SEARCH · Search NASA

Results for “Parameters optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Photonic Choke-Joints for Dual-Polarization Waveguides

Photonic choke joint (PCJ) structures for dual-polarization waveguides have been investigated for use in device and component packaging. This interface enables the realization of a high performance non-contacting waveguide joint without degrading the in-band signal propagation properties. The choke properties of two tiling approaches, symmetric square Cartesian and octagonal quasi-crystal lattices of metallic posts, are explored and optimal PCJ design parameters are presented. For each of these schemes, the experimental results for structures with finite tilings demonstrate near ideal transmission and reflection performance over a full waveguide band.

Wollack, Edward J.↗

NASA NTRS2012

Analysis of Organic Molecules Extracted from Mars Analogues and Influence of Their Mineralogy Using N-Methyl-N-(tert-butyldimethylsilyl)Trifluoroacetamide Derivatization Coupled with Gas Chromatography Mass Spectrometry in Preparation for the Sample Analysis at Mars Derivatization Experiment on the Mars Science Laboratory Mission

The search for complex organic molecules on Mars, including important biomolecules such as amino acids and carboxylic acids will require a chemical extraction and derivatization step to transform these organic compounds into species that are sufficiently volatile to be detected by gas chromatography mass spectrometry (GCMS). We have developed, a one-pot extraction and chemical derivatization protocol using N-methyl-N-(tert-butyldimethylsilyl)trifluoroacetamide (MTBSTFA) and dimethylformamide (DMF) for the Sample Analysis at Mars (SAM) experiment on the Mars Science Laboratory (MSL). The temperature and duration the derivatization reaction, pre-concentration of chemical derivatives, and gas chromatographic separation parameters have been optimized under SAM instrument design constraints. MTBSTFA/DMF extraction and derivatization at 300 C for several minutes of a variety of terrestrial Mars analogue materials facilitated the detection of amino acids and carboxylic acids in a surface soil sample collected from the Atacama Desert and a carbonate-rich stromatolite sample from Svalbard. However, the rapid reaction of MTBSTFA with water in several analogue materials that contained high abundances of hydrated minerals and the possible deactivation of derivatized compounds by iron oxides, as detected by XRD/XRF using the CheMin field unit Terra, proved to be highly problematic for the direct extraction of organics using MTBSTFA, The combination of pyrolysis and two different chemical derivatization methods employed by SAM should enable a wide range of organic compounds to be detected by GCMS if present on Mars,

Stalport, F.↗

NASA NTRS2013

Trace Contaminant Control: An In-Depth Study of a Silica-Titania Composite for Photocatalytic Remediation of Closed-Environment Habitat Air

This collection of studies focuses on a PCO system for the oxidation of a model compound, ethanol, using an adsorption-enhanced silica-TiO2 composite (STC) as the photocatalyst; studies are aimed at addressing the optimization of various parameters including light source, humidity, temperature, and possible poisoning events for use as part of a system for gaseous trace-contaminant control system in closed-environment habitats. The first goal focused on distinguishing the effect of photon flux (i.e., photons per unit time reaching a surface) from that of photon energy (i.e., wavelength) of a photon source on the PCO of ethanol. Experiments were conducted in a bench-scale annular reactor packed with STC pellets and irradiated with either a UV-A fluorescent black light blue lamp O max=365 nm) at its maximum light intensity or a UV-C germicidal lamp O. max=254 nm) at three levels of light intensity. The STC-catalyzed oxidation of ethanol was found to follow zero-order kinetics with respect to CO2 production, regardless of the photon source. Increased photon flux led to increased EtOH removal, mineralization, and oxidation rate accompanied by lower intermediate concentration in the effluent. The oxidation rate was higher in the reactor irradiated by UV-C than by UV-A (38.4 vs. 31.9 nM s-1 ) at the same photon flux, with similar trends for mineralization (53.9 vs. 43.4%) and reaction quantum efficiency (i.e., photonic efficiency, 63.3 vs. 50.1 nmol C02 ~mol photons-1 ). UV-C irradiation also led to decreased intermediate concentration in the effluent compared to UV -A irradiation. These results demonstrated that STC-catalyzed oxidation is enhanced by both increased photon flux and photon energy. The effect of temperature and relative humidity on the STC-catalyzed degradation of ethanol was also determined using the UV-A light source at its maximum intensity.

Coutts, Janelle L.↗

NASA NTRS2012

The Influence of Mineralogy on Recovering Organic Acids from Mars Analogue Materials Using the One-Pot Derivatization Experiment on the Sample Analysis at Mars(SAM) Instrument Suite

The search for complex organic molecules on Mars, including important biomolecules such as amino acids and carboxylic acids, will require a chemical extraction and a derivatization step to transform these organic compounds into species that are sufficiently volatile to be detected by gas chromatography mass spectrometry (GCMS). We have developed a ''one-pot'' extraction and chemical derivatization protocol using N-methyl-N-(tert-butyldimethylsilyl) trifluoroacetamide (MTBSTFA) and dimethylformamide (DMF) for the Sample Analysis at Mars (SAM) experiment instrument suite on NASA's the Mars Science Laboratory (MSL) mission. The temperature and duration of the derivatization reaction, pre-concentration of chemical derivatives, and gas chromatographic separation parameters have been optimized under SAM instrument design constraints. MTBSTFA/DMF extraction and derivatization at 300 1C for several minutes of a variety of terrestrial Mars analog materials facilitated the detection of amino acids and carboxylic acids in a surface soil sample collected from the Atacama Desert and a carbonate-rich stromatolite sample from Svalbard. However, the rapid reaction of MTBSTFA with water in several analog materials that contained high abundances of hydrated minerals, and the possible deactivation of derivatized compounds by iron oxides, as detected by XRD/XRF using the CheMin field unit Terra, proved to be highly problematic for the direct extraction of organics using MTBSTFA. The combination of pyrolysis and two different wet-chemical derivatization methods employed by SAM should enable a wide range of organic compounds to be detected by GCMS if present on Mars.

MSL↗

NASA NTRS2015

Computational Process Modeling for Additive Manufacturing (OSU)

Powder-Bed Additive Manufacturing (AM) through Direct Metal Laser Sintering (DMLS) or Selective Laser Melting (SLM) is being used by NASA and the Aerospace industry to "print" parts that traditionally are very complex, high cost, or long schedule lead items. The process spreads a thin layer of metal powder over a build platform, then melts the powder in a series of welds in a desired shape. The next layer of powder is applied, and the process is repeated until layer-by-layer, a very complex part can be built. This reduces cost and schedule by eliminating very complex tooling and processes traditionally used in aerospace component manufacturing. To use the process to print end-use items, NASA seeks to understand SLM material well enough to develop a method of qualifying parts for space flight operation. Traditionally, a new material process takes many years and high investment to generate statistical databases and experiential knowledge, but computational modeling can truncate the schedule and cost -many experiments can be run quickly in a model, which would take years and a high material cost to run empirically. This project seeks to optimize material build parameters with reduced time and cost through modeling.

Bagg, Stacey↗

NASA NTRS2015

Multiscale and Multiphysics Modeling of Additive Manufacturing of Advanced Materials

The objective of this proposed project is to research and develop a prediction tool for advanced additive manufacturing (AAM) processes for advanced materials and develop experimental methods to provide fundamental properties and establish validation data. Aircraft structures and engines demand materials that are stronger, useable at much higher temperatures, provide less acoustic transmission, and enable more aeroelastic tailoring than those currently used. Significant improvements in properties can only be achieved by processing the materials under nonequilibrium conditions, such as AAM processes. AAM processes encompass a class of processes that use a focused heat source to create a melt pool on a substrate. Examples include Electron Beam Freeform Fabrication and Direct Metal Deposition. These types of additive processes enable fabrication of parts directly from CAD drawings. To achieve the desired material properties and geometries of the final structure, assessing the impact of process parameters and predicting optimized conditions with numerical modeling as an effective prediction tool is necessary. The targets for the processing are multiple and at different spatial scales, and the physical phenomena associated occur in multiphysics and multiscale. In this project, the research work has been developed to model AAM processes in a multiscale and multiphysics approach. A macroscale model was developed to investigate the residual stresses and distortion in AAM processes. A sequentially coupled, thermomechanical, finite element model was developed and validated experimentally. The results showed the temperature distribution, residual stress, and deformation within the formed deposits and substrates. A mesoscale model was developed to include heat transfer, phase change with mushy zone, incompressible free surface flow, solute redistribution, and surface tension. Because of excessive computing time needed, a parallel computing approach was also tested. In addition, after investigating various methods, a Smoothed Particle Hydrodynamics Model (SPH Model) was developed to model wire feeding process. Its computational efficiency and simple architecture makes it more robust and flexible than other models. More research on material properties may be needed to realistically model the AAM processes. A microscale model was developed to investigate heterogeneous nucleation, dendritic grain growth, epitaxial growth of columnar grains, columnar-to-equiaxed transition, grain transport in melt, and other properties. The orientations of the columnar grains were almost perpendicular to the laser motion's direction. Compared to the similar studies in the literature, the multiple grain morphology modeling result is in the same order of magnitude as optical morphologies in the experiment. Experimental work was conducted to validate different models. An infrared camera was incorporated as a process monitoring and validating tool to identify the solidus and mushy zones during deposition. The images were successfully processed to identify these regions. This research project has investigated multiscale and multiphysics of the complex AAM processes thus leading to advanced understanding of these processes. The project has also developed several modeling tools and experimental validation tools that will be very critical in the future of AAM process qualification and certification.

Liou, Frank↗

NASA NTRS2016

Basin-Scale Assessment of the Land Surface Water Budget in the National Centers for Environmental Prediction Operational and Research NLDAS-2 Systems

The purpose of this study is to evaluate the components of the land surface water budget in the four land surface models (Noah, SAC-Sacramento Soil Moisture Accounting Model, (VIC) Variable Infiltration Capacity Model, and Mosaic) applied in the newly implemented National Centers for Environmental Prediction (NCEP) operational and research versions of the North American Land Data Assimilation System version 2 (NLDAS-2). This work focuses on monthly and annual components of the water budget over 12 National Weather Service (NWS) River Forecast Centers (RFCs). Monthly gridded FLUX Network (FLUXNET) evapotranspiration (ET) from the Max-Planck Institute (MPI) of Germany, U.S. Geological Survey (USGS) total runoff (Q), changes in total water storage (dS/dt, derived as a residual by utilizing MPI ET and USGS Q in the water balance equation), and Gravity Recovery and Climate Experiment (GRACE) observed total water storage anomaly (TWSA) and change (TWSC) are used as reference data sets. Compared to these ET and Q benchmarks, Mosaic and SAC (Noah and VIC) in the operational NLDAS-2 overestimate (underestimate) mean annual reference ET and underestimate (overestimate) mean annual reference Q. The multimodel ensemble mean (MME) is closer to the mean annual reference ET and Q. An anomaly correlation (AC) analysis shows good AC values for simulated monthly mean Q and dS/dt but significantly smaller AC values for simulated ET. Upgraded versions of the models utilized in the research side of NLDAS-2 yield largely improved performance in the simulation of these mean annual and monthly water component diagnostics. These results demonstrate that the three intertwined efforts of improving (1) the scientific understanding of parameterization of land surface processes, (2) the spatial and temporal extent of systematic validation of land surface processes, and (3) the engineering-oriented aspects such as parameter calibration and optimization are key to substantially improving product quality in various land data assimilation systems.

NLDAS-2↗

NASA NTRSDate not supplied

A Multiphysics Study to Improve Specific Energy of Primary Batteries for Low Temperature Operation for Deep Space Missions

Several lander missions on the outer planets such as Europa, Enceladus, and Titan require electrical power to operate scientific and communication equipment. The traditional power generation methods, such as a photovoltaic array, are not feasible as their efficiency drops significantly at these vast distances. The novel radioisotope power systems are not practical today based on current lander designs and the effectiveness of these systems. To perform in situ science on distant planets, a high specific energy battery (>700 Wh/kg) needs to operate for about 480 hours under cold temperatures (-40C or 0C) [1]. While a primary battery such as Li-CFx can provide high specific energy at room temperature, its specific capacity decreases significantly at low temperatures. One of the causes for this drop is low ion and electrical conductivity, and slower reaction kinetics. Slower transport and facile kinetics lead to an increase in the battery’s resistance and higher voltage drops during the cell operation, thus reducing specific capacity. Both the transport and kinetics show a strong dependence on temperature. Thus, a small temperature rise can lead to an increase in the reaction rate and ion conductivity; since the temperature, cell resistance, and specific capacity are interdependent. A conventional battery model accounts for ohmic, thermodynamic, and, electrochemical, and chemical decomposition heating. The ohmic heating can be controlled by designing a resistive microstructure and varying the ratios of the active materials [2]. The kinetics can be improved by increasing the surface area, reducing the particle size, or adding a catalyst. These parameters are often optimized to achieve high specific energy at room temperatures. A similar optimization study is not available at low temperatures and for a primary (high specific energy) battery. For this presentation, we will explore the effect of geometrical, microstructural, and material properties on optimal specific capacity at low temperatures through multiphysics simulations. The ion transport resistance depends on the porosity and the tortuosity of an electrode and the separator.

M. Mehta↗

NASA NTRS2020

Soil Evaporation Stress Determines Soil Moisture‐Evapotranspiration Coupling Strength in Land Surface Modeling

Model‐based estimates of soil moisture (SM)‐evapotranspiration (ET) coupling strength(ρ) vary widely and are prone to bias. Here we apply numerical modeling and remote sensing to identify the process‐level source of modeledρbias with the goal of improving the fidelity of current Earth system models. Results illustrate that modeledρis most strongly determined by soil evaporation (E) stress, and (generally positive)ρmodeling bias is attributable to the oversimplification of soil texture impacts on E stress. Based on new remotely sensed estimates ofρ, we demonstrate that removingρbias via a single optimized E stress parameter leads to improved ET accuracy and resolves a well‐known modeling bias in the partitioning of ET into E and T. As such, we highlight the importance of the stress function relating E and SM and its central role in regulating land‐atmosphere coupling processes impacting local climate.

Jianzhi Dong↗

NASA NTRS2022

Uncertainty Estimation for SMAP Level-1 Brightness Temperature Assimilation at Different Timescales

Soil Moisture Active Passive (SMAP) mission brightness temperature (T(b) ) observations are assimilated into NASA’s Catchment Land Surface Model using an Ensemble Kalman filter to update simulations of surface and root-zone soil moisture. Different time series components of the T(b) observations are assimilated including anomalies, inter-annual variations, and high frequency variations. To optimize the weights that the data assimilation (DA) puts on the observations, the ratio between the uncertainties of modeled and observed T(b) is approximated using modeled and observed soil moisture uncertainties estimated using triple collocation analysis. In a benchmark experiment, T(b) observations are assimilated using a spatially constant 4 Kelvin (K) observation uncertainty, as in the operational SMAP Level-4 algorithm. All DA experiments exhibit notable skill improvements in most regions. Improvements are largest for the inter-annual variations in the simulations of both surface and root-zone soil moisture (mean improvements in terms of Pearson correlation (-) are 0.08 and 0.06, respectively). Anomaly simulations improve similarly (0.07), and improvements in the high-frequency variations are only observed for surface soil moisture simulations (0.06). No notable difference in skill - neither improvement nor deterioration - is observed between the experiments that use optimized observation uncertainty parameters and the 4 K benchmark experiment. This may be explained by the presence of large observation operator errors, which are analytically shown to have the potential to render post-update uncertainty insensitive to inaccuracies in estimates of the Kalman gain. These results have important implications for the design of soil moisture DA systems, in particular for parameterizing model and observation uncertainties.

Hydrology↗

NASA NTRSDate not supplied

Uncertainty Estimation for SMAP Level-1 Brightness Temperature Assimilation at Different Timescales

In this study, we assimilate Soil Moisture Active Passive (SMAP) mission brightness temperature (Tb) observations into NASA’s Catchment Land Surface Model using an Ensemble Kalman filter to update surface and root-zone soil moisture simulations. Different time series components of the Tb observations are assimilated including anomalies, inter-annual variations, and high-frequency variations. To optimize the weights that the data assimilation (DA) puts on the observations, the ratio between the un-certainties of modeled and observed Tb is approximated using modeled and observed soil moisture uncertainties estimated using triple collocation analysis. Results are compared to a benchmark experiment that mimics the operational SMAP Level-4 algorithm, which assimilates Tb observations using a spatially-constant 4 Kelvin (K) observation uncertainty. All DA experiments exhibit notable skill improvements in most regions. Improvements are greatest for the inter-annual variations in the simulations of both surface and root-zone soil moisture (mean improvements in terms of Pearson correlation (-) are 0.08 and 0.06, respectively). Anomaly simulations improve similarly (0.07), and improvements in the high-frequency variations are only observed for sur-face soil moisture simulations (0.06). Strikingly, however, no notable difference in skill—neither improvement nor deterioration—is observed between the experiments that use optimized observation uncertainty parameters and the 4 K benchmark experiment. We show, analytically, that this may be explained by the presence of large observation operator errors, which have the potential to render post-update uncertainty insensitive to inaccuracies in the Kalman gain.

Alexander Gruber↗

NASA NTRSDate not supplied

Advancements in the Camera Setup for Unsteady Pressure Sensitive Paint at NASA Ames Research Center

A test in the Unitary Plan Wind Tunnel at NASA Ames Research Center is scheduled for early 2024 with the intent of showcasing improvements made to unsteady Pressure Sensitive Paint technology. Analysis was performed to investigate how to maximize the system resolving power by optimizing the camera parameters, specifically focal length and focusing distance, while still subject to other system requirements such as field of view and relatively low illumination from the paint. Additionally, the system is upgrading to an 8-camera system from a 4-camera system, so analysis was performed to determine the best way to extend that system to maximize camera coverage and how to most effective reduce the system uncertainty by averaging multiple measurement using camera overlap. These analyses have uncovered new opportunities to improve the unsteady Pressure Sensitive Paint technology without the need for new or expensive hardware and will allow the system to collect better data with simple changes to the design process.

Camera Calibration↗

NASA NTRSDate not supplied

Comparisons of Mixing Efficiency for the Strut Fuel Injector Obtained from Large-Eddy and Reynolds-Averaged Simulations, and Experiments

Mixing efficiency is obtained for a strut fuel injector at hypervelocity flow conditions by using large-eddy simulations (LES), Reynolds-averaged simulations (RAS), and experiments. The injector and flow conditions have been previously investigated by using RAS and experiments as a part of the Enhanced Injection and Mixing Project (EIMP) at the NASA Langley Research Center (LaRC). Because the fidelity of LES is a strong function of the grid, the mixing efficiency is obtained on two grids, the coarser of which is a factor of two coarser in each of the three dimensions with respect to the fine grid. The RAS uses the two-equation linear eddy viscosity and diffusivity modeling of Menter. In RAS, the species diffusivity model exhibits a strong dependence on the turbulent Schmidt number, which is often adjusted until some metric of engineering interest, such as the mixing efficiency, matches the experimental data. In the absence of experimental data, scale-resolving simulations, such as LES, have been proposed as surrogates for experiments that could provide the data needed to “calibrate” the turbulent Schmidt number in the RAS models. This approach is followed because LES requires significantly more computational resources (CPU, data storage, and time) than RAS, making it prohibitive for use in many engineering applications and specifically for parameter exploration or optimization. Here we examine the mixing efficiency obtained from several RAS with different values of the turbulent Schmidt number, and compare the results with those obtained from the LES and experiments. In addition, the least squares fitting approach was used to demonstrate how to obtain an estimate for the turbulent Schmidt number from LES analytically. These estimates were then used together with prior knowledge about RAS model sensitivity to select a turbulence model that was expected to best match the LES data.

LES↗

NASA NTRSDate not supplied

Comparisons of Mixing Efficiency for the Strut Fuel Injector Obtained from Large-Eddy and Reynolds-Averaged Simulations, and Experiments

LES↗

NASA NTRSDate not supplied

Ultrashort Pulsed Laser Treatment: A Novel Sterilization Method for Planetary Protection

Introduction: On missions seeking signs of potential life elsewhere in the solar system, we have an obligation not to bring our own Earthly life with us. Reducing the bioburden (number of living microbes) on spacecraft is therefore required by the COSPAR Policy on Planetary Protection to target bodies that are of interest for understanding the origins of life (such as Mars). The method of spacecraft sterilization predominantly used by NASA is Heat Microbial Reduction, which is typically incompatible with heat-sensitive components such as optics and electronics, and is expensive and time-consuming. Here, we present preliminary results on a novel method for spacecraft hardware sterilization: high-intensity ultrashort (femtosecond) pulsed laser illumination. Femtosecond lasers use extremely high photon fluxes (10^29 photons/sec*cm^2, ~0.03 J/cm^2) in extremely short pulses, which can inactivate even stress-tolerant microbial spores with minimal damage to the spacecraft surface. This rapid sterilization technique could be carried out in situ in a spacecraft assembly clean room using high-speed surface scanning, saving critical time and resources. It also can potentially remove or reduce debris from inactivated cells and spores. Methods: To develop optimal laser processing parameters for inactivating planetary protection-relevant organisms on metal surfaces, we inoculated 1-cm^2 mirror-polished aluminum coupons with Bacillus subtilis spores (2x10^5 spores/coupon) and tested the effect of several parameters, including pulse count and fluence. Sterilization effectiveness was measured by recovering spores using a PVA (polyvinyl acetate) peel and conducting serial dilution and plating for colony-forming units (CFUs). Results: Our results show that pulse count and fluence both affect sterilization effectiveness and that within a certain pulse count range, increasing fluence increases effectiveness. We have demonstrated the ability to reduce viable microbial counts by at least 10^-4. Future work will include testing higher abundances and different species of microorganisms, effectiveness on complex surfaces, compatibility with sensitive surfaces, and quantification of cell debris removal. Femtosecond pulsed laser illumination has the potential to provide dramatic savings in both cost and schedule over current methods of bioburden reduction to prevent forward contamination. It may also have the potential for use in surface sterilization of returned samples to prevent back contamination.

Planetary Protection; Lasers; Sterilization; Bacil↗

NASA NTRSDate not supplied

In-Space Laser Forming Simulated Under Thermal Vacuum (TVAC) Conditions

NASA Marshall Space Flight Center is investigating laser forming under thermal vacuum conditions representative of the space environment through a partnership with the DARPA NOM4D program. The thermal gradient mechanism (TGM) is used to bend a metal sheet towards the laser optics. Laser equipment and process parameters are being optimized for thermal vacuum conditions. Such conditions are representative of the extreme cold and hot temperatures and high vacuum that exist on orbit or on the lunar surface. in situ photogrammetry and thermography assess the bend/counterbend and elucidate the TGM in thermal vacuum. Structured light scanning and metallography after bending reveal the macroscopic and microscopic structure after TGM.

thermal vacuum↗

NASA NTRS1991

Vortex generator design for aircraft inlet distortion as a numerical optimization problem

Aerodynamic compatibility of aircraft/inlet/engine systems is a difficult design problem for aircraft that must operate in many different flight regimes. Takeoff, subsonic cruise, supersonic cruise, transonic maneuvering, and high altitude loiter each place different constraints on inlet design. Vortex generators, small wing like sections mounted on the inside surfaces of the inlet duct, are used to control flow separation and engine face distortion. The design of vortex generator installations in an inlet is defined as a problem addressable by numerical optimization techniques. A performance parameter is suggested to account for both inlet distortion and total pressure loss at a series of design flight conditions. The resulting optimization problem is difficult since some of the design parameters take on integer values. If numerical procedures could be used to reduce multimillion dollar development test programs to a small set of verification tests, numerical optimization could have a significant impact on both cost and elapsed time to design new aircraft.

Anderson, Bernhard H.↗

NASA NTRS2017

Model-Based Thermal System Design Optimization for the James Webb Space Telescope

Spacecraft thermal model validation is normally performed by comparing model predictions with thermal test data and reducing their discrepancies to meet the mission requirements. Based on thermal engineering expertise, the model input parameters are adjusted to tune the model output response to the test data. The end result is not guaranteed to be the best solution in terms of reduced discrepancy and the process requires months to complete. A model-based methodology was developed to perform the validation process in a fully automated fashion and provide mathematical bases to the search for the optimal parameter set that minimizes the discrepancies between model and data. The methodology was successfully applied to several thermal subsystems of the James Webb Space Telescope (JWST). Global or quasiglobal optimal solutions were found and the total execution time of the model validation process was reduced to about two weeks. The model sensitivities to the parameters, which are required to solve the optimization problem, can be calculated automatically before the test begins and provide a library for sensitivity studies. This methodology represents a crucial commodity when testing complex, large-scale systems under time and budget constraints. Here, results for the JWST Core thermal system will be presented in detail.

Cataldo, Giuseppe↗