Search NASA⌕ Search

SEARCH · Search NASA

Results for “RANDOM PHASE APPROXIMATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

An Investigation into Solution Verification for CFD-DEM

This report presents the study of the convergence behavior of the computational fluid dynamicsdiscrete element method (CFD-DEM) method, specifically National Energy Technology Laboratory’s (NETL) open source MFiX code (MFiX-DEM) with a diffusion based particle-tocontinuum filtering scheme. In particular, this study focused on determining if the numerical method had a solution in the high-resolution limit where the grid size is smaller than the particle size. To address this uncertainty, fixed particle beds of two primary configurations were studied: i) fictitious beds where the particles are seeded with a random particle generator, and ii) instantaneous snapshots from a transient simulation of an experimentally relevant problem. Both problems considered a uniform inlet boundary and a pressure outflow. The CFD grid was refined from a few particle diameters down to 1/6 th of a particle diameter. The pressure drop between two vertical elevations, averaged across the bed cross-section was considered as the system response quantity of interest. A least-squares regression method was used to extrapolate the grid-dependent results to an approximate “grid-free” solution in the limit of infinite resolution. The results show that the diffusion based scheme does yield a converging solution. However, the convergence is more complicated than encountered in simpler, single-phase flow problems showing strong oscillations and, at times, oscillations superimposed on top of globally non-monotonic behavior. The challenging convergence behavior highlights the importance of using at least four grid resolutions in solution verification problems so that (over-determined) regression-based extrapolation methods may be applied to approximate the grid-free solution. The grid-free solution is very important in solution verification and VVUQ exercise in general as the difference between it and the reference solution largely determines the numerical uncertainty. By testing different randomized particle configurations of the same general problem (for the fictitious case) or different instances of freezing a transient simulation, the numerical uncertainties appeared to be on the same order of magnitude as ensemble or time averaging uncertainties. By testing different drag laws, almost all cases studied show that model form uncertainty in this one, very important closure relation was larger than the numerical uncertainty, at least with a reasonable CFD grid, roughly five particle diameters. In this study, the diffusion width (filtering length scale) was mostly set at a constant of six particle diameters. A few exploratory tests were performed to show that similar convergence behavior was observed for diffusion widths greater than approximately two particle diameters. However, this subject was not investigated in great detail because determining an appropriate filter size is really a validation question which must be determined by comparison to experimental or highly accurate numerical data. Future studies are being considered targeting solution verification of transient simulations as well as validation of the filter size with direct numerical simulation data.

97 MATHEMATICS AND COMPUTING↗

Formation of Amorphous Carbon Multi‐Walled Nanotubes from Random Initial Configurations

Amorphous carbon nanotubes (a‐CNT) with up to four walls and sizes ranging from 200 to 3200 atoms have been simulated, starting from initial random configurations and using the Gaussian Approximation Potential. The important variables (like density, height, and diameter) required to successfully simulate a‐CNTs were predicted with the machine learning random forest technique. The width of the a‐CNT models ranged between 0.55–2 nm with an average inter‐wall spacing of 0.31 nm. The topological defects in a‐CNTs were analyzed and new defect configurations were observed. The electronic density of states and localization in these phases were discussed and delocalized electrons in the π subspace were identified as an important factor for inter‐layer cohesion. Spatial projection of the electronic conductivity favors axial transport along connecting hexagons, while non‐hexagonal parts of the network either hinder or bifurcate the electronic transport. A vibrational density of states was calculated and is potentially an experimentally comparable fingerprint of the material. The appearance of a low‐frequency radial breathing mode was discussed and the thermal conductivity at 300 K was estimated using the Green‐Kubo formula.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lower hybrid wavepacket stochasticity revisited

Analysis is presented in support of the explanation in Ref. [1] for the observation of relativistic electrons during Lower Hybrid (LH) operation in EC pre-heated plasma at the WEGA stellarator [1,2]. LH power from the WEGA TE11 circular waveguide, 9 cm diameter, un-phased, 2.45 GHz antenna, is radiated into a B≅0.5 T, М„n{sub e}≅5×10{sup 17} 1/m{sup 3} plasma at T{sub e}≅10 eV bulk temperature with an EC generated 50 keV component [1]. The fast electrons cycle around flux or drift surfaces with few collisions, sufficient for randomizing phases but insufficient for slowing fast electrons down, and thus repeatedly interact with the rf field close to the antenna mouth, gaining energy in the process. Our antenna calculations reveal a standing electric field pattern at the antenna mouth, with which we formulate the electron dynamics via a relativistic Hamiltonian. A simple approximation of the equations of motion leads to a relativistic generalization of the area-preserving Fermi-Ulam (F-U) map [3], allowing phase-space global stochasticity analysis. At typical WEGA plasma and antenna conditions, the F-U map predicts an LH driven current of about 230 A, at about 225 W of dissipated power, in good agreement with the measurements and analysis reported in [1].

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Porting Classical Approaches for Quantum Simulations to Quantum Computers

Simulating quantum many-body systems is one of the most promising problems in which we might anticipate that quantum computers should show quantum advantage. Unfortunately, there is still a gap between this promise and actual practice. New quantum algorithms need to be developed and the current quantum algorithms have various difficulties - e.g efficient state preparation - which must be overcome and improved upon. In many cases, classical approaches need to be ported over to quantum devices. In this project we have developed a suite of new quantum algorithms which makes progress in this regard. We developed a new optimization scheme for variational quantum eigensolvers, UBOS, which mitigates problems with local minimas and barren plateaus while improving convergence to the ground state by an order of magnitude. We developed a new way to utilize qubitization to find ground states of nearly frustration-free Hamiltonians faster than all previous methods. We developed a series of state preparation techniques which helps initialize parameterized quantum circuits into reasonable starting points on which quantum algorithms are then applied. In addition to the development of novel algorithms, it is critical to have classical simulation techniques for approximately simulating quantum circuits which can be used to benchmark and understand quantum algorithms. Toward that end, we developed a novel POVM formalism to simulate quantum circuits as well as exemplify the massive parallelization of tensor network methodologies. Finally, we developed physical understanding of entanglement phase transitions such as many-body localization and random tensor networks.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Statistical model of exotic rotational correlations in emergent space-time

A statistical model is formulated to compute exotic rotational correlations that arise as inertial frames and causal structure emerge on large scales from entangled Planck scale quantum systems. Noncommutative quantum dynamics are represented by random transverse displacements that respect causal symmetry. Entanglement is represented by covariance of these displacements in Planck scale intervals defined by future null cones of events on an observer's world line. Light that propagates in a nonradial direction inherits a projected component of the exotic rotational correlation that accumulates as a random walk in phase. A calculation of the projection and accumulation leads to exact predictions for statistical properties of exotic Planck scale correlations in an interferometer of any configuration. The cross-covariance for two nearly co-located interferometers is shown to depart only slightly from the autocovariance. Specific examples are computed for configurations that approximate realistic experiments, and show that the model can be rigorously tested.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Some Considerations on Stochastic Neutron Populations

The neutron population in a multiplying body containing a weak random source may depart considerably from its average or expected value. The resulting behavior of the system is then unpredictable, and a fully stochastic description of the neutron population becomes necessary. Stochastic considerations are especially important when dealing with pulsed reactors or in the case of criticality excursions in the presence of a weak source. Using the theory of discrete-state continuous-time Markov processes, and subject to some physical approximations, Bell obtained approximate solutions for the neutron number probability distributions (pdf), with and without an intrinsic random neutron source, that were valid at late times and/ large neutron populations. In recent work, we obtained exact solutions for Bell's model problem, and in this paper we use these exact probability distributions to: (I) assess the accuracy of Bell's asymptotic solutions and show how the latter follow from the exact solutions, (2) rigorously examine the probability of obtaining a divergent chain reaction, and (3) demonstrate the existence of an abrupt transition from a stochastic to a deterministic phase with increasing source strength.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluating diffusion and the thermodynamic factor for binary ionic mixtures

Molecular dynamics (MD) simulations are a powerful tool for the calculation of transport properties in mixtures. Not only are MD simulations capable of treating multicomponent systems, they are also applicable over a wide range of temperatures and densities. In plasma physics, this is particularly important for applications such as inertial confinement fusion. While many studies have focused on the effect of plasma coupling on transport properties, here we focus on the effects of mixing. We compute the thermodynamic factor, a measure of ideal/non-ideal mixing, for three binary ionic mixtures. Here, we consider mixtures of hydrogen and carbon, hydrogen and argon, and argon and carbon, each at 500 randomly generated state points in the warm dense matter and plasma regimes. The calculated thermodynamic factors indicate different mixing behavior across phase space, which can significantly affect the corresponding mutual diffusion coefficients. As MD simulations are still computationally expensive, we apply modern data science tools to predict the thermodynamic factor over a large phase space. Further, we propose a more accurate approximation to the mutual diffusion coefficient than the commonly applied Darken relation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ring of BEC pools as a trap for persistent flow

Mott insulator-superfluid transition in a periodic lattice of Josephson junctions can be driven by tunneling rate increase. The resulting winding numbers W of the condensate wave function decrease with increasing quench time in accord with the Kibble-Zurek mechanism (KZM). However, in very slow quenches, Bose-Hubbard dynamics rearranges the wave-function phase so that its random walk cools, W{sup 2} decreases and eventually the wave function becomes too cold to overcome potential barriers separating different W. Thus, in contrast with KZM, in very slow quenches W{sup 2} is set by random walk with ''critical'' step size, independently of {tau}{sub Q}. As our study requires use of the truncated Wigner approximation (TWA) over relatively long time intervals, we investigate the validity of TWA by comparing its predictions with exact calculations for suitably small quantum systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pass-efficient methods for compression of high-dimensional turbulent flow data

The future of high-performance computing, specifically on future Exascale computers, will presumably see memory capacity and bandwidth fail to keep pace with data generated, for instance, from massively parallel partial differential equation (PDE) systems. Current strategies proposed to address this bottleneck entail the omission of large fractions of data, as well as the incorporation of in situ compression algorithms to avoid overuse of memory. To ensure that post-processing operations are successful, this must be done in a way that a sufficiently accurate representation of the solution is stored. Moreover, in situations where the input/output system becomes a bottleneck in analysis, visualization, etc., or the execution of the PDE solver is expensive, the number of passes made over the data must be minimized. In the interest of addressing this problem, this work focuses on the utility of pass-efficient, parallelizable, low-rank, matrix decomposition methods in compressing high-dimensional simulation data from turbulent flows. Additionally, a particular emphasis is placed on using coarse representation of the data – compatible with the PDE discretization grid – to accelerate the construction of the low-rank factorization. This includes the presentation of a novel single-pass matrix decomposition algorithm for computing the so-called interpolative decomposition. The methods are described extensively and numerical experiments on two turbulent channel flow data are performed. In the first (unladen) channel flow case, compression factors exceeding 400 are achieved while maintaining accuracy with respect to first- and second-order flow statistics. In the particle-laden case, compression factors of 100 are achieved and the compressed data is used to recover particle velocities. These results show that these compression methods can enable efficient computation of various quantities of interest in both the carrier and disperse phases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Delving into the depths of NGC 3783 with XRISM

The 2024 X-ray/UV observation campaign of NGC 3783, led by XRISM, revealed the launch of an ultrafast outflow (UFO) with a radial velocity of 0.19c (57 000 km s −1 ). This event is synchronized with the sharp decay, within less than half a day, of a prominent soft X-ray/UV flare. Accounting for the look-elsewhere effect, the XRISM Resolve data alone indicate a low probability of 2 × 10 −5 that this UFO detection is due to random chance. The UFO features narrow H-like and He-like Fe lines with a velocity dispersion of ∼1000 km s −1 , suggesting that it originates from a dense clump. Beyond this primary detection, there are hints of weaker outflow signatures throughout the rise and fall phases of the soft flare. Their velocities increase from 0.05c to 0.3c over approximately three days, and they may be associated with a larger stream in which the clump is embedded. The radiation pressure is insufficient to drive the acceleration of this rapidly evolving outflow. The observed evolution of the outflow kinematics instead closely resembles that of solar coronal mass ejections, implying magnetic driving and, conceivably, reconnection near the accretion disk as the likely mechanisms behind both the UFO launch and the associated soft flare.

Astronomy and AstroPhysics↗

High‐speed 4‐dimensional scanning transmission electron microscopy using compressive sensing techniques

Abstract Here we show that compressive sensing allows 4‐dimensional (4‐D) STEM data to be obtained and accurately reconstructed with both high‐speed and reduced electron fluence. The methodology needed to achieve these results compared to conventional 4‐D approaches requires only that a random subset of probe locations is acquired from the typical regular scanning grid, which immediately generates both higher speed and the lower fluence experimentally. We also consider downsampling of the detector, showing that oversampling is inherent within convergent beam electron diffraction (CBED) patterns and that detector downsampling does not reduce precision but allows faster experimental data acquisition. Analysis of an experimental atomic resolution yttrium silicide dataset shows that it is possible to recover over 25 dB peak signal‐to‐noise ratio in the recovered phase using 0.3% of the total data. Lay abstract : Four‐dimensional scanning transmission electron microscopy (4‐D STEM) is a powerful technique for characterizing complex nanoscale structures. In this method, a convergent beam electron diffraction pattern (CBED) is acquired at each probe location during the scan of the sample. This means that a 2‐dimensional signal is acquired at each 2‐D probe location, equating to a 4‐D dataset. Despite the recent development of fast direct electron detectors, some capable of 100kHz frame rates, the limiting factor for 4‐D STEM is acquisition times in the majority of cases, where cameras will typically operate on the order of 2kHz. This means that a raster scan containing 256^2 probe locations can take on the order of 30s, approximately 100‐1000 times longer than a conventional STEM imaging technique using monolithic radial detectors. As a result, 4‐D STEM acquisitions can be subject to adverse effects such as drift, beam damage, and sample contamination. Recent advances in computational imaging techniques for STEM have allowed for faster acquisition speeds by way of acquiring only a random subset of probe locations from the field of view. By doing this, the acquisition time is significantly reduced, in some cases by a factor of 10‐100 times. The acquired data is then processed to fill‐in or inpaint the missing data, taking advantage of the inherently low‐complex signals which can be linearly combined to recover the information. In this work, similar methods are demonstrated for the acquisition of 4‐D STEM data, where only a random subset of CBED patterns are acquired over the raster scan. We simulate the compressive sensing acquisition method for 4‐D STEM and present our findings for a variety of analysis techniques such as ptychography and differential phase contrast. Our results show that acquisition times can be significantly reduced on the order of 100‐300 times, therefore improving existing frame rates, as well as further reducing the electron fluence beyond just using a faster camera.

Robinson, Alex W.↗

Non-power law behavior of the radial profile of phase-space density of halos

We study the pseudo phase-space density, ρ(r)/σ{sup 3}(r), of ΛCDM dark matter halos with and without baryons (baryons+DM, and pure DM), by using the model introduced in Del Popolo (2009), which takes into account the effect of dynamical friction, ordered and random angular momentum, baryons adiabatic contraction and dark matter baryons interplay. We examine the radial dependence of ρ(r)/σ{sup 3}(r) over 9 orders of magnitude in radius for structures on galactic and cluster of galaxies scales. We find that ρ(r)/σ{sup 3}(r) is approximately a power-law only in the range of halo radius resolved by current simulations (down to 0.1% of the virial radius) while it has a non-power law behavior below the quoted scale, with inner profiles changing with mass. The non-power-law behavior is more evident for halos constituted both of dark matter and baryons while halos constituted just of dark matter and with angular momentum chosen to reproduce a Navarro-Frenk-White (NFW) density profile, are characterized by an approximately power-law behavior. The results of the present paper lead to conclude that density profiles of the NFW type are compatible with a power-law behavior of ρ(r)/σ{sup 3}(r), while those flattening to the halo center, like those found in Del Popolo (2009) or the Einasto profile, or the Burkert profile, cannot produce radial profile of the pseudo-phase-space density that are power-laws at all radii. The results argue against universality of the pseudo phase-space density and as a consequence argue against universality of density profiles constituted by dark matter and baryons as also discussed in Del Popolo (2009)

79 ASTRONOMY AND ASTROPHYSICS↗

Stabilities and defect-mediated lithium-ion conduction in a ground state cubic Li 3 N structure

A stable ground state structure with cubic symmetry of Li 3 N (c-Li 3 N) is found by ab initio initially symmetric random-generated crystal structure search method. Gibbs free energy, calculated within quasi-harmonic approximation, shows that c-Li 3 N is the ground state structure for a wide range of temperature. The c-Li 3 N structure has a negative thermal expansion coefficient at temperatures lower than room temperature, due mainly to two transverse acoustic phonon modes. This c-Li 3 N phase is a semiconductor with an indirect band gap of 1.90 eV within hybrid density functional calculation. We also investigate the migration and energetics of native point defects in c-Li 3 N, including lithium and nitrogen vacancies, interstitials, and anti-site defects. Lithium interstitials are found to have a very low migration barrier (~0.12 eV) and the lowest formation energy among all possible defects. Thus, the ionic conduction in c-Li 3 N is expected to occur via an interstitial mechanism, in contrast to that in the well-known α-Li 3 N phase which occurs via a vacancy mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Selective-area growth and magnetic characterization of MnAs/AlGaAs nanoclusters on insulating Al{sub 2}O{sub 3} layers crystallized on Si(111) substrates

We report on selective-area metal-organic vapor phase epitaxy and magnetic characterization of coupled MnAs/AlGaAs nanoclusters formed on thin Al{sub 2}O{sub 3} insulating layers crystallized on Si(111) substrates. Cross-sectional transmission electron microscopy reveals that poly-crystalline γ-Al{sub 2}O{sub 3} grains are formed after an annealing treatment of the amorphous Al{sub 2}O{sub 3} layers deposited by atomic layer deposition on Si(111) substrates. The 〈111〉 direction of the γ-Al{sub 2}O{sub 3} grains tends to be oriented approximately parallel to the 〈111〉 direction of the Si substrate. We observe that hexagonal MnAs nanoclusters on AlGaAs buffer layers grown by selective-area metal-organic vapor phase epitaxy on partially SiO{sub 2}-masked Al{sub 2}O{sub 3} insulator crystallized on Si(111) substrates are oriented with the c-axis along the 〈111〉 direction of the substrates, but exhibit a random in-plane orientation. A likely reason is the random orientation of the poly-crystalline γ-Al{sub 2}O{sub 3} grains in the Al{sub 2}O{sub 3} layer plane. Magnetic force microscopy studies at room temperature reveal that arrangements of coupled MnAs nanoclusters exhibit a complex magnetic domain structure. Such arrangements of coupled MnAs nanoclusters may also show magnetic random telegraph noise, i.e., jumps between two discrete resistance levels, in a certain temperature range, which can be explained by thermally activated changes of the complex magnetic structure of the nanocluster arrangements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Method for Obtaining Liquid–Solid Adsorption Rates from Molecular Dynamics Simulations: Applied to Methanol on Pt(111) in H 2 O

Adsorption is an important step in heterogeneous catalysis as it predetermines how many reactant molecules can participate in a surface reaction per unit time. While the rate of adsorption processes is well studied in gas–solid adsorption in both theory and experiment, such rates are still not well studied for liquid–solid adsorption. This is partly because the ever-changing configurations of liquid-phase solvent molecules impede the ability to study a molecule approaching a surface from a liquid phase by either experiment or theory. In this work, we develop a method using molecular dynamics (MD) simulations to study the rate of adsorption in liquid–solid adsorption processes. Specifically, we use MD to model the diffusion of a methanol molecule in aqueous solvent and its adsorption to a Pt(111) surface. We find that by approximating the solute motion as following the same displacement rates as a random walk model, the adsorbed and non-adsorbed states of the methanol molecule near the Pt(111) surface can be discerned and quantified. In particular, this methodology enables extracting a sticking coefficient and a macroscopically relatable adsorption rate. This method can be applied to arbitrary types of reactants and surfaces, as well as different liquid environments, thus providing a general tool for predicting quantitative adsorption rates of liquid–solid adsorption systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Time evolution of the distribution function for stochastically heated relativistic electrons in a laser field of picosecond duration

We report a numerical analysis of the stochastic acceleration of electrons, stipulated by a random change in the phase of the force acting on the electron. The main source of randomness is the random spatial distribution of electromagnetic fields in the focal region of multimode laser radiation. A typical frequency of the random phase change corresponding to the maximum impact of the effect under consideration lies in the range of (0.25–0.5)ν (ν is the radiation frequency of a neodymium laser). A wave packet model convenient for calculations taking into account the radiative transitions of the neodymium ion is proposed. The dependence of the average energy of relativistic electrons on the flux density in the range of 10{sup 15}–10{sup 18} W cm{sup -2} is calculated. The time dependence of the average electron energy during the laser pulse in the form of approximating formulas is constructed. The typical time for the development of stochastic heating of electrons is determined. It is found that the stochastic acceleration process weakly depends on the laser pulse duration, when the latter exceeds several hundred periods of the electromagnetic wave. (interaction of laser radiation with matter. laser plasma)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Towards robust surrogate models: Benchmarking machine learning approaches to expediting phase field simulations of brittle fracture

Data-driven approaches have the potential to make modeling complex, nonlinear physical phenomena significantly more computationally tractable. For example, computational modeling of fracture is a core challenge where machine learning techniques have the potential to provide a much needed speedup that would enable progress in areas such as multi-scale modeling and uncertainty quantification. Currently, phase field modeling (PFM) of fracture is one such approach that offers a convenient variational formulation to model crack nucleation, branching and propagation. To date, machine learning techniques have shown promise in approximating PFM simulations. While standard fracture benchmarks represent realistic scenarios frequently observed in practice, they typically do not provide sufficiently challenging tests for data-driven methods. Here, to address this gap, we introduce a challenging dataset based on PFM simulations designed to benchmark and advance ML methods for fracture modeling. This dataset includes three energy decomposition methods, two boundary conditions, and 1000 random initial crack configurations for a total of 6000 simulations. Each sample contains 100 time steps capturing the temporal evolution of the crack field. Alongside this dataset, we also implement and evaluate Physics Informed Neural Networks (PINN), Fourier Neural Operators (FNO), and UNet models as baselines, and explore the impact of ensembling strategies on prediction accuracy. With this combination of our dataset and baseline models drawn from the literature we aim to provide a standardized and challenging benchmark for evaluating machine learning approaches to solid mechanics. Our results highlight both the promise and limitations of popular current models, and demonstrate the utility of this dataset as a testbed for advancing machine learning in fracture mechanics research.

Benchmark dataset↗

On the validation of seismic imaging methods: Finite frequency or ray theory?

Abstract We investigate the merits of the more recently developed finite‐frequency approach to tomography against the more traditional and approximate ray theoretical approach for state of the art seismic models developed for western North America. To this end, we employ the spectral element method to assess the agreement between observations on real data and measurements made on synthetic seismograms predicted by the models under consideration. We check for phase delay agreement as well as waveform cross‐correlation values. Based on statistical analyses on S wave phase delay measurements, finite frequency shows an improvement over ray theory. Random sampling using cross‐correlation values identifies regions where synthetic seismograms computed with ray theory and finite‐frequency models differ the most. Our study suggests that finite‐frequency approaches to seismic imaging exhibit measurable improvement for pronounced low‐velocity anomalies such as mantle plumes.

58 GEOSCIENCES↗