Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Stress induced enhanced polarization in multilayer BiFeO{sub 3}/BaTiO{sub 3} structure with improved energy storage properties

Present work reports the fabrication of a multilayer (5-layer) structure of BiFeO{sub 3}(BFO)/BaTiO{sub 3}(BTO) using spin-coating technique. The crystallographic structure, surface morphology and ferroelectric behavior of multilayer structure in metal-ferroelectric-metal capacitor have been studied. Le-Bail refinement of X-ray diffraction data revealed the formation of polycrystalline pure perovskite phase with induced stress. The values of remnant (P{sub r}) and saturation polarization (P{sub s}) for BFO/BTO multilayer structure are found to be 38.14 μC/cm{sup 2} and 71.54 μC/cm{sup 2} respectively, which are much higher than the corresponding values reported for bare BFO thin film. A large value of dielectric constant of 187 has been obtained for multilayer structure with a low leakage current density of 1.09 × 10{sup −7} A/cm{sup 2} at applied bias of 10 V. The BFO/BTO multilayer structure favors the enhanced energy storage capacity as compared to bare BFO thin film with improved values of energy-density and charge-discharge efficiency as 121 mJ/cm{sup 3} and 59% respectively, suggesting futuristic energy storage applications.

36 MATERIALS SCIENCE↗

Influence of C or In buffer layer on photoluminescence behaviour of ultrathin ZnO film

We study the effect of the indium or carbon buffer layer on the photoluminescence (PL) property of ZnO ultrathin films deposited on a Si(100) substrate. The surface morphology of the films obtained using scanning tunnelling microscopy shows spherical shaped ZnO nanoparticles of size ∼8 nm in ZnO/C/Si and ∼22 nm in ZnO/Si samples, while the ZnO/In/Si sample shows elliptical shaped ZnO particles. Further, the ZnO/C/Si sample shows densely packed ZnO nanoparticles in comparison with other samples. Strong band edge emission has been observed in the presence of In or C buffer layer, whereas the ZnO/Si sample exhibits poor PL emission. The influence of C and In buffer layers on the PL behaviour of ZnO films is studied in detail using temperature dependent PL measurements in the range of 4 K–300 K. The ZnO/C/Si sample exhibits a multi-fold enhancement in the PL emission intensity with well-resolved free and bound exciton emission lines. Our experimental results imply that the ZnO films deposited on the C buffer layer showed higher particle density and better exciton emission desired for optoelectronic applications.

36 MATERIALS SCIENCE↗

Orbital orientation mapping of V 2 O 5 thin films

We report the effects of growth methods on the orbital orientation in vanadium pentoxide (V 2 O 5 ) thin films, an important factor to consider when selecting growth techniques for highly selective catalysts and devices. Thermal evaporation and sol-gel methods were used to synthesize the V 2 O 5 films. The surface morphology, roughness, and orientation of the films were characterized by atomic force microscopy and x-ray diffraction. Surface electronic properties and oxidation states were assessed by x-ray photoemission spectroscopy. Polarized x-ray absorption spectroscopy demonstrated that the thermally evaporated film [which was in the (001) orientation] exhibited greater anisotropy than the (100) oriented sol-gel film. The observed increase in anisotropy agrees well with computational findings which revealed that more vanadyl bonds are present at the surface of the thermally evaporated film than at the surface of the sol-gel film. The same computational study also found that the orientation of these bonds is more parallel to the film surface in the thermally evaporated film than in the sol-gel film. Finally, the data suggest that the method of growth may be used as a controlled variable to select key film characteristics for potential applications.

36 MATERIALS SCIENCE↗

Influence of substrate temperature on structural and optical properties of RF sputtered ZnMnO thin films

The ZnMnO thin films were deposited on glass substrates by radio frequency magnetron sputtering method. The properties of ZnMnO thin films were investigated by high-resolution x-ray diffractometer (HRXRD),atomic force microscopy (AFM), UV-Vis spectrometer and room temperature photoluminescence (PL), under the influence of substrate temperature. The substrate temperature was varied from 300, 400 and 500°C. With increasing the substrate temperature, the structure of the films changed from cubic to hexagonal. The cubic ZnMnO thin films grown along [210] direction, while the hexagonal ones grown along [002] direction. The changes in surface morphology provided a proof on the structural transition. Also, decrease and increase of optical band gap is associated with cubic or hexagonal structure of the films.

36 MATERIALS SCIENCE↗

Effect of self-organization, defects, impurities, and autocatalytic processes on the parameters of ZnO films and nanorods

The effects of the parameters of ZnO-film deposition onto different substrates using the method of ac magnetron sputtering in a gas mixture of argon and oxygen hare studied. The phenomenon of self-organization is observed, which leads to invariability of the surface morphology of the ZnO films upon a variation in the substrate materials and deposition parameters. The parameters of the macro- and micro-photoluminescence spectra of the films differ insignificantly from the parameters of the photoluminescence spectra of bulk ZnO crystals obtained by the method of hydrothermal growth. The presence of intense emission with a narrow full-width at half-maximum (FWHM) in different regions of the spectrum allows ZnO films obtained by magnetron sputtering doped with rare-earth metal impurities (REIs) to be considered as a promising material for the creation of optoelectronic devices working in a broad spectral range. The possibility of the implementation of magnetic ordering upon legierung with REIs significantly broadens the functional possibilities of ZnO films. The parameters of the photoluminescence spectra of ZnO nanorods are determined by their geometrical parameters and by the concentration and type of the impurities introduced.

36 MATERIALS SCIENCE↗

Investigating the RTA Treatment of Ohmic Contacts to n-Layers of Heterobipolar Nanoheterostructures

The preparation of ohmic contacts to heterobipolar nanostructures has a number of characteristic features. In addition to the basic requirement of minimizing contact resistance, contacts to this type of structures have a transition layer whose depth of penetration must not exceed the emitter layer’s thickness, due to the possibility of short-circuiting the emitter base p–n junction. In this work, the effect the main technological parameters of rapid thermal annealing have on a contact’s characteristics are examined, and the process of obtaining a low-resistance ohmic contact to heterobipolar transistor layers is optimized. Ohmic contacts to the n-layers of heterobipolar nanoheterostructures based on gallium arsenide and produced via layer-by-layer electron-beam deposition of Ge/Au/Ni/Au are considered. The diffusion distribution profiles of doping with Ge impurities are calculated as a function of the time and temperature of rapid thermal annealing, and are examined via scanning electron microscopy. It is found that rapid thermal annealing for 60 s at a temperature of 398°C yields ohmic contacts with low resistance, smooth surface morphology, and the minimum size of the transition layer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Kenaf Bast Fibers—Part II: Inorganic Nanoparticle Impregnation for Polymer Composites

The objective of this study was to investigate an inorganic nanoparticle impregnation (INI) technique to improve the compatibility between kenaf bast fibers and polyolefin matrices. The Scanning Electron Microscopy (SEM) was used to examine the surface morphology of the INI-treated fibers showing that the CaCO 3 nanoparticle crystals grew onto the fiber surface. Energy-dispersive X-ray spectroscopy (EDS) was used to verify the CaCO 3 nanoparticle deposits on the fiber surface. The tension tests of the individual fiber were conducted, and the results showed that the tensile strength of the fibers increased significantly (more than 20%) after the INI treatments. Polymer composites were fabricated using the INI-treated fiber as reinforcement and polypropylene (PP) as the matrix. The results showed that the INI treatments improved the compatibility between kenaf fibers and PP matrix. The tensile modulus and tensile strength of the composites reinforced with INI-treated fibers increased by 25.9% and 10.4%, respectively, compared to those reinforced with untreated kenaf fibers.

Shi, Jinshu↗

Fabrication of Monolithic Sapphire Membranes for High Tc Bolometer Array Development

This paper examines the effectiveness of Pt/Cr thin film masks for the architecture of monolithic membrane structures in r-plane sapphire. The development of a pinhole-free Pt/Cr composite mask that is resistant to hot H2SO4:H3PO4 etchant, will lead to the fabrication of smooth sapphire membranes whose surfaces are well-suited for the growth of low-noise high Tc films. In particular, the relationship of thermal annealing conditions on the Pt/Cr composite mask system to: (1) changes in the surface morphology and elemental concentration of the Pt/Cr thin film layers and (2) etch pit formation on the sapphire surface will be presented.

Pugel, D. E.↗

Fabrication of Monolithic Sapphire Membranes for High T(sub c) Bolometer Array Development

This paper examines the effectiveness of Pt/Cr thin film masks for the architecture of monolithic membrane structures in r-plane single crystal sapphire. The development of a pinhole-free Pt/Cr composite mask that is resistant to boiling H2SO4:H3PO4 etchant will lead to the fabrication of smooth sapphire membranes whose surfaces are well-suited for the growth of low-noise high Tc films. In particular, the relationship of thermal annealing conditions on the Pt/Cr composite mask system to: (1) changes in the surface morphology (2) elemental concentration of the Pt/Cr thin film layers and (3) etch pit formation on the sapphire surface will be presented.

Pugel, D. E.↗

Atomic Force Microscope Observation of Growth and Defects on As-Grown (111) 3C-SiC Mesa Surfaces

This paper presents experimental atomic force microscope (AFM) observations of the surface morphology of as-grown (111) silicon-face 3C-SiC mesa heterofilms. Wide variations in 3C surface step structure are observed as a function of film growth conditions and film defect content. The vast majority of as-grown 3C-SiC surfaces consisted of trains of single bilayer height (0.25 nm) steps. Macrostep formation (i.e., step-bunching) was rarely observed, and then only on mesa heterofilms with extended crystal defects. As supersaturation is lowered by decreasing precursor concentration, terrace nucleation on the top (111) surface becomes suppressed, sometimes enabling the formation of thin 3C-SiC film surfaces completely free of steps. For thicker films, propagation of steps inward from mesa edges is sometimes observed, suggesting that enlarging 3C mesa sidewall facets begin to play an increasingly important role in film growth. The AFM observation of stacking faults (SF's) and 0.25 nm Burgers vector screw component growth spirals on the as-grown surface of defective 3C films is reported.

Neudeck, Philip G.↗

Phase Segregation in Polystyrene?Polylactide Blends

Spun-cast films of polystyrene (PS) blended with polylactide (PLA) were visualized and characterized using atomic force microscopy (AFM) and synchrotron-based X-ray photoemission electron microscopy (X-PEEM). The composition of the two polymers in these systems was determined by quantitative chemical analysis of near-edge X-ray absorption signals recorded with X-PEEM. The surface morphology depends on the ratio of the two components, the total polymer concentration, and the temperature of vacuum annealing. For most of the blends examined, PS is the continuous phase with PLA existing in discrete domains or segregated to the air?polymer interface. Phase segregation was improved with further annealing. A phase inversion occurred when films of a 40:60 PS:PLA blend (0.7 wt percent loading) were annealed above the glass transition temperature (Tg) of PLA.

36 MATERIALS SCIENCE↗

Behavior of high-burnup advanced LWR fuels under accident conditions

Advanced fuels for LWRs which consist of cladding materials with high corrosion resistance and pellets with lower fission gas release have been developed by utilities and fuel vendors to improve the fuel performance even in the high burnup region and also raise the safety level of current nuclear power plants to a higher one. In order to evaluate the adequacy of present safety criteria and safety margins in terms of such advanced fuels and provide a database for future regulation of them, JAEA has started a new extensive research program called ALPS-II program. The ALPS-II program is primarily composed of tests simulating a RIA (Reactivity Initiated Accident) (VA-5 and -6 tests) and a LOCA (Loss Of Coolant Accident) on high burnup advanced fuels irradiated in commercial PWR or BWRs and started in JFY 2008. Recently, post-test examinations on the fuel rods after the pulse irradiation tests of VA-5 and -6 were performed and the relationship between the failure limits of the high burnup advanced fuels with M-MDA{sup TM} cladding and the morphology of the hydrides precipitated in the cladding during normal operation was investigated. The difference in the crack surface morphology was observed between tests VA-5 and-6, which seemed to reflect the difference in the direction along which hydrides precipitate in the cladding. This indicates that the hydride precipitated in the cladding, which is considered to be dependent on the final heat treatment at fabrication, affects the fuel enthalpy at failure. In terms of the simulated LOCA test, integral thermal shock tests and high temperature oxidation tests have been conducted on high burnup PWR and BWR fuel cladding with advanced materials, and their fracture limits, high temperature oxidation rates, etc. were investigated. In the recent integral thermal shock tests for high burnup BWR cladding, namely Zry-2/LK3 material, no fractures were observed. In terms of the oxidation rate tests, the oxidation rate of irradiated M5{sup TM} was similar to those of unirradiated Zry-4 and M5{sup TM} and lower than the values estimated by the Baker-Just equation. From the results of these tests, it was found that in terms of these materials the fracture boundaries do not decrease and the oxidation does not significantly accelerate in the burnup level examined.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Nanostructure and Composition of Tribo-Boundary Films Formed in Ionic Liquid Lubrication

Since the idea of using ionic liquids (ILs) as lubricants was raised in 2001, many studies have been conducted in this area and results have demonstrated superior lubricating performance for a variety of ionic liquids. It is widely believed that tribochemical reactions occur between the metal surface and the IL during the wear process to form a protective tribo-boundary film on the contact area that reduces friction and wear. However, the study of this critical boundary film has been limited to top surface two-dimensional topography examination and chemical analysis in the literature. A more comprehensive characterization is needed to help understand the film formation process and the lubricating mechanism. This study demonstrated a multi-technique three-dimensional approach to characterize the IL-formed boundary films, including top surface morphology examination, cross section nanostructure characterization, and layered chemical analysis. Characterization was carried out on both ferrous and aluminum surfaces lubricated by an ammonium IL. The focused-ion-beam (FIB) technique enabled TEM/EDS examination on the cross section of the boundary film to provide direct measurement of the film thickness, visualization of the nanostructure, and analysis of composition. In addition, composition-depth profiles were generated using XPS aided by ion-sputtering to reveal the composition change at different levels of the boundary film to investigate the film formation process.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Scanning Transmission X-ray Microscopy: Applications in Atmospheric Aerosol Research

Scanning transmission x-ray microscopy (STXM) combines x-ray microscopy and near edge x-ray absorption fine structure spectroscopy (NEXAFS). This combination provides spatially resolved bonding and oxidation state information. While there are reviews relevant to STXM/NEXAFS applications in other environmental fields1-4 (and magnetic materials5) this chapter focuses on atmospheric aerosols. It provides an introduction to this technique in a manner approachable to non-experts. It begins with relevant background information on synchrotron radiation sources and a description of NEXAFS spectroscopy. The bulk of the chapter provides a survey of STXM/NEXAFS aerosol studies and is organized according to the type of aerosol investigated. The purpose is to illustrate the current range and recent growth of scientific investigations employing STXM-NEXAFS to probe atmospheric aerosol morphology, surface coatings, mixing states, and atmospheric processing.

43 PARTICLE ACCELERATORS↗

Changes to the morphology, structure and properties as a consequence of polyethylene working in a polymer-metal kinematic pair

A change is presented of the orientation of lamellar structure, degree of crystallinity, the degree of the spatial arrangement of the structure, micromechanical properties, and the surface morphology and thickness of a plastically deformed upper layer. These changes are the effect of work in a polymer-metal kinematic pair, which have occurred as a result of plastic deformation of polyethylene during its service. It has been shown that, as a result of selecting proper parameters of UHMW polyethylene via the initial draft and electron-beam irradiation, such a structure of the polymer can be obtained, which will enable the above-mentioned changes in morphology and structure to take place during service. This in turn, will allow a reduction of the susceptibility of the polymer to permanent deformation by 3-6 times, and its wear by more than 5 times, compared to the initial material.

36 MATERIALS SCIENCE↗

Structural and electronic properties of InN epitaxial layer grown on c-plane sapphire by chemical vapor deposition technique

Growth of InN epilayers on c-plane sapphire substrate by chemical vapor deposition technique using pure indium metal and ammonia as precursors has been systematically explored. It has been found that [0001] oriented indium nitride epitaxial layers with smooth surface morphology can be grown on c-plane sapphire substrates by optimizing the growth conditions. Bandgap of the film is observed to be Burstein–Moss shifted likely to be due to high background electron concentration. It has been found that the concentration of this unintentional doping decreases with the increase in the growth temperature and the ammonia flux. Epitaxial quality on the other hand deteriorates as the growth temperature increases. Moreover, the morphology of the deposited layer has been found to change from flat top islands to faceted mounds as the flow rate of ammonia increases. This phenomenon is expected to be related to the difference in surface termination character at low and high ammonia flow rates.

36 MATERIALS SCIENCE↗

Real-time studies of surface roughness development and reticulation mechanism of advanced photoresist materials during plasma processing

Surface roughness development of photoresist (PR) films during low pressure plasma etching has been studied using real-time laser light scattering from photoresist materials along with ellipsometric and atomic force microscopy (AFM) characterization. We show that evolution of the intensity of light scattered from a film surface can be used to study the development of surface roughness for a wide range of roughness starting from subnanometer to few hundred nanometers. Laser light scattering in combination with ellipsometry and AFM is also used to study the reticulation mechanism of 193 and 248 nm PRs during argon plasma processing. We employ a three-layer model (modified layer, rough layer, and bulk film) of the modified PR surface (193 and 248 nm PRs) to simulate and understand the behavior of ellipsometric {psi}-{delta} trajectories. Bruggeman's effective medium approximation is employed to study the roughness that develops on the surface after reticulation. When the glass transition temperature of the organic materials is reached during Ar plasma processing, the PR films reticulate and roughness develops rapidly. Roughness development is more pronounced for 248 nm PR than for 193 nm PR. Simulation of {psi}-{delta} shows that the growth of roughness is accompanied by strong expansion in the materials, which is stronger for 248 nm PR than 193 nm PR. The leading factors responsible for reticulation are found to be compressive stress that develops in the modified surface layer as it is created along with strong molecular chain motion and expansion of the material when the temperature is increased past the glass transition temperature. Reticulation leads to a significantly different surface morphology for 248 nm PR as compared to 193 nm PR and can be related to differences in molecular structure and composition leading to different responses when a modified surface layer is formed by ion bombardment accompanying plasma etching.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characteristics and mechanisms of hydrogen-induced quasi-cleavage fracture of lath martensitic steel

Here this study presents an in-depth characterization of the microstructures, crystallographic orientations, and dislocation characteristics beneath hydrogen-induced quasi-cleavage fracture features of an as-quenched, lath martensitic (α') 22MnB5 steel. The fracture surfaces of gaseous hydrogen-embrittled martensitic specimens were analyzed by a combination of multiple analytical tools: scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and transmission Kikuchi diffraction (TKD). The dominant fracture mode in the hydrogen-affected zones was quasi-cleavage fracture, which involved significant plasticity, evidenced by plastic zones near tear ridges and a high density of dislocations beneath the quasi-cleavage facets. The martensite constituent sizes, variant orientations, and boundaries influenced the quasi-cleavage surface morphologies. Fractography revealed the occurrence of {100} α' -type cleavage across martensitic laths, developing relatively “flat” quasi-cleavage surfaces, in addition to {110} α' -type cracking likely along lath and block boundaries, and fracture along non-cleavage planes. The likelihood of the formation of the relatively “flat” quasi-cleavage surfaces increased with increasing martensitic constituent sizes. Substantial dislocation bands formed on intersecting {112} α' slip planes within a martensite block below the hydrogen-induced cleavage fractures on {100} α' planes. River markings on the quasi-cleavage surfaces were found to originate from the complex, hierarchical lath martensitic microstructure. Steps and ridges on the quasi-cleavage facets generally linked with the various martensitic boundaries, suggesting that they were produced as a result of crack deviations at those boundaries. The fracture paths and martensite quasi-cleavage mechanisms are discussed in the context of the role of hydrogen and Cottrell cleavage model.

36 MATERIALS SCIENCE↗