Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Mesoporous Fe-doped MgO nanoparticles as a heterogeneous photo-Fenton-like catalyst for degradation of salicylic acid in wastewater

Mesoporous Fe-doped MgO nanoparticles were synthesized using a facile sol-gel method and utilized for photo-Fenton-like degradation of salicylic acid (SA). The MgO surface dissolution facilitated an increase in the pH under the reaction conditions that allowed the Fe-MgO catalyst to be active without detectable iron leaching. Under simulated solar radiation, SA was completely degraded with an initial rate constant of 0.048 min -1 at the optimal reaction conditions of 500 ppm loading of 5% Fe-MgO, 20 mM H 2 O 2 concentration, and 50 ppm SA concentration. The catalyst was stable over 5 reaction cycles. The Fe-MgO catalyst was shown to have a surface area up to 171 m 2 /g and contain hematite (Fe 2 O 3 ) nanoparticles with octahedrally coordinated iron catalytic centers, as inferred from diffuse reflectance UV–vis measurements. Post-reaction catalyst characterization showed that some Fe 2+ was present in the catalyst due to the redox cycle during the chain initiation and propagation steps of the reaction.

36 MATERIALS SCIENCE↗

Formulation, Implementation and Validation of a Two-Fluid model in a Fuel Cell CFD Code

Water management is one of the main challenges in PEM Fuel Cells. While water is essential for membrane electrical conductivity, excess liquid water leads to flooding of catalyst layers. Despite the fact that accurate prediction of two-phase transport is key for optimal water management, understanding of the two-phase transport in fuel cells is relatively poor. Wang et. al. have studied the two-phase transport in the channel and diffusion layer separately using a multiphase mixture model. The model fails to accurately predict saturation values for high humidity inlet streams. Nguyen et. al. developed a two-dimensional, two-phase, isothermal, isobaric, steady state model of the catalyst and gas diffusion layers. The model neglects any liquid in the channel. Djilali et. al. developed a three-dimensional two-phase multicomponent model. The model is an improvement over previous models, but neglects drag between the liquid and the gas phases in the channel. In this work, we present a comprehensive two-fluid model relevant to fuel cells. Models for two-phase transport through Channel, Gas Diffusion Layer (GDL) and Channel-GDL interface, are discussed. In the channel, the gas and liquid pressures are assumed to be same. The surface tension effects in the channel are incorporated using the continuum surface force (CSF) model. The force at the surface is expressed as a volumetric body force and added as a source to the momentum equation. In the GDL, the gas and liquid are assumed to be at different pressures. The difference in the pressures (capillary pressure) is calculated using an empirical correlations. At the Channel-GDL interface, the wall adhesion affects need to be taken into account. SIMPLE-type methods recast the continuity equation into a pressure-correction equation, the solution of which then provides corrections for velocities and pressures. However, in the two-fluid model, the presence of two phasic continuity equations gives more freedom and more complications. A general approach would be to form a mixture continuity equation by linearly combining the phasic continuity equations using appropriate weighting factors. Analogous to mixture equation for pressure correction, a difference equation is used for the volume/phase fraction by taking the difference between the phasic continuity equations. The relative advantages of the above mentioned algorithmic variants for computing pressure correction and volume fractions are discussed and quantitatively assessed. Preliminary model validation is done for each component of the fuel cell. The two-phase transport in the channel is validated using empirical correlations. Transport in the GDL is validated against results obtained from LBM and VOF simulation techniques. The Channel-GDL interface transport will be validated against experiment and empirical correlation of droplet detachment at the interface.

30 DIRECT ENERGY CONVERSION↗

Perovskite-Type Solid Solution Nano-Electrocatalysts Enable Simultaneously Enhanced Activity and Stability for Oxygen Evolution

A trade-off between catalytic activity and structural stability generally exists in oxygen evolution electrocatalysis, especially in acidic environment. This dilemma limits the development of higher-performance electrocatalysts that are required by next-generation electrochemical technologies. In this work it is demonstrated that the inverse catalytic activity–structural stability relation can be broken by alloying catalytically inert strontium zirconate with the other catalytically active perovskite, strontium iridate. This strategy results in an alloyed perovskite electrocatalyst with simultaneously improved iridium mass activity and structural stability, by about five times, for the oxygen evolution reaction under acidic conditions. The experimental and theoretical results suggest that the alloying strategy generates multiple positive effects, mainly including the reduction of catalyst size, the decrease of catalyst covalency, and the weakening of surface oxygen-binding ability. The synergistic optimization of bulk and surface properties, as a result, enhances the intrinsic activity and availability of surface iridium sites, whilst significantly inhibiting the surface cation corrosion during electrocatalysis.

36 MATERIALS SCIENCE↗

Characterization of Porous Transport Layers Towards the Development of Efficient Proton Exchange Membrane Water Electrolysis

The current goals for implementing the hydrogen economy have highlighted a need to further optimize water-splitting technologies for clean hydrogen production. Proton exchange membrane water electrolysis (PEMWE) is a leading technology, but further optimizations of anode materials including the porous transport layer (PTL) and the adjacent catalyst layer (CL) are required to increase overall cell performance and reduce cost. This literature review describes advances in PTL development and characterization, highlighting early PTL characterization work and most common methods including capillary flow porometry and mercury intrusion porometry, optical imaging, neutron and x-ray radiography, and x-ray computed tomography. The article also discusses PTL protective coatings and their characterizations, focusing on platinum group metal (PGM)-based coatings, alternative non-PGM-based coatings, post-treated PTLs, and investigations into thin PGM-based coatings. Furthermore, it highlights the integration of the PTL and the adjacent CL along with associated characterization challenges. Lastly, this review discusses future developments in the characterization needed to improve PEMWE's performance and long-term durability are discussed.

08 HYDROGEN↗

Self‐Consistent Convolutional Density Functional Approximations: Application to Adsorption at Metal Surfaces

The exchange-correlation (XC) functional in density functional theory is used to approximate multi-electron interactions. A plethora of different functionals are available, but nearly all are based on the hierarchy of inputs commonly referred to as “Jacob's ladder.” This paper introduces an approach to construct XC functionals with inputs from convolutions of arbitrary kernels with the electron density, providing a route to move beyond Jacob's ladder. We derive the variational derivative of these functionals, showing consistency with the generalized gradient approximation (GGA), and provide equations for variational derivatives based on multipole features from convolutional kernels. A proof-of-concept functional, PBEq, which generalizes the PBEα framework with mathematical equation being a spatially-resolved function of the monopole of the electron density, is presented and implemented. It allows a single functional to use different GGAs at different spatial points in a system, while obeying PBE constraints. Analysis of the results underlines the importance of error cancellation and the XC potential in data-driven functional design. After testing on small molecules, bulk metals, and surface catalysts, the results indicate that this approach is a promising route to simultaneously optimize multiple properties of interest.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Intensified biogas to liquid (IBGTL) Process: Experimental validation and modeling analysis

The Intensified Biogas to Liquid (IBGTL) process aims to overcome traditional economy-of-scale barriers in biogas-to-liquid fuel production by integrating bi-reforming and Fischer-Tropsch synthesis (FTS) in a single IBGTL reactor. This reactor operates at uniform pressure with different optimized temperatures across two zones for efficient conversion, utilizing multifunctional bi-reforming catalysts and high-temperature FTS catalysts. Bench scale experiments were carried out using landfill gas (LFG) in a single pass process, and the yield data from these experiments were fed into process scale-up design and techno-economic analysis (TEA) across four scenarios: (1) a single pass process, (2) a process with material recycling, (3) a process with liquefied petroleum gas (LPG) co-product recovery, and (4) a process with electricity generation from the fuel gas produced. TEA identified Scenario 2 as the most cost-effective, achieving a Minimum Fuel Selling Price (MFSP) of $\$4.59$ per gallon, competitive with the current national diesel price of $\$4.7$ per gallon. However, comparison with the conventional two-reactor system highlights the need for catalyst performance improvements. Sensitivity analysis emphasized the importance of manufacturing cost, liquid fuel yield, and biogas flow rate. Further analysis determined that the IBGTL process must achieve a diesel mass yield beyond 11.7% to surpass the economic viability of the conventional TriFTS (Tri-reforming followed by Fischer-Tropsch Synthesis) process. If the IBGTL process attains the TriFTS yield of up to 17%, the resulting MFSP could be approximately 31% lower than the current TriFTS MFSP. Furthermore, renewable energy credits and carbon credits can further enhance the economic viability of BGTL processes.

09 BIOMASS FUELS↗

In Situ Strain Evolution on Pt Nanoparticles during Hydrogen Peroxide Decomposition

Fundamental understanding of structural changes during catalytic reactions is crucial to understanding the underlying mechanisms and optimizing efficiencies. Surface energy and related catalytic mechanisms are widely studied. However, the catalyst lattice deformation induced by catalytic processes is not well understood. Here, we study the strain in an individual platinum (Pt) nanoparticle (NP) using Bragg coherent diffraction imaging under in situ oxidation and reduction reactions. When Pt NPs are exposed to H 2 O 2 , a typical oxidizer and an intermediate during the oxygen reduction reaction process, alternating overall strain distribution near the surface and inside the NP is observed at the (111) Bragg reflection. In contrast, relatively insignificant changes appear in the (200) reflection. Density functional theory calculations are employed to rationalize the anisotropic lattice strain in terms of induced stress by H 2 O 2 adsorption and decomposition on the Pt NP surface. Our study provides deeper insight into the activity-structure relationship in this system.

3D imaging↗

Design and Synthesis of Highly-Dispersed WO 3 Catalyst with Highly Effective NH 3 –SCR Activity for NO x Abatement

The development of high-efficiency catalysts, especially for selective catalytic reduction of NO x with NH 3 (NH 3 –SCR) catalysts, with outstanding low-temperature catalytic reactivity and impressive lifetime remains a great challenge in the field of eliminating vehicle engine exhausts. In this work, we present a novel gas-bubbling-assisted dispersed hybrid nanocrystal-assisted hydrothermal deposition (GBD-HNHD) strategy to fabricate a W@CeZrAlO x catalyst with highly dispersed WO 3 nanocrystals (10 wt %) (W@CZA-HNHD). Compared with the W/CeZrAlO x catalyst prepared with the impregnation method (W@CZA-IM), W@CZA-HNHD not only exhibits highly effective low-temperature deNO x activity (the light-off temperature being lowered 45 °C) but also shows an exceptional stability (100 h time-on-stream testing with seven measurement cycles) and long lifetime (compares well with 135,000 miles). This work not only provides a new route to prepare an advanced catalyst with high loading isolated active sites but also lays a foundation for optimizing the utilization efficiency of the catalytically active species in the practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Illuminating the mechanistic impacts of an Fe-quaterpyridine functionalized crystalline poly(triazine imide) semiconductor for photocatalytic CO 2 reduction

The strategy of incorporating earth-abundant catalytic centers into light-absorbing architectures is desirable from the viewpoint of low cost, low toxicity, and versatility for activating small molecules to produce solar-based fuels. Herein, we show that an Fe-quaterpyridine molecular catalyst can be anchored to a light-absorbing, crystalline, carbon nitride (PTI), to yield a molecular-catalyst/material hybrid, Fe-qpy-PTI, capable of facilitating CO 2 reduction to CO selectively (up to ∼97–98%) in aqueous solution under low-intensity light irradiation. This hybrid material leverages the ability of the Fe-qpy catalyst to bind CO 2 upon a one-electron reduction, as achieved by transfer of excited electrons from the carbon-nitride semiconductor. At a low incident power density of only 50 mW cm −2 , the catalytic activity of the hybrid material was measured across a range of catalyst loadings from 0.1–3.8 wt%, yielding CO rates of up to 596 μmol g −1 h −1 for a 3.8 wt% loading during a 3 h experiment. Over the course of 8 h, the hybrid material attained a CO evolution rate of 608 μmol g −1 h −1 and 305 turnovers for a TOF of ∼38 h −1 and an apparent quantum yield of 2.6%. Higher light intensities provided an initial increase in activity but negatively impacted photocatalytic rates with time, with an AQY of 0.6% at 150 mW cm −2 and 0.4% at 250 mW cm −2 . Transient absorption spectroscopy results showed electron survival probabilities consistent with the trends in observed product rates. Computational modeling was also used to evaluate and understand the mechanistic pathway of the high product selectivity for CO versus H 2 . These results thus help unveil key factors for leveraging the mechanistic understanding of molecular catalysts for CO 2 reduction for pairing with light absorbing semiconductors and establishing optimal conditions to attain maximal rates in aqueous solution.

McGuigan, Scott [Baylor University, Waco, TX (Unit↗

BiVO{sub 4} photoanodes for water splitting with high injection efficiency, deposited by reactive magnetron co-sputtering

Photoactive bismuth vanadate (BiVO{sub 4}) thin films were deposited by reactive co-magnetron sputtering from metallic Bi and V targets. The effects of the V-to-Bi ratio, molybdenum doping and post-annealing on the crystallographic and photoelectrochemical (PEC) properties of the BiVO{sub 4} films were investigated. Phase-pure monoclinic BiVO{sub 4} films, which are more photoactive than the tetragonal BiVO{sub 4} phase, were obtained under slightly vanadium-rich conditions. After annealing of the Mo-doped BiVO{sub 4} films, the photocurrent increased 2.6 times compared to undoped films. After optimization of the BiVO{sub 4} film thickness, the photocurrent densities (without a catalyst or a blocking layer or a hole scavenger) exceeded 1.2 mA/cm{sup 2} at a potential of 1.23 V{sub RHE} under solar AM1.5 irradiation. The surprisingly high injection efficiency of holes into the electrolyte is attributed to the highly porous film morphology. This co-magnetron sputtering preparation route for photoactive BiVO{sub 4} films opens new possibilities for the fabrication of large-scale devices for water splitting.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic sparse x-ray nanotomography reveals ionomer hydration mechanism in polymer electrolyte fuel-cell catalyst

Tomographic imaging of time-evolving samples is a challenging yet important task for various research fields. At the nanoscale, current approaches face limitations of measurement speed or resolution due to lengthy acquisitions. We developed a dynamic nanotomography technique based on sparse dynamic imaging and 4D tomography modeling. We demonstrated the technique, using ptychographic x-ray computed tomography as its imaging modality, on resolving the in situ hydration process of polymer electrolyte fuel cell (PEFC) catalyst. The technique provides a 40-time increase in temporal resolution compared to conventional approaches, yielding 28 nm half-period spatial and 12 min temporal resolution. The results allow a quantitative characterization of the water intake process inside PEFC catalysts with nanoscale resolution, which is crucial for understanding their electrochemical mechanisms and optimizing their performance. Our technique enables high-speed operando nanotomography studies and paves the way for wider application of dynamic tomography at the nanoscale.

Science & Technology - Other Topics↗

Final Report: Process Intensification of Hydrogen Production through Sorption-Enhanced Gasification of Biomass

The University of Utah, in partnership with Idaho National Laboratory (INL), evaluated Sorption-Enhanced Gasification (SEG) as a transformative pathway for producing hydrogen with the potential for negative CO 2 emissions. SEG integrates gasification, water-gas shift, and in-situ carbon capture within a dual fluidized bed reactor to enable efficient clean hydrogen production. Key challenges related to biomass variability and process complexity were addressed through feedstock engineering, reaction optimization, and process validation. A co-pelletized biomass–limestone feedstock was developed to simplify feeding and introduction of makeup limestone. Kinetic and sorbent studies identified optimal operating conditions and confirmed the suitability of low-cost limestone, while catalysts were developed to reduce tar formation. Reactor modeling and techno-economic analysis indicated that SEG can achieve competitive hydrogen production costs, particularly when combined with carbon incentives, supporting its potential for scale-up and carbon-negative operation.

08 HYDROGEN↗

Replacing Pyridine with Pyrazine in Molecular Cobalt Catalysts: Effects on Electrochemical Properties and Aqueous H2 Generation

Four new molecular Co(II)tetrapyridyl complexes were synthesized and evaluated for their activity as catalysts for proton reduction in aqueous environments. The pyridine groups around the macrocycle were substituted for either one or two pyrazine groups. Single crystal X-ray analysis shows that the pyrazine groups have minimal impact on the Co(II)–N bond lengths and molecular geometry in general. X-band EPR spectroscopy confirms the Co(II) oxidation state and the electronic environment of the Co(II) center are only very slightly perturbed by the substitution of pyrazine groups around the macrocycle. The substitution of pyrazine groups has a substantial impact on the observed metal- and ligand-centered reduction potentials as well as the overall H2 catalytic activity in a multimolecular system using the [Ru(2,2′-bipyridine)3]Cl2 photosensitizer and ascorbic acid as a sacrificial electron donor. The results reveal interesting trends between the H2 catalytic activity for each catalyst and the driving force for electron transfer between either the reduced photosensitizer to catalyst step or the catalyst to proton reduction step. The work presented here showcases how even the difference of a single atom in a molecular catalyst can have an important impact on activity and suggests a pathway to optimize the photocatalytic activity and stability of molecular systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Biorefinery and Hydrogen Fuel Cell Research (Final Technical Report)

In this project we focused on several aspects of technology development that advances the formation of an integrated biorefinery. These focus areas include: [1] establishment of pyrolysis processing systems and characterization of the product oils for fuel applications, including engine testing of a preferred product and its pro forma economic analysis; [2] extraction of sugars through a novel hotwater extaction process, and the development of levoglucosan (a pyrolysis BioOil intermediate); [3] identification and testing of the use of biochar, the coproduct from pyrolysis, for soil applications; [4] developments in methods of atomic layer epitaxy (for efficient development of coatings as in fuel cells); [5] advancement in fermentation of lignocellulosics, [6] development of algal biomass as a potential substrate for the biorefinery, and [7] development of catalysts from coproducts. These advancements are intended to provide a diverse set of product choices within the biorefinery, thus improving the cost effectiveness of the system. Technical effectiveness was demonstrated in the pyrolysis biooil based diesel fuel supplement, sugar extraction from lignocelluose, use of biochar, production of algal biomass in wastewaters, and the development of catalysts. Economic feasibility of algal biomass production systems seems attractive, relative to the other options. However, further optimization in all paths, and testing/demonstration at larger scales are required to fully understand the economic viabilities. The various coproducts provide a clear picture that multiple streams of value can be generated within an integrated biorefinery, and these include fuels and products.

09 BIOMASS FUELS↗

Solar Reforming of Carbon Dioxide to Produce Diesel Fuel

This project focused on the demonstration of an innovative technology, referred to as the Sunexus CO2 Solar Reformer, which utilizes waste CO2 as a feedstock for the efficient and economical production of synthetic diesel fuel using solar thermal energy as the primary energy input. The Sunexus technology employs a two stage process for the conversion of CO2 to diesel fuel. A solar reforming system, including a specially designed reactor and proprietary CO2 reforming catalyst, was developed and used to convert captured CO2 rich gas streams into syngas (primarily hydrogen and carbon monoxide) using concentrated solar energy at high conversion efficiencies. The second stage of the system (which has been demonstrated under other funding) involves the direct conversion of the syngas into synthetic diesel fuel using a proprietary catalyst (Terra) previously developed and validated by Pacific Renewable Fuels and Chemicals (PRFC). The overall system energy efficiency for conversion of CO2 to diesel fuel is 74%, due to the use of solar energy. The results herein describe modeling, design, construction, and testing of the Sunexus CO2 Solar Reformer. Extensive parametric testing of the solar reformer and candidate catalysts was conducted and chemical kinetic models were developed. Laboratory testing of the Solar Reformer was successfully completed using various gas mixtures, temperatures, and gas flow rates/space velocities to establish performance metrics which can be employed for the design of commercial plants. A variety of laboratory tests were conducted including dry reforming (CO2 and CH{sub 4}), combination dry/steam reforming (CO2, CH{sub 4} & H{sub 2}O), and tri-reforming (CO2, CH{sub 4}, H{sub 2}O & O{sub 2}). CH{sub 4} and CO2 conversions averaged 95-100% and 50-90% per reformer cycle, respectively, depending upon the temperatures and gas space velocities. No formation of carbon deposits (coking) on the catalyst was observed in any of these tests. A 16 ft. diameter, concentrating solar dish was modified to accommodate the Sunexus CO2 Solar Reformer and the integrated system was installed at the Pacific Renewable Fuels and Chemicals test site at McClellan, CA. Several test runs were conducted without catalyst during which the ceramic heat exchanger in the Sunexus Solar Reformer reached temperatures between 1,050 F (566 C) and 2,200 F (1,204 C) during the test period. A dry reforming mixture of CO2/CH{sub 4} (2.0/1.0 molar ratio) was chosen for all of the tests on the integrated solar dish/catalytic reformer during December 2010. Initial tests were carried out to determine heat transfer from the collimated solar beam to the catalytic reactor. The catalyst was operated successfully at a steady-state temperature of 1,125 F (607 C), which was sufficient to convert 35% of the 2/1 CO2/CH{sub 4} mixture to syngas. This conversion efficiency confirmed the results from laboratory testing of this catalyst which provided comparable syngas production efficiencies (40% at 1,200 F [650 C]) with a resulting syngas composition of 20% CO, 16% H{sub 2}, 39% CO2 and 25% CH{sub 4}. As based upon the laboratory results, it is predicted that 90% of the CO2 will be converted to syngas in the solar reformer at 1,440 F (782 C) resulting in a syngas composition of 50% CO: 43% H{sub 2}: 7% CO2: 0% CH{sub 4}. Laboratory tests show that the higher catalyst operating temperature of 1,440 F (782 C) for efficient conversion of CO2 can certainly be achieved by optimizing solar reactor heat transfer, which would result in the projected 90% CO2-to-syngas conversion efficiencies. Further testing will be carried out during 2011, through other funding support, to further optimize the solar dish CO2 reformer. Additional studies carried out in support of this project and described in this report include: (1) An Assessment of Potential Contaminants in Captured CO2 from Various Industrial Processes and Their Possible Effect on Sunexus CO2 Reforming Catalysts; (2) Recommended Measurement Methods for Assessing Contaminant Levels in Captured CO2 Streams; (3) An Assessment of Current Commercial Scale Fisher-Tropsch (F-T) Technologies for the Conversion of Syngas to Fuels; (4) An Overview of CO2 Capture Technologies from Various Industrial Sources; and (5) Lifecycle Analysis for the Capture and Conversion of CO2 to Synthetic Diesel Fuel. Commercial scale Sunexus CO2 Solar Reformer plant designs, proposed in this report, should be able to utilize waste CO2 from a wide variety of industrial sources to produce a directly usable synthetic diesel fuel that replaces petroleum derived fuel, thus improving the United States energy security while also sequestering CO2. Our material balance model shows that every 5.0 lbs of CO2 is transformed using solar energy into 6.26 lbs (1.0 U.S. gallon) of diesel fuel and into by-products, which includes water. Details are provided in the mass and energy model in this report.

03 NATURAL GAS↗

Supported Single Fe Atoms Prepared via Atomic Layer Deposition for Catalytic Reactions

In this work, we report a general strategy to synthesize Fe single-atom catalysts (SACs) on various substrates (e.g., multiwalled carbon nanotubes, SiO 2 , and TiO 2 ) with high Fe loading (>1.5 wt %) by atomic layer deposition (ALD) through optimization of ferrocene (Fe precursor) dose time. Fe/SiO 2 and Fe/TiO 2 SACs were used for CO oxidation reactions and catalytic degradation of a methylene blue (MB) solution, respectively. Compared with reported iron oxide catalysts, the efficiency of Fe/SiO 2 for CO oxidation was more than 2 orders of magnitude higher than the reported values. The photocatalysis experiment demonstrated that TiO 2 nanoparticles, deposited with two cycles of Fe ALD, showed the highest activity and had a more than 6-fold photocatalytic activity enhancement over pure TiO 2 for the degradation of MB. This universal method, optimized Fe ALD, expands the potential applications of Fe SACs on different substrates.

36 MATERIALS SCIENCE↗

Smart culture medium optimization for recombinant protein production: Experimental, modeling, and AI/ML-driven strategies

Recombinant protein production (RPP) is central to biotechnology, where recombinant proteins are used as either end products or catalysts in the synthesis of chemicals, fuels, and materials. Among the major cost drivers, culture medium plays a pivotal role in determining protein yield and quality. This review presents a comprehensive perspective on the critical stages of “smart” culture medium optimization: planning, screening, modeling, optimization, and validation. In the planning stage, we examine the nutritional and energetic roles of medium components, including carbon, nitrogen, amino acids, salts, and trace metals, and their impacts on culture parameters such as pH, oxidative state, and osmolality. We highlight the variability in trace metal content due to water sources, culture vessels, and raw materials, which can substantially influence RPP. The screening stage covers Design of Experiments (DoE) approaches, assessing their theoretical basis, implementation, and limitations. For modeling, we describe methods that integrate experimental data to develop predictive models for smart medium formulation. Model-based optimization strategies can then be employed to select optimal media compositions for a given application. The validation stage aims to evaluate model predictions and provide feedback for model training and refinement. Finally, we survey mechanistic and artificial intelligence/machine learning (AI/ML)-driven models as integrated, transformational tools for predictive modeling of bioprocess conditions, nutrient availability, cellular metabolism, and protein quality, with the goal of optimizing culture media to enhance protein yields while reducing costs and environmental impact. We conclude by addressing the challenges of translating laboratory-scale medium optimization to industrial-scale settings and exploring future AI/ML-driven approaches that may overcome current bottlenecks and accelerate medium design for RPP. Overall, this review provides a unified framework for advancing smart medium design in RPP.

Artificial Intelligence/Machine Learning (AI/ML)↗