Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reference Model 6”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

724 records · Page 41

Development and Testing of Pulse Guns for Combustion Instability Testing

To test liquid rocket engines (LREs) for combustion instabilities, devices such as bombs are often used to create pressure wave disturbances. Bombs, while effective, are inherently dangerous, expensive, and difficult to procure. Over the years, pulse guns have been used as a safer and more cost-effective way to generate controlled pressure disturbances in engine chambers. In anticipation of the need for stability testing of prototype LREs at NASA Marshall Space Flight Center (MSFC), a set of pulse guns have been designed, fabricated, tested, and characterized. The pulse gun program is funded by the RS-25 Engine Program managed out of MSFC and funded by NASA’s Space Launch System (SLS) through the MSFC Liquid Engines Office (LEO). A pulse gun is a simple device – like a traditional gun, it has a breech and barrel section. However, unlike a traditional gun, there is no bullet, as the purpose of the pulse gun is strictly to fire a high pressure pulse. Instead of a firing pin and primer that would normally be used in a traditional gun, an initiator is used to activate the gun powder. The initiator is a highly reliable pyrotechnic initiator. For this study, clone versions of the NASA Standard Initiator (NSI) were used. The initiator is used to ignite a pre-measured amount of gun powder loaded into the breech. When the pressure of the burnt gun powder exceeds the set point of a downstream burst disk, the disk ruptures, allowing the high pressure pulse to travel downstream through the barrel section. A ballistic pressure transducer located in the breech section is used to measure the short duration, high pressure pulse. Some configurations of the pulse gun have barrel sections that include one or more additional ballistic pressure transducers. These additional pressure measurements help track the degradation and damping of the pulse as it travels out of the barrel section. The measurements may also be used to determine the velocity of pulse. The objective of this paper is to present the different variants of this newly-developed pulse gun and characterize performance over a range of parameters. The parameters include breech diameter, barrel length, amount of gun powder used, the way the gun powder is packed, and the pressure setting of the burst disk. There are a total of six pulse guns: three with the 0.25 inch breech and three different length barrels, and three with the 0.40 inch breech and three different length barrels. For both breech sizes, the associated barrels are referred to as standard, one-port, and two-port barrels. The standard barrel has no instrumentation and is likely the barrel that will be used for engine stability testing. The one- and two-port barrels were designed specifically for pulse gun component testing to allow measurements of the magnitude and timing of the high pressure pulse as it makes its way through the pulse gun. The burst disks tested were commercially-available burst disks designed to rupture at 8,000, 16,000, and 24,000 psid. Testing was accomplished by firing the pulse gun into a test chamber pressurized with nitrogen at about 2300 psig. A total of four Model 113B23 High frequency ICP® pressure sensors (10k psi) were mounted in the test chamber, in the same plane as the pulse gun. Two of the sensors had “trimmed” adapters, and two did not. Given the symmetrical configuration of the sensors within the test chamber, different amplitudes of pressure measurements are attributed to the use of trimmed versus untrimmed adapters. The untrimmed adapters, with their narrower passages, tended to amplify the pressure amplitudes by as much as 50%. In total, 41 pulse gun tests have been conducted.Data are still being analyzed, but some trends are apparent. For example, measurements taken within the pulse gun are shown in Figures 3 and 4 for Hot-fires (HFs) # 11 and 39, respectively. Both tests were identical in that the 0.40 inch ID breech, two-port barrel, 8,000 psid burst disk, and same amount of gunpowder (6.639 grains for HF# 11, and 6.576 grains for HF# 39) were used, and the back pressure in the nitrogen test chamber was ~2300 psig. Despite keeping all these variables constant, the results from these two tests look quite different. For both tests, the first pressure peak shown in the P2111 trace within the breech is the firing of the initiator. The second peak and any subsequent peaks are from the combustion of the gunpowder. It should be noted that because the sensors are dynamic, the ~2300 psig baseline static pressure is not shown in the figures. For HF# 11, the burst disk clearly ruptured in a little over 0.1 ms from the time the initiator was fired. This is evident from the abrupt rise in pressure for P2112 followed by another abrupt rise in pressure for P2113. The sensors track the movement of the high pressure pulse through the pulse gun. For HF# 39, however, there was nearly 1 ms delay between the initiator firing and the burst disk rupturing. The only difference between these two tests was the way in which the gunpowder was packed within the breech. For HF# 11, the gunpowder was poured directly into the breech, atop the initiator, and held in place with a vegetable fiber wad appropriately sized for the barrel diameter. Once in place, the wad firmly held the gunpowder in place. For HF# 39, the gunpowder was rolled within cigarette paper with the ends of the paper twisted. The rolled gunpowder was gently pushed down into the breech, toward the initiator, and no wad was used. This method of loading the gunpowder consistently produced longer delays in the rupture of the burst disk, presumably because there was a steady, fuller burning of the gunpowder. The burst disk was rated for 8,000 psid, which means that the burst disk should not have opened until the pressure in the breech reached ~10,300 since there was ~2300 psig back pressure in the test chamber. In the case of HF# 11, the breech pressure only reached roughly 4200 psi before there was leakage either through or past the burst disk, but for HF#39, the breech pressure reached 10,600 psi prior to the burst disk opening. The temperature of the burst disk is certainly a factor in determining when the burst disk will rupture. A sharp rise in the burst disk temperature could weaken it and cause it to stray from the designed set point burst pressure. The burst disks are manufactured of Inconel to try to reduce their sensitivity to temperature, but how the burst disks perform above 900°F is not documented. All burst disks were engineered and tested by the manufacturer for ambient temperature conditions. One theory for why rolling the gunpowder in cigarette paper may produce better results is related to a more controlled temperature environment. The cigarette paper may act as a sheath that protects the burst disk from excessive temperatures during the rapid buildup of pressure in the breech. The ultimate benefit of not breeching the burst disk prematurely is shown in Figures 5 and 6, which graphs the resultant pressure pulse produced in the test chamber. For HF #11, the peak pressure on the P2123 trimmed adapter is about 270 psi, while for HF# 39 it is 343 psi, which is about 1.27 times greater in magnitude. In either case, the pressure pulse is ~20 μs in width once it reaches the test chamber. Another pressure rise about 100 μs later can be seen on the sensors located across from the pulse gun port, P2124 and P2121. These pressures are lower due to attenuation of the pressure wave as it moves across the test chamber. After the wave encounters the wall, it reflects back and forth within the chamber until it completely dissipates.

Pulse Gun↗

VERNE: Revealing the Mysteries and Histories of Venus

Introduction: The three Venus missions that were recently selected for upcoming flight (VERITAS, DAVINCI+, and EnVision) will be incredibly valuable to our understanding of Venus’ history, geology, and atmosphere. However, even once completed, key gaps in our knowledge of Venus, and more generally the formation and active processes on rocky, Earth-like planets, will still persist. Remaining questions include 1) how global intrinsic magnetic fields might be maintained on rocky worlds, and how they could then go extinct, and 2) what role atmospheric sulfur chemistry plays in climates of Earth-like planets, which is an increasingly timely subject as Earth’s own atmospheric sulfur content is climbing due to human activity. These questions require in-situ observations from Venus’ cloud deck, at the altitudes at which the UV absorber exists. The Venus Environment Research and Novel Exploration (VERNE) mission will address these questions with an aerial platform that will drift around the equatorial region of the planet for 9 days. VERNE will collect data to determine the identity of the mysterious UV absorber, while also taking magnetic field measurements over the tesserae, the regions on Venus that are most likely to retain remanent crustal magnetization, in order to understand the potential role of a past intrinsically-generated global magnetic field on Venus. Mission Objectives: The two major science objectives that drive the VERNE mission are: 1) Determine the identity of the Venusian unknown ultraviolet absorber(s). First observed approximately a century ago [1], the composition of Venus’ ultraviolet (UV) absorber is one of the oldest mysteries in Venus atmospheric chemistry [2,3]. While several candidate UV absorbers (mostly sulfur species) have been proposed, no consensus has been reached on its composition and its specific interactions with the atmosphere. Determining the identity of the UV absorber will aid climate models by showing how and where incident solar energy is absorbed by the atmosphere and make progress towards understanding the chemical and energetic processes taking place above Venus’ upper cloud deck [4]. 2) Determine if Venus retains evidence of a past, internally-generated magnetic field. While Venus does not currently have an intrinsically-generated magnetic field, evidence for the existence of a past field on Venus and a timeline of its decay will fill in a more holistic picture of the evolution of Venus’ geological record and atmosphere. As the oldest geologic units on the surface, Venus’ tesserae may still have remanent crustal magnetization signatures within the rocky composition [5]. In any case, the signatures detected will provide insight into Venus’ past geological and core dynamo activity. Mission Summary: VERNE includes a 3-part flight system made up of 1) an entry system with a HEEET (Heatshield for Extreme Entry Environment Technology) aeroshell, 2) an orbiter for data relay, and 3) an in-situ balloon and gondola. After entry into Venus’ atmosphere, the balloon will be deployed within the upper cloud deck, at an altitude of 62 km, over a tesserae region. The in-situ data collection will last for the duration of 2 full circumnavigations of the planet, which will take ~9 days. Instrumentation Suite: The four instruments that comprise VERNE’s instrument payload will enable the identification of the unknown UV absorber and the detection of remanent crustal magnetization if it exists in the tesserae. The proposed instrument suite cycle during mission operations is shown in Fig. 1. The four instruments are described below: 1) Adams (ion neutral mass spectrometer) has a range of 18-257 AMU and will detect and distinguish the mixing ratios of O₂, H₂O, H₂SO₄, S, S₂, S₃, S₄, S₅, S₆, S₇, S₈, SO, SO₂, OSSO, SO₃, Cl₂, FeCl₃ and other trace sulfur and organic species. The spatial (longitudinal) and temporal (day/night) variations will be observed throughout 2 circumnavigations with a sample cadence of 12 minutes. 2) Shelley (nephelometer) will determine the size distribution of the aerosols (0.4 to 36 um) in the atmosphere. With a size resolution of <0.7 um, it can determine which mode of H2SO4 is present and characterize the large (>30 um) organic particles previously detected by the Venera and Galileo missions [6,7]. 3) Herbert (UV imager) will measure UV radiance at 283 nm (the wavelength of SO2 absorption) and 365 nm (the unknown part of the absorber). UV images will be taken concurrently with the INMS and nephelometer to correlate UV absorption with abundances of the UV absorber species. 4) Vonnegut (magnetometer) has a range of >600 nT and a precision and accuracy of 1 nT. If magnetized by a past field, the crust may have retained a magnetization of up to 3 A/m2 [5]. With a noise floor of 10 nT, the magnetometer will be able to detect RCM from an altitude of 62 km, even if the thickness of the magnetized crust is just 1 km (Fig. 2). Mission Concept Design: VERNE will be launched with a mass of 3300 kg in an intermediate-high performance class vehicle with a 4-m fairing. The 475-day mission includes 466 days for the cruise, coasting, and orbit initialization phases before entry, descent, and balloon deployment. During the 9-day science phase, the aerial platform will make 2 circumnavigations of the planet at an altitude of 62 km. The INMS and the nephelometer will acquire data for 2 hours during the daytime and nighttime during each circumnavigation, while the UV imager will be on for the duration of the daytime, and the magnetometer will be operational throughout the entirety of the science phase. Data will be stored and processed with the JPL-designed Sphinx command and data handling system. Data will be sent from the balloon to the orbiter using an S-band relay link, stored on the orbiter, and then forwarded to Earth where it will be received by the DSN. Conclusion: VERNE will fill key gaps in our understanding of the history and ongoing processes related to the geology and atmosphere of Venus and rocky worlds in general. Even with adequate flight system contingencies and expected costs below the $900M New Frontiers cost cap, VERNE is not without its risks and challenges. Further trade spaces to explore include 1) using solely battery power vs. including solar panels to increase the mission duration and 2) investigating the use of lightweight materials and 3D-printed structures to reduce the gondola mass, among others. Acknowledgments: We would like to thank the JPL Planetary Science Summer School, especially our mentors Troy Hudson, Karl Mitchell, and Leslie Lowes, as well as our Team-X study lead Al Nash and the members of Team-X. We’d additionally like to thank our review panel for asking insightful questions and providing valuable feedback. References: [1] Ross, F. E. (1928) Astrophysical J., 68, 57-92. [2] Rossow, W. B. et al. (1980) J. Geophysical Research, 85, 8107-8128. [3] Pinto, J. P. et al. (2021) Nature Communications, 12, 175. [4] Titov, D. V. et al. (2007) Cosmic Research, 21, 401. [5] O’Rourke, J. et al. (2019) Geophysical Research Lett., 46, 5768–5777. [6] Limaye, S. S. et al. (2018) Astrobiology, 18(9), 1181-1198. [7] Grinspoon, D. H. et al. (2013) Planetary and Space Sci., 41(7), 515-542. [8] Parker, R. L. (2003) J. Geophysical Research, 108, 5006. *The cost information contained in this document is of a budgetary and planning nature and is intended for informational purposes only. It does not constitute a commitment on the part of JPL and/or Caltech.

H Alpert↗

A Combined Al-Mg/Pb-Pb Age of the Solar System

Astrophysical models of planet formation and protoplanetary disk evolution demand precise and accurate timing of the sequence of events in the solar nebula, relative to a time t=0, usually taken to be during the short epoch of CAI (Ca-rich, Al-rich inclusion) formation. Most CAIs formed withlive26Al (mean-life τ26= 1.034 Myr [1]), with an abundance 26Al/27Al ≈ (26Al/27Al)SS= 5.23 × 10-5[2]. We adopt this as the widespread level of 26Al in the solar nebula at t=0. Assuming spatial homogeneity of 26Al, an inclusion that had less 26Al, (26Al/27Al)0, formed a time Δt26= τ26ln[(26Al/27Al)SS/ (26Al/27Al)0] after t=0.These ages are typical precise to within ±0.1 Myr. Igneous bulk meteorites and inclusions can be relatively dated by the Al-Mg chronometer, but only ifΔt26<6 Myr. The Pb-Pb system is useful as a longer relative chronometer. It yields absolute ages tPb using 207Pb/206Pb, 206Pb/204Pb, and 238U/235U ratios measured indifferent portions of a sample, assuming certain half-lives [4]. These absolute ages are uncertain to within ±9 Myr due to uncertainties in the 235U half-life[3], but times of formation ΔtPb= tCAI–tPb relative to t=0, are more precise(±0.5Myr),iftCAI can be found. Here, tCAI means the Pb-Pb age that would be measured in CAIs using the half-lives the community typically uses, if they achieved isotopic closure at t=0. Unfortunately, direct Pb-Pb dating of CAIs has not definitively determined tCAI. Based on four CAIs with canonical (26Al/27Al)0,[5,6] found tPb= 4567.30 ± 0.16 Myr. No other CAI ages with measured 238U/235U have been reported in the refereed literature, but there are hints of other CAIs with ages tPb= 4568.0 ± 0.2 Myr [7] and tPb= 4568.3 ± 0.2 Myr [8].It is unclear whether anyof these igneous type B CAIs isotopically closed at t=0 or represents tCAI. Instead of measurements, we advocate finding tCAI by minimizing the discrepancies between the Al-Mg and Pb-Pb chronometers. Assuming Δt26=ΔtPb, we find the implied t’CAI= tPb+Δt26, then define t*CAIas the weighted mean of the t’CAI. t*CAIis the best guess for the Pb-Pb age of t=0; the assumption of homogeneity is justified if the t’CAI cluster within errors around t*CAI. This statistical approach is similar to, but improves on, that of[9]. We find t*CAI= 4568.73 ± 0.16 Myr. Below we discuss our methodology and the implications of this age for CAIs, 1.4 Myr older than the reported and typically used age 4567.30±0.16 Myr. Methods: We base our estimate of t*CAIon five achondrites for which published (26Al/27Al)0and Pb-Pb ages exist: the quenched angrites D’Orbigny, Sahara 99555 (SAH 99555), and Northwest Africa (NWA) 1670; the pseudo-eucrite Asuka 881394; and the inner disk achondrite. All are “NC” (non-carbonaceous) achondrites that likely cooled quickly enough that the Al-Mg and Pb-Pb systems achieved isotopic closure simultaneously. We also considered the “CC” (carbonaceous chondrite-like) achondrites NWA 2796 and NWA 6704, butdo not include them in our fit. Al-Mg and Pb-Pb seem not to have closed simultaneously, possibly because formation in the outer disk from volatile-rich composition led to slower cooling. Of the 8 chondrules from NWA 5697 measured by [20,21], we also consider the 4 for which 238U/235U was measured: 2-C1, 5-C2, 3-C5, 11-C1.Depending on their post-formation thermal histories, the Al-Mg and Pb-Pb systems in chondrules may or may not have closed simultaneously. Table 1: (26Al/27Al)0, Pb-Pb ages of selected samplesSample(26Al/27Al)0/ 10-6RefPb-PbRefD’Orbigny3.98±0.15104563.43±0.19♮10-12SAH 995553.64±0.18104563.88±0.2712NWA16705.92±0.59104564.39±0.24*10Asuka 88139413.1±0.5613-154564.98±0.1715NWA 73253.03±0.14164563.4±2.616NWA 27963.94±0.16174562.89±0.5917NWA 67043.03±0.14184562.76±0.26192-C17.56±1.53204567.57±0.56*215-C27.04±1.51204567.54±0.52*213-C58.85±1.83204566.20±0.63*2111-C15.55±1.84204565.84±0.72*21*regression based on one subset of data points ♮weighted mean of two datasets Pb-Pb ages are proportional to the intercept of the line formed by linear regression of 207Pb/206Pb vs. 206Pb/204Pb data from various washes, leachates and residues of acid dissolution of a sample. Because contamination by terrestrial or primordial Pb is pervasive, some fractions must be excluded from regressions to ensure a fit with acceptable mean squares weighted deviation (MSWD). Usually points are excluded based on low [Pb], or low 206Pb/204Pb ratio(low radiogenic component), with single outliers identified [11,12,15,16,17]. In the starred examples (Table 1)and the case of 3 CAI Pb-Pb ages [5], up to half the points were excluded solely because did not fit a pre-determined line. This approach is vulnerable to confirmation bias and produces fits with low MSWD and too-low Pb-Pb age uncertainty. Regressing the same data points as [10], were produce the Pb-Pb age of NWA 1670 of 4564.39±0.24 Myr. But selecting other combinations of data points, other, equally valid, isochrons yield ages from 4563.77±0.21 Myr to 4564.64±0.23 Myr. Similar arguments apply to the Pb-Pb isochrons built by [21] for chondrules 2-C1 (we find 4567.33±0.44 to 4567.85±0.46 Myr), 5-C2 (4566.84±0.53 to 4567.70±0.44 Myr), 3-C5 (4565.84±0.54to 4567.04±0.54)and 11-C1 (4565.36±0.51 to 4565.74±0.45 Myr). Our adopted ages for these and NWA 1670 are listed in Table 2.Table 2. tCAI estimated from various components, using our regressions for the chondrules & NWA 1670.SampleΔt26(Myr)tPb(Myr)t’CAI(Myr)D’Orbigny5.05±0.044563.43±0.194568.48±0.19SAH 995555.14±0.054563.88±0.274569.02±0.27NWA16704.64±0.104564.21±0.634568.85±0.67Asuka 8813943.81±0.044564.98±0.174568.79±0.17NWA 73255.33±0.054563.4±2.64568.7±2.6NWA 27965.06±0.044562.89±0.594567.95±0.59NWA 67045.29±0.134562.76±0.264568.05±0.292-C12.00±0.214567.59±0.704569.59±0.725-C22.07±0.224567.23±0.914569.30±0.933-C51.84±0.214566.44±1.124568.28±1.1411-C12.32±0.344565.52±0.664567.84±0.73achondrite4568.72±0.16chondrules4568.76±0.58combined4568.73±0.16A weighted average of the five NC achondrites(or just D’Orbigny, SAH 99555 and Asuka 881394)yields t*CAI= 4568.72 ± 0.16Myr. All are consistent with this value to within 1.8σ, and MSWD=1.5. Including the 4 U-corrected chondrules, t*CAI= 4568.73± 0.16Myrwith MSWD=1.66, which is statistically significant. All chondrules and NC achondrites are consistent with this to within 1.8σ, (Figure 1).Figure 1. Al-Mg formation times after t=0 vs. Pb-Pb ages. The five NC achondrites and four chondrules are consistent with a Pb-Pb age of t=0 of 4568.7 Myr. Discussion: The data from achondrites and chondrules are consistent with a single Pb-Pb age at t=0, justifying the assumption of 26Al homogeneity. The age, 4568.7 Myr, is ≈1.4 Myr older than the commonly accepted Pb-Pb age of CAIs that formed with canonical 26Al/27Al at t=0 [3]. Others have interpreted the discrepancy to signify 26Al heterogeneity in the CAI-forming region[5,21]. We suggest instead that CAIs were exposed to transient heating events that reset the Pb-Pb system without disturbing the Al-Mg system. Notably, chondrules typically experienced transient heating at these times in the nebula [22]. If so, direct measurements of CAIs will not yield as reliable a Pb-Pb age of t=0 as statistical approaches like this and that of [9].References:[1] Auer et al. 2009. [2] Jacobsen, B et al. 2008, EPSL 272, 353-364. [3] Tissot, Fet al. 2017, GCA 213, 593-617.[4] Villa, I et al. 2016, GCA 172, 387-392.[5] Amelin, Y et al. 2010, EPSL 300, 343-350.[6] Connelly, Jet al. 2012, Science 338, 651.[7] Bouvier, Aet al. 2011, LPICo 1639, 9054. [8] Bouvier, Aand Wadhwa, M2010, Nat Geosci 3, 637-641.[9] Nyquist, Let al. 2009, GCA 73, 5115-5136.[10] Schiller et al. 2015. [11] Wadhwa & Brennecka 2012. [12] Tissot et al. 2017. [13] Nyquist et al. 2003. [14] Wadhwa et al. 2009. [15] Wimpenny et al. 2019, GCA 244, 478-501.[16] Koefoed et al. 2016, GCA 183, 31-45. [17] Bouvier, A et al. 2011, GCA 75, 5310-5323. [18] Sanborn, Met al. 2019, GCA 245, 577-596. [19] Amelin, Yet al. 2019, GCA 245, 628-642.[20] Bollard, Jet al. 2017, Sci Adv 3 ,e1700407. [21] Bollard, Jet al. 2019, GCA 260, 62-83.[22] Villeneuve, J et al. 2009, Science 325, 985

S. J. Desch↗

Thermal and kinematic properties of ejecta in SN1987A revealed by XRISM

We present an analysis of high-resolution spectra from the shock-heated plasmas in SN 1987A, based on an observation using the Resolve instrument onboard the X-Ray Imaging and Spectroscopy Mission (XRISM). The 1.7–10 keV Resolve spectra are accurately represented by a single-component, plane-parallel shock plasma model, with a temperature of $2.84_{-0.08}^{+0.09}$ keV and an ionization parameter of $2.64_{-0.45}^{+0.58}$ × $10^{11}\,\,{\rm s\,\, cm}^{-3}$. The Resolve spectra are also well reproduced by the 3D magneto-hydrodynamic simulation presented by Orlando et al. (2020, A&A, 636, A22) suggesting substantial contribution from the ejecta. The metal abundances obtained with Resolve align with the Large Magellanic Cloud value, indicating that the X-rays in 2024 originate from “non-metal-rich” shock-heated ejecta and the reverse shock has not reached the inner metal-rich region of ejecta. Doppler widths of the atomic lines from Si, S, and Fe correspond to velocities of 1500–1700 km s$^{-1}$, where the thermal broadening effects in this non-metal-rich plasma are negligible. Therefore, the line broadening seen in Resolve spectra is determined by the large bulk motion of ejecta. For reference, we determined a $90\%$ upper limit on non-thermal emission from a pulsar wind nebula at $4.3 \times 10^{-13}$ erg cm$^{-2}$ s$^{-1}$ in the 2–10 keV range, aligning with NuSTAR findings by Greco et al. (2022, ApJ, 931, 132). Additionally, we searched for the $^{44}$Sc K line feature and found a $1\sigma$ upper limit of $1.0 \times 10^{-6}$ photons cm$^{-2}$ s$^{-1}$, which translates to an initial $^{44}$Ti mass of approximately $2 \times 10^{-4}\, M_{\odot }$, consistent with previous X-ray to soft gamma-ray observations (Boggs et al. 2015, Science, 348, 670; Grebenev et al. 2012, Nature, 490, 373; Leising 2006, ApJ, 651, 1019).

ISM: supernova remnants↗