Search NASA⌕ Search

SEARCH · Search NASA

Results for “structures testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Galileo spacecraft modal test and evaluation of testing techniques

The structural configuration, modal test requirements and pre-test activities involved in modeling the expected dynamic environment and responses of the Galileo spacecraft are discussed. The probe will be Shuttle-launched in 1986 and will gather data on the Jupiter system. Loads analysis for the 5300 lb spacecraft were performed with the NASTRAN code, and covered 10,000 static degrees of freedom and 1600 mass degrees of freedom. A modal analysis will be used to verify the predictions for natural frequencies, mode shapes, orthogonality checks, residual mass, modal damping and forces, and generalized forces. Verification of the validity of considering only 70 natural modes in the numerical simulation is being performed by examining the forcing functions of the analysis. The analysis led to requirements that 162 channels of accelerometer data and 118 channels of strain gage data be recorded during shaker tests to reveal areas where design changes will be needed to eliminate vibration peaks.

Chen, J.-C.↗
NASA NTRS1983

Technology requirements for large flexible space structures

Research, test, and demonstration experiments necessary for establishing a data base that will permit construction of large, lightweight flexible space structures meeting on-orbit pointing and surface precesion criteria are discussed. Attention is focused on the wrap-rib proof-of-concept antenna structures developed from technology used on the ATS-6 satellite. The target structure will be up to 150 m in diameter or smaller, operate at RF levels, be amenable to packaging for carriage in the Shuttle bay, be capable of being ground-tested, and permit on-orbit deployment and retraction. Graphite/epoxy has been chosen as the antenna ribs material, and the antenna mesh will be gold-plated Mo wire. A 55-m diam reflector was built as proof-of-concept with ground-test capability. Tests will proceed on components, a model, the entire structure, and in-flight. An analytical model has been formulated to characterize the antenna's thermal behavior. The flight test of the 55-m prototype in-orbit offers the chance to validate the analytical model and characterize the control, mechanical, and thermal characteristics of the antenna configuration.

Wada, B. K.↗
NASA NTRS1972

Structural evaluations and dynamic testing of solar electric propulsion components.

Results of an experimental and analytical study of selected Solar Electric Propulsion (SEP) thrust subsystem components are presented. A mass and center-of-mass mockup of an experimental power conditioning (PC) panel was used for the PC structure evaluation. Test environment was based on that specified for prooftesting the Viking spacecraft electronics. Modal frequencies were surveyed over the range of 0-2000 Hz using both conventional test equipment and the holographic interferometry technique. Results of the forced vibration tests point to the need for some additional stiffening to make the structure qualifiable.

Womack, J. R.↗
NASA NTRS1976

Program for establishing long-time flight service performance of composite materials in the center wing structure of C-130 aircraft. Phase 4: Ground/flight acceptance tests

The advantageous structural uses of advanced filamentary composites are demonstrated by design, fabrication, and test of three boron-epoxy reinforced C-130 center wing boxes. The advanced development work necessary to support detailed design of a composite reinforced C-130 center wing box was conducted. Activities included the development of a basis for structural design, selection and verification of materials and processes, manufacturing and tooling development, and fabrication and test of full-scale portions of the center wing box. Detailed design drawings, and necessary analytical structural substantiation including static strength, fatigue endurance, flutter, and weight analyses are considered. Some additional component testing was conducted to verify the design for panel buckling, and to evaluate specific local design areas. Development of the cool tool restraint concept was completed, and bonding capabilities were evaluated using full-length skin panel and stringer specimens.

Harvill, W. E.↗
NASA NTRS2022

Optimization Approach for Wind Tunnel Fan Blade Strain Gage Correlation with Test Fixture Unknowns

NASA has a significant maintenance challenge with the aging wind tunnel infrastructure across the Agency. Some wind tunnel fan blades, such as those in the National Transonic Facility at NASA Langley Research Center, have been in use for far longer than their planned 10-year lifetime. No detailed analytical models of the fan blades from their initial fabrication were created. To support the fabrication of either new, nominally identical fan blades or newly designed fan blades, accurate analytical models of the existing fan blades are necessary to demonstrate an understanding of the capabilities of the existing fan blades. Additionally, the existing documentation of the testing of the existing fan blades has gaps. In this report, a process for improving test-analysis correlation for these wind tunnel fan blades is discussed. This process involved a detailed study of unknown parameters in test fixture parameters from the old and incomplete test documentation. To improve correlation, these unknown parameters were used as design variables in an optimization study to minimize the error between test data and computed structural responses. Legacy strain gage data from tests conducted in 1981 were compared with results from a finite element model created in 2019. The use of test data from 1981 was necessary because none of the existing fan blades could be spared for use in destructive structural testing. While this process was demonstrated for wind tunnel fan blades, this process could be utilized for evaluating unknowns in test fixtures for other structural test configurations.

wind tunnel↗
NASA NTRS1974

Estimation of structural parameters from dynamic test data

Parameters for a lumped linear model approximating a distributed elastic structure are determined from dynamic test data comprised of several mode shapes and frequencies. Measurement errors, nonlinear response, and nonmeasurable quantities such as mode slope components are accommodated. Some mass and stiffness parameters may be known accurately, whereas the remainder are to be estimated. The method entails minimizing a quadratic function of the difference between corresponding modes and frequencies of the theoretical model and the test specimen. This technique was applied to some actual vibration test data, and the special techniques that are required to overcome convergence problems are described.

Hall, B. M.↗
NASA NTRS1982

Mobile work station concept for assembly of large space structures (zero gravity simulation tests)

The concept presented is intended to enhance astronaut assembly of truss structure that is either too large or complex to fold for efficient Shuttle delivery to orbit. The potential of augmented astronaut assembly is illustrated by applying the result of the tests to a barebones assembly of a truss structure. If this structure were assembled from the same nestable struts that were used in the Mobile Work Station assembly tests, the spacecraft would be 55 meters in diameter and consist of about 500 struts. The struts could be packaged in less than 1/2% of the Shuttle cargo bay volume and would take up approximately 3% of the mass lift capability. They could be assembled in approximately four hours. This assembly concept for erectable structures is not only feasible, but could be used to significant economic advantage by permitting the superior packaging feature of erectable structures to be exploited and thereby reduce expensive Shuttle delivery flights.

Heard, W. L., Jr.↗
NASA NTRS1976

Evaluation of Materials and Concepts for Aircraft Fire Protection

Woven fiberglass fluted-core simulated aircraft interior panels were flame tested and structurally evaluated against the Boeing 747 present baseline interior panels. The NASA-defined panels, though inferior on a strength-to-weight basis, showed better structural integrity after flame testing, due to the woven fiberglass structure.

Anderson, R. A.↗
NASA NTRS2002

High Temperature Spin Testing of a Superalloy Disk With a Dual Grain Structure

Comparative spin tests were run on superalloy disks at an elevated temperature to determine the benefits of a DMHT disk, with a fine grain bore and coarse grain rim, versus a traditional subsolvus disk with a fine grain structure in the bore and rim. The results of these tests showed that the DMHT disk exhibited significantly lower growth at 1500 F. Further, the results of these tests could be accurately predicted using a 2D viscoelastic finite element analysis. These results indicate DMHT technology can be used to extend disk operating temperatures when compared to traditional subsolvus heat treatment options for superalloy disks. However, additional research is required to ensure the safe operation of a DMHT disk under more realistic engine operating conditions. This includes testing to determine the burst margin and cyclic capability of DMHT disks in a spin pit, at a minimum, and ultimately running an engine test with a DMHT disk.

Gayda, John↗
NASA NTRS1969

Ground testing the Apollo vehicle.

Static structure ground test for Saturn-Apollo vehicle short stack, describing air pressure simulation, data acquisition and readout systems

Reese, D. R.↗
NASA NTRS1984

Definition of ground test for Large Space Structure (LSS) control verification

An overview for the definition of a ground test for the verification of Large Space Structure (LSS) control is given. The definition contains information on the description of the LSS ground verification experiment, the project management scheme, the design, development, fabrication and checkout of the subsystems, the systems engineering and integration, the hardware subsystems, the software, and a summary which includes future LSS ground test plans. Upon completion of these items, NASA/Marshall Space Flight Center will have an LSS ground test facility which will provide sufficient data on dynamics and control verification of LSS so that LSS flight system operations can be reasonably ensured.

Waites, H. B.↗
NASA NTRS1985

Ground test experiment for large space structures

In recent years a new body of control theory has been developed for the design of control systems for Large Space Structures (LSS). The problems of testing this theory on LSS hardware are aggravated by the expense and risk of actual in orbit tests. Ground tests on large space structures can provide a proving ground for candidate control systems, but such tests require a unique facility for their execution. The current development of such a facility at the NASA Marshall Space Flight Center (MSFC) is the subject of this report.

Tollison, D. K.↗
NASA NTRS1987

Ground test of large flexible structures

Many future mission models require large space (LSS) which have accurate surfaces and/or the capability of being accurately aligned. If ground test approaches which will provide adequate confidence of the structrual performance to the program managers are not developed, many viable structural concepts may never be utilized. The size and flexibility of many of the structural concepts will preclude the use of the current ground test methods because of the adverse effects of the terrestrial environment. The challenge is to develop new test approaches which will provide confidence in the capability of LSS to meet performance requirements prior to flight. The activities on ground testing of LSS are described. Since some of the proposed structural systems cannot be tested in entirety, a coordinated ground test analytical model program is required to predict structural performance in space. Several concepts of ground testing under development are addressed.

Wada, Ben K.↗
NASA NTRS1985

Structural analysis model validation using modal test data

The design of a structure which can survive a prescribed dynamic environment is generally based on the use of an analytical model of the structure. The modal test is employed to verify the analytical model. This paper is concerned with the involved validation process, taking into account modal test results from realistic complex spacecraft structural systems as examples to demonstrate the proposed validation procedure. Attention is given to a load analysis model definition, a pretest analysis and test/analysis model, and the correlation parameters. Coordinate transformation is considered along with mode identification, frequency orthogonality, effective mass, mode shape, local kinetic energy, modal force, strain energy, and modal forces by acceleration measurements. Two examples are used to illustrate the procedure.

Chen, J.-C.↗
NASA NTRS1987

Structural and preliminary thermal performance testing of a pressure activated contact heat exchanger

A contact heat exchanger concept is being developed for use onboard Space Station as an interface device between external thermal bus and pressurized modules. The concept relies on mechanical contact activated by the fluid pressure inside thin-walled tubes. Structural testings were carried out to confirm the technology feasibility of using such thin-walled tubes. The test results also verified the linear elastic stress analysis which was used to predict the tube mechanical behaviors. A preliminary thermal testing was also performed with liquid Freon-11 flowing inside tubes and heat being supplied by electrical heating from the bottom of the contact heat exchanger baseplate. The test results showed excellent agreement of test data with analytical prediction for all thermal resistances except for the two-phase flow characteristics. Testing with two-phase flow inside tubes will, however, be performed on the NASA-JSC test bed.

Lee, C. Y.↗
NASA NTRS1990

End-of-fabrication CMOS process monitor

A set of test 'modules' for verifying the quality of a complementary metal oxide semiconductor (CMOS) process at the end of the wafer fabrication is documented. By electrical testing of specific structures, over thirty parameters are collected characterizing interconnects, dielectrics, contacts, transistors, and inverters. Each test module contains a specification of its purpose, the layout of the test structure, the test procedures, the data reduction algorithms, and exemplary results obtained from 3-, 2-, or 1.6-micrometer CMOS/bulk processes. The document is intended to establish standard process qualification procedures for Application Specific Integrated Circuits (ASIC's).

Buehler, M. G.↗