Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inflatable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Deployable Aeroshell Flexible Thermal Protection System Testing

Deployable aeroshells offer the promise of achieving larger aeroshell surface areas for entry vehicles than otherwise attainable without deployment. With the larger surface area comes the ability to decelerate high-mass entry vehicles at relatively low ballistic coefficients. However, for an aeroshell to perform even at the low ballistic coefficients attainable with deployable aeroshells, a flexible thermal protection system (TPS) is required that is capable of surviving reasonably high heat flux and durable enough to survive the rigors of construction handling, high density packing, deployment, aerodynamic loading and aerothermal heating. The Program for the Advancement of Inflatable Decelerators for Atmospheric Entry (PAIDAE) is tasked with developing the technologies required to increase the technology readiness level (TRL) of inflatable deployable aeroshells, and one of several of the technologies PAIDAE is developing for use on inflatable aeroshells is flexible TPS. Several flexible TPS layups were designed, based on commercially available materials, and tested in NASA Langley Research Center's 8 Foot High Temperature Tunnel (8ft HTT). The TPS layups were designed for, and tested at three different conditions that are representative of conditions seen in entry simulation analyses of inflatable aeroshell concepts. Two conditions were produced in a single run with a sting-mounted dual wedge test fixture. The dual wedge test fixture had one row of sample mounting locations (forward) at about half the running length of the top surface of the wedge. At about two thirds of the running length of the wedge, a second test surface drafted up at five degrees relative to the first test surface established the remaining running length of the wedge test fixture. A second row of sample mounting locations (aft) was positioned in the middle of the running length of the second test surface. Once the desired flow conditions were established in the test section the dual wedge test fixture, oriented at 5 degrees angle of attack down, was injected into the flow. In this configuration the aft sample mounting location was subjected to roughly twice the heat flux and surface pressure of the forward mounting location. The tunnel was run at two different conditions for the test series: 1) 'Low Pressure', and 2) 'High Pressure'. At 'Low Pressure' conditions the TPS layups were tested at 6W/cm2 and 11W/cm2 while at 'High Pressure' conditions the TPS layups were tested at 11W/cm2 and 20W/cm2. This paper details the test configuration of the TPS samples in the 8Ft HTT, the sample holder assembly, TPS sample layup construction, sample instrumentation, results from this testing, as well as lessons learned.

Hughes, Stephen J.↗

Safe, Advanced, Adaptable Isolation System Eliminates the Need for Critical Lifts

The Starr Soft Support isolation system incorporates an automatically reconfigurable aircraft jack into NASA's existing 1-Hertz isolators. This enables an aircraft to float in mid-air without the need for a critical lift during ground vibration testing (GVT), significantly reducing testing risk, time, and costs. Currently incorporating the most advanced technology available, the 60,000-poundcapacity (27-metric-ton) isolation system is used for weight and measurement tests, control-surface free-play tests, and structural mode interaction tests without the need for any major reconfiguration, often saving days of time and significantly reducing labor costs. The Starr Soft Support isolation system consists of an aircraft-jacking device with three jacking points, each of which has an individual motor and accommodates up to 20,000 pounds (9 metric tons) for a total 60,000-pound (27-metric-ton) capacity. The system can be transported to the aircraft by forklift and placed at its jacking points using a pallet jack. The motors power the electric actuators, raising the aircraft above the ground until the landing gear can retract. Inflatable isolators then deploy, enabling the aircraft to float in mid-air, simulating a 1-Hertz free-free boundary condition. Inflatable isolators have been in use at NASA for years, enabling aircraft to literally float unsupported for highly accurate GVT. These isolators must be placed underneath the aircraft for this to occur. Traditionally, this is achieved by a critical lift a high-risk procedure in which a crane and flexible cord system are used to lift the aircraft. In contrast, the Starr Soft Support isolation system eliminates the need for critical lift by integrating the inflatable isolators into an aircraft jacking system. The system maintains vertical and horizontal isolating capabilities. The aircraft can be rolled onto the system, jacked up, and then the isolators can be inflated and positioned without any personnel needing to work underneath the aircraft. Also, the system accommodates changes in aircraft configuration, automatically adapting to changes in mass, and it can adjust the height of the isolators in one basic setup. Dryden personnel used the Starr Soft Support system to successfully perform a GVT on an F-15 being structurally modified by Gulfstream, Dryden's Gulfstream III used for science research and the crew exploration module and adaptor cone assembly.

Ginn, Starr↗

Surface Textures and Features Indicative of Endogenous Growth at the McCartys Flow Field, NM, as an Analog to Martian Volcanic Plains

Basaltic lavas typically form channels or tubes, which are recognized on the Earth and Mars. Although largely unrecognized in the planetary community, terrestrial inflated sheet flows also display morphologies that share many commonalities with lava plains on Mars. The McCartys lava flow field is among the youngest (approx.3000 yrs) basaltic flows in the continental United States. The southwest sections of the flow displays smooth, flat-topped plateaus with irregularly shaped pits and hummocky inter-plateau units that form a polygonal surface. Plateaus are typically elongate in map view, up to 20 m high and display lineations within the glassy crust. Lineated surfaces occasionally display small < 1m diameter lava coils. Lineations are generally straight and parallel each other, sometimes for over 100 meters. The boundaries between plateaus and depressions are also lineated and tilted to angles sometimes approaching vertical. Plateau-parallel cracks, sometimes containing squeeze-ups, mark the boundary between tilted crust and plateau. Some plateau depressions display level floors with hummocky surfaces, while some are bowl shaped with floors covered in broken lava slabs. The lower walls of pits sometimes display lateral, sagged lava wedges. Infrequently, pit floors display the upper portion of a tumulus from an older flow. In some places the surface crust has been disrupted forming a slabby texture. Slabs are typically on the scale of a meter or less across and no less than 7-10 cm thick. The slabs preserve the lineated textures of the undisturbed plateau crust. It appears that this style of terrain represents the emplacement of an extensive sheet that experiences inflation episodes within preferred regions where lateral spreading of the sheet is inhibited, thereby forming plateaus. Rough surfaces represent inflation-related disruption of pahoehoe lava and not a a lava. Depressions are often the result of non-inflation and can be clearly identified by lateral squeeze-outs along the pit walls that form when the rising crust exposes the still liquid core of the sheet. The plains of Tharsis and Elysium, Mars, display many analogous features

Bleacher, Jacob E.↗

Skipped Stage Modeling and Testing of the CPAS Main Parachutes

The Capsule Parachute Assembly System (CPAS) has undergone the transition from modeling a skipped stage event using a simulation that treats a cluster of parachutes as a single composite canopy to the capability of simulating each parachute individually. This capability along with data obtained from skipped stage flight tests has been crucial in modeling the behavior of a skipping canopy as well as the crowding effect on non-skipping ("lagging") neighbors. For the finite mass inflation of CPAS Main parachutes, the cluster is assumed to inflate nominally through the nominal fill time, at which point the skipping parachute continues inflating. This sub-phase modeling method was used to reconstruct three flight tests involving skipped stages. Best fit inflation parameters were determined for both the skipping and lagging canopies.

Varela, Jose G.↗

Lightweight Solar Power for Small Satellites

The innovation targets small satellites or CubeSats for which conventional deployable arrays are not feasible due to their size, weight and complexity. This novel solar cell array includes a thin and flexible photovoltaic cell applied to an inflatable structure to create a high surface area array for collecting solar energy in a lightweight, simple and deployable structure. The inflatable array, with its high functional surface area, eliminates the need and the mechanisms required to point the system toward the sun. The power density achievable in these small arrays is similar to that of conventional high-power deployable/pointable arrays used on large satellites or space vehicles. Although inflatable solar arrays have been previously considered by others, the arrays involved the use of traditional rigid solar cells. Researchers are currently working with thin film photovoltaics from various suppliers so that the NASA innovation is not limited to any particular solar cell technology. NASA has built prototypes and tested functionality before and after inflation. As shown in the current-voltage currents below, deployment does not damage the cell performance.

Nabors, Sammy A.↗

Thermal Design and Analysis of the Supersonic Flight Dynamics Test Vehicle for the Low Density Supersonic Decelerator Project

The thermal design and analysis of the experimental Supersonic Flight Dynamics Test (SFDT) vehicle is presented. The SFDT vehicle is currently being designed as a platform to help demonstrate key technologies for NASA's Low Density Supersonic Decelerator (LDSD) project. The LDSD project is charged by NASA's Office of the Chief Technologist (OCT) with the task of advancing the state of the art in Mars Entry, Descent, and Landing (EDL) systems by developing and testing three new technologies required for landing heavier payloads on Mars. The enabling technologies under development consist of a large 33.5 meter diameter Supersonic Ringsail (SSRS) parachute and two different types of Supersonic Inflatable Aerodynamic Decelerator (SIAD) devices - a robotic class, SIAD-R, that inflates to a 6 meter diameter torus, and an exploration class, SIAD-E, that inflates to an 8 meter diameter isotensoid. As part of the technology development effort, the various elements of the new supersonic decelerator system must be tested in a Mars-like environment. This is currently planned to be accomplished by sending a series of SFDT vehicles into Earth's stratosphere. Each SFDT vehicle will be lifted to a stable float altitude by a large helium carrier balloon. Once at altitude, the SFDT vehicles will be released from their carrier balloon and spun up via spin motors to provide trajectory stability. An onboard third stage solid rocket motor will propel each test vehicle to supersonic flight in the upper atmosphere. After main engine burnout, each vehicle will be despun and testing of the deceleration system will begin: first an inflatable decelerator will be deployed around the aeroshell to increase the drag surface area, and then the large parachute will be deployed to continue the deceleration and return the vehicle back to the Earth's surface. The SFDT vehicle thermal system must passively protect the vehicle structure and its components from cold temperatures experienced during the ascent phase of the mission as well as from the extreme heat fluxes produced during the supersonic test phase by the main motor plume and aeroheating. The passive thermal design approach for the SFDT vehicle relies upon careful and complex bounding analysis of all three modes of heat transfer - conduction, convection, and radiation - coupled with a tightly managed transient power dissipation timeline for onboard electronics components throughout all mission phases.

thermal desktop↗

HIAD on ULA (HULA) Orbital Reentry Flight Experiment Concept

This paper describes a proposed orbital velocity reentry flight test of a Hypersonic Inflatable Aerodynamic Decelerator (HIAD). The flight test builds upon ground development activities that continue to advance the materials, design, and manufacturing techniques for the inflatable structure and flexible thermal protection system (F-TPS) that comprise the inflatable heat shield. While certain aspects of material and system performance can be assessed using a variety of ground testing capabilities, only orbital velocity energy on a trajectory through the gradient density of the atmosphere can impart the combined aerodynamic and aeroheating design environments in real time. To achieve this at limited cost, the HIAD would be delivered to a spin-stabilized entry trajectory as a secondary payload on the Centaur stage of a United Launch Alliance (ULA) Atlas V launch vehicle. Initial trajectory studies indicate that the combination of launch vehicle capability and achievable reentry vehicle ballistic numbers make this a strategic opportunity for technology development. This 4 to 6 meter diameter scale aeroshell flight, referred to as HIAD on ULA (HULA), would also contribute to ULA asset recovery development. ULA has proposed that a HIAD be utilized as part of the Sensible, Modular, Autonomous Return Technology (SMART) initiative to enable recovery of the Vulcan launch vehicle booster main engines [1], including a Mid-Air Recovery (MAR) to gently return these assets for reuse. Whereas HULA will attain valuable aerothermal and structural response data toward advancing HIAD technology, it may also provide a largest-to-date scaled flight test of the MAR operation, which in turn would allow the examination of a nearly pristine post-entry aeroshell. By utilizing infrared camera imaging, HULA will also attain aft-side thermal response data, enhancing understanding of the aft side aerothermal environment, an area of high uncertainty. The aeroshell inflation will utilize a heritage design compressed gas system to minimize development costs. The data will be captured to both an onboard recorder and a recorder that is jettisoned and recovered separately from the reentry vehicle to mitigate risk. This paper provides an overview, including the architecture and flight concept of operations, for the proposed HULA flight experiment.

Dinonno, J. M.↗

Fabrication of the HIAD Large-Scale Demonstration Assembly and Upcoming Mission Applications

Over a decade of work has been conducted in the development of NASAs Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. This effort has included multiple ground test campaigns and flight tests culminating in the HIAD projects second generation (Gen-2) deployable aeroshell system and associated analytical tools. NASAs HIAD project team has developed, fabricated, and tested inflatable structures (IS) integrated with flexible thermal protection system (F-TPS), ranging in diameters from 3-6m, with cone angles of 60 and 70 deg.In 2015, United Launch Alliance (ULA) announced that they will use a HIAD (10-12m) as part of their Sensible, Modular, Autonomous Return Technology (SMART) for their upcoming Vulcan rocket. ULA expects SMART reusability, coupled with other advancements for Vulcan, will substantially reduce the cost of access to space. The first booster engine recovery via HIAD is scheduled for 2024. To meet this near-term need, as well as future NASA applications, the HIAD team is investigating taking the technology to the 10-15m diameter scale.In the last year, many significant development and fabrication efforts have been accomplished, culminating in the construction of a large-scale inflatable structure demonstration assembly. This assembly incorporated the first three tori for a 12m Mars Human-Scale Pathfinder HIAD conceptual design that was constructed with the current state of the art material set. Numerous design trades and torus fabrication demonstrations preceded this effort. In 2016, three large-scale tori (0.61m cross-section) and six subscale tori (0.25m cross-section) were manufactured to demonstrate fabrication techniques using the newest candidate material sets. These tori were tested to evaluate durability and load capacity. This work led to the selection of the inflatable structures third generation (Gen-3) structural liner. In late 2016, the three tori required for the large-scale demonstration assembly were fabricated, and then integrated in early 2017. The design includes provisions to add the remaining four tori necessary to complete the assembly of the 12m Human-Scale Pathfinder HIAD in the event future project funding becomes available.This presentation will discuss the HIAD large-scale demonstration assembly design and fabrication per-formed in the last year including the precursor tori development and the partial-stack fabrication. Potential near-term and future 10-15m HIAD applications will also be discussed.

Swanson, G. T.↗

Fabrication of the HIAD Large-Scale Demonstration Assembly

Over a decade of work has been conducted in the development of NASA's Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. This effort has included multiple ground test campaigns and flight tests culminating in the HIAD projects second generation (Gen-2) deployable aeroshell system and associated analytical tools. NASAs HIAD project team has developed, fabricated, and tested inflatable structures (IS) integrated with flexible thermal protection system (F-TPS), ranging in diameters from 3-6m, with cone angles of 60 and 70 deg.In 2015, United Launch Alliance (ULA) announced that they will use a HIAD (10-12m) as part of their Sensible, Modular, Autonomous Return Technology (SMART) for their upcoming Vulcan rocket. ULA expects SMART reusability, coupled with other advancements for Vulcan, will substantially reduce the cost of access to space. The first booster engine recovery via HIAD is scheduled for 2024. To meet this near-term need, as well as future NASA applications, the HIAD team is investigating taking the technology to the 10-15m diameter scale. In the last year, many significant development and fabrication efforts have been accomplished, culminating in the construction of a large-scale inflatable structure demonstration assembly. This assembly incorporated the first three tori for a 12m Mars Human-Scale Pathfinder HIAD conceptual design that was constructed with the current state of the art material set. Numerous design trades and torus fabrication demonstrations preceded this effort. In 2016, three large-scale tori (0.61m cross-section) and six subscale tori (0.25m cross-section) were manufactured to demonstrate fabrication techniques using the newest candidate material sets. These tori were tested to evaluate durability and load capacity. This work led to the selection of the inflatable structures third generation (Gen-3) structural liner. In late 2016, the three tori required for the large-scale demonstration assembly were fabricated, and then integrated in early 2017. The design includes provisions to add the remaining four tori necessary to complete the assembly of the 12m Human-Scale Pathfinder HIAD in the event future project funding becomes available.This presentation will discuss the HIAD large-scale demonstration assembly design and fabrication per-formed in the last year including the precursor tori development and the partial-stack fabrication. Potential near-term and future 10-15m HIAD applications will also be discussed.

Swanson, G. T.↗

Aerodynamic Coefficients from Aeroballistic Range Testing of Deployed- and Stowed-SIAD SFDT Models

This report documents a ballistic-range test campaign conducted in 2012 in order to estimate the aerodynamic stability characteristics of two configurations of the Supersonic Flight Dynamics Test (SFDT) vehicle prior to its initial flight in 2014. The SFDT vehicle was a test bed for demonstrating several new aerodynamic decelerator technologies then being developed under the Low-Density Supersonic Decelerator (LDSD) Project. Of particular interest here is the Supersonic Inflatable Aerodynamic Decelerator (SIAD), an inflatable attached torus used to increase the drag surface area of an entry vehicle during the supersonic portion of the entry trajectory. Two model configurations were tested in the ballistic range: one representing the SFDT vehicle prior to deployment of the SIAD, and the other representing the nominal shape with the SIAD inflated. Both models were fabricated from solid metal, and therefore, the effects of the flexibility of the inflatable decelerator were not considered. The test conditions were chosen to match, as close as possible, the Mach number, Reynolds number, and motion dynamics expected for the SFDT vehicle in flight, both with the SIAD stowed and deployed. For SFDT models with the SIAD stowed, 12 shots were performed covering a Mach number range of 3.2 to 3.7. For models representing the deployed SIAD, 37 shots were performed over a Mach number range of 2.0 to 3.8. Pitch oscillation amplitudes covered a range from 0.7 to 20.6 degrees RMS. Portions of this report (data analysis approach, aerodynamic modeling, and resulting aerodynamic coefficients) were originally published as an internal LDSD Project report [1] in 2012. In addition, this report provides a description of the test design approach, the test facility, and experimental procedures. Estimated non-linear aerodynamic coefficients, including pitch damping, for both model configurations are reported, and the shot-by-shot trajectory measurements, plotted in comparison with calculated trajectories based on the derived non-linear aerodynamic coefficients, are provided as appendices. Since the completion of these tests, two full-scale SFDT flights have been successfully conducted: one in June 2014 [2, 3], and one in June 2015 [3].

Ground Test↗

A Momentum-Based Indicator for Predicting the Peak Opening Load of Supersonic Parachutes

In this paper, a new empirical indicator for predicting the peak opening loads of supersonic parachutes is presented. The proposed indicator is proportional to twice the free-stream dynamic pressure and the projected area of the parachute, which is equivalent to estimating the opening load as a percentage of the free-stream momentum flux through the projected area at the moment of peak inflation. The form of this expression is motivated by a classical control volume analysis of the aerodynamic forces acting on a parachute during inflation, under the simplifying assumptions of quasi-static and one-dimensional flow. For parachute geometries and flight conditions typical of Mars Entry, Descent, and Landing systems, the largest contribution to the total drag is shown to be a momentum flux term that is associated with the entrainment of atmosphere within the inflating parachute volume. Using this new method, empirical constants are calculated from existing flight reconstruction data and are shown to have a smaller standard deviation than similar constants determined using the customary indicator form, which is based on the steady-state subsonic drag and proportional to the parachute reference area. These empirical constants are also compared to an analytic estimate, derived from the control volume analysis, and shown to have excellent agreement across a wide range of Mach numbers and dynamic pressures for several parachute geometries. While opening loads estimated using both methods produce similar results at low supersonic Mach numbers typical of past inflations, the proposed method predicts notably larger loads at higher Mach numbers, those above Mach 2.0, due to the omission of any Mach Efficiency Factor. Several current Mars EDL projects have adopted this new indicator.

Way, David W.↗

ASPIRE Aerodynamic Models and Flight Performance

NASA's Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project was established to test full-scale supersonic parachutes at Mars-relevant conditions, as a risk-reduction activity for NASA's upcomingMars2020 mission. Deployment and inflation of Disk-Gap-Band (DGB) parachutes were examined at Mach number and dynamic pressure conditions relevant to Mars2020, using a sounding rocket platform. The flight tests examined two parachutes: a build-to-print version of the parachute used by the Mars Science Laboratory and a strengthened version of this parachute that has the same geometry but differs in materials and construction. The first flight test (SR01) of the built-to-print parachute took place on October 4, 2017, followed by the first test of the strengthened parachute during flight SR02 on March 31, 2018. A second test of the strengthened parachute with a higher target load, SR03, took place on September 7, 2018. Over the sequence of the three tests, the parachute was exposed to increasing aerodynamic loads with the peak load during SR03 being significantly larger than is expected during a Martian descent. All three tests were successful: the parachute deployment and inflation occurred at the intended conditions, the measurement systems performed as designed and provided the data, and the parachutes survived the aerodynamic loads they were exposed to. The flight tests yielded valuable data on parachute forces and high-speed imagery of the deployment and inflation process.

Parachute↗

Underlying Fundamentals of Kalman Filtering for River Network Modeling

The grand challenge of producing hydrometeorological estimates every time and everywhere has motivated the fusion of sparse observations with dense numerical models, with a particular interest on discharge in river modeling. Ensemble methods are largely preferred as they enable the estimation of error properties, but at the expense of computational load and generally with underestimations. These imperfect stochastic estimates motivate the use of correction methods, that is, error localization and inflation, although the physical justifications for their optimality are limited. The purpose of this study is to use one of the simplest forms of data assimilation when applied to river modeling and reveal the underlying mechanisms impacting its performance. Our framework based on assimilating daily averaged in situ discharge measurements to correct daily averaged runoff was tested over a 4-yr case study of two rivers in Texas. Results show that under optimal conditions of inflation and localization, discharge simulations are consistently improved such that the mean values of Nash–Sutcliffe efficiency are enhanced from211.32 to 0.55 at observed gauges and from212.24 to21.10 at validation gauges. Yet, parameters controlling the inflation and the localization have a large impact on the performance. Further investigations of these sensitivities showed that optimal inflation occurs when compensating exactly for discrepancies in the magnitude of errors while optimal localization matches the distance traveled during one assimilation window. These results may be applicable to more advanced data assimilation methods as well as for larger applications motivated by upcoming river-observing satellite missions, such as NASA’s Surface Water and Ocean Topography mission.

Streamflow↗

NASA's Habitation Development Status: Current Concepts and ISRU Opportunities

Introduction: The National Aeronautics and Space Administration (NASA) is embarking on a bold journey to return humankind to the Moon and onward to Mars with innovative commercial, international, and academic partnerships [1]. Under the Artemis series of missions, NASA seeks to establish sustained human exploration of deep space through an objectives-based approach [2]. This approach drives the identification of needed system functionality and the current and future capabilities which will eventually allow humanity to sustainably live beyond Earth. Providing evolvable and scalable habitation is a cornerstone function that calls for the collection and integration of current, developmental, and future technologies that can meet near-term exploration needs while growing into long-term sustained presence. NASA is advancing in-space habitation through its Next Space Technologies for Exploration Partnerships (NextSTEP) model while designing lunar, Mars transit, and Mars surface habitat government reference concepts for Artemis missions. These efforts have unveiled possible near-term opportunities for the in-space resource utilization community if human habitation is considered a future customer of space resources. NextSTEP Habitation Development: NASA is closely working with commercial partners under its NextSTEP Appendix A model to advance habitation systems in the arena of inflatable and composite habitation structures. Such efforts promise efficiencies in volumetric packaging and overall spacecraft mass respectively. Recent testing by commercial partners have helped to quantify possible failure mechanisms for inflatable structures while advancing their technology towards eventual flight certification. The advancement of such Class II habitation structures, in which the habitat is only fully deployed once in-space or on a planetary surface [3], is critical to providing increased habitable volume for long-duration missions with no additional mass penalties. The progression of such technology is infused into NASA’s government reference concepts for notional deep space habitation concepts. Current Government Reference Concepts: To best inform the formulation of future collaborative solicitations, NASA employs the practice of internally developing reference concepts for future exploration elements. These concepts aid in identifying the functions and capabilities needed to complete NASA missions as well as feasible solutions within the timeframe needed. Government reference concepts for a lunar Surface Habitat, Mars Transit Habitat, and Mars Sur-face Habitat are continuously being developed and updated to better guide the Agency’s overall exploration architecture. Lunar Surface Habitat. As NASA returns to the Moon, it is evaluating possible lunar surface habitation concepts. The Surface Habitat (SH) reference concept entails a hybrid metallic-inflatable structure capable of initially housing two crew for surface stays of up to 30 days in duration [4]. While initial missions may span ~7 days in duration, consideration is being given to expanding SH’s capability to support a crew of four for up to 60 days over its 15-year design life [5]. Functionally, the SH serves as a ‘hub’ for all Artemis crewed surface operations, providing internal volume for maintenance, medical, logistics, science utilization, and extravehicular activity (EVA) support in addition to core habitation functionality such as environmental control and life support (ECLS) and power generation and distribution among many others. Additionally, NASA has entered a study agreement with the Italian Space Agency (Agenzia Spaziale Italiana – ASI) to investigation a possible Multi-Purpose Habitat (MPH) as an additional or augmenting habit-able element for the lunar surface [6]. Mars Transit Habitat. NASA’s current architectural concept for initial human missions to Mars entails the utilization of a transit habitat (TH) to transport a four-person crew to and from Mars orbit, departing from and returning to a lunar near-rectilinear halo orbit (NRHO), over the course of a ~1,200-day mission [5]. While holding a similar 15-year design lifetime, TH will also support a series of analog mission activities in NRHO to gradually test the systems and interaction with lunar surface elements, some of which may be adapted for Mars surface exploration. Holding similar functional capabilities as SH, TH is sized to support much longer durations in space and greater logistical independence. Mars Surface Habitat. NASA is still exploring the concept of operations for initial crewed missions to Mars. As such, the Mars Surface Habitat (MSH) concept is still in its infancy as options for mobile, pressurized habitation and stationary habitats are being explored. It is expected MSH will leverage heavily from the lunar SH and possible lunar pressurized rover, however the very different Martian environment will likely necessitate modifications. ISRU Opportunities: Despite the advancements under NASA’s NextSTEP habitation work and continually optimized reference concepts, NASA is facing near-term mass and power challenges that may create opportunities to the ISRU community by providing yet another possible customer for space resources. While NASA desires to use regenerative ECLS systems (ECLSS) for all habitation concepts, their operation comes with initial mass penalties and maintenance overheads when compared to simpler open-loop architectures. Because of this, NASA is currently pro-posing an open-loop, consumables-based architecture for its surface habitats to achieve initial launch and delivery lander mass targets while scarring for the in-corporation of regenerative ECLSS to meet longer mission durations and sustained presence. With such an architecture, oxygen and potable water are needed consumables, which initial ISRU systems may be able to provide in a pilot capacity. Although the TH is expecting to utilize regenerative ECLSS, advancements in lunar surface-based ISRU and possible re-supply of spacecraft in lunar or Mars orbit could significantly reduce the logistical need for ECLSS related spares on TH and possibly allow a similar open-loop and consumables-based architecture. Table 1 Notional ECLSS consumables per mission use for SH and TH [5]. SH (28-day) Open Loop: Water (kg) 288 | Oxygen (kg) 30 TH (1110-day) Closed-Loop: Water (kg) 182 | Oxygen (kg) 123 In addition to ECLSS mass concerns, the SH is facing challenges with energy storage to support operations over periods of darkness exceeding 100 hours. Both battery and fuel cell-based power architectures are being traded, opening options for external power generation and energy storage. One possibility is ISRU-produced H2 and O2 feeding external primary fuel cell systems which could supplement habitation power generation while reducing initial mass and volume until much more powerful fission power systems might be deployed. Conclusion: Significant advancements are being made in evolvable habitation concepts that span from near-term technologies, such as inflatable structures under NextSTEP, to potentially revolutionary capabilities like the lunar surface construction as funded through the Moon-to-Mars Planetary Autonomous Construction Technologies (MMPACT) project [7]. As NASA investigates both heritage capabilities and rap-idly advancing, disruptive technologies, there are likely many near-term opportunities for initial ISRU capabilities to significantly aid human habitation and increase self-sufficiency beyond Earth.

habitation↗

Post-Flight Quantification of LOFTID Aeroshell Deflection Using Feature Tracking

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was a flight demonstration of the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology, which has the potential to enable delivery of heavy payloads to Mars, Venus, and Titan, as well as return to Earth. Unlike rigid aeroshells that are constrained by the diameter of the launch vehicle shroud, inflatable aeroshells can be deployed to a much larger drag area, thus allowing a more massive spacecraft to begin its deceleration at higher altitudes and experience less heating. On November 10, 2022, the LOFTID reentry vehicle launched aboard a United Launch Alliance Atlas V rocket to low-Earth orbit. The aeroshell was inflated to its full 6-meter diameter, and the vehicle then successfully re-entered the atmosphere, landing in the Pacific Ocean. The aeroshell was composed of seven tori bound together by high strength straps to create a 70-degree half-angle sphere-cone, and the forebody was covered with a flexible thermal protection system (FTPS) (Fig. 1). The centerbody of the vehicle housed six visual cameras. Each camera was made up of 1920 x 1080 pixels and had a field-of-view (FOV) of 85.4° x 55.6°, resulting in a resolution of less than 0.1" at all locations on the aftbody side of the aeroshell. The approximate locations of the cameras and their associated FOVs is shown in Fig. 2. The high loads experienced during flight resulted in the cone of the aeroshell deflecting. This behavior was seen during the static load testing of the aeroshell in May 2021, in which loads ranging from 1,000 to 20,000 lbf were applied, and deflections of up to ~1.7° were observed. The LOFTID team was interested in estimating the deflection of the aeroshell during the its entry into Earth's atmosphere. Before launch, 1"-diameter black circles were drawn on select structural straps for tracking with the visual cameras; the change in position of these features could then be used to calculate aeroshell deflection angle.

Hannah S. Alpert↗

NASA's Habitation Development Status: Current Concepts and ISRU Opportunities

Introduction: The National Aeronautics and Space Administration (NASA) is embarking on a bold journey to return humankind to the Moon and onward to Mars with innovative commercial, international, and academic partnerships. Under the Artemis series of missions, NASA seeks to establish sustained human exploration of deep space through an objectives-based approach. This approach drives the identification of needed system functionality and the current and future capabilities which will eventually allow humanity to sustainably live beyond Earth. Providing evolvable and scalable habitation is a cornerstone function that calls for the collection and integration of current, developmental, and future technologies that can meet near-term exploration needs while growing into long-term sustained presence. NASA is advancing in-space habitation through its Next Space Technologies for Exploration Partnerships (NextSTEP) model while designing lunar, Mars transit, and Mars surface habitat government reference concepts for Artemis missions. These efforts have unveiled possible near-term opportunities for the in-space resource utilization community if human habitation is considered a future customer of space resources. NextSTEP Habitation Development: NASA is closely working with commercial partners under its NextSTEP Appendix A model to advance habitation systems in the arena of inflatable and composite habitation structures. Such efforts promise efficiencies in volumetric packaging and overall spacecraft mass respectively. Recent testing by commercial partners have helped to quantify possible failure mechanisms for inflatable structures while advancing their technology towards eventual flight certification. The advancement of such Class II habitation structures, in which the habitat is only fully deployed once in-space or on a planetary surface, is critical to providing increased habitable volume for long-duration missions with no additional mass penalties. The progression of such technology is infused into NASA’s government reference concepts for notional deep space habitation concepts. Current Government Reference Concepts: To best inform the formulation of future collaborative solicitations, NASA employs the practice of internally developing reference concepts for future exploration elements. These concepts aid in identifying the functions and capabilities needed to complete NASA missions as well as feasible solutions within the timeframe needed. Government reference concepts for a lunar Surface Habitat, Mars Transit Habitat, and Mars Sur-face Habitat are continuously being developed and updated to better guide the Agency’s overall exploration architecture. Lunar Surface Habitat. As NASA returns to the Moon, it is evaluating possible lunar surface habitation concepts. The Surface Habitat (SH) reference concept entails a hybrid metallic-inflatable structure capable of initially housing two crew for surface stays of up to 30 days in duration. While initial missions may span ~7 days in duration, consideration is being given to expanding SH’s capability to support a crew of four for up to 60 days over its 15-year design life. Functionally, the SH serves as a ‘hub’ for all Artemis crewed surface operations, providing internal volume for maintenance, medical, logistics, science utilization, and extravehicular activity (EVA) support in addition to core habitation functionality such as environmental control and life support (ECLS) and power generation and distribution among many others. Additionally, NASA has entered a study agreement with the Italian Space Agency (Agenzia Spaziale Italiana – ASI) to investigation a possible Multi-Purpose Habitat (MPH) as an additional or augmenting habit-able element for the lunar surface. Mars Transit Habitat. NASA’s current architectural concept for initial human missions to Mars entails the utilization of a transit habitat (TH) to transport a four-person crew to and from Mars orbit, departing from and returning to a lunar near-rectilinear halo orbit (NRHO), over the course of a ~1,200-day mission. While holding a similar 15-year design lifetime, TH will also support a series of analog mission activities in NRHO to gradually test the systems and interaction with lunar surface elements, some of which may be adapted for Mars surface exploration. Holding similar functional capabilities as SH, TH is sized to support much longer durations in space and greater logistical independence. Mars Surface Habitat. NASA is still exploring the concept of operations for initial crewed missions to Mars. As such, the Mars Surface Habitat (MSH) concept is still in its infancy as options for mobile, pressurized habitation and stationary habitats are being explored. It is expected MSH will leverage heavily from the lunar SH and possible lunar pressurized rover, however the very different Martian environment will likely necessitate modifications. ISRU Opportunities: Despite the advancements under NASA’s NextSTEP habitation work and continually optimized reference concepts, NASA is facing near-term mass and power challenges that may create opportunities to the ISRU community by providing yet another possible customer for space resources. While NASA desires to use regenerative ECLS systems (ECLSS) for all habitation concepts, their operation comes with initial mass penalties and maintenance overheads when compared to simpler open-loop architectures. Because of this, NASA is currently pro-posing an open-loop, consumables-based architecture for its surface habitats to achieve initial launch and delivery lander mass targets while scarring for the in-corporation of regenerative ECLSS to meet longer mission durations and sustained presence. With such an architecture, oxygen and potable water are needed consumables, which initial ISRU systems may be able to provide in a pilot capacity. Although the TH is expecting to utilize regenerative ECLSS, advancements in lunar surface-based ISRU and possible re-supply of spacecraft in lunar or Mars orbit could significantly reduce the logistical need for ECLSS related spares on TH and possibly allow a similar open-loop and consumables-based architecture. In addition to ECLSS mass concerns, the SH is facing challenges with energy storage to support operations over periods of darkness exceeding 100 hours. Both battery and fuel cell-based power architectures are being traded, opening options for external power generation and energy storage. One possibility is ISRU-produced H2 and O2 feeding external primary fuel cell systems which could supplement habitation power generation while reducing initial mass and volume until much more powerful fission power systems might be deployed. Conclusion: Significant advancements are being made in evolvable habitation concepts that span from near-term technologies, such as inflatable structures under NextSTEP, to potentially revolutionary capabilities like the lunar surface construction as funded through the Moon-to-Mars Planetary Autonomous Construction Technologies (MMPACT) project. As NASA investigates both heritage capabilities and rap-idly advancing, disruptive technologies, there are likely many near-term opportunities for initial ISRU capabilities to significantly aid human habitation and increase self-sufficiency beyond Earth.

habitation↗

Post-Flight Quantification of LOFTID Aeroshell Deflection Using Feature Tracking

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was a flight demonstration of the Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology, which has the potential to enable delivery of heavy payloads to Mars, Venus, and Titan, as well as return to Earth. Unlike rigid aeroshells that are constrained by the diameter of the launch vehicle shroud, inflatable aeroshells can be deployed to a much larger drag area, thus allowing a more massive spacecraft to begin its deceleration at higher altitudes and experience less heating. On November 10, 2022, the LOFTID reentry vehicle launched aboard a United Launch Alliance Atlas V rocket to low-Earth orbit. The aeroshell was inflated to its full 6-meter diameter, and the vehicle then successfully re-entered the atmosphere, landing in the Pacific Ocean. The aeroshell was composed of seven tori bound together by high strength straps to create a 70-degree half-angle sphere-cone, and the forebody was covered with a flexible thermal protection system (FTPS) (Fig. 1). The centerbody of the vehicle housed six visual cameras. Each camera was made up of 1920 x 1080 pixels and had a field-of-view (FOV) of 85.4° x 55.6°, resulting in a resolution of less than 0.1" at all locations on the aftbody side of the aeroshell. The approximate locations of the cameras and their associated FOVs is shown in Fig. 2. The high loads experienced during flight resulted in the cone of the aeroshell deflecting. This behavior was seen during the static load testing of the aeroshell in May 2021, in which loads ranging from 1,000 to 20,000 lbf were applied, and deflections of up to ~1.7° were observed. The LOFTID team was interested in estimating the deflection of the aeroshell during the its entry into Earth's atmosphere. Before launch, 1"-diameter black circles were drawn on select structural straps for tracking with the visual cameras; the change in position of these features could then be used to calculate aeroshell deflection angle.

Hannah S. Alpert↗

Evaluation of the LOFTID Flight Thermocouple Measurements

The Flexible Thermal Protection System (FTPS) on NASA’s Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) vehicle was instrumented with thermocouples (TC) to measure the in-depth thermal response during entry into Earth’s atmosphere. Accurate flight temperature measurements are critical for verifying vehicle performance during the flight test and reducing uncertainties in the thermal models. The deployable nature of inflatable decelerator technology presents challenges, namely the TCs need to be compactable, cannot damage the FTPS nor the inflatable structure, and need to be able to withstand high temperatures and large thermal gradients over significant running lengths. As previously reported, an extensive ground-test campaign was conducted prior to flight to inform the selection of the LOFTID FTPS TCs which minimized all known potential error sources. Overall, the resulting flight FTPS TC measurements were exceptionally clean throughout the atmospheric entry heat pulse. However, a few of the FTPS TCs still exhibited electrical shorting or other anomalous behavior. This paper presents the flight measurements made by the LOFTID FTPS TCs, identifies anomalous behavior, and discusses potential explanations for the causes of the anomalous behavior. Lastly, recommendations to further mitigate TC measurement error on future Hypersonic Inflatable Aerodynamic Decelerator (HIAD) missions are provided.

Ruth A Miller↗