Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW VELOCITY - DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Advantages of the diffuser-augmented wind turbine

Performance optimization for a wind turbine is realized by using a shrouded diffuser to produce up to twice the power of unshrouded turbines of the same diameter. The diffuser converts the kinetic energy of the flow downstream of the rotor into a pressure rise and thus makes it possible for the rotor to capture airflow from a free stream tube area that is greater than that from the rotor itself. The flow velocity through the shrouded rotor is 20 to 60 percent greater than the free wind velocity as opposed to 67 percent less for the unshrouded case. The diffuser also makes it possible to accommodate very high wind speeds without the need of variable pitch in the rotor blades.

Oman, R. A.↗
NASA NTRS1973

Design integration and noise studies for jet STOL aircraft. Task 7A: Augmentor wing cruise blowing valveless system. Volume 1: System design and test integration

Exploratory design studies conducted to establish the configuration of an augmentor wing vruise blowing (valveless) system in a 150-passenger STOL airplane were reported in NASA CR-114570. Those studies have been updated to incorporate the results of static rig, flow duct, and wind tunnel tests. Minor adjustments in duct flow velocity, flap length, and blowing nozzle geometry were incorporated to provide airplane characteristics that minimize takeoff gross weight and achieve sideline noise objectives for an advanced commercial STOL airplane.

Roepcke, F. A.↗
NASA NTRS1974

Bibliography on aircraft fire hazards and safety. Volume 1: Hazards. Part 1: Key numbers 1 to 817

Ignition temperatures of n-hexane, n-octane, n-decane, JP-6 jet fuel, and aircraft engine oil MIL-7-7808 (0-60-18) were determined in air using heated Pyrex cylinders and Nichrome wires, rods, or tubes. Ignition temperature varied little with fuel-air ratio, but increased as the size of the heat source was decreased. Expressions are given which define the variation of the hot surface ignition temperatures of these combustibles with the radius and the surface area of the heat source. The expressions are applicable to stagnant or low velocity flow conditions (less than 0.2 in./sec.). In addition, the hot gas ignition temperatures of the combustible vapor-air mixtures were determined with jets of hot air. These ignition temperatures also varied little with fuel-air ratio and increased as the diameter of the heat sources was decreased.

Pelouch, J. J., Jr.↗
NASA NTRS1974

Some comparisons of the flow characteristics of a turbofan compressor system with and without inlet pressure distortion

The measured effects of a circumferential distortion in inlet total pressure on the fan, low, and high compressor of an afterburning turbofan engine are presented and discussed. Extensive inner-stage instrumentation, combined with a unique test technique offered an accurate means of measuring the shifts in flow, performance, and stall mechanisms within the compressor. These effects are compared at one speed to the corresponding effects measured with undistorted inlet flow. The results show the rate at which the distorted flow areas were attenuated and rotated as well as the change in flow velocities that occurred at various points in the compressor. High response pressure traces indicated the location of stalls including the sequence of dynamic events from the onset and propagation of various stall-recovery events, to compressor surge, to the resulting hammershock.

Evans, D. G.↗
NASA NTRS1974

Development of a miniature solid propellant rocket motor for use in plume simulation studies

A miniature solid propellant rocket motor has been developed to be used in a program to determine those parameters which must be duplicated in a cold gas flow to produce aerodynamic effects on an experimental model similar to those produced by hot, particle-laden exhaust plumes. Phenomena encountered during the testing of the miniature solid propellant motors included erosive propellant burning caused by high flow velocities parallel to the propellant surface, regressive propellant burning as a result of exposed propellant edges, the deposition of aluminum oxide on the nozzle surfaces sufficient to cause aerodynamic nozzle throat geometry changes, and thermal erosion of the nozzle throat at high chamber pressures. A series of tests was conducted to establish the stability of the rocket chamber pressure and the repeatibility of test conditions. Data are presented which define the tests selected to represent the final test matrix. Qualitative observations are also presented concerning the phenomena experienced based on the results of a large number or rocket tests not directly applicable to the final test matrix.

Baran, W. J.↗
NASA NTRS1974

Erosion in radial inflow turbines. Volume 2: Balance of centrifugal and radial drag forces on erosive particles

The particle motion in two-dimensional free and forced inward flowing vortices is considered. A particle in such a flow field experiences a balance between the aerodynamic drag forces that tend to drive erosive particles toward the axis, and centrifugal forces that prevent these particles from traveling toward the axis. Results predict that certain sizes of particles will achieve a stable orbit about the turbine axis in the inward flowing free vortex. In this condition, the radial drag force is equal to the centrifugal force. The sizes of particles that will achieve a stable orbit is shown to be related to the gas flow velocity diagram at a particular radius. A second analysis yields a description of particle sizes that will experience a centrifugal force that is greater than the radial component of the aerodynamic drag force for a more general type of particle motion.

Clevenger, W. B., Jr.↗
NASA NTRS1974

Compressible seal flow analysis using the finite element method with Galerkin solution technique

High pressure gas sealing involves not only balancing the viscous force with the pressure gradient force but also accounting for fluid inertia--especially for choked flow. The conventional finite element method which uses a Rayleigh-Ritz solution technique is not convenient for nonlinear problems. For these problems, a finite element method with a Galerkin solution technique (FEMGST) was formulated. One example, a three-dimensional axisymmetric flow formulation has nonlinearities due to compressibility, area expansion, and convective inertia. Solutions agree with classical results in the limiting cases. The development of the choked flow velocity profile is shown.

Zuk, J.↗
NASA NTRS1973

Nonintrusive dynamic flowmeter

Description of some of the design and performance characteristics of an ultrasonic dynamic flowmeter which combines nonintrusiveness, fast response, high accuracy, and high resolution and is intended for use with cryogenic liquids and water. The flowmeter measures to 1% accuracy the dynamic as well as the steady flow velocity averaged over the pipe area.

Pedersen, N. E.↗
NASA NTRS1974

Some comparisons of the flow characteristics of a turbofan compressor system with and without inlet pressure distortion

The measured effects of a circumferential distortion in inlet total pressure on the fan, low, and high compressor of an afterburning turbofan engine are presented and discussed. Extensive inner-stage instrumentation, combined with a unique test technique offered an accurate means of measuring the shifts in flow, performance, and stall mechanisms within the compressor. These effects are compared at one speed to the corresponding effects measured with undistorted inlet flow. The results show the rate at which the distorted flow areas were attenuated and rotated, as well as the change in flow velocities that occurred at various points in the compressor. High response pressure traces indicated the location of stalls including the sequence of dynamic events from the onset and propagation of various stall-recovery events, to compressor surge, to the resulting hammershock.

Evans, D. G.↗
NASA NTRS1974

Experimental studies on thermodynamic effects of developed cavitation

A method for predicting thermodynamic effects of cavitation (changes in cavity pressure relative to stream vapor pressure) is presented. The prediction method accounts for changes in liquid, liquid temperature, flow velocity, and body scale. Both theoretical and experimental studies used in formulating the method are discussed. The prediction method provided good agreement between predicted and experimental results for geometrically scaled venturis handling four different liquids of widely diverse physical properties. Use of the method requires geometric similarity of the body and cavitated region and a known reference cavity-pressure depression at one operating condition.

Ruggeri, R. S.↗
NASA NTRS1974

The maxometer-dynamic and static tests

The ability to withstand extreme environmental conditions, such as the high flow velocities and extreme temperatures associated with the launch of aerospace vehicles, was considered in the developement of two maxometer models which are capable of measuring extremely high wind speeds (130 m/sec) and retaining a record of the peak speed over any given time period. The dynamic and static tests of these models are reported, along with pertinent results.

Camp, D. W.↗
NASA NTRS1975

Investigation of scrubbing and impingement noise

Tests were conducted in an acoustic wind tunnel to determine surface pressure spectra and far field noise caused by turbulence impinging on an airfoil and turbulence convected past a sharp trailing edge. Measured effects of flow velocity and turbulence intensity were compared with predictions from several theories. Also, tests were conducted in an anechoic chamber to determine surface pressure spectra and far field noise caused by a deflected airfoil scrubbed by a subsonic jet. This installation simulated both an under-the-wing and an upper-surface-blowing externally blown flap, depending on the deflection angle. Surface and far field spectra, and cross correlation coherence and delay time, were utilized to infer the major noise-producing mechanisms.

Fink, M. R.↗
NASA NTRS1975

Evaluation of T-111 forced-convection loop tested with lithium at 1370 C

A T-111 alloy (Ta-8% W-2% Hf) forced-convection loop containing molten lithium was operated 3000 hr at a maximum temperature of 1370 C. Flow velocities up to 6.3 m/sec were used, and the results of this forced-convection loop are very similar to those observed in lower velocity thermal-convection loops of T-111 containing lithium. Weight changes were determined at 93 positions around the loop. The maximum dissolution rate occurred at the maximum wall temperature of the loop and was less than 1.3 microns/year. Mass transfer of hafnium, nitrogen, and, to a lesser extent, carbon occurred from the hotter to cooler regions. Exposed surfaces in the highest temperature region were found to be depleted in hafnium to a depth of 60 microns with no detectable change in tungsten content. There was some loss in room-temperature tensile strength for specimens exposed to lithium at 1370 C, attributable to depletion of hafnium and nitrogen and to attendant grain growth.

Devan, J. H.↗
NASA NTRS1975

An approximate closed-form solution for lead lag damping of rotor blades in hover

Simple stability methods are used to derive an approximate, closed-form expression for the lead-lag damping of rotor blades in hover. Destabilizing terms are shown to be a result of two dynamic mechanisms. First, the destabilizing aerodynamic forces that can occur when blade lift is higher than a critical value are maximized when the blade motion is in a straight line equidistant from the blade chord and the average direction of the air flow velocity. This condition occurs when the Coriolis terms vanish and when the elastic coupling terms align the blade motion with this least stable direction. Second, the nonconservative stiffness terms that result from pitch-flap or pitch-lag coupling can add or subtract energy from the system depending upon whether the motion of the blade tip is clockwise or counterclockwise.

Peters, D. A.↗
NASA NTRS1975

Effect of a 180 deg-extent inlet pressure distortion on the internal flow conditions of a TF30-P-3

The measured effects of inlet pressure distortion on the internal flow temperatures and pressures of a TF30-P-3 afterburning turbofan engine are reported. Extensive inner-stage instrumentation combined with stepwise rotation of pressure distortion provided a high degree of circumferential resolution in the data. The steady-state spatial variation in pressures, temperature, and calculated flow velocity and the amplitude and extent of the distorted sectors are given. Data are presented for runs of 77 and 90 percent of low-speed-rotor design speed at pressure distortion levels two-thirds of that required to stall the engine. These data are compared with data taken at clean-inlet conditions. Results indicate that the inlet pressure distortion was quickly attenuated within the compressor, except at the hub of the low-pressure compressor. The distorted sectors also swirled and varied in extent as they passed through the engine. Average velocities within the compressor were about equal to the clean-inlet values.

Debogdan, C. E.↗
NASA NTRS1975

Lines, connectors, joints, and fittings

The structural reliability of lines, connectors, joints, and fittings used in liquid and gaseous O2 systems was examined. Overstress and high velocity flow of gaseous O2 as they affect system failure are also examined. Special attention was given to efforts to determine factors for designing a reliable O2 transport system for operation at all possible pressures.

Source record↗
NASA NTRS1974

Erosion by catastrophic floods on Mars and Earth

The morphologic features of the large Martian channels are shown to be strikingly similar to those of the Channeled Scabland of eastern Washington, produced by the catastrophic breakout floods of Pleistocene Lake Missoula. If the analogy is correct, floods involving water discharges of millions of cubic meters per second and peak flow velocities of tens of meters per second, but perhaps lasting no more than a few days, may have occurred on Mars.

Baker, V. R.↗
NASA NTRS1975

A model of the Venus ionosphere

Results of model calculations of the Venus ionosphere from 120 to 300 km are presented. The chemical scheme and reaction rates used are the same as given by Kumar and Hunten (1974) except that the electron temperature dependence of the dissociative recombination rates is taken into account. Calculations are made for low and high atomic oxygen models in which the O/CO2 ratios are 0.4% and 4% respectively at 140 km, and the results agree well in shape and magnitude with the Mariner 5 and 10 occultation results in the chemically controlled region. Reasonable agreement is obtained at higher altitudes if diffusive equilibrium and high vertical flow velocities (10 km/s) are assumed as upper boundaries for the Mariner 5 and 10 conditions respectively, although solar wind-ionosphere interactions are considered to be the controlling mechanism for the Mariner 10 results.

Nagy, A. F.↗