Search NASA⌕ Search

SEARCH · Search NASA

Results for “Contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Dependence of Carrier Lifetime on Cu-Contacting Temperature and ZnTe:CU Thickness in CdS/CdTe Thin Film Solar Cells

Cu diffusion from a ZnTe:Cu contact interface can increase the net acceptor concentration in the CdTe layer of a CdS/CdTe photovoltaic solar cell. This reduces the space-charge width (W{sub d}) of the junction and enhances current collection and open-circuit voltage. Here we study the effect of Cu concentration in the CdTe layer on carrier lifetime ({tau}) using time-resolved photoluminescence measurements of ZnTe:Cu/Ti-contacted CdTe devices. Measurements show that if the ZnTe:Cu layer thickness remains constant and contact temperature is varied, {tau} increases significantly above its as-deposited value when the contacting temperature is in a range that has been shown to yield high-performance devices ({approx} 280 to {approx} 320 C). However, when the contacting temperature is maintained near an optimum value and the ZnTe:Cu thickness is varied, {tau} decreases with ZnTe:Cu thickness.

14 SOLAR ENERGY↗

Transmission Electron Microscopy Studies of Electron-Selective Titanium Oxide Contacts in Silicon Solar Cells

Abstract In this study, the cross-section of electron-selective titanium oxide (TiO 2 ) contacts for n -type crystalline silicon solar cells were investigated by transmission electron microscopy. It was revealed that the excellent cell efficiency of 21.6% obtained on n -type cells, featuring SiO 2 /TiO 2 /Al rear contacts and after forming gas annealing (FGA) at 350°C, is due to strong surface passivation of SiO 2 /TiO 2 stack as well as low contact resistivity at the Si/SiO 2 /TiO 2 heterojunction. This can be attributed to the transformation of amorphous TiO 2 to a conducting TiO 2- x phase. Conversely, the low efficiency (9.8%) obtained on cells featuring an a-Si:H/TiO 2 /Al rear contact is due to severe degradation of passivation of the a-Si:H upon FGA.

Materials Science↗

Boiling Transitions During Droplet Contact on Superheated Nano/Micro-Structured Surfaces

Manipulating surface topography is one of the most promising strategies for increasing the efficiency of numerous industrial processes involving droplet contact with superheated surfaces. In such scenarios, the droplets may immediately boil upon contact, splash and boil, or could levitate on their own vapor in the Leidenfrost state. In this work we report the outcomes of water droplets coming in gentle contact with designed nano/micro-textured surfaces at a wide range of temperatures as observed using high-speed optical and X-ray imaging. Further, we report a paradoxical increase in the Leidenfrost temperature ($T_{\text{LFP}}$) as the texture spacing is reduced below a critical value (~10 μm) that represents a minima in $T_{\text{LFP}}$. Although droplets on such textured solids appear to boil upon contact, our studies suggest that their behavior is dominated by hydrodynamic instabilities implying that the increase in $T_{\text{LFP}}$ may not necessarily lead to enhanced heat transfer. On such surfaces, the droplets display a new regime characterized by splashing accompanied by a vapor jet penetrating through the droplets before they transition to the Leidenfrost state. We provide a comprehensive map of boiling behavior of droplets over a wide range of texture spacings that may have significant implications towards applications such as electronics cooling, spray cooling, nuclear reactor safety and containment of fire calamities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Implications of Electron Transport Layer and Back Metal Contact Variations in Tin–Lead Perovskite Solar Cells Assessed by Spectroscopic Ellipsometry and External Quantum Efficiency

The structural and optical properties of hybrid organic–inorganic metal halide perovskite solar cells are measured by spectroscopic ellipsometry to reveal an optically distinct interfacial layer among the back contact metal, charge transport, and absorber layers. Understanding how this interfacial layer impacts performance is essential for developing higher performing solar cells. Here, this interfacial layer is modeled by Bruggeman effective medium approximations (EMAs) to contain perovskite, C 60 , BCP, and metal. External quantum efficiency (EQE) simulations that consider scattering, electronic losses, and the formation of nonparallel interfaces are created with input derived from ellipsometry structural-optical models and compared with experimental EQE to estimate optical losses. This nonplanar interface causes optical losses in short circuit current density (JSC) of up to 1.2 mA cm –2 . A study of glass/C 60 /SnO 2 /Ag or Cu and glass/C 60 /BCP/Ag film stacks shows that C 60 and BCP mix, but replacing BCP with SnO 2 can prevent mixing between the ETLs to prevent contact between C 60 and back contact metal and enable the formation of a planar interface between ETLs and back contact metals.

14 SOLAR ENERGY↗

Combinatorial Reactive Sputtering of In2S3 as an Alternative Contact Layer for Thin Film Solar Cells

High-throughput computational and experimental techniques have been used in the past to accelerate the discovery of new promising solar cell materials. An important part of the development of novel thin film solar cell technologies, that is still considered a bottleneck for both theory and experiment, is the search for alternative interfacial contact (buffer) layers. The research and development of contact materials is difficult due to the inherent complexity that arises from its interactions at the interface with the absorber. A promising alternative to the commonly used CdS buffer layer in thin film solar cells that contain absorbers with lower electron affinity can be found in ..beta..-In2S3. However, the synthesis conditions for the sputter deposition of this material are not well-established. Here, In2S3 is investigated as a solar cell contact material utilizing a high-throughput combinatorial screening of the temperature-flux parameter space, followed by a number of spatially resolved characterization techniques. It is demonstrated that, by tuning the sulfur partial pressure, phase pure ..beta..-In2S3 could be deposited using a broad range of substrate temperatures between 500 degrees C and ambient temperature. Combinatorial photovoltaic device libraries with Al/ZnO/In2S3/Cu2ZnSnS4/Mo/SiO2 structure were built at optimal processing conditions to investigate the feasibility of the sputtered In2S3 buffer layers and of an accelerated optimization of the device structure. The performance of the resulting In2S3/Cu2ZnSnS4 photovoltaic devices is on par with CdS/Cu2ZnSnS4 reference solar cells with similar values for short circuit currents and open circuit voltages, despite the overall quite low efficiency of the devices (-2%). Overall, these results demonstrate how a high-throughput experimental approach can be used to accelerate the development of contact materials and facilitate the optimization of thin film solar cell devices.

14 SOLAR ENERGY↗

Daylight-Mediated, Passive, and Sustained Release of the Glaucoma Drug Timolol from a Contact Lens

Timolol, a potent inhibitor of β-adrenergic receptors (βARs), is a first-line drug for decreasing the intraocular pressure (IOP) of patients with glaucoma. Timolol is administered using 0.5% eye-drop solutions at >3 × 10 7 times the inhibitory concentration ( k i ) for βARs. This high dose is wasteful and triggers off-target effects that increase medication noncompliance. Here, we introduce contact lenses that release timolol to the eye throughout the day during passive exposures to natural daylight at a more therapeutically relevant concentration (>3000 k i ). Timolol is coupled to the polymer of the contact lens via a photocleavable caged cross-linker and is released exclusively to the surrounding fluid after the 400-430 nm mediated cleavage of the cross-linking group. Studies conducted in a preclinical mouse model of glaucoma show photoreleased timolol is effective as authentic timolol in reducing IOP. Our studies highlight several advantages of daylight-mediated release of timolol from lenses compared to eye-drops. First, fitted contact lenses exposed to natural daylight release sufficient timolol to sustain the inhibition of βARs over a 10 h period. Second, the contact lenses inhibit βARs in the eye using only 5.7% of the timolol within a single eye-drop. Third, the lenses allow the patient to passively control the amount of timolol released from the lens-for example, early morning exposure to outdoor sunlight would release enough timolol to maximally reduce the IOP, whereas subsequent periodic exposures to indoor daylight would release sufficient timolol to overcome the effects of its spontaneous dissociation from βARs. Fourth, our lenses are disposable, designed for single day use, and manufactured at a low cost.

60 APPLIED LIFE SCIENCES↗

Highly Effective GeNi Alloy Contact Diffusion Barrier for BiSbTe Long-Term Thermal Exposure

A GeNi alloy diffusion barrier for contacts on bismuth antimony telluride is proposed. Multiple gold contact diffusion barriers were tested at different thermal aging conditions in air and reducing atmospheres. Among all diffusion barriers, the GeNi alloy barrier shows the best performance for bulk samples with no substantial degradation of the contact resistance, no contact color change, and no change of thermoelectric properties. We observed D Au–GeNi = (9.8 ± 2.7) × 10 –20 m 2 /s within the GeNi alloy barrier, which is 4 times smaller than D Au–BiSbTe . The presence of the initial Ge layer also proves to be effective in reducing nickel diffusion yielding D Ni–BiSbTe = (8.57 ± 0.49) × 10 –19 m 2 /s. During GeNi alloy formation, Ge diffusion into BiSbTe produces GeTe, which apparently blocks the van der Waals gaps eliminating Au and Ni fast diffusion pathways. Thermal aging of BiSbTe nanowires shows that Au and Ni diffusion degrades the thermoelectric power factor, whereas the GeNi alloy barrier sample is mostly preserved. The GeNi alloy barrier is a reliable solution to long-term thermal applications of BiTe-based materials.

36 MATERIALS SCIENCE↗

Silicon heterojunction solar cells with effectively transparent front contacts

We demonstrate silicon heterojunction solar cells with microscale effectively transparent front contacts (ETCs) that redirect incoming light to the active area of the solar cell. Replacing standard contact electrodes by ETCs leads to an enhancement in short circuit current density of 2.2 mA cm –2 through mitigation of 6% shading losses and improved antireflection layers. ETCs enable low loss lateral carrier transport, with cells achieving an 80.7% fill factor. Furthermore, dense spacing of the contact lines allows for a reduced indium tin oxide thickness and use of non-conductive, optically optimized antireflection coatings such as silicon nitride. We investigated the performance of ETCs under varying light incidence angles, and for angles parallel to the ETC lines find that there is no difference in photocurrent density with respect to bare indium tin oxide layers. In conclusion, for angles perpendicular to the ETC lines, we find that the external quantum efficiency (EQE) always outperforms cells with flat contact grids.

14 SOLAR ENERGY↗

Non-Contact Vapor Detection of Illicit Drugs via Atmospheric Flow Tube-Mass Spectrometry

Real-time, non-contact detection of illicit drugs is a desirable goal for the interdiction of these controlled substances, but the relatively low vapor pressures of such species present a challenge for trace vapor detection technologies. The introduction of atmospheric flow tube-mass spectrometry (AFT-MS), which has previously been demonstrated to detect gas-phase analytes at low parts-per-quadrillion levels for explosives and organophosphorus compounds, also enables the potential for non-contact drug detection. With AFT-MS, direct vapor detection of cocaine and methamphetamine from ~5 µg residues at room temperature is demonstrated herein. Furthermore, thermal desorption of low- to sub-picogram levels of cocaine, methamphetamine, fentanyl, and heroin is observed via AFT-MS using a carrier flow rate of several L/min of air. These low levels can permit non-contact sampling through collection of vapor, effectively preconcentrating the analyte before desorption and analysis. Quantitative evaluation of the thermal desorption approach has yielded limits of detection (LODs) on order of 10 fg for cocaine and fentanyl, 100 fg for methamphetamine, and 1.6 pg for heroin. The LOD for heroin was lowered to 200 fg by using tributyl phosphate as a dopant to form a proton-bound heterodimer with heroin. When used with AFT-MS, the intentional formation of specific drug-dopant adducts has the potential to enhance detection limits and selectivity of additional drug species. Species that are prone to form adducts present a challenge to analysis, but that difficulty can be overcome by the intentional addition of a dopant. Molecules unlikely to form adducts will remain essentially unimpacted, but the adduct-forming species will interact with the dopant to compress the analyte signal into a single peak. This approach would be valuable in the application of non-contact screening for illicit substances via vapor collection followed by thermal desorption for analysis.

methamphetamine, cocaine, heroin, fentanyl, atmosp↗

Study of the Au Schottky contact formation on oxygen plasma treated n-type SnO{sub 2} (101) thin films

As-grown and oxygen plasma treated n-type tin dioxide (SnO{sub 2}) (101) thin films were investigated regarding the properties of Au contacts, surface structure, and band bending. The plasma treatment was performed in a conventional oxygen plasma cleaning system with maximum oxygen ion energies of 400 eV. Whereas the as-deposited SnO{sub 2} film formed non-Schottky contacts with Au, the oxygen plasma treated films formed Schottky contacts with Au. Capacitance-voltage and differential Hall measurements indicated the introduction of bulk electron traps up to several 100 nm below the surface due to the oxygen plasma treatment. Angle resolved x-ray photoelectron spectroscopy (AR-XPS) revealed a surface accumulation layer on the as-grown film that was absent after the plasma treatment. These measurements further revealed chemical differences between the as-deposited and the plasma treated SnO{sub 2} surfaces. All SnO{sub 2} films had Sn{sup 2+}-O bonds. The AR-XPS Sn{sup 2+}-O signal intensity increased after plasma treatment, indicating that the oxygen plasma damaged the SnO{sub 2} surface. Additionally, an O{sub 2} adlayer was formed due to the oxygen plasma treatment. The damaged layer due to oxygen ion bombardment, oxygen adsorption layer, and possibly bulk traps depleted the surface carriers which enabled the formation of a Schottky contact with Au.

36 MATERIALS SCIENCE↗

Calibration of measurement sensitivities of multiple micro-cantilever dynamic modes in atomic force microscopy using a contact detection method

An accurate experimental method is proposed for on-spot calibration of the measurement sensitivities of multiple micro-cantilever dynamic modes in atomic force microscopy. One of the key techniques devised for this method is a reliable contact detection mechanism that detects the tip-surface contact instantly. At the contact instant, the oscillation amplitude of the tip deflection, converted to that of the deflection signal in laser reading through the measurement sensitivity, exactly equals to the distance between the sample surface and the cantilever base position. Therefore, the proposed method utilizes the recorded oscillation amplitude of the deflection signal and the base position of the cantilever at the contact instant for the measurement sensitivity calibration. Experimental apparatus along with various signal processing and control modules was realized to enable automatic and rapid acquisition of multiple sets of data, with which the calibration of a single dynamic mode could be completed in less than 1 s to suppress the effect of thermal drift and measurement noise. Calibration of the measurement sensitivities of the first and second dynamic modes of three micro-cantilevers having distinct geometries was successfully demonstrated. The dependence of the measurement sensitivity on laser spot location was also experimentally investigated. Finally, an experiment was performed to validate the calibrated measurement sensitivity of the second dynamic mode of a micro-cantilever.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Dynamic and impact contact mechanics of geologic materials: Grain-scale experiments and modeling

High fidelity treatments of the generation and propagation of seismic waves in naturally occurring granular materials is becoming more practical given recent advancements in our ability to model complex particle shapes and their mechanical interaction. Of particular interest are the grain-scale processes that are activated by impact events and the characteristics of force transmission through grain contacts. To address this issue, we have developed a physics based approach that involves laboratory experiments to quantify the dynamic contact and impact behavior of granular materials and incorporation of the observed behavior indiscrete element models. The dynamic experiments do not involve particle damage and emphasis is placed on measured values of contact stiffness and frictional loss. The normal stiffness observed in dynamic contact experiments at low frequencies (e.g., 10 Hz) are shown to be in good agreement with quasistatic experiments on quartz sand. The results of impact experiments - which involve moderate to extensive levels of particle damage - are presented for several types of naturally occurring granular materials (several quartz sands, magnesite and calcium carbonate ooids). Implementation of the experimental findings in discrete element models is discussed and the results of impact simulations involving up to 5 Multiplication-Sign 105 grains are presented.

58 GEOSCIENCES↗

Fermi-level depinning and contact resistance reduction in metal/n-Ge junctions by insertion of W-encapsulating Si cluster films

We demonstrate Fermi-level depinning in metal/Ge junctions and a significant reduction of specific contact resistivity of n-Ge by inserting an ultra-thin semiconducting Si-rich W silicide film (WSi{sub n}, n = 12–14) composed of W-encapsulating Si clusters. Dependence of the specific contact resistivity on the electron Schottky barrier height followed the ideal exponential relation for various contact metal species. This result indicates that the insertion of the WSi{sub n} film provides a negligible contribution to contact resistivity because its tunneling resistance is very low owing to the low offset of the conduction band edge of Ge.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Realistic-contact-induced enhancement of rectifying in carbon-nanotube/graphene-nanoribbon junctions

Carbon-nanotube/graphene-nanoribbon junctions were recently fabricated by the controllable etching of single-walled carbon-nanotubes [Wei et al., Nat. Commun. 4, 1374 (2013)] and their electronic transport properties were studied here. First principles results reveal that the transmission function of the junctions show a heavy dependence on the shape of contacts, but rectifying is an inherent property which is insensitive to the details of contacts. Interestingly, the rectifying ratio is largely enhanced in the junction with a realistic contact and the enhancement is insensitive to the details of contact structures. The stability of rectifying suggests a significant feasibility to manufacture realistic all-carbon rectifiers in nanoelectronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Molybdenum as a contact material in zinc tin oxide thin film transistors

Amorphous oxide semiconductors are of increasing interest for a variety of thin film electronics applications. Here, the contact properties of different source/drain electrode materials to solution-processed amorphous zinc tin oxide (ZTO) thin-film transistors are studied using the transmission line method. The width-normalized contact resistance between ZTO and sputtered molybdenum is measured to be 8.7 Ω-cm, which is 10, 20, and 600 times smaller than that of gold/titanium, indium tin oxide, and evaporated molybdenum electrodes, respectively. The superior contact formed using sputtered molybdenum is due to a favorable work function lineup, an insulator-free interface, bombardment of ZTO during molybdenum sputtering, and trap-assisted tunneling. The transfer length of the sputtered molybdenum/ZTO contact is 0.34 μm, opening the door to future radio-frequency sub-micron molybdenum/ZTO thin film transistors.

36 MATERIALS SCIENCE↗

Derivation of a continuum model and the energy law for moving contact lines with insoluble surfactants

A continuous model is derived for the dynamics of two immiscible fluids with moving contact lines and insoluble surfactants based on thermodynamic principles. The continuum model consists of the Navier-Stokes equations for the dynamics of the two fluids and a convection-diffusion equation for the evolution of the surfactant on the fluid interface. The interface condition, the boundary condition for the slip velocity, and the condition for the dynamic contact angle are derived from the consideration of energy dissipations. Different types of energy dissipations, including the viscous dissipation, the dissipations on the solid wall and at the contact line, as well as the dissipation due to the diffusion of surfactant, are identified from the analysis. A finite element method is developed for the continuum model. Numerical experiments are performed to demonstrate the influence of surfactant on the contact line dynamics. The different types of energy dissipations are compared numerically.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Properties and features of structure formation CuCr-contact alloys in electron beam cladding

The microstructure and properties of the contact CuCr alloy produced by electron-beam cladding have been investigated. The effect of the electron beam cladding parameters and preheating temperature of the base metal on the structure and the properties of the coatings has been determined. The bimodal structure of the cladding coating has been established. The short circuit currents tests have been carried out according to the Weil-Dobke synthetic circuit simulating procedure developed for vacuum circuit breakers (VCB) test in real electric circuits. Test results have shown that the electron beam cladding (EBC) contact material has better breaking capacity than that of commercially fabricated sintered contact material. The application of the technology of electron beam cladding for production of contact material would significantly improve specific characteristics and reliability of vacuum switching equipment.

36 MATERIALS SCIENCE↗

Tip-contact related low-bias negative differential resistance and rectifying effects in benzene–porphyrin–benzene molecular junctions

The electronic transport properties of benzene–porphyrin–benzene (BPB) molecules coupled to gold (Au) electrodes were investigated. By successively removing the front-end Au atoms, several BPB junctions with different molecule-electrode contact symmetries were constructed. The calculated current–voltage (I–V) curves depended strongly on the contact configurations between the BPB molecules and the Au electrodes. In particular, a significant low-voltage negative differential resistance effect appeared at −0.3 V in the junctions with pyramidal electrodes on both sides. Along with the breaking of this tip-contact symmetry, the low-bias negative differential resistance effect gradually disappeared. This tip-contact may be ideal for use in the design of future molecular devices because of its similarity with experimental processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗