Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Irradiation-induced damage evolution in concentrated Ni-based alloys

Understanding the effects of chemical complexity from the number, type and concentration of alloying elements in single-phase concentred solid-solution alloys (SP-CSAs) on defect dynamics and microstructure evolution is pivotal for developing next-generation radiation-tolerant structural alloys. A specially chosen set of SP-CSAs with different chemical complexity (Ni 80 Fe 20 , Ni 80 Cr 20 and Ni 40 Fe 40 Cr 20 ) are investigated using 1.5 MeV Mn ions over a wide fluence range, from 2 × 10 13 to 1 × 10 16 ions cm –2 at room temperature. Based on an integrated study of Rutherford backscattering spectroscopy in channeling geometry and molecular dynamics simulations, the results demonstrate that Ni 40 Fe 40 Cr 20 is more radiation tolerant than Ni 80 Fe 20 , Ni 80 Cr 20 and elemental Ni in the low fluence regime. While chemical complexity of this set of SP-CSAs is clearly demonstrated to affect defect evolution through suppressed defect production and enhanced recombination at early stages, the effect of the mixed ferro- and anti-ferromagnetic interactions is not the only controlling factor responsible for the improved radiation performance. As a result, the observed strong alloying effect on defect evolution is attributed to the altered defect migration mobilities of defect clusters in these alloys, an intrinsic characteristic of the complex energy landscapes in CSAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Radio-Frequency Rapid Thermal Processing Enabling Spatial Phase Transformation and Nanocrystallization of Soft Magnetic Amorphous Alloys

Thermal processing of soft magnetic amorphous and nanocrystalline alloys is explored under the influence of radio-frequency induction-heating techniques. Direct induction-heating concepts based on longitudinal and transverse flux heating are examined and the details of electromagnetic fields interaction with metallic strips are discussed by analytical calculations as well as finite element analysis. Initial experimental results confirming spatial control of phase transformations and nanocrystallization within a single strip of Finemet Fe-based amorphous ribbons are reported. Here, the degree to which primary and secondary crystallization temperature are achieved depends on the spacing between the ribbon relative to the induction coil as well as the coil design and configuration. For transverse coil configurations, the local temperature and therefore microstructural evolution is different across the lateral dimension of processed ribbons, with reduced gap sizes producing enhanced peak temperatures and larger temperature distributions with greater spatial variation in microstructure. In addition, indirect susceptor-based induction heating under tension is performed and the impact of microstructure is demonstrated. Herein, potential for exploiting spatially optimized phase transformations is illustrated through electromagnetic field–assisted processing in a scalable manufacturing process with amorphous and nanocrystalline soft magnetic alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural heterogeneities in additively manufactured refractory alloy C103 and their implications for room and elevated temperature mechanical behavior

Considering the vast component design space enabled by fusion-based additive manufacturing (F-BAM) processes, e.g., directed energy deposition (DED), the scale-up manufacturing of Nb-alloys with F-BAM is advantageous for structural applications. However, varying thermokinetic parameters-induced microstructural heterogeneities are prevalent within the F-BAM processed alloys. Such microstructural heterogeneities can have significant implications for the room and elevated temperature mechanical behavior. While a few studies investigating F-BAM processed alloy C103 are available, none of these studies investigate the microstructural heterogeneities – including those associated with solidification growth modes and second phase particles – and the effect thereof on the mechanical behavior. To this end, we investigate the microstructurally heterogeneous regions with varying solidification growth morphologies, segregation behavior, and second phase particle attributes within the laser-DED processed alloy C103. The implications of such heterogeneous regions for room- and elevated-temperature tensile behavior and damage mechanisms are revealed. Particularly, the interface between the cellular and planar region is identified as susceptible to deformation localization. The implications of hot isostatic pressing (HIP) for the consolidation behavior, microstructural evolution, and resulting mechanical behavior are also discussed. Although the recrystallization and grain growth led to a reduced yield strength in the HIPed condition, the homogenization of microstructure alleviated the deformation localization sites, such as the planar/cellular interface within the melt pool. The homogenized microstructure alongside the enhanced consolidation upon HIP led to an enhanced elongation to failure. Findings establish microstructural design considerations in F-BAM processed Nb alloys and also facilitate design of post-processing heat treatments for achieving improved mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Investigation of the Use of Laser Shock Peening for Enhancing Fatigue and Stress Corrosion Cracking Resistance of Nuclear Energy Materials

The objective of this project, which includes close collaboration with scientists from INL and ANL, is to investigate and demonstrate the use of advanced mechanical surface treatments like laser shock peening (LSP) and ultrasonic nanocrystal surface modification (UNSM) and establish baseline parameters for enhancing the fatigue properties and SCC resistance of nuclear materials like nickel-based alloy 600 and 304 stainless steel. The research program includes the following key elements/tasks: 1) Procurement of Alloy 600 and 304 SS, heat treatment studies; 2) LSP and UNSM processing of base metal and welds/HAZ of alloys 600 and 304; (3) measurement and mapping of surface and sub-surface residual strains/stresses and microstructural changes as a function of process parameters using novel methods; (4) determination of thermal relaxation of residual stresses (macro and micro) and microstructure evolution with time at high temperatures typical of service conditions and modeling of the kinetics of relaxation; (5) evaluation of the effects of residual stress, near surface microstructure and temperature on SCC and fatigue resistance and associated microstructural mechanisms; and (6) studies of the effects of bulk and surface grain boundary engineering on improvements in the SCC resistance and associated microstructural and cracking mechanisms

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Preliminary Results on Process Modeling Tools for Determining Variability in Additively Manufactured Stainless Steel 316 Parts

The Advanced Materials and Manufacturing Technologies program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. However, the distinct characteristics of additive manufacturing (AM) materials, stemming from their unique processing history, microstructure, and properties, pose significant challenges for the qualification and certification of nuclear components. These challenges primarily arise from component-scale variations in microstructure and properties influenced by local process conditions and geometry, which affect thermal history, melt pool dynamics, and microstructure evolution. Computational modeling tools can play a crucial role in predicting and controlling this variability. This report presents preliminary results on process modeling tools designed to predict microstructure variability in additively manufactured stainless steel 316 parts. It details the software packages and physical modeling approaches employed to simulate an AM component within an automated process modeling workflow. Initial results are demonstrated through comparisons between predicted microstructures and experimental measurements across various representative processing conditions. The report concludes by discussing the challenges inherent in process modeling of AM components and outlines a plan for future development needs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Process-Microstructure-Property Relationships in Low Heat Input Wire-Arc Additive Manufacturing (WAAM) of Ni-Based Superalloy Haynes 282

Conference presentation on WAAM process optimization on Ni-based superalloy Haynes® 282®. This alloy is targeted for advanced power generation systems for its superior high temperature mechanical properties. Wire-arc additive manufacturing (WAAM) offers attractive cost and materials savings with high deposition rates. Based on initial build process optimization, WAAM blocks were made, and screened for defects using high-throughput CT scanning. The microstructural evolution in arc energy range of 250-700 J/mm was characterized in the as-built and aged conditions, using electron microscopy. Results showed self-consistent microstructure across conditions, with grain size dependence on arc energy, MC and M6C carbides in as-built, and blocky grain boundary M23C6 in as-heat-treated condition. Further reductions in as-built porosity were explored through 20+ combinations of H2 and CO2 additions to shielding gas. Initial results show improved wetting behavior, and bead overlap with up to 1% H2 and up to 0.25% CO2. Combination of experimentally determined datasets provided comprehensive understanding of process-structure-property relationships in WAAM Haynes 282.

Haynes 282↗
DOE OSTI2016

Development of Multiscale Materials Modeling Techniques and Coarse- Graining Strategies for Predicting Materials Degradation in Extreme Irradiation Environments

Exposure of metallic structural materials to irradiation environments results in significant microstructural evolution, property changes and performance degradation, which limits the extended operation of current generation light water reactors and restricts the design of advanced fission and fusion reactors [1-8]. This effect of irradiation on materials microstructure and properties is a classic example of an inherently multiscale phenomenon, as schematically illustrated in Figure 1a. Pertinent processes range from the atomic nucleus to structural component length scales, spanning more than 15 orders of magnitude. Time scales bridge more than 22 orders of magnitude, with the shortest being less than a femtosecond [1,8]. Further, the mix of radiation-induced features formed and the corresponding property degradation depend on a wide range of material and irradiation variables. This emphasizes the importance of closely integrating models with high-resolution experimental characterization of the evolving radiation- damaged microstructure, including measurements performed in-situ during irradiation. In this article, we review some recent successes through the use of closely coordinated modeling and experimental studies of the defect cluster evolution in irradiated body-centered cubic materials, followed by a discussion of outstanding challenges still to be addressed, which are necessary for the development of comprehensive models of radiation effects in structural materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2018

Effect of Tempering Temperature on the Microstructure and Properties of Fe-2Cr-Mo-0.12C Pressure Vessel Steel

To obtain the high-temperature strength and toughness of the medium–high-temperature–pressure steel, the microstructure evolution and mechanical properties of Fe-2Cr-Mo-0.12C steel subjected to three different tempering temperatures after being normalized were investigated. The results show that the microstructure of the sample, tempered in the range 675-725 °C for 50 min, did not change dramatically, yet the martensite/austenite constituents decomposed, and the bainite lath merged together and transformed into polygonal ferrite. At the same time, the precipitate size increased with an increase in tempering temperature. With the increase in the tempering temperature from 675 to 725 °C, the impact absorbed energy of the Fe-2Cr-Mo-0.12C steel at −40 °C increased from 257 to 325 J, and the high-temperature yield strength decreased; however, the high-temperature ultimate tensile strength tempered at 700 °C was outstanding (422-571 MPa) at different tested temperatures. The variations of the properties were attributed to the decomposition of M/A constituents and the coarsening of the precipitates. Fe-2Cr-Mo-0.12C steel normalized at 930 °C and tempered at 700 °C was found to have the best combination of ductility and strength.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Advanced Microscopy for Characterization of High Burnup Commercial UO 2 Fuel Before and After LOCA Testing

This report presents the results from the microstructural examination of high burnup UO 2 under pre- and post- loss of coolant accident (LOCA) conditions. The work in this report builds and expands upon work previously conducted on high burnup UO 2 fuel at Oak Ridge National Laboratory (ORNL). This work investigates the microstructural evolution that occurs during steady state irradiation of UO 2 , particularly in high burnup fuel. Several high burnup fuel samples were available from historic fuel shipments to ORNL. Microstructural characterization will aid in understanding why the fuel is susceptible to fuel fragmentation and support future work to investigate the formation mechanisms of certain features that form under irradiation. High burnup UO 2 microstructural data is also needed to improve constitutive models intended to predict high burnup fuel fragmentation (HBFF). This report summarizes the microstructural evaluation of these fuel samples to interpret and analyze high burnup fuel microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Additive Manufacturing of High-Entropy Alloys: A Review

Owing to the reduced defects, low cost, and high efficiency, the additive manufacturing (AM) technique has attracted increasingly attention and has been applied in high-entropy alloys (HEAs) in recent years. It was found that AM-processed HEAs possess an optimized microstructure and improved mechanical properties. However, no report has been proposed to review the application of the AM method in preparing bulk HEAs. Hence, it is necessary to introduce AM-processed HEAs in terms of applications, microstructures, mechanical properties, and challenges to provide readers with fundamental understanding. Specifically, we reviewed (1) the application of AM methods in the fabrication of HEAs and (2) the post-heat treatment effect on the microstructural evolution and mechanical properties. Compared with the casting counterparts, AM-HEAs were found to have a superior yield strength and ductility as a consequence of the fine microstructure formed during the rapid solidification in the fabrication process. The post-treatment, such as high isostatic pressing (HIP), can further enhance their properties by removing the existing fabrication defects and residual stress in the AM-HEAs. Furthermore, the mechanical properties can be tuned by either reducing the pre-heating temperature to hinder the phase partitioning or modifying the composition of the HEA to stabilize the solid-solution phase or ductile intermetallic phase in AM materials. Moreover, the processing parameters, fabrication orientation, and scanning method can be optimized to further improve the mechanical performance of the as-built-HEAs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Microstructure and partitioning behavior characteristics in low carbon steels treated by hot-rolling direct quenching and dynamical partitioning processes

In this work, a new process and composition design are proposed for “quenching and partitioning” or Q&P treatment. Three low carbon steels were treated by hot-rolling direct quenching and dynamical partitioning processes (DQ&P). The effects of proeutectoid ferrite and carbon concentration on microstructure evolution and mechanical properties were investigated. The present work obtained DQ&P prototype steels with good mechanical properties and established a new notion on compositions for Q&P processing. Microstructures were characterized by means of electro probe microanalyzer (EPMA), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) and X-ray diffraction (XRD), especially the morphology and size of retained austenite. Mechanical properties were measured by uniaxial tensile tests. The results indicated that introducing proeutectoid ferrite can increase the volume fraction of retained austenite and thus improve mechanical properties. TEM observation showed that retained austenite included the film-like inter-lath austenite and blocky austenite located in martensite/ferrite interfaces or surrounded by ferrites. It was interesting that when the carbon concentration is as low as ~ 0.078%, the film-like inter-lath untransformed austenite cannot be stabilized to room temperature and almost all of them transformed into twin martensite. The blocky retained austenite strengthened the interfaces and transformed into twin martensite during the tensile deformation process. The PSEs of specimens all exceeded 20 GPa.%. - Highlights: •This study focused on a new process: Q&P process applying dynamical partitioning. •Ferrite can increase the volume fraction of retained austenite. •The film-like austenite and the blocky austenite were observed. •The low carbon steels treated by new process reached PSEs higher than 20 GPa.%.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Initial Microstructure Examination of High Burnup Fuel with Varying Operational Burnups

his report presents an initial examination of the microstructure of high burnup UO 2 under pre- and postloss of coolant accident (LOCA) conditions. This work builds upon work previously conducted on high burnup UO 2 fuel at Oak Ridge National Laboratory. Studying microstructure evolutions that occur in UO 2 during irradiation, particularly in high burnup fuel, will provide a deeper understanding of fuel fragmentation under simulated LOCA conditions. High burnup UO 2 microstructural data is also needed to improve constitutive models intended to predict high burnup fuel fragmentation. The objective of this work is to begin the process of examining high burnup fuel microstructural features before and after LOCA testing to better understand mechanisms driving experimental observations. Several high burnup fuel samples were available from historic fuel shipments to ORNL. These samples were leveraged along with state-of-the-art microscopy capabilities. This report summarizes the current ongoing work using these fuel samples to interpret and analyze high burnup fuel microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Dislocation loop evolution in F/M steel T91 under in-situ ion irradiation: Influence of the presence of initial dislocations

Ferritic/Martensitic (F/M) steel T91 was irradiated in-situ to 4 and 10 dpa at 470 °C using 1 MeV Kr 2+ . Additionally, the microstructure evolution under irradiation was followed and characterized by in-situ Transmission Electron Microscopy (TEM), in terms of dislocation loop Burgers vector, average size and density as a function of dose. Furthermore, the influence of the presence of dislocations in the pre-irradiated matrix was investigated by comparing the radiation induced defect evolution in grains with and without initial dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Postweld Heat Treatment on Microstructure and Properties of Laser-Welded Ti-24Al-15Nb Alloy Joint

The microstructure evolution and mechanical properties of laser-welded joints of Ti-24Al-15Nb alloy under different postweld heat treatment (PWHT) conditions were systematically investigated. The results show that the microstructure is very sensitive to PWHT temperatures. The weld zone consists of B2 and O phases after PWHT. With the PWHT temperatures increasing from 850 to 1000 °C, the amount of O phase decreases gradually, while the grains of O precipitates become coarser. After PWHT, there are some thin acicular O precipitates in heat-affected zone (HAZ), and the decomposition of α{sub 2}-phase caused by niobium diffusion can be observed in the HAZ. The PWHT can significantly increase the microhardness of joints, resulting from O phase precipitation hardening effect. The tensile strength and elongation of joints can be remarkably improved after PWHT, which was closely related to the strengthening effect of O precipitates and slip transmission between O and B2 phases. In addition, the results indicate that the best mechanical properties can be achieved only when the number and size of O phase and B2 phase are the best match.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Real time study of grain enlargement in zirconium under room-temperature compression across the α to ω phase transition

We report a synchrotron Laue diffraction study on the microstructure evolution in zirconium (Zr) as it undergoes a pressure-driven structural phase transformation, using a recently developed real time scanning x-ray microscopy technique. Time resolved characterizations of microstructure under high pressure show that Zr exhibits a grain enlargement across the α-Zr to ω-Zr structural phase transition at room-temperature, with nucleation and growth of ω-Zr crystals observed from initially a nano-powdered α-Zr matrix. The observed grain enlargement is unusual since the enlargement processes typically require substantially high temperature to overcome the activation barriers for forming and moving of grain boundaries. Possible mechanisms for the grain enlargement are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Hierarchical microstructure of Yb-filled skutterudites through ultrasonically atomized spherical powders for enhanced thermoelectric performance

Hierarchical microstructures are widely explored as a strategy to reduce lattice thermal conductivity in thermoelectric materials while preserving favorable electronic transport. Here we demonstrate that ultrasonic atomization of precursor powders provides an intrinsic pathway to generate such architectures in n-type Yb0.3Co4Sb12 skutterudites. Materials were synthesized by both conventional sealed-ampoule and ultrasonic atomization routes, each yielding essentially single-phase skutterudite after densification. However, the atomized spherical powders undergo a distinct reaction-driven microstructural evolution during thermal treatment prior to densification. Electron microscopy reveals that the skutterudite phase within the particles induces swelling, cracking, and fragmentation of the droplets before consolidation. Multimodal structural and microstructural characterizations show that densification of these fragmented powders produces a hierarchical microstructure consisting of submicron grains, micrometer-scale faceted crystallites, and powder-derived domains separated by oxide-decorated boundaries. Comprehensive thermoelectric transport measurements evidence that this multiscale architecture lowers the lattice thermal conductivity while maintaining favorable electronic transport, leading to an average ~10% enhancement in the thermoelectric figure of merit. Complementary 121Sb Mössbauer spectroscopy further indicates lattice softening in the atomized material. These results demonstrate that ultrasonic atomization provides an effective route to engineer hierarchical microstructures in skutterudite thermoelectrics and offers a promising strategy for tailoring thermal transport in energy-conversion materials.

Bouteiller, Hugo [ORNL] (ORCID:0009000421322962)↗
DOE OSTI2021

Microstructural-Level Fuel Performance Modeling of U-Mo Monolithic Fuel

As the physics that governs the microstructural evolution of nuclear fuel span various time and spatial scales, to fully understand the fuel behavior inevitably involves atomic to mesoscale resolution that can be difficult to determine experimentally. Microstructural-level modeling and simulations can be used to develop physics-based materials models that can provide physical understanding to inform fabrication process control, as well as a valuable feedback mechanism between post-irradiation examination (PIE) results and fabrication parameters. In accordance with the program schedule, the primary goals of the microstructure modeling effort are to: 1. Address critical microstructural questions and provide practical guidance to the fabricator via the fuel product specification; 2. Provide mechanistic inputs for the existing fuel performance code to improve its descriptive and predictive capability at the macroscopic scale. In fiscal year (FY)-21, the work scope consisted of six main facets: (1) the effect of carbides on fuel performance; (2) gas diffusivity in different phases; (3) integration of microstructural fuel performance modeling; (4) property degradation; (5) irradiation creep; and (6) historical analysis of microstructure data. Brief summaries of each are included below.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Achieving high-ZT in Te/Se-based thermoelectric materials via volume-constrained shear-induced plastic deformation

This study investigated the correlation between severe plastic deformation and microstructural evolution, along with the corresponding response in the thermoelectric performance. Specifically, severe plastic deformation introduced into intrinsically brittle thermoelectric materials like Bi 2 Te 3 - x Se x leads to microstructural changes ranging from nano- to micro- scales, including phase transformation, phase segregation, and stacking faults. The resultant residual strain and lattice defects in the Bi 2 Te 3-x Se x materials led to engineering of electronic bands, which increases the effective mass of electrons while controlling their concentration, thereby enhancing the power factor.

36 MATERIALS SCIENCE↗