Search NASA⌕ Search

SEARCH · Search NASA

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Rapidly solidified NiAl and FeAl

Melt spinning was used to produce rapidly solidified ribbons of the B2 intermetallics NiAl and FeAl. Both Fe-40Al and Fe-45Al possessed some bend ductility in the as spun condition. The bend ductility of Fe-40Al, Fe-45Al, and equiatomic NiAl increased with subsequent heat treatment. Heat treatment at approximately 0.85 T (sub m) resulted in significant grain growth in equiatomic FeAl and in all the NiAl compositions. Low bend ductility in both FeAl and NiAl generally coincided with intergranular failure, while increased bend ductility was characterized by increasing amounts of transgranular clevage fracture.

Gaydosh, D. J.↗

High temperature tensile and creep behaviour of low pressure plasma-sprayed Ni-Co-Cr-Al-Y coating alloy

The high temperature tensile and creep behavior of low pressure plasma-sprayed plates of a typical Ni-Co-Cr-Al-Y alloy has been studied. From room temperature to 800 K, the Ni-Co-Cr-Al-Y alloy studied has nearly a constant low ductility and a high strength. At higher temperatures, it becomes weak and highly ductile. At and above 1123 K, the behavior is highly dependent on strain rate and exhibits classic superplastic characteristics with a high ductility at intermediate strain rates and a strain rate sensitivity of about 0.5. At either higher or lower strain rates, the ductility decreases and the strain rate sensitivities are about 0.2. In the superplastic deformation range, the activation energy for creep is 120 + or - 20 kJ/mol, suggesting a diffusion-aided grain boundary sliding mechanism. Outside the superplastic range, the activation energy for creep is calculated to be 290 + or - 20 kJ/mol.

Hebsur, M. G.↗

Structure-property relationships in directionally solidified single crystal NiAl

The ordered intermetallic alloy NiAl is being considered as a potential high temperature structural material, but lack of ductility at ambient temperatures, especially in polycrystalline form, is presently a major obstacle in achieving this goal. Even general agreement of the intrinsic ductility that can be achieved in monocrystals is in dispute. In order to understand this problem, two directionally solidified ingots of NiAl which displayed known differences in ductility were characterized in sufficient detail to identify the corresponding microstructural differences. It was found that the type and size of casting defects, i.e., porosity, present in the material were the major factors in controlling ductility of NiAl single crystals and could explain the order of magnitude variance in fracture strains reported in the literature.

Noebe, R. D.↗

Microstructure and tensile properties of Fe-40 at. pct Al alloys with C, Zr, Hf, and B additions

The influence of small additions of C, Zr, and Hf, alone or in combination with B, on the microstructure and tensile behavior of substoichiometric FeAl was investigated. Tensile properties were determined from 300 to 1100 K on powder which was consolidated by hot extrusion. All materials possessed some ductility at room temperature, although ternary additions generally reduced ductility compared to the binary alloy. Adding B to the C- and Zr-containing alloys changed the fracture mode from intergranular to transgranular and restored the ductility to approximately 5 percent elongation. Additions of Zr and Hf increased strength up to about 900 K. Fe6Al6Zr and Fe6Al6Hf precipitates, both with identical body-centered tetragonal structures, were identified as the principal second phase in these alloys. Strength decreased steadily as temperature increased above 700 K, as diffusion-assisted mechanisms became operative. Although all alloys had similar strengths at 1100 K, Hf additions significantly improved high-temperature ductility by suppressing cavitation.

Gaydosh, D. J.↗

Correlation of deformation mechanisms with the tensile and compressive behavior of NiAl and NiAl(Zr) intermetallic alloys

To identify the mechanisms controlling strength and ductility in powder-extruded NiAl and NiAl + 0.05 at. pct Zr, tensile and compressive testing was performed from 300 to 1300 K for several grain sizes. Grain size refinement significantly increased yield stress in both alloys and, in some cases, slightly lowered the ductile-to-brittle transition temperature (DBTT), although no room-temperature tensile ductility was observed even in the finest grain size specimens. The small Zr addition increased the DBTT and changed the low-temperature fracture mode from intergranular in NiAl to a combination of intergranular and transgranular in the Zr-doped alloy. Scanning electron microscopy of compression specimens deformed at room temperature revealed the presence of grain-boundary cracks in both alloys. These cracks were due to the incompatibility of strain in the polycrystalline material, owing to the lack of five independent slip systems. The tendency to form grain-boundary cracks, in addition to the low fracture stress of these alloys, contributed to the lack of tensile ductility at low temperatures.

Bowman, R. R.↗

The effect of microalloying additions on the tensile properties of polycrystalline NiAl

The presently evaluated 0.1 at. pct Fe and Ga additions to NiAl, while beneficial in the case of monocrystalline NiAl ductility, does not improve ductility in the polycrystalline case; it also has little effect on tensile properties. A similar microalloying addition of Zr, by contrast, significantly depressed the tensile ductility of NiAl, and nearly doubled the brittle-to-ductile transition temperature (BDTT). The dependence of tensile properties on temperature was in all cases similar; tensile elongations remained low and constant until the BDTT was reached, and then dramatically increased.

Noebe, R. D.↗

Neutral Ion Figuring of Chemical Vapor Deposited SiC

Ion figuring of optical components is a relatively new technology that can alleviate some of the problems associated with traditional contact polishing. Because the technique is noncontacting, edge distortions and rib structure print through do not occur. This investigation was aimed at determining the effect of ion figuring on surface roughness of previously polished or ductile ground ceramic optical samples. This is the first step in research directed toward the combination of a prefinishing process (ductile grinding or polishing) with ion figuring to produce finished ceramic mirrors. Multiple, chemical vapor deposited silicon carbide (CVD SiC) samples were polished or ductile ground to specular or near-specular roughness. These samples were then characterized to determine topographic surface information. The surface evaluation consisted of stylus profilometry, interferometry, and optical and scanning electron microscopy. The surfaces were then ion machined to depths from 0 to 5 micron. The finished surfaces were characterized to evaluate the effects of the ion-machining process with respect to the previous processing methods and the preexisting subsurface damage. This study provides some of the information required to effectively utilize a combined ductile grinding or polishing with ion machining as a procedure for figuring optical components.

Fawcett, Steven C.↗

Joining of dissimilar materials

A method of joining dissimilar materials having different ductility, involves two principal steps: Decoration of the more ductile material's surface with particles of a less ductile material to produce a composite; and, sinter-bonding the composite produced to a joining member of a less ductile material. The joining method is suitable for joining dissimilar materials that are chemically inert towards each other (e.g., metal and ceramic), while resulting in a strong bond with a sharp interface between the two materials. The joining materials may differ greatly in form or particle size. The method is applicable to various types of materials including ceramic, metal, glass, glass-ceramic, polymer, cermet, semiconductor, etc., and the materials can be in various geometrical forms, such as powders, fibers, or bulk bodies (foil, wire, plate, etc.). Composites and devices with a decorated/sintered interface are also provided.

36 MATERIALS SCIENCE↗

High power density capacitor and method of fabrication

A ductile preform for making a drawn capacitor includes a plurality of electrically insulating, ductile insulator plates and a plurality of electrically conductive, ductile capacitor plates. Each insulator plate is stacked vertically on a respective capacitor plate and each capacitor plate is stacked on a corresponding insulator plate in alignment with only one edge so that other edges are not in alignment and so that each insulator plate extends beyond the other edges. One or more electrically insulating, ductile spacers are disposed in horizontal alignment with each capacitor plate along the other edges and the pattern is repeated so that alternating capacitor plates are stacked on alternating opposite edges of the insulator plates. A final insulator plate is positioned at an extremity of the preform. The preform may then be drawn to fuse the components and decrease the dimensions of the preform that are perpendicular to the direction of the draw.

42 ENGINEERING↗

Clad fiber capacitor and method of making same

A clad capacitor and method of manufacture includes assembling a preform comprising a ductile, electrically conductive fiber; a ductile, electrically insulating cladding positioned on the fiber; and a ductile, electrically conductive sleeve positioned over the cladding. One or more preforms are then bundled, heated and drawn along a longitudinal axis to decrease the diameter of the ductile components of the preform and fuse the preform into a unitized strand.

36 MATERIALS SCIENCE↗

Clad fiber capacitor and method of making same

A clad capacitor and method of manufacture includes assembling a preform comprising a ductile, electrically conductive fiber; a ductile, electrically insulating cladding positioned on the fiber; a ductile, electrically conductive sleeve positioned over the cladding. One or more of the preforms are then bundled, heated and drawn along a longitudinal axis to decrease the diameter of the ductile components of the preform and fuse the preform into a unitized strand.

42 ENGINEERING↗

First-Principle Calculations on the Structural, Mechanical, and Electronic Properties of Mn{sub 2}RuSi and Mn{sub 2}RuGe Under Pressure

The second- and third-order elastic constants of the new Inverse Heusler compounds Mn{sub 2}RuZ (Z = Si, Ge) are determined from the first-principle calculations combined with homogeneous deformation methods. In terms of the second- and third- order elastic constants, the effective second-order elastic constants of Mn{sub 2}RuZ (Z = Si, Ge) are also presented. Besides, the pressure dependence of the brittle/ductile properties, elastic anisotropy factor, Young’s modulus, and Debye temperature is further investigated. It is found that both Mn{sub 2}RuSi and Mn{sub 2}RuGe display ductile nature at ground state and Mn{sub 2}RuGe has better ductility than Mn{sub 2}RuSi under different pressures. This phenomenon is improved by the Young’s modulus. Finally, the density of states of Mn{sub 2}RuZ (Z = Si, Ge) under different pressures is also calculated in order to reveal the origin of the effect of pressure on the the ductility of Mn{sub 2}RuZ (Z = Si, Ge).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Ti-4Al-1Mn Titanium Alloy

Mechanical behavior of Ti-4Al-1Mn titanium alloy has been studied in annealed, cold-rolled and heat-treated conditions. Room temperature tensile strength as well as % elongation has been found to be low with increasing amount of cold rolling. Lowering of strength in cold worked condition is attributed to premature failure. However, the same has been mitigated after heat treatment. Significant effect of cooling media (air and water) from heat treatment temperature on microstructure was not found except for the degree of fineness of α plates. Optimum properties (strength as well as ductility) were exhibited by samples subjected to 15% cold rolling and heat treatment below β transus temperature, which can be attributed to presence of recrystallized microstructure. In cold worked condition, the microstructure shows fine fragmented α plates/Widmanstätten morphology with high dislocation density along with a large amount of strain fields and twinning, which gets transformed to recrystallized equiaxed microstructure and with plate-like morphology after near β heat treatment. Prior cold work is found to have a significant effect on mechanical properties supported by evolution of microstructure. Twinning is found to be assisting in deformation as well as in recrystallization through the formation of deformation and annealing twins during cold working and heat treatment. Fracture analysis of the tested sample with prior cold work and heat-treated condition revealed quasi-ductile failure as compared to only ductile failure features seen for samples heat treated without prior cold work.

36 MATERIALS SCIENCE↗

Effect of Ceramic Rolling and Annealing on Mechanical Properties of AlCoCrFeNi{sub 2.1} Eutectic High-Entropy Alloys

It was firstly proved that AlCoCrFeNi{sub 2.1} could optimize the strength-ductility combination by ceramic rolling at room temperature. The technique greatly enhanced the strength of the materials at the price of slight ductility, which is different from the previous studies. When the thickness reduction was 23.06%, the yield strength and compressive strength were 1611.42 and 2212.99 MPa, respectively, with the plastic strain of 28.36%. Such an excellent combination of strength and ductility was attributed to the distribution of the residual stress, the high hydrostatic stress and the shear bands in ceramic rolling process. The plastic strain of the material increased to 38.54%, and the strength reduced to 1900.73 MPa after annealing at 800 °C for 1 h. A lot of like-flower patterns of recrystallized ultrafine grain were observed after annealing at 800 °C due to the sluggish diffusion in HEAs and the effect of ceramic rolling. In addition, after annealing at 800 °C, the fracture mode changed to shearing fracture of microvoid aggregation from cleavage/quasi-cleavage fracture of as-rolled sample due to the deposition of the second phase in the tested sample.

36 MATERIALS SCIENCE↗

Processing of Ultrafine-Grained Steels by Warm Rolling and Annealing

Low-carbon microalloyed steel was subjected to warm rolling followed by rapid transformation annealing (RTA) at 800-850 °C and subcritical annealing (SCA) at 600 °C to develop ultrafine ferrite grain structures (UFFG) with grain size less than 3 μm. The present study investigated the influence of light (40%) and heavy (80%) warm rolling deformation (LWR and HWR) applied during the finishing pass of two-pass rolling schedules on the microstructural evolution after rolling and subsequent annealing treatments. RTA treatment of HWR sample at a lower intercritical temperature for an optimum duration (800 °C, 30 s) developed UFFG-martensite dual-phase structure that offered the best combination of strength (YS ~ 900 MPa and UTS ~ 1200 MPa) and ductility (25% elongation). The SCA treatment provided sufficient time to achieve a uniform distribution of carbide particles throughout the ferrite matrix. SCA treatment of HWR at 600 °C for 4 h developed UFFG-carbide structure achieving YS of 800 MPa with 20% ductility. The SCA of LWR resulted in coarser ferrite grain structures (grain size > 5 μm) having higher ductility (more than 30%) but lower strength (UTS of 400-550 MPa) as compared to RTA.

36 MATERIALS SCIENCE↗

Drawing Direction Effect on Microstructure and Mechanical Properties of Twinning-Induced Plasticity Steel During Wire Drawing

The effect of drawing direction on microstructure and mechanical properties in twinning-induced plasticity (TWIP) steel during wire drawing has been investigated to improve drawability for wire rod applications. The steel wires subjected to unidirectional (UD) and reverse-directional (RD) wire drawing were analyzed. The yield and tensile strength processed by the RD were slightly higher than those by the UD, whereas the ductility and drawability have inverse features, which is totally different from the results of plain carbon steel and Al wire. Although final shear strain of wires deformed by the RD is lower than that by the UD, the RD wires had a more complex stress history and a higher <111> texture component at the surface area, which encouraged twinning rate, resulting in fast exhaustion of ductility, finally earlier fracture of wires. In contrast to the materials deformed by mainly slip mechanism, the RD process cannot improve the ductility and drawability in TWIP steel due to the stress state dependency of twinning mechanism. Also, based on the different strengthening behaviors between pearlitic and TWIP steels during UD and RD, it is induced that microstructure and applied stress state simultaneously control the mechanical properties.

36 MATERIALS SCIENCE↗

Microstructures and mechanical properties of Ti-Mo alloys cold-rolled and heat treated

In this study, the microstructures and mechanical properties of Ti-10Mo and Ti-20Mo alloys (mass%) are investigated to assess the potential use in biomedical applications. The microstructures are examined by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). The mechanical properties are determined from uniaxial tensile tests. The experimental results indicate that the microstructures and mechanical properties of Ti-Mo alloys are dependent upon the cold rolling, solution heat treatment, and Mo content. The Ti-10Mo alloy exhibits ({alpha}'' + {beta}) and ({beta} + {omega}) phases under the cold rolling (CR) and solution treatment (ST), respectively. By contrast, the Ti-20Mo alloy comprises only {beta} phase under such conditions. The quenched Ti-20Mo alloy has the lowest elastic modulus and CR Ti-20Mo alloy has the highest tensile strength. The quenched Ti-10Mo alloy exhibits the excellent ductility and two-stage yielding from stress-strain curves due to the stress-induced martensite transformation from {beta} to {alpha}'' during tensile deformation. These Ti-Mo alloys exhibit low yield strength and good ductility, and they are more suitable for biomedical applications than the conventional metallic biomaterials from the viewpoint of better mechanical compatibility. The quenched Ti-10Mo alloy has some advantages over the other {beta} binary Ti-Mo alloys for biomedical applications. {beta} type Ti-Mo-Sn alloys are expected to be promising candidates for novel metallic biomaterials. - Highlights: {yields} The microstructures and mechanical properties of Ti-Mo alloys are dependent upon the cold rolling, solution heat treatment, and Mo content. {yields} The quenched Ti-10Mo alloy exhibits the excellent ductility and two-stage yielding due to stress-induced martensite transformation from beta to alpha double prime during tensile deformation. {yields} The Ti-Mo alloys are more suitable for biomedical applications than the conventional metallic biomaterials from the viewpoint of better mechanical compatibility. {yields} The quenched Ti-10Mo alloy has more advantages over the other beta binary Ti-Mo alloys for biomedical applications.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of Ti-35Nb-6Ta alloy after thermomechanical treatment

The influence of thermo-mechanical treatment on microstructure and mechanical properties of T-35Nb-6Ta has been studied. The thermo-mechanical treatment was chosen to correspond to the production of wire with suitable mechanical properties for dental implants. After casting the alloy was hot forged (700-900 Degree-Sign C), solution treated (850 Degree-Sign C/30 min, water quenched) and cold swaged (reductions up to 91%). The annealing (700 Degree-Sign C/3 h/furnace) or aging (450 Degree-Sign C/8 h/furnace) was used as final heat treatment. The microstructure was studied by using light microscopy, scanning electron microscopy, transmission electron microscopy and XRD analysis. Cold swaging introduces microstructure consisting of highly deformed {beta}-phase grains with dislocation tangles and twins, which ensures high tensile strength about 820 MPa, low Young's modulus ({approx} 50 GPa) and good ductility {approx} 10%. Subsequent aging increases tensile strength (1000 MPa) as well as Young's modulus (75 GPa) without diminishing ductility. Annealing at 700 Degree-Sign C slightly decreases tensile strength (730 MPa) and increases the ductility and Young's modulus (17% and 62 GPa respectively). The mechanical properties attained recommend the thermo-mechanical treatment for production of wires for dental implants. - Highlights: Black-Right-Pointing-Pointer Ti35Nb6Ta alloy prepared via arc melting. Black-Right-Pointing-Pointer Thermo mechanical treatment. Black-Right-Pointing-Pointer Microstructural changes. Black-Right-Pointing-Pointer Mechanical properties.

36 MATERIALS SCIENCE↗