degraded LiFePO 4 (LFP). The approach uses a redox mediator, iron propylenediamine tetraacetate, that undergoes electrochemical reduction and is circulated through an external reservoir, where it supplies the electrons needed to regenerate LFP in the presence of Li + ions derived from LiOH oxidation. Rapid outer-sphere electron transfer is observed from the mediator to the degraded LFP material. This feature, together with good aqueous solubility of the mediator (0.3 M), supports current densities up to 100 mA/cm 2 , and this electrochemical recycling process is demonstrated on 100 g scale. 57 Fe Mössbauer spectroscopy is used to monitor the correction of structural defects in the degraded LFP, providing the basis for regeneration of LFP that matches the electrochemical performance of pristine LFP.

Electrochemical Relithiation↗

Single-crystal sapphire microstructure for high-resolution synchrotron X-ray monochromators

We report on the growth and characterization of several sapphire single crystals for the purpose of x-ray optics applications. Structural defects were studied by means of laboratory double-crystal X-ray diffractometry and white beam synchrotron-radiation topography. The investigations confirmed that the main defect types are dislocations. The best quality crystal was grown using the Kyropoulos technique with a dislocation density of 10 2 -10 3 cm -2 and a small area with approximately 2*2 mm 2 did not show dislocation contrast in many reflections and has suitable quality for application as a backscattering monochromator. As a result, a clear correlation between growth rate and dislocation density is observed, though growth rate is not the only parameter impacting the quality.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the Counter‐intuitive Heterogeneous Electron Transfer Barrier Properties of Alkanethiolate Monolayers on Gold: Smooth versus Rough Surfaces

Abstract Alkanethiolate monolayers formed on rough gold surfaces can, somewhat surprisingly, act as stronger barriers to heterogeneous electron transfer than those on smooth gold surfaces. This paper presents a possible explanation for this observation by constructing simple geometric models of a “rough” and “smooth” gold surface to examine how microscopic roughness differences can affect the nucleation/growth of the adlayer and size/density of structural defects. Expectedly, the number of defects predicted for adlayers formed on smooth gold is lower than any of those for rough gold. The counter‐intuitive result is that the sizes of a small portion of the defects in the adlayer on the smooth surface are larger than any of those found on the rough surface. The potential implications of these results are discussed.

Chemistry↗

Dehydration Pathway Study of Ultrathin Ni (OH) 2 Probed via In Situ X-Ray Photoelectron Spectromicroscopy

In this work, the conversion of ultrathin 2D-Ni (OH) 2 to NiO is studied using in situ X-ray absorption near edge spectroscopy at the Ni L 3 and O K edges and using variable photon energy X-ray photoelectron spectroscopy at the Ni 2p 3/2 and O 1s edges. The Ni L 3 X-ray absorption spectroscopy and corresponding 2p 3/2 X-ray photoelectron spectroscopy show the oxidation state of the Ni atom to be Ni 2+ in the course of the reaction; however, the film surface and oxygen defect structure show the presence of a large metallic Ni component before the complete disappearance of the hydroxide phase indicating oxygen vacancy formation before the completion of water desorption. O 1s spectral changes during heat treatment under ultrahigh vacuum, O 2 dosing, and H 2 O dosing suggest the spectral features are due to water desorption and adsorption. Furthermore, by comparing the relative probe depths of X-ray photoelectron spectroscopy and X-ray absorption spectroscopy, it is determined that the surface, at each step in the dehydration process, consists of a combination of Ni, NiO, and Ni (OH) 2 phases, which each contain a mixture of adsorbed hydroxyl groups. Repeated dosing with H 2 O, studied with O 1s X-ray photoelectron spectroscopy, suggests that the dissociation of water facilitates the formation of oxygen vacancies.

36 MATERIALS SCIENCE↗

Bottom‐Up Synthesis of Metallic CoNi Nanoplatelets with Magnetic Vortex‐Like Spin Configurations

Magnetic nanoplatelets hold significant potential for various technical applications due to their ability to switch between a fully magnetized state with high magnetization and a vortex‐like configuration that eliminates stray fields in the absence of an external field. This study presents the synthesis of uniform CoNi nanoplatelets through the topotactic reduction of metal hydroxides using hydrogen plasma. The reduction process is analyzed via magnetometry, leveraging the transition from paramagnetic hydroxide to ferromagnetic metal. Lorentz transmission electron microscopy and scanning transmission X‐ray microscopy confirm the presence of magnetic vortex‐like structures in isolated Co 0.85 Ni 0.15 nanoplatelets at ambient temperature. Additionally, micromagnetic simulations are conducted to further explore the magnetic properties of the nanoplatelets, revealing the formation of magnetic vortex remanent states at diameters between 200 nm and 1 μm and a thickness of around 12 nm. Notably, structural defects and thickness variations do not directly destabilize the magnetic vortex configurations.

Kräenbring, Mena‐Alexander [Faculty of Physics and↗

Photocatalysis and Photoelectrocatalysis Methods of Nitrogen Reduction for Sustainable Ammonia Synthesis

Abstract Ammonia (NH 3 ) is one of the essential chemicals as a fertilizer and as a starting reagent for various chemicals with a production expectation of 200 million tonnes for 2018. With the development of renewable energy technologies such as hydrogen fuel cells, hydrogen also has emerged as an innovative clean energy source. Ammonia is a suitable hydrogen fuel carrier since a molecule of ammonia can carry up to three atoms of hydrogen. Recently, photochemical synthesis via nitrogen reduction has gained considerable attention as a sustainable method for the production of ammonia. The performance of the photoreduction of nitrogen lies in the developments of the photocatalysts and photoelectrocatalysts. Therefore, it is essential to understand the fundamentals of nitrogen reduction processes along with apprehending the challenges that limit the progress of catalysts. In this review, the basic understanding of photoreduction of nitrogen is highlighted, emphasizing on the challenges and effective methods to control defects, structures, and morphologies of materials for the catalyst development. The methods for ammonia detection and uncertainties in calculating the efficiency of the photochemical process are also addressed.

Ithisuphalap, Kemakorn↗

Improved ZnS nanoparticle properties through sequential NanoFermentation

Sequential NanoFermentation (SNF) is a novel process which entails sparging microbially produced gas containing H 2 S from a primary reactor through a concentrated metal-acetate solution contained in a secondary reactor, thereby precipitating metallic sulfide nanoparticles (e.g., ZnS, CuS, or SnS). SNF holds an advantage over single reactor nanoparticle synthesis strategies, because it avoids exposing the microorganisms to high concentrations of toxic metal and sulfide ions. Also, by segregating the nanoparticle products from biological materials, SNF avoids coating nanoparticles with bioproducts that alter their desired properties. Herein, we report the properties of ZnS nanoparticles formed from SNF as compared with ones produced directly in a primary reactor (i.e., conventional NanoFermentation, or “CNF”), commercially available ZnS, and ZnS chemically synthesized by bubbling H 2 S gas through a Zn-acetate solution. The ZnS nanoparticles produced by SNF provided improved optical properties due to their smaller crystallite size, smaller overall particle sizes, reduced biotic surface coatings, and reduced structural defects. Furthermore, SNF still maintained the advantages of NanoFermentation technology over chemical synthesis including scalability, reproducibility, and lower hazardous waste burden.

59 BASIC BIOLOGICAL SCIENCES↗

The Stoichiometry of Synthetic Alunite as a Function of Hydrothermal Aging Investigated by Solid-State NMR Spectroscopy, Powder X-ray Diffraction and Infrared Spectroscopy

The stoichiometry of a series of synthetic alunite [nominally KAl3(SO4)2(OH)6] samples prepared by hydrothermal methods as a function of reaction time (1–31 days) has been investigated by powder X-ray diffraction, Fourier transform infrared spectroscopy as well as solid-state 1H and 27Al magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. The 1H MAS NMR spectra recorded at high magnetic field (21.1 T, 900 MHz) allowed for a clear separation of the different proton environments and for quantitative determination of the aluminum vacancy concentration as a function of time. The concentration of structural defects determined from, i.e., aluminum vacancies was reduced from 4 to 1 %, as the reaction time was extended from one to 31 days based on 1H MAS NMR. This was further supported by an increase of the unit cell parameter c, which is indicative of the relative concentration of potassium defects present, from 17.261(1) to 17.324(5) Å. Solid-state 27Al MAS NMR revealed a decrease in the defect concentration as a function of time and showed the presence of 7–10 % impurities in the samples.

Environmental Molecular Sciences Laboratory↗

Yttrium Oxide Concentration Effect on Helium Porosity Formation in Oxide-Dispersion-Hardened Ferrite-Martensite Steel

Studies are presented of helium porosity in EP-450 oxide-dispersion-hardened yttrium steel, obtained by electopulse sintering, as a function of the Y{sub 2}O{sub 3} content in comparison with EP-450 matrix steel and dispersion-hardened steel fabricated by hot extrusion. It is found that multiple zones with different types of helium porosity and different zone distribution develop in steel with 1 wt.% Y{sub 2}O{sub 3}; in steel with 0.3 wt.% Y{sub 2}O{sub 3}, there are fewer such zones than in matrix steel and steel obtained by hot extrusion. It is proposed that the extremely nonuniform distribution of porosity over volume and size in steel fabricated by electropulse sintering is associated with the initially strongly defective structure, including residual porosity, as well as with the chromium redistribution between ferrite grains and tempered-martensite grains during the sample preparation process.

36 MATERIALS SCIENCE↗

Nucleation and growth of chimney pores during electron-beam additive manufacturing

The nucleation and growth of chimney pores during powder-bed, electron-beam additive manufacturing is investigated using in-situ infrared thermography as well as microcomputed tomography of as-printed parts. The pores are found to nucleate at dimples on the part s surface, clearly demonstrating how process parameters can affect surface roughness, which can in turn affect the internal defect structure in an additive manufactured part. Based on the results of this study, several strategies for suppressing the formation of chimney pores are discussed.

43 PARTICLE ACCELERATORS↗

Computational study of the effect of core–skin structure on the mechanical properties of carbon nanofibers

The effect of the core–skin structure on the mechanical properties of carbon nanofibers is investigated in large-scale molecular dynamics simulations of tensile deformation of carbon nanofibers with the core–skin and homogeneous structures. Contrary to an established notion of the deleterious effect of the skin layer on the strength of carbon fibers, the presence of a high-quality skin layer is found to increase both the Young’s modulus and tensile strength of the nanofiber. A detailed analysis of the fracture process indicates that the nanofiber strengthening is related to the ability of skin layer to suppress crack nucleation at the core–skin interface. Furthermore, the computational predictions suggest that the design of new approaches to carbon fiber manufacturing and processing leading to the generation of a high-quality skin layer while avoiding the introduction of structural defects at the core–skin interface may yield a significant enhancement of the mechanical properties of carbon fibers.

36 MATERIALS SCIENCE↗