Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Work function reduction in lanthanum hexaboride hollow cathodes operated in gas discharges

Thermal characterization of lanthanum hexaboride (LaB6) hollow cathodes has revealed lower than expected electron emitter temperatures when the cathode reaches steady state. This phenomenon is observed at discharge currents ranging from 5 to 35 A and xenon mass ow rates of 5 to 25 sccm in cathodes with three di erent ori ce diameters. Thus, the accepted value of the work function for polycrystalline LaB6, 2.66 eV, does not describe well the emission characteristics of LaB6 hollow cathodes operating with internal gas discharges at steady state. The measured temperatures and a model of the hollow cathode emitter and xenon discharge were used to estimate the value of the work function in these experiments, yielding a value ranging from 2.1 - 2.44 eV. Measurements of the work function as a function of depth on a hollow cathode emitter using X-ray photoelectron spectroscopy and ion beam milling indicate that the work function in a thin layer near the emitting surface is lower than in the bulk material. We postulate that a lanthanum-rich emitting surface with a lower work function develops as a result of lanthanum recycling in the internal plasma.

Lopez Ortega, Alejandro↗

Post-test Inspection of NASA’s Evolutionary Xenon Thruster Long-Duration Test Hardware: Discharge and Neutralizer Cathodes

The NEXT Long-Duration Test is part of a comprehensive thruster service life assessment intended to demonstrate overall throughput capability, validate service life models, quantify wear rates as a function of time and operating condition, and identify any unknown life-limiting mechanisms. The test was voluntarily terminated in February 2014 after demonstrating 51,184 h of high-voltage operation, 918 kg of propellant throughput, and 35.5 MN-s of total impulse. The post-test inspection of the thruster hardware began shortly afterwards with a combination of non-destructive and destructive analysis techniques, and is presently nearing completion. This paper presents relevant results of the post-test inspection for both discharge and neutralizer cathodes. Discharge keeper erosion was found to be significantly reduced from what was observed in the NEXT 2 kh wear test and NSTAR Extended Life Test, providing adequate protection of vital cathode components throughout the test with ample lifetime remaining. The area of the discharge cathode orifice plate that was exposed by the keeper orifice exhibited net erosion, leading to cathode plate material building up in the cathode-keeper gap and causing a thermally-induced electrical short observed during the test. Significant erosion of the neutralizer cathode orifice was also found and is believed to be the root cause of an observed loss in flow margin. Deposition within the neutralizer keeper orifice as well as on the downstream surface was thicker than expected, potentially resulting in a facility-induced impact on the measured flow margin from plume mode. Neutralizer keeper wall erosion on the beam side was found to be significantly lower compared to the NEXT 2 kh wear test, likely due to the reduction in beam extraction diameter of the ion optics that resulted in decreased ion impingement. Results from the post-test inspection have led to some minor thruster design improvements.

Ion engine↗

Beam Dynamics Simulations of Optically-Enhanced Field Emission from Structured Cathodes

Structured cathodes - cathodes with a segmented emission surface - are finding an increasing number of applications and can be combined with a variety of emission mechanisms, including photoemission and field emission. These cathodes have been used to enhance the quantum efficiency of metallic cathodes when operated as plasmonic cathodes, have produced high-current electron bunches though field emission from multiple tips, and can be used to form beams with transverse segmentations necessary for improving the performance of accelerator-based light sources. In this report we present recent progress towards the development of finite-difference time-domain particle-in-cell simulations using the emission process in structured cathodes based on the WARP framework. The simulations give further insight on the localized source of the emitted electrons which could be used for additional high-fidelity start-to-end simulations of electron accelerators that employ this type of electron source.

43 PARTICLE ACCELERATORS↗

Reflective article having a sacrificial cathodic layer

The present invention relates to reflective articles, such as solar mirrors, that include a sacrificial cathodic layer. The reflective article, more particularly includes a substrate, such as glass, having a multi-layered coating thereon that includes a lead-free sacrificial cathodic layer. The sacrificial cathodic layer includes at least one transition metal, such as a particulate transition metal, which can be in the form of flakes (e.g., zinc flakes). The sacrificial cathodic layer can include an inorganic matrix formed from one or more organo-titanates. Alternatively, the sacrificial cathodic layer can include an organic polymer matrix (e.g., a crosslinked organic polymer matrix formed from an organic polymer and an aminoplast crosslinking agent). The reflective article also includes an outer organic polymer coating, that can be electrodeposited over the sacrificial cathodic layer.

36 MATERIALS SCIENCE↗

Direct regeneration of lithium ion cathodes by ionothermal relithiation

A method for relithiating cathode material from spent lithium-based batteries, the method comprising: (i) mixing delithiated cathode material and a lithium salt with an ionic liquid in which the lithium salt is at least partially soluble to form an initial mixture; (ii) heating the initial mixture to a temperature of 100° C. to 300° C. to result in relithiation of the delithiated cathode material; and (iii) separating the ionic liquid from the relithiated cathode material; wherein, in embodiments, the cathode material is a lithium metal oxide, wherein the metal is selected from the group consisting of Ni, Co, Fe, Mn, Al, Zr, Ti, Nb, and combinations thereof, or wherein the cathode material has the formula LiNi x Mn y Co z O 2 , wherein x>0, y>0, z>0, and x+y+z=1; wherein, in some embodiments, the ionic liquid has a nitrogen-containing cationic portion, such as an imidazolium ionic liquid.

Luo, Huimin↗

Ethylene Carbonate–Free Electrolytes for High–Nickel Layered Oxide Cathodes in Lithium–Ion Batteries

Layered lithium nickel oxide (LiNiO 2 ) can provide very high energy density among intercalation cathode materials for lithium-ion batteries, but suffers from poor cycle life and thermal-abuse tolerance with large lithium utilization. In addition to stabilization of the active cathode material, a concurrent development of electrolyte systems of better compatibility is critical to overcome these limitations for practical applications. Here, with nonaqueous electrolytes based on exclusively aprotic acyclic carbonates free of ethylene carbonate (EC), superior electrochemical and thermal characteristics are obtained with an ultrahigh-nickel cathode (LiNi 0.94 Co 0.06 O 2 ), capable of reaching a 235 mA h g –1 specific capacity. Pouch-type graphite | LiNi 0.94 Co 0.06 O 2 cells in EC-free electrolytes withstand several hundred charge–discharge cycles with minor degradation at both ambient and elevated temperatures. In thermal-abuse tests, the cathode at full charge, while reacting aggressively with EC-based electrolytes below 200 °C, shows suppressed self-heating without EC. Through 3D chemical and structural analyses, the intriguing impact of EC is visualized in aggravating unwanted surface parasitic reactions and irreversible bulk structural degradation of the cathode at high voltages. Finally, these results provide important insights in designing high-energy electrodes for long-lasting and reliable lithium-ion batteries.

25 ENERGY STORAGE↗

A High Energy–Density, Cobalt–Free, Low–Nickel LiNi 0.7 Mn 0.25 Al 0.05 O 2 Cathode with a High–Voltage Electrolyte for Lithium–Metal Batteries

Cobalt-free cathode materials have garnered increased attention for applications in next-generation batteries for electric vehicles, as cobalt is considered to have at a high supply chain risk. Here, the use of a localized saturated electrolyte (LSE) to enable stable cycling of a cobalt-free, low-nickel layered-oxide cathode LiNi 0.7 Mn 0.25 Al 0.05 O 2 (NMA-70) to higher voltages (4.6 V) in a lithium-metal battery is demonstrated. Compared to the baseline LP57 electrolyte, the LSE extends the cycle life from ≈100 cycles to ≈400 cycles before reaching 80% capacity retention. Visual indicators of cell degradation, such as product deposition, are observed on electrodes cycled in LP57. It is shown that cycling NMA-70 in LSE reduces the overall active material loss and overpotential growth during extended cycling. This is attributed to the formation of a beneficial fluorinated interphase layer, a lower degree of rock-salt phase formation, and a reduction in the gas evolution from the cathode surface. The decrease in gas evolution from the cathode cycled in LSE reflects a lower degree of electrolyte reactivity and an overall improvement in the safety characteristics of the cell. Furthermore, this study highlights the importance of a stable electrolyte to enable the high-voltage cycling of alternative, lower nickel, and cobalt-free cathodes.

25 ENERGY STORAGE↗

Cathode Upcycling for Direct Recycling of Lithium‐Ion Batteries Using a Precipitation Approach

With the increased production of electric vehicles to reduce carbon emissions, the lithium-ion battery market to supply those vehicles has grown dramatically. To enhance battery sustainability and circularity, direct recycling methods aim to recover intact cathode materials. However, end-of-life cathode materials are typically 15–20 years old and often have lower energy density compared to current cathode materials. To address this challenge, a rapid precipitation process is developed to boost energy density by converting low Ni-compositions, LiNi 0.33 Co 0.33 Mn 0.33 O 2 (NMC111), into higher Ni-compositions (NMC622). This process forms a Ni-rich coating on cathode particles that diffuses into the core upon high-temperature relithiation, increasing compositional homogeneity. The upcycling process leverages existing infrastructure, offering low capital cost and minimal additional chemical input. Through ex situ tomographic transmission X-ray microscopy (TXM), 3D Ni:Co elemental mixing is quantified, confirming that elemental content evens at the secondary particle level with a mean NMC622 composition upon relithiation. However, elemental gradients remain in the single crystalline primary particles. Ex situ high-resolution and in situ wide-angle X-ray diffraction reveals concurrent structural changes during the relithiation process. These findings provide key insights into the structural and chemical mechanisms of elemental diffusion to obtain further improvements of increased capacity and retention through compositional conversion of cathode materials.

Cathode Upcycling↗

Electrochemical characterization of B-site cation-excess Pr 2 Ni 0.75 Cu 0.25 Ga 0.05 O 4+δ cathode for IT-SOFCs

In this paper, the B-site cation-excess K 2 NiF 4 -type structure oxide, Pr 2 Ni 0.75 Cu 0.25 Ga 0.05 O 4+δ (PNCG) is investigated as a cathode for intermediate-temperature solid oxide fuel cells (IT-SOFCs). XRD result shows that PNCG cathode is chemically compatible with the electrolyte Gd 0.1 Ce 0.9 O 2-δ (GDC) at 900 °C for 5 h. The PNCG material exhibits a semiconductor to metal transition around 425 °C. The thermal expansion coefficient (TEC) of the PNCG sample is 12.72×10 -6 K -1 between 30 and 850 °C in air. The polarization resistance (R p ) of PNCG cathode on GDC electrolyte is 0.105, 0.197 and 0.300 Ω cm 2 at 800, 750, 700 °C, respectively. A maximum power density of 371 mW cm -2 is obtained at 800 °C for single-cell with 300 μm thick GDC electrolyte and PNCG cathode. Finally, the results of this study demonstrate that PNCG can be a promising cathode material for IT-SOFCs.

36 MATERIALS SCIENCE↗

Cracking vs. surface reactivity in high-nickel cathodes for lithium-ion batteries

High-nickel layered oxide cathodes LiNi x Mn y Co z O 2 (NMC) experience microcracks during cycling. This can expose fresh cathode surfaces for parasitic reactions and isolate active cathode material from the conductive electrode matrix, resulting in impedance increase and capacity fade. The commonly held belief attributes microcracks to anisotropic lattice volume changes of primary particles during cycling. Nevertheless, recent reports suggest that certain electrolytes might reduce microcracks in NMC cathodes during deep cycling. This raises a crucial question on the origin of microcracks: do microcracks exacerbate surface stability, or does poor surface stability contribute to microcrack formation? This perspective aims to provide context and expound this “chicken or egg” dilemma. We contend that the consequence of surface reactivity on the cycle life of high-Ni cathodes is more pronounced than that of particle cracking. Here, we hypothesize that particle cracking is more of a symptom of severe surface reactivity rather than a cause of capacity fade.

25 ENERGY STORAGE↗

Revealing the Structural Evolution and Phase Transformation of O3-Type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 Cathode Material on Sintering and Cycling Processes

O-type layered oxide cathode materials can be easily synthesized for a full sodium stoichiometry with high specific capacity, but they all suffer from a capacity fade on cycling. The sintering process control and optimization are critical to ensure a high quality and consistency of the prepared cathode materials with stable structure. Herein, in situ high-energy X-ray diffraction (HEXRD) was first employed to investigate the phase evolution of the oxides during the sintering process of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 . The in situ HEXRD and both operando Bragg coherent diffraction (BCXD) and coherent multicrystal diffraction (CMCD) were utilized to investigate the phase transformation of the cathode materials during the sodiation/desodiation process. A composite structure comprised of O-type and P-type oxides was formed after the initial electrochemical activation of the cathode material, resulting in good structural and electrochemical stability. This finding implies that strain engineering can be a new design philosophy for the development of next generation high-performance sodium ion cathodes.

25 ENERGY STORAGE↗

Structural Degradation of High Voltage Lithium Nickel Manganese Cobalt Oxide (NMC) Cathodes in Solid-State Batteries and Implications for Next Generation Energy Storage

In this study, we report the stability of the layered high voltage cathode NMC622 with respect to a standard liquid electrolyte and in an all solid-state configuration. NMC622 cathodes with a (104) orientation were found to suffer from degradation at high voltage (4.5 V vs Li/Li + ) due to electrolyte-promoted degradation of the layered structure in a carbonate electrolyte. The lithium phosphorus oxynitride (LiPON) electrolyte was able to suppress the extent of this decomposition in solid-state cells but not totally prevent it from occurring. In the solid-state cells the capacity decreased from 203 to 93 mAh/g in the first cycle and from 93 to 79 mAh/g over the subsequent 99 cycles, whereas, after 20 cycles, the liquid cell charge capacity was dominated by the irreversible electrolyte degradation. Furthermore, the interfacial resistances of the solid-state cells were stable with cycling, suggesting minimal degradation of the NMC622/LiPON interface and incumbent losses due to structural evolution associated with cathode orientation. This data indicates that accessing stable high voltage capacity in NMCs will not be enabled by simply stabilizing the cathode–electrolyte interface. Optimizing cathode crystallographic orientation may be the key to accessing this high voltage regime.

25 ENERGY STORAGE↗

Multifunctional Effect of Fe Substitution in Na Layered Cathode Materials for Enhanced Storage Stability

In this study, developing stable cathode materials that are resistant to storage degradation is essential for practical development and industrial processing of Na-ion batteries, as many sodium layered oxide materials are susceptible to hygroscopicity and instability when exposed to ambient air. Among the various layered compounds, Fe-substituted O 3 -type Na(Ni 1/2 Mn 1/2 ) 1-x Fe x O 2 materials have emerged as a promising option for high-performance and low-cost cathodes. While previous reports have noted the decent air-storage stability of these materials, the role and origin of Fe substitution in improving storage stability remain unclear. In this study, we investigate the air resistant effect of Fe substitution in O 3 -Na(Ni 1/2 Mn 1/2 ) 1-x Fe x O 2 cathode materials by performing systematic surface and structural characterizations. We find that the improved storage stability can be attributed to the multifunctional effect of Fe substitution, which forms a surface protective layer containing an Fe-incorporated spinel phase and decreases the thermodynamical driving force for bulk chemical sodium extraction. With these mechanisms, the Fe-containing cathodes can suppress the cascades of cathode degradation processes and better retain the electrochemical performance after air storage.

25 ENERGY STORAGE↗

Phase Transformation Enables Stable Cycling and Fast Charging of Cation-Disordered Rocksalt Cathodes

Developing high-capacity, long-life cathodes is critical to overcome the energy limitations of current Li-ion batteries. In this work, we report a Li-excess cation-disordered rocksalt (DRX) cathode, Li 1.167 Mn0.7Ti 0.133 O 1.8 F 0.2 (M 0.7 F 0.2 ), which demonstrates excellent electrochemical performance. This cathode delivers a capacity approaching 250 mAh g –1 and maintains 200 mAh g –1 over 200 cycles with an average discharge voltage of 3.1 V at 2 V cutoff. The formation of a spinel-like phase during cycling enables fast charging, achieving over 240 mAh g –1 at 2C for 100 cycles. Combined X-ray absorption spectroscopy and transmission electron microscopy reveal reversible electrochemical redox processes and stable Mn local structures during 2 V discharge. These results highlight the potential of DRX cathodes for next-generation Li-ion batteries and provide insights into strategies to overcome kinetic limitations and optimize the cathode-electrolyte interface.

25 ENERGY STORAGE↗

Carbon fiber paper cathodes for lithium ion batteries

A novel lithium ion battery cathode structure was produced which has the potential for excellent capacity retention and good thermal management. In these cathodes, the active cathode material (lithium iron phosphate) was carbon bonded to a thermally and electrically conductive carbon fiber paper (CFP) support. Electrochemical testing was performed on Swagelok cells consisting of CFP cathodes and lithium anodes. High specific energy, near-theoretical capacity, and good cycling performance were demonstrated for 0.11 mm and 0.37 mm thick CFP cathodes.

74 ATOMIC AND MOLECULAR PHYSICS↗

Functionalization of Cathode–Electrolyte Interface with Ionic Liquids for High-Performance Quasi-Solid-State Lithium–Sulfur Batteries: A Low-Sulfur Loading Study

We introduce a quasi-solid-state electrolyte lithium-sulfur (Li–S) battery (QSSEB) based on a novel Li-argyrodite solid-state electrolyte (SSE), Super P–Sulfur cathode, and Li-anode. The cathode was prepared using a water-based carboxymethyl cellulose (CMC) solution and styrene butadiene rubber (SBR) as the binder while Li6PS5F0.5Cl0.5 SSE was synthesized using a solvent-based process, via the introduction of LiF into the argyrodite crystal structure, which enhances both the ionic conductivity and interface-stabilizing properties of the SSE. Ionic liquids (IL) were prepared using lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as the salt, with pre-mixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent, and they were used to wet the SSE–electrode interfaces. The effect of IL dilution, the co-solvent amount, the LiTFSI concentration, the C rate at which the batteries are tested and the effect of the introduction of SSE in the cathode, were systematically studied and optimized to develop a QSSEB with higher capacity retention and cyclability. Interfacial reactions occurring at the cathode–SSE interface during cycling were also investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and X-ray photoelectron spectroscopy supported by ab initio molecular dynamics simulations. This work offers a new insight into the intimate interfacial contacts between the SSE and carbon–sulfur cathodes, which are critical for improving the electrochemical performance of quasi-solid-state lithium–sulfur batteries.

25 ENERGY STORAGE↗

An In Situ Formed, Dual-Phase Cathode with a Highly Active Catalyst Coating for Protonic Ceramic Fuel Cells

Composite cathodes of solid oxide fuel cells (SOFCs) are normally fabricated by mechanical mixing of electronic- and ionic-conducting phases. Here, a dual-phase SOFC cathode, composed of perovskite PrNi 0.5 Mn 0.5 O 3 (PNM) and exsoluted fluorite PrOx particles, produced in situ through a glycine–nitrate solution combustion process, is reported. When applied as the cathode for a BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3 -based protonic ceramic fuel cell, the hybrid cathode displays excellent electrocatalytic activity (area-specific resistance of 0.052 Ω cm 2 at 700 °C) and remarkable long-term stability when operated at a cell voltage of 0.7 V for ≈500 h using H 2 as fuel and ambient air as oxidant. The excellent performance is attributed to the proton-conducting BaPrO 3 -based coating and high-concentration oxygen vacancies of a Ba-doped PNM surface coating, produced by the reaction between the cathode and Ba from the electrolyte (via evaporation or diffusion), as confirmed by detailed X-ray photoelectron spectroscopy, Raman spectroscopy, and density functional theory-based calculations.

36 MATERIALS SCIENCE↗

In Situ Construction of Uniform and Robust Cathode–Electrolyte Interphase for Li-Rich Layered Oxides

The high-energy-density Li-rich layered oxides (LLOs) as promising cathodes for Li-ion batteries suffer from the dissolution of transition metals (especially manganese) and severe side reactions in conventional electrolytes, which greatly deteriorate their electrochemical performance. Herein, an in situ “anchoring + pouring” synergistic cathode-electrolyte interphase (CEI) construction is realized by using 1,3,6-hexanetricarbonitrile (HTCN) and tris(trimethylsilyl) phosphate (TMSP) electrolyte additives to alleviate the challenges of an LLO (Li 1.13 Mn 0.517 Ni 0.256 Co 0.097 O 2 ). HTCN with three nitrile groups can tightly anchor transition metals by coordinative interaction to form the CEI framework, and TMSP will electrochemically decompose to reshape the CEI layer. The uniform and robust in situ constructed CEI layer can suppress the transition metal dissolution, shield the cathode against diverse side reactions, and significantly improve the overall electrochemical performance of the cathode with a discharge voltage decay of only 0.5 mV/cycle -1 . Further investigations based on a series of experimental techniques and theoretical calculations have revealed the composition of in situ constructed CEI layers and their distribution, including the enhanced HTCN anchoring effect after lattice densification of LLOs. Finally, this study provides insights into the in situ CEI construction for enhancing the performance of high-energy and high-voltage cathode materials through effective, convenient and economical electrolyte approaches.

25 ENERGY STORAGE↗