Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microphonics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Acoustic pressures on a prop-fan aircraft fuselage surface

Acoustic pressure amplitude and phase distributions on the surface of a simulated fuselage (a rigid semi-cylinder) installed in an acoustically treated wind tunnel near a Prop-Fan model were measured. The test conditions simulated the relative tip Mach number and blade loading of a full scale Prop-Fan at high altitude 0.8 Mach number cruise. Measurements were also made at equivalent microphone locations without the semi-cylinder to establish the effects of the presence of a fuselage on the sound pressure amplitudes. These effects were found to be 6 dB at 90 degrees incidence, decreasing to no effect at grazing incidence. Comparison of measurements and calculations using a Hamilton Standard Prop-Fan noise calculation computer program showed good agreement in peak level and in phase distribution. Continuous recordings were also made of a Prop-Fan RPM sweep at constant simulated flight speed and a simulated flight speed sweep at constant Prop-Fan RPM. These showed smooth variations in noise level over the tip Mach number range 0.878 to 1.143.

Magliozzi, B.↗

Aerodynamic aspects of shock containing jet plumes

Aerodynamic and acoustic measurements of shock-free and shock-containing plumes were acquired for several supersonic free-jet model nozzles. The purpose was to investigate important features of the broadband shock noise generation process. The aerodynamic measurements include the variation of shock cell spacing and strength as a function of nozzle pressure ratio, and longitudinal turbulent-mass-flux axial development as determined by a hot-film probe. In addition, correlations of the hot-film probe with a near-field microphone were obtained. These measurements provide useful information concerning the relation of peak shock noise frequency and level with variations in shock cell spacing and strength. In general, it is shown that a distinction must be made between plumes containing weak and strong imbedded shocks. Strong shocks diminish the level of emitted shock noise and influence the behavior of the jet mixing noise process. The probable location and spectral content for the shock-shear layer interaction mechanism is indicated by the correlations. Numerical inviscid plume comparisons with experimental data are also included.

Seiner, J. M.↗

Flow field and acoustic properties of a Mach number 0.9 jet at a low Reynolds number

An experimental study of the flow field and acoustic properties of a low Reynolds number M = 0.9 jet has been performed in a low pressure anechoic test chamber. The mean flow field was surveyed with a conventional pitot pressure probe and flow fluctuations were detected with a normal hot wire probe. Also, condenser microphone measurements were made in the acoustic field. The flow fluctuations within the jet were found to be dominated initially by a relatively discrete, large-scale, wave-like instability centered around a Strouhal number of 0.44. The axial wavelength of this instability was determined to be 1.45 jet diameters and its azimuthal character includes the n = 0 and n = plus or minus 1 modes. The growth of this instability coupled with its nonlinear breakdown are major contributors to the termination of the potential core region of the jet. The acoustic field of the jet, in contrast to the flow field, has a broad frequency spectrum with a peak amplitude near a Strouhal number of St = 0.2. The results indicate that a nonlinear mechanism involving the large-scale flow instability is responsible for a dominant portion of the noise generated from this jet.

Stromberg, J. L.↗

Flight and tunnel test results of the MDC mechanical jet noise suppressor nozzle

The flight and wind tunnel tests to determine the acoustic and performance effects of a mechanical jet noise suppressor nozzle mounted on a Viper engine of an HS-125 airplane are discussed. Flyover noise measurements were made with microphones mounted on top of a 137.5 m bridge tower. Seven nozzle configurations including two references nozzles, two suppressors, and three ejector inlets were tested. The suppressor nozzle of interest for an advanced supersonic transport, the suppressor/treated ejector, achieved a measured noise reduction of 14 EPNdB relative to a conventional conical reference nozzle at the highest pressure ratio tested (approximately 2.5). The unique engine nacelle, flight hardware, and nacelles from the HS-125 flight test program, combined with a simulated HS-125 fuselage were windtunnel tested. Both propulsion and acoustic data were recorded. Preliminary thrust data results from the wind tunnel tests are summarized and compared to other mechanical suppressor test results. The test results indicate that a noise reduction of at least 16 EPNdB would be possible for the suppressor/ejector nozzle scaled to typical AST engine size with a 5% thrust loss at a typical takeoff climb speed.

Fitzsimmons, R. D.↗

Prediction of blade-vortex interaction noise from measured blade pressure

The impulsive nature of noise due to the interaction of a rotor blade with a tip vortex is studied. The time signature of this noise is calculated theoretically based on the measured blade surface pressure fluctuation of an operational load survey rotor in slow descending flight and is compared with the simultaneous microphone measurement. Particularly, the physical understanding of the characteristic features of a waveform is extensively studied in order to understand the generating mechanism and to identify the important parameters. The interaction trajectory of a tip vortex on an acoustic planform is shown to be a very important parameter for the impulsive shape of the noise. The unsteady nature of the pressure distribution at the very leading edge is also important to the pulse shape. The theoretical model using noncompact liner acoustics predicts the general shape of interaction impulse pretty well except for peak amplitude which requires more continuous information along the span at the leading edge.

Nakamura, Y.↗

Flight test of a pure-tone acoustic source

Static and flight testing of a pure-tone acoustic source were conducted in order to: (1) determine if a 4-KHz tone radiated by a source in flight and mixed with broadband aircraft flyover noise could be measured on the ground with a high degree of statistical confidence; (2) determine how well a comparison could be made of flight-to-static tone radiation pattern and a static radiation pattern; and (3) determine if there were any installation effects on the radiation pattern due to the flight vehicle. Narrow-band acoustic data were measured and averaged over eight microphones to obtain a high statistical confidence. The flight data were adjusted to an equivalent static condition by applying corrections for retarded time, spherical spreading, atmospheric absorption, ground impedance, instrumentation constraints, convective amplification, and the Doppler shift. The flight-to-static results are in excellent agreement with the measured static data. No installation effects were observed on the radiation pattern.

Mueller, A. W.↗

Effect of facility variation on the acoustic characteristics of three single stream nozzles

The characteristics of the jet noise produced by three single stream nozzles have been investigated statically at the NASA-Lewis Research Center outdoor jet acoustic facility. The nozzles consisted of a 7.6 cm diameter convergent conical, a 10.2 cm diameter convergent conical and an 8-lobe daisy nozzle with 7.6 cm equivalent diameter flow area. The acoustic experiments at NASA covered pressure ratios from 1.4 to 2.5 at total temperatures of 811 K and ambient. The data obtained with four different microphone arrays are compared.

Gutierrez, O. A.↗

A high frequency silicon pressure sensor

Theoretical and design considerations as well as fabrication and experimental work involved in the development of high-frequency silicon pressure sensors with an ultra-small diaphragm are discussed. A sensor is presented with a rectangular diaphragm of 0.0127 cm x 0.0254 cm x 1.06 micron; the sensor has a natural frequency of 625 kHz and a sensitivity of 0.82 mv/v-psi. High-frequency results from shock tube testing and low-frequency (less than 50 kHz) comparison with microphones are given.

Kahng, S. K.↗

A modal separation measurement technique for broadband noise propagating inside circular ducts

A measurement technique which separates broadband noise propagating inside circular ducts into the acoustic duct modes is developed. The technique is also applicable to discrete frequency noise. The acoustic modes are produced by weighted combinations of the instantaneous outputs of microphones spaced around the duct circumference. The technique is compared with the cross spectral density approach presently available and found to have certain advantages, and disadvantages. Considerable simplification of both the new technique and the cross spectral density approach occurs when no correlation exists between different circumferential mode orders. The properties leading to uncorrelated modes and experimental tests which verify this condition are discussed. The modal measurement technique is applied to the case of broadband noise generated by flow through a coaxial obstruction (nozzle or orifice) in a pipe. Different circumferential mode orders are shown to be uncorrelated for this type of noise source.

Kerschen, E. J.↗

Theoretical and experimental evaluation of transmission loss of cylinders

A technique is reported which evaluates the transmission loss of a cylinder from measurements of the incident and transmitted intensities. Incident intensity is calculated from the space-averaged measured pressure and the assumption that the source space is reverberant. Transmitted intensity is measured by means of the microphone acoustic intensity technique using a fast Fourier transform analyzer. The first dip at the ring frequency, and the other at the critical coincidence frequency are predicted in the transmission loss curve of a cylindrical shell with a 0.762 m diameter and a 1.67 m length. Results are compared and demonstrate good agreement for frequencies above 500 Hz. It is concluded that the technique combining the measurement of both intensities gives accurate results and is simpler and less expensive than the conventional method.

Wang, Y. S.↗

Experiments on the nonlinear characteristics of noise propagation from low and moderate Reynolds number supersonic jets

A series of experiments were conducted on high-speed model jets to identify and quantify the distortion of radiated noise by nonlinear propagation effects. The jets were operated in a low to moderate Reynolds number range, and the radiated noise was either broadband or discrete in frequency. Three condenser microphones were used to measure the waveforms propagated by the axisymmetric, cold model jets of Mach numbers 2.1 and 2.5. Relatively low Reynolds numbers were obtained by exhausting the jets into a low pressure anechoic test chamber. Nonlinear propagation distortion effects, such as wave steepening, harmonic generation and wave merging, were easily quantified. At a moderate Reynolds number, low frequency production and wave amalgamation, measured by a decrease in the zero crossings per unit time, were quantified in the propagation of sound away from the jet.

Gallagher, J. A.↗

Ground effects on aircraft noise for a wide-body commercial airplane

Ground effects on noise from a high-bypass ratio engined aircraft are investigated. A 747 is flown at altitudes from 30 to 960 m past a 20-microphone array, and ground effects are calculated from noise measurements as a function of elevation angle and slant range. Results are given in terms of EPNL units and are compared with previous results of a turbojet-powered T-38 and SAE-recommended empirical lateral attenuation prediction procedures. Theoretical predictions are made based on a method developed by Pao et al. (1978) and are compared with both 747 and T-38 results, demonstrating good agreement although a consistent underprediction of peak measured attenuation is observed. Measured ground effects are found largest at 200 Hz, and no definite shielding differences are apparent for a directivity angle of 122.5 deg. Less lateral attenuation of effective perceived noise is measured for both aircraft and is attributed to the dominance of low-frequency noise in the source spectrum.

Willshire, W. L., Jr.↗

Mixer nozzle aeroacoustic characteristics for the energy efficient engine

Aeroacoustic tests are conducted on scale model mixer nozzle configurations, a separate flow nozzle, and a baseline conical nozzle in an anechoic chamber free-jet facility to investigate exhaust system designs. Far-field acoustic data and exhaust jet plume aerodynamic data are obtained for various combinations of exhaust jet velocity and simulated flight speed, with corrected microphone data at a constant 12.2 m arc distance, and scaled acoustic data at a sideline distance of 457 m. It is found that jet plume aerodynamic and acoustic characteristics of lobed mixer exhaust systems are similar to those of a conical nozzle operating at the same specific thrust, although differences occur at high frequencies, where the sound pressure level of the mixer nozzle is 1-5 dB higher than that of a conical nozzle. In addition, no direct correlation is found between exit plane turbulence levels and plume development or acoustic characteristics for mixer exhaust configurations.

Gliebe, P. R.↗

Flow and acoustic properties of low Reynolds number supersonic underexpanded jets

Flow and acoustic measurements are made of cold model jets exhausting from a choked nozzle at pressure conditions corresponding to those of Mach 1.4 and 2.1 jets to investigate noise production properties of underexpanded supersonic jets. Mean flow measurements are made using pitot and static pressure probes, with flow fluctuation measurements made with a hot-wire probe and acoustic measurements made with a transversing microphone. Two convergent nozzles with exit diameters of 7.0 and 7.9 mm are used with an exciter consisting of a 0.8 mm tungsten electrode positioned 2 mm from the exit. Shock structure is observed as having a significant effect on the development of the flow field, while large-scale instabilities have higher growth rates in the shock containing underexpanded jets. The role of the asymmetric n = + or - 1 sinusoidal instability is clarified, and results suggest that the broadband shock associated noise of conventional high Reynolds number jets is not related to large-scale jet instability.

Hu, T. F.↗

Detection of infrasound generated by Clear Air Turbulence (CAT)

A unified data acquisiton system which is an AM carrier system consisting of a converter signal, conditioning electronics, and peripheral equipment was checked and calibrated and installed in a mobile van. A microphone array in the shape of a 244-m equilateral triangle was connected to the data acquisition system using 457-m long cables. Development of techniques for signal processing for interpreting the infrasonic signature (differentiating between CAT and other sources of infrasound) is summarized. Once patches of CAT are located in the atmosphere, corroboration can be achieved through test flights of aircraft into the suspected region.

Meredith, R.↗

Acoustic ground impedance meter

A compact, portable instrument was developed to measure the acoustic impedance of the ground, or other surfaces, by direct pressure-volume velocity measurement. A Helmholz resonator, constructed of heavy-walled stainless steel but open at the bottom, is positioned over the surface having the unknown impedance. The sound source, a cam-driven piston of known stroke and thus known volume velocity, is located in the neck of the resonator. The cam speed is a variable up to a maximum 3600 rpm. The sound pressure at the test surface is measured by means of a microphone flush-mounted in the wall of the chamber. An optical monitor of the piston displacement permits measurement of the phase angle between the volume velocity and the sound pressure, from which the real and imaginary parts of the impedance can be evaluated. Measurements using a 5-lobed cam can be made up to 300 Hz. Detailed design criteria and results on a soil sample are presented.

Zuckerwar, A. J.↗

Prediction of blade vortex interaction noise from measured blade pressure

The impulsive nature of noise due to the interaction of a rotor blade with a tip vortex is studied. The time signature of this noise is calculated theoretically based on the measured blade surface pressure fluctuation of an operational load survey rotor in slow descending flight and is compared with the simultaneous microphone measurement. Particularly, the physical understanding of the characteristic features of a waveform is extensively studied in order to understand the generating mechanism and to identify the important parameters. The interaction trajectory of a tip vortex on an acoustic planform is shown to be a very important parameter for the impulsive shape of the noise. The unsteady nature of the pressure distribution at the very leading edge is also important to the pulse shape. The theoretical model using noncompact linear acoustics predicts the general shape of interaction impulse pretty well except for peak amplitude which requires more continuous pressure information along the span at the leading edge.

Nakamura, Y.↗

Effect of facility variation on the acoustic characteristics of three single stream nozzles

The characteristics of the jet noise produced by three single stream nozzles were investigated statistically at the NASA-Lewis Research Center outdoor jet acoustic facility. The nozzles consisted of a 7.6 cm diameter convergent conical, a 10.2 cm diameter convergent conical and an 8-lobe daisy nozzle with 7.6 cm equivalent diameter flow area. The same nozzles were tested previously at cold flow conditions in other facilities such as the Royal Aircraft Establishment (RAE) 7.3 m acoustic wind tunnel. The acoustic experiments at NASA covered pressure ratios from 1.4 to 2.5 at total temperatures of 811 K and ambient. The data obtained with four different microphone arrays are compared. The results are also compared with data taken at the RAE facility and with a NASA prediction procedure.

Gutierrez, O. A.↗