Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Improvement of the thermal stability of sintered Nd-Fe-B magnets by intergranular addition of Dy{sub 82.3}Co{sub 17.7}

In this study, microstructure and magnetic properties of sintered Nd-Fe-B magnets with addition of Dy{sub 82.3}Co{sub 17.7} (wt. %) were investigated. By adding a small amount of Dy{sub 82.3}Co{sub 17.7}, the coercivity is improved greatly, and the irreversible loss is decreased sharply. The increase of Curie temperature suggests that Co atoms have entered into the 2:14:1 main phase. Microstructural analysis indicates that a well-developed core-shell structure was formed in the magnets with the addition of Dy{sub 82.3}Co{sub 17.7}. The improvement of magnetic properties can be attributed to the microstructural modification and the intrinsic properties' improvement.

36 MATERIALS SCIENCE↗

Achievement of high coercivity in sintered R-Fe-B magnets based on misch-metal by dual alloy method

The R-Fe-B (R, rare earth) sintered magnets prepared with different ratio of alloys of MM-Fe-B (MM, misch-metal) and Nd-Fe-B by dual alloy method were investigated. As expected, the high ratio of MM-Fe-B alloy degrades the hard magnetic properties heavily with intrinsic coercivity lower than 5 kOe. When the atomic ratio MM/R ≤ 21.5% the magnetic properties can reach a practical level of B{sub r} ≥ 12.1 kGs, H{sub cj} ≥ 10.7 kOe, and (BH){sub max} ≥ 34.0 MGOe. And the effect of H{sub cj} enhancement by the grain boundary diffusion process is obvious when MM/R ≤ 21.5%. It is revealed that the decrement of intrinsic magnetic properties of R{sub 2}Fe{sub 14}B matrix phase is not the main reason of the degradation of the magnets with high MM ratio. The change of deteriorated microstructure together with phase component plays fundamental roles in low H{sub cj}. In high MM ratio magnets, (a) after annealing, Ce atoms inside main phase are inclined to be segregated in the outer layer of the main phase grains; (b) there is no thin layer of Ce-rich phase as an analogue of Nd-rich phase to separate main phase grains; (c) excessive Ce tends to form CeFe{sub 2} grains.

36 MATERIALS SCIENCE↗

Magnetism in grain-boundary phase of a NdFeB sintered magnet studied by spin-polarized scanning electron microscopy

The magnetism in the grain-boundary phase of a NdFeB sintered magnet was measured by spin-polarized scanning electron microscopy (spin SEM). A sample magnet was fractured in the ultra-high-vacuum chamber to avoid oxidation, and its magnetizations in the exposed grain-boundary phase on the fracture surface were evaluated through the spin polarization of secondary electrons. Spin-SEM images were taken as the fracture surface was milled gradually by argon ions, and the magnetization in the grain-boundary phase was quantitatively obtained separately from that of the Nd{sub 2}Fe{sub 14}B phase. The obtained magnetization shows that the grain-boundary phase of this magnet has substantial magnetization, which was confirmed to be ferromagnetic.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermoelectric and transport properties of sintered n-type K{sub 8}Ba{sub 16}Ga{sub 40}Sn{sub 96} with type-II clathrate structure

This clathrate had a maximum dimensionless figure-of-merit, ZT, of 0.93 at 637 K, which was slightly higher than that of 0.83 for the sintered type-VIII clathrate Ba{sub 8}Ga{sub 16}Sn{sub 30}. We investigated the high-temperature thermoelectric properties, transport properties, electronic structures, and thermal stabilities of the clathrates. The type-II clathrate was found to be superior to the type-VIII clathrate as a thermoelectric material; it had a high thermal stability and melting point, 859 K, high mobility, 141 cm{sup 2}V{sup −1}s{sup −1} at 300 K, because of its low inertial mass, and low high-temperature lattice thermal conductivity, approximately 4 mW cm{sup −1}K{sup −1}, resulting from a larger unit cell and weaker bipolar thermal conduction. We discuss these properties in terms of the electronic structure and the differences between the two types of clathrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of thermal demagnetization behavior of Nd–Fe–B sintered magnets using magnetic domain observation

We used magnetic domain observation to statistically observe the thermal demagnetization behavior of Nd–Fe–B sintered magnets at elevated temperatures up to 150 °C. Simultaneous magnetization reversal in a hundred adjacent grains occurred at 90 °C because of the magnetic interaction among the grains beyond grain boundaries in the Dysprosium (Dy)-free low-coercivity magnet. Conversely, simultaneous magnetization reversal in a hundred grains did not occur in the Dy-added high-coercivity magnets, and the demagnetizing ratio steadily increased with temperature. Furthermore, the addition of Dy induced high thermal stability by eliminating the simultaneous thermal demagnetization, which was caused by the magnetic interaction among the grains.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

MgAl{sub 2}O{sub 4}(001) based magnetic tunnel junctions made by direct sputtering of a sintered spinel target

We developed a fabrication process of an epitaxial MgAl{sub 2}O{sub 4} barrier for magnetic tunnel junctions (MTJs) using a direct sputtering method from an MgAl{sub 2}O{sub 4} spinel sintered target. Annealing the sputter-deposited MgAl{sub 2}O{sub 4} layer sandwiched between Fe electrodes led to the formation of a (001)-oriented cation-disorder spinel with atomically sharp interfaces and lattice-matching with the Fe electrodes. A large tunnel magnetoresistance ratio up to 245% at 297 K (436% at 3 K) was achieved in the Fe/MgAl{sub 2}O{sub 4}/Fe(001) MTJ as well as an excellent bias voltage dependence. These results indicate that the direct sputtering is an alternative method for the realization of high performance MTJs with a spinel-based tunnel barrier.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Growth, sintering, and chemical states of Co supported on reducible CeO 2 (111) thin films: The effects of the metal coverage and the nature of the support

The growth, sintering, and interaction of cobalt with ceria were studied under ultrahigh vacuum conditions by vapor-deposition of Co onto well-defined CeOx(111) (1.5 < x < 2) thin films grown on Ru(0001). Charge transfer from Co to ceria occurs upon deposition of Co on CeO 1.96 and partially reduced CeO 1.83 at 300 K. X-ray photoelectron spectroscopy studies show that Co is oxidized to Co 2+ species at the cost of the reduction of Ce 4+ to Ce 3+ , at a lesser extent on reduced ceria. Co 2+ is the predominant species on CeO 1.96 at low Co coverages (e.g., ≤0.20 ML). The ratio of metallic Co/Co 2+ increases with the increase in the Co coverage. However, both metallic Co and Co 2+ species are present on CeO 1.83 even at low Co coverages with metallic Co as the major species. Scanning tunneling microscopy results demonstrate that Co tends to wet the CeO 1.96 surface at very low Co coverages at room temperature forming one-atomic layer high structures of Co–O–Ce. The increase in the Co coverage can cause the particle growth into three-dimensional structures. The formation of slightly flatter Co particles was observed on reduced CeO 1.83 . In comparison with other transition metals including Ni, Rh, Pt, and Au, our studies demonstrate that Co on ceria exhibits a smaller particle size and higher thermal stability, likely arising from strong metal–support interactions. The formed particles upon Co deposition at 300 K are present on the ceria surface after heating to 1000 K. The Co–ceria interface can be tuned by varying the Co metal coverage, the annealing temperature, and the nature of the ceria surface.

36 MATERIALS SCIENCE↗

In situ X-ray diffraction of pyrolite to 40 GPa using Kawai-type apparatus with sintered diamond anvils: possibility for the existence of iron-rich metallic particles in the lower mantle

We investigated phase relations in pyrolite at -33--40 GPa and -1800--2150 K by in situ X-ray diffraction using Kawai-type apparatus with sintered diamond anvils. The results demonstrated that MgSiO{sub 3}-rich orthorhombic perovskite (mpv), CaSiO{sub 3}-rich cubic perovskite (cpv) and (Mg,Fe)O ferropericlase (fp) are the stable phases in pyrolite bulk composition at the conditions corresponding to the lower mantle. However, chemical analyses of a run product recovered from -34 GPa by an analytical transmission electron microscope showed the coexistence of metallic iron particles with mpv, fp, and SiO{sub 2}-rich amorphous phase. Also, Fe/Mg partitioning coefficient between mpv and fp was found to be 0.66(31), which is consistent with previous results for pyrolite bulk composition at 26--30 GPa and -1900 K. These results indicate that iron-rich metallic particles can exist in the lower mantle as a stable phase to the depth of at least -900 km.

58 GEOSCIENCES↗

Quantification of deformation microstructure at ultra-low tensile strain in pure Al prepared by spark plasma sintering

A sample of Al with grain size of 5.1 mu m, prepared by spark plasma sintering, was deformed to a nominal strain of 0.35% under exposure to X-ray synchrotron radiation, allowing spatially resolved orientation measurements to be made during loading by use of a micro-diffraction technique. A significant heterogeneity in the deformation pattern between grains was observed. A statistical analysis shows that grain deformation depends more on crystallographic orientation than on grain size, with grains with tensile axis lying towards the < 001>-< 101> border of the unit triangle tending to undergo larger deformation. Other possible reasons for the different deformation behaviour between individual grains are briefly discussed.

Zhang, C L↗

Tuning the spontaneous exchange bias effect in La 1.5 Sr 0.5 CoMnO 6 with sintering temperature

Here, in this study, we present a study of the influence of microstructure on the magnetic properties of polycrystalline samples of the La 1.5 Sr 0.5 CoMnO 6 double perovskite, with primary attention to the spontaneous exchange bias effect, a fascinating recently discovered phenomena for which some materials exhibit unidirectional magnetic anisotropy after being cooled in zero magnetic fields. By sintering La 1.5 Sr 0.5 CoMnO 6 at different temperatures, we obtained samples with distinct average grain sizes, ranging from 1.54-6.65 μm. A detailed investigation of the material's structural, morphologic, electronic, and magnetic properties using x-ray powder diffraction, powder neutron diffraction, x-ray absorption near edge structure spectroscopy, scanning electron microscopy, and ac and dc magnetometry has revealed a systematic enhancement of the exchange bias effect with increasing the average grain size. This evolution is discussed in terms of changes in the material's porosity and grain morphology and its influence on the exchange couplings at the magnetic interfaces.

14 SOLAR ENERGY↗

Experimental Investigation of Electric Contact Resistance in Spark Plasma Sintering Tooling Setup

An experimental investigation on electric contact resistance in the tooling utilized in spark plasma sintering (SPS) is conducted. Two different SPS regimes are operated without the presence of processed powder to obtain the punch–punch (horizontal) and punch–die (vertical) contact resistance assessments separately. The processing temperature and applied pressure are considered to be the main factors that affect the contact resistance. These effects are analyzed by performing experiments at a maximum temperature of 1600°C with constant heating rate of 100°C/min. The applied pressure is ranging from 20 to 60 MPa and a 1 min holding time‐step is used to ensure stable measurements. It is shown that the contact resistance goes down as the temperature ramps up. An increase in the pressure leads to a decrease in the contact resistance. The mechanisms that cause these variations in the contact resistance are discussed. The dependence of assessed contact resistance of the utilized SPS system on the processing temperature and applied pressure is analytically described based on the regression analysis of the collected experimental data. A finite‐element simulation based on the obtained experimental results evidences that the electric contact resistance dominates the temperature evolution. The obtained results are of significant importance for modeling and optimization of SPS processes.

Wei, Xialu↗

In‐situ measurements of lattice expansion related to defect generation during flash sintering

Abstract We report results from in‐situ measurements of lattice expansion during flash sintering of 3 mol% yttria stabilized tetragonal zirconia taken at the Advanced Photon Source, Argonne National Laboratory. The expansion is anisotropic, with the relative expansion of the a ‐lattice constant exceeding that of the c ‐lattice constant. The anisotropic expansion cannot be explained by thermal expansion and is consistent with predictions from ab‐initio calculations based upon the generation of vacancy‐interstitial pairs of zirconium and oxygen.

Lebrun, J. ‐M.↗

Image quality improvement in megavoltage cone beam CT using an imaging beam line and a sintered pixelated array system

Purpose: To quantify the improvement in megavoltage cone beam computed tomography (MVCBCT) image quality enabled by the combination of a 4.2 MV imaging beam line (IBL) with a carbon electron target and a detector system equipped with a novel sintered pixelated array (SPA) of translucent Gd{sub 2}O{sub 2}S ceramic scintillator. Clinical MVCBCT images are traditionally acquired with the same 6 MV treatment beam line (TBL) that is used for cancer treatment, a standard amorphous Si (a-Si) flat panel imager, and the Kodak Lanex Fast-B (LFB) scintillator. The IBL produces a greater fluence of keV-range photons than the TBL, to which the detector response is more optimal, and the SPA is a more efficient scintillator than the LFB. Methods: A prototype IBL + SPA system was installed on a Siemens Oncor linear accelerator equipped with the MVision{sup TM} image guided radiation therapy (IGRT) system. A SPA strip consisting of four neighboring tiles and measuring 40 cm by 10.96 cm in the crossplane and inplane directions, respectively, was installed in the flat panel imager. Head- and pelvis-sized phantom images were acquired at doses ranging from 3 to 60 cGy with three MVCBCT configurations: TBL + LFB, IBL + LFB, and IBL + SPA. Phantom image quality at each dose was quantified using the contrast-to-noise ratio (CNR) and modulation transfer function (MTF) metrics. Head and neck, thoracic, and pelvic (prostate) cancer patients were imaged with the three imaging system configurations at multiple doses ranging from 3 to 15 cGy. The systems were assessed qualitatively from the patient image data. Results: For head and neck and pelvis-sized phantom images, imaging doses of 3 cGy or greater, and relative electron densities of 1.09 and 1.48, the CNR average improvement factors for imaging system change of TBL + LFB to IBL + LFB, IBL + LFB to IBL + SPA, and TBL + LFB to IBL + SPA were 1.63 (p < 10{sup -8}), 1.64 (p < 10{sup -13}), 2.66 (p < 10{sup -9}), respectively. For all imaging doses, soft tissue contrast was more easily differentiated on IBL + SPA head and neck and pelvic images than TBL + LFB and IBL + LFB. IBL + SPA thoracic images were comparable to IBL + LFB images, but less noisy than TBL + LFB images at all imaging doses considered. The mean MTFs over all imaging doses were comparable, at within 3%, for all imaging system configurations for both the head- and pelvis-sized phantoms. Conclusions: Since CNR scales with the square root of imaging dose, changing from TBL + LFB to IBL + LFB and IBL + LFB to IBL + SPA reduces the imaging dose required to obtain a given CNR by factors of 0.38 and 0.37, respectively. MTFs were comparable between imaging system configurations. IBL + SPA patient image quality was always better than that of the TBL + LFB system and as good as or better than that of the IBL + LFB system, for a given dose.

61 RADIATION PROTECTION AND DOSIMETRY↗

Highly-Conductive and Durable SOFC Cathode-Side Contact Based on Reactively-Sintered Mn-Co Spinel

A cathode-side contact layer with well-matched coefficient of thermal expansion is needed to prevent cracking of solid oxide fuel cell stacks from thermal cycling during stack operations. An Mn 1.25 Co 1.75 O 4 (MCO) spinel layer synthesized via reactive sintering with a metal-containing precursor was proposed as a highly conductive and durable contact material. Compared to the interconnect/contact/cathode assemblies with the (La 0.80 Sr 0.20 ) 0.95 MnO 3-x and La(Mn 0.45 Co 0.35 Cu 0.2 )O 3 contacts, the assembly with the MCO contact exhibited the lowest area-specific resistance at 800 °C (8.2 mΩ·cm 2 ) during 2000-h cyclic exposure and was crack-free based on the cross-sectional examination, indicative of the superiority of the spinel contact over the perovskite counterparts.

Electrochemistry↗

Fabrication of Tungsten-Rhenium Cladding materials via Spark Plasma Sintering for Ultra High Temperature Reactor Applications

This research will develop an optimized, cost-effective method for producing high-purity tungsten-rhenium alloyed fuel clad forms that are crucial for the development of a very high-temperature nuclear reactor. The study will provide critical insight into the fundamental behavior (processing-microstructure- property correlations) of W-Re alloys made using this new fabrication process comprising high-energy ball milling (HEBM) and spark plasma sintering (SPS). A broader goal is to re-establish the U.S. lead in the research field of refractory alloys, such as W-Re systems, with potential applications in very high-temperature nuclear reactors. An essential long-term goal for nuclear power is to develop the capability of operating nuclear reactors at temperatures in excess of 1,000K. This capability has applications in space exploration and some special terrestrial uses where high temperatures are needed in certain chemical or reforming processes. Refractory alloys have been identified as being capable of withstanding temperatures in excess of 1,000K and are considered critical for the development of ultra hightemperature reactors. Tungsten alloys are known to possess extraordinary properties, such as excellent high-temperature capability, including the ability to resist leakage of fissile materials when used as a fuel clad. However, there are difficulties with the development of refractory alloys: 1) lack of basic experimental data on thermodynamics and mechanical and physical properties, and 2) challenges associated with processing these alloys.

36 MATERIALS SCIENCE↗

Spark Plasma Sintering of Ultracapacitors

A solid-state ultracapacitor module to replace standard electrochemical batteries would achieve major performance gains and mass/volume reduction. This report summarizes a project to evaluate an alternative sintering process to produce a solid-state ultracapacitor to overcome the limitations of both the electrochemical batteries presently in use on spacecraft and of currently available electrochemical ultracapacitors. It will provide a robust energy storage device with higher reliability, wider working temperature range, longer lifetime, and less weight and volume than electrochemical batteries. As modern electronics decrease in size, more efficient and robust remote power is needed. Current state-of-the-art rechargeable batteries cannot be rapidly charged, contain harmful chemicals, and suffer from early wear-out mechanisms. Solid-state ultracapacitors are recyclable energy storage devices that offer the promise of higher power and a greater number of charge/discharge cycles than current rechargeable batteries. In addition, the theoretical energy density when compared to current electrochemical batteries indicates that a significant weight savings is possible. This is a project to develop a very high density solid-state ultracapacitor with giant permittivity and acceptable dielectric loss to overcome the energy-density barrier such that it will be a suitable replacement for batteries.

25 ENERGY STORAGE↗

Selective Laser Sintering of PA2200: Effects of print parameters on density, accuracy, and surface roughness

Additive manufacturing needs a broader selection of materials for part production. In order for the Los Alamos National Laboratory (LANL) to investigate new materials for selective laser sintering (SLS), this paper reviews research on the effect of print parameters on part density, accuracy, and surface roughness of polyamide 12 (PA12, PA2200). The literature review serves to enhance the understanding of how changing the laser powder, scan speed, etc. will affect the mechanical properties of a commercial powder. By doing so, this understanding will help the investigation of new materials for SLS.

36 MATERIALS SCIENCE↗

Developing Characterization Procedures for Qualifying both Novel Selective Laser Sintering Polymer Powders and Recycled Powders

Selective laser sintering (SLS) is an additive technique which is showing great promise over conventional manufacturing techniques. SLS requires certain key material properties for a polymer powder to be successfully processed into an end-use part, and therefore limited selection of materials are available. Furthermore, there has been evidence of a powder’s quality deteriorating following each SLS processing cycle. The current investigation serves to build a path forward in identifying new SLS powder materials by developing characterization procedures for identifying key material properties as well as for detecting changes in a powder’s quality. Thermogravimetric analyses, differential scanning calorimetry, and bulk density measurements were investigated.

36 MATERIALS SCIENCE↗