Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

The effects of copper and titanium on silicon solar cells

Copper-doped N/P silicon solar cells fabricated from the Czochralski grown single-crystal wafers were found to have good electrical characteristics, but the titanium-doped N/P silicon solar cells has considerably lower conversion efficiency. However, in the copper/titanium-doped solar cells, copper seems to mitigate the unfavorable effects of titanium. To explain this behavior, microstructural tests were performed on silicon wafers and solar cells doped with copper, titanium and copper/titanium. Dark forward and reverse I-V measurements were performed on the solar cells to correlate the microstructural defects with the p-n junction properties. It was found that copper precipitates were formed in the copper-doped and copper/titanium-doped wafers and cells. There was a significant voltage drop in the dark reverse I-V measurements of the titanium solar cells. Also, there were some electronically active defects in the depletion region of some titanium-doped cells. Reasons that lead to the above results are given in detail.

Salama, A. M.↗

Development of N/P AlGaAs free-standing top solar cells for tandem applications

The combination of a free standing AlGaAs top solar cell and an existing bottom solar cell is the highest performance, lowest risk approach to implementing the tandem cell concept. The solar cell consists of an AlGaAs substrate layer, an AlGaAs base layer, an AlGaAs emitter, and an ultra-thin AlGaAs window layer. The window layer is compositionally graded which minimizes reflection at the window layer/emitter interface and creates a built-in electric field to improve quantum response in the blue region of the spectrum. Liquid phase epitaxy (LPE) is the only viable method to produce this free standing top solar cell. Small (0.125 sq cm), transparent p/n AlGaAs top solar cells were demonstrated with optimum bandgap for combination with a silicon bottom solar cell. The efficiency of an AlGaAs/Si stack using the free standing AlGaAs device upon an existing silicon bottom solar cell is 24 pct. (1X, Air Mass Zero (AM0). The n/p AlGaAs top solar cell is being developed in order to facilitate the wiring configuration. The two terminal tandem stack will retain fit, form, and function of existing silicon solar cells. Progress in the development of large area (8 and 16 sq cm), free standing AlGaAs top solar cells is discussed.

Negley, Gerald H.↗

Recovery of shallow junction GaAs solar cells damaged by electron irradiation

Solar cells operated in space are subject to degradation from electron and proton radiation damage. It has been found that for deep junction p-GaAlAs/p-GaAs solar cells some of the electron radiation damage is removed by annealing the cells at 200 C. The reported investigation shows that shallow junction p-GaAlAs/p-GaAs/n-GaAs heteroface solar cells irradiated with 1 MeV electrons show a more complete recovery of short-circuit current than do the deep junction cells. The heteroface p-GaAlAs/p-GaAs/n-GaAs solar cells studied were fabricated using the etch-back epitaxy process.

Walker, G. H.↗

Terrestrial applications of FEP-encapsulated solar cell modules

FEP-encapsulated solar cell modules and arrays have been designed and built expressly for terrestrial applications. System design including solar cell array mechanical design and the approach to system sizing is outlined. Such solar cell systems have been installed at six sites. Individual modules have undergone marine environment tests. Results from seven months of operation indicate that system is meeting its electrical design requirements. No mechanical degradation has been reported. The array on Mammoth Mountain, California has been damaged by rime ice but shows no loss in electrical output. Marine environment tests on single modules have shown that elements of the module must be completely sealed by the FEP. Based on the limited test data available, the FEP-encapsulated solar cell module appears well suited to terrestrial applications.

Forestieri, A. F.↗

Terrestrial applications of FEP-encapsulated solar cell modules

FEP-encapsulated solar cell modules and arrays have been designed and built expressly for terrestrial applications. System design including solar cell array mechanical design and the approach to system sizing is outlined. Such solar cell systems have been installed at six sites. Individual modules have undergone marine environment tests. Results from seven months of operation indicate that the system is meeting its electrical design requirements. No mechanical degradation has been reported. An array on Mammoth Mountain, California has been damaged by rime ice but shows no loss in electrical output. Marine environment tests on single modules have shown that elements of the module must be completely sealed by the FEP. Based on the limited test data available, the FEP-encapsulated solar cell module appears well suited to terrestrial applications.

Forestieri, A. F.↗

Study of Effects of Cl and Se in CdSeTe Solar Cells Using Scanning Transmission Electron Microscopy

Solar cells based on poly-crystalline CdTe thin films are a leading candidate for low-cost conversion of solar energy due to their near optimum band gap, high absorption coefficient and ease of manufacturing. Due to non-radiative Shockley-Read-Hall (SRH) recombination at grain boundaries (GBs), dislocations, and point defects, current CdTe-based solar cell efficiency appears to be limited to ~22%, which is still below the theoretical limit (~30%). It is well known that CdCl 2 annealing is essential for high performing CdTe solar cells due to grain recrystallization and passivation of defect states within the band gap by Cl atoms. Incorporating Se into CdTe to form an alloyed CdSeTe solar cells also shows a high overall efficiency. Simultaneous addition of Cl and Se can further improve the efficiencies of CdTe solar cells, but yet a comprehensive experimental and theoretical study of effects of Cl and Se in CdSeTe solar cell is absent.

14 SOLAR ENERGY↗

Preliminary Low Temperature Electron Irradiation of Triple Junction Solar Cells

For many years extending solar power missions far from the sun has been a challenge not only due to the rapid falloff in solar intensity (intensity varies as inverse square of solar distance) but also because some of the solar cells in an array may exhibit a LILT (low intensity low temperature) degradation that reduces array performance. Recent LILT tests performed on commercial triple junction solar cells have shown that high performance can be obtained at solar distances as great as approx. 5 AU1. As a result, their use for missions going far from the sun has become very attractive. One additional question that remains is whether the radiation damage experienced by solar cells under low temperature conditions will be more severe than when measured during room temperature radiation tests where thermal annealing may take place. This is especially pertinent to missions such as the New Frontiers mission Juno, which will experience cell irradiation from the trapped electron environment at Jupiter. Recent testing2 has shown that low temperature proton irradiation (10 MeV) produces cell degradation results similar to room temperature irradiations and that thermal annealing does not play a factor. Although it is suggestive to propose the same would be observed for low temperature electron irradiations, this has not been verified. JPL has routinely performed radiation testing on commercial solar cells and has also performed LILT testing to characterize cell performance under far sun operating conditions. This research activity was intended to combine the features of both capabilities to investigate the possibility of any room temperature annealing that might influence the measured radiation damage. Although it was not possible to maintain the test cells at a constant low temperature between irradiation and electrical measurements, it was possible to obtain measurements with the cell temperature kept well below room temperature. A fluence of 1E15 1MeV electrons was selected as representative of a moderately high dose that might be expected for a solar powered mission. Fluences much greater than this would require large increases in array area and mass, compromising the ability of PV to compete with non-solar alternatives.

Stella, Paul M.↗

Characterization of terrestrial solar cells for space applications: Electrical characteristics of thin Westinghouse dendritic web cells as a function of solar intensity, temperature, and incidence angle

Electrical characteristics of thin (100- and 140-micron) Westinghouse dendritic-web N/P silicon solar cells are presented in graphical and tabular format as a function of solar illumination intensity and temperature. Performance is also shown as a function of solar illlumination angle of incidence for AMO.

Stella, P. M.↗

A theoretical study of heterojunction and graded band gap type solar cells

The theory of heterojunction and graded bandgap solar cells was studied to help determine the material compositions and device dimensions needed for high efficiency solar cells. Because of the involved analysis of the fundamental equations describing solar cell operation, a general numerical device analysis program was used. A major part of the initial work was involved in modifying an existing silicon solar cell analysis program to account for the unique features of graded bandgap and heterojunction solar cells. The most successful III-V solar cells have so far been constructed in the GaAs and Gal-xAlxAs material systems; this project was concerned with such solar cells. The most efficient solar cell so far evaluated is an abrupt heterojunction cell with a pure AlAs layer at the surface with a GaAs substrate. The predicted efficiency for this cell is slightly larger than that of a graded bandgap Gal-xAlxAs solar cell.

Hauser, J. R.↗

High throughput solar cell ablation system

A solar cell is formed using a solar cell ablation system. The ablation system includes a single laser source and several laser scanners. The laser scanners include a master laser scanner, with the rest of the laser scanners being slaved to the master laser scanner. A laser beam from the laser source is split into several laser beams, with the laser beams being scanned onto corresponding wafers using the laser scanners in accordance with one or more patterns. The laser beams may be scanned on the wafers using the same or different power levels of the laser source.

14 SOLAR ENERGY↗

High throughput solar cell ablation system

A solar cell is formed using a solar cell ablation system. The ablation system includes a single laser source and several laser scanners. The laser scanners include a master laser scanner, with the rest of the laser scanners being slaved to the master laser scanner. A laser beam from the laser source is split into several laser beams, with the laser beams being scanned onto corresponding wafers using the laser scanners in accordance with one or more patterns. The laser beams may be scanned on the wafers using the same or different power levels of the laser source.

14 SOLAR ENERGY↗