Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Fabrication, microstructure and mechanical properties of W-NiTi composites

Here, new two-phase tungsten-based composites containing 88 wt% tungsten powders and 12 wt% nearly equiatomic NiTi alloy deforming by martensite variant detwinning were fabricated by infiltration and hot pressing in this study. The change of Ti/Ni ratio in NiTi mater alloy and the effect of addition of Nb element on the microstructure, martensitic transformation and mechanical properties of W-NiTi composites were investigated by comparison of W-Ni 50 Ti 50 , W-Ni 44 Ti 56 , W-Ni 42 Ti 58 and W-Ni 42 Ti 53 Nb 5 composites. The results showed that brittle Ni 3 Ti formed in the W-Ni 50 Ti 50 and W-Ni 44 Ti 56 composites and brittle Ti 2 Ni formed in the W-Ni 42 Ti 58 composites while no brittle intermetallics formed in the W-Ni 42 Ti 53 Nb 5 composite. The W-Ni 42 Ti 53 Nb 5 composite exhibited the sharpest martensitic transformation with the largest transformation enthalpy among the four different composites. The W-Ni 42 Ti 53 Nb 5 composite exhibited a double-yielding phenomenon under compression with an ultimate compressive strength of 3820 MPa and a deformation of 50.4%. In-situ synchrotron high-energy Xray diffraction measurements revealed the first yielding was caused by the martensite reorientation of the NiTi matrix and the second was due to the commencement of massive plastic deformation of the reoriented martensite and is also attributed to the microscopic internal fracturing of the W particles.

36 MATERIALS SCIENCE↗

Mechanical properties of SiC composites neutron irradiated under light water reactor relevant temperature and dose conditions

Silicon carbide (SiC) fiber–reinforced SiC matrix (SiC/SiC) composites are being actively investigated for use in accident-tolerant core structures of light water reactors (LWRs). Owing to the limited number of irradiation studies previously conducted at LWR-coolant temperature, this paper examined SiC/SiC composites following neutron irradiation at 230–340 °C to 2.0 and 11.8 dpa in the High Flux Isotope Reactor. The investigated materials were chemical vapor infiltrated (CVI) SiC/SiC composites with three different reinforcement fibers. The fiber materials were monolayer pyrolytic carbon (PyC) -coated Hi-Nicalon™ Type-S (HNS), Tyranno™ SA3 (SA3), and SCS-Ultra™ (SCS) SiC fibers. The irradiation resistance of these composites was investigated based on flexural behavior, dynamic Young's modulus, swelling, and microstructures. There was no notable mechanical properties degradation of the irradiated HNS and SA3 SiC/SiC composites except for reduction of the Young's moduli by up to 18%. The microstructural stability of these composites supported the absence of degradation. In addition, no progressive swelling from 2.0 to 11.8 dpa was confirmed for these composites. On the other hand, the SCS composite showed significant mechanical degradation associated with cracking within the fiber. Finally, this study determined that SiC/SiC composites with HNS or SA3 SiC/SiC fibers, a PyC interphase, and a CVI SiC matrix retain their properties beyond the lifetime dose for LWR fuel cladding at the relevant temperature.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Power factor improvement in hydrothermally synthesized Bi{sub 2-x}Sb{sub x}Te{sub 3} (x=1.5) - carbon sphere composites

We report fabrication of compacted Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} composites by adding 1 wt% of carbon spheres in the hydrothermal synthesis. The processing parameter of sintering temperature is investigated in order to optimize the thermoelectric power factor of pressed Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} composites. As a result, we find that the composite sintered at 360 Degree-Sign C shows the best power factor performance among the composites and has a largest power factor of 15.4 {mu}W/cm K{sup 2} at 205 K and 13.5 {mu}W/cm K{sup 2} at 290 K. When compared with the samples without addition of carbon sphere in the hydrothermal synthesis, the composites sintered at 340 Degree-Sign C and 360 Degree-Sign C both surpass the largest power factor of 12.1 {mu}W/cm K{sup 2} at 280 K and 11.9 {mu}W/cm K{sup 2} at 290 K for the 340 Degree-Sign C-sintered counterpart. - Graphical abstract: Compacted Bi{sub 0.5}Sb{sub 1.5}Te{sub 3-{delta}} composites obtained by adding 1 wt% of carbon spheres in the hydrothermal synthesis. The composites sintered at 340 Degree-Sign C and 360 Degree-Sign C both surpass the largest power factor of 12.1 {mu}W/cm K{sup 2} at 280 K and 11.9 {mu}W/cm K{sup 2} at 290 K for the 340 Degree-Sign C-sintered counterpart. Highlights: Black-Right-Pointing-Pointer Fabrication of Bi{sub 0.5}Sb{sub 1.5}Te{sub 3-{delta}} composites. Black-Right-Pointing-Pointer Addition of 1 wt% carbon spheres in the hydrothermal synthesis. Black-Right-Pointing-Pointer Investigation of sintering temperature using encapsulating-and-sintering techniques. Black-Right-Pointing-Pointer 360 Degree-Sign C-sintered composite showing the largest power factor of 15.4 {mu}W/cm K{sup 2} at 205 K. Black-Right-Pointing-Pointer 10-60% improvement over the counterpart without adding carbon spheres.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of the correlation between the interfaces and failure behaviors for particle reinforced Mg–Li composites

The interfacial microstructure of SiC{sub p} or YAl{sub 2p} reinforced Mg–14Li–3Al matrix composites was comparatively characterized by scanning electron microscopy and electron probe microanalysis. A nanoindentation combined with scanning electron microscopy technique was used to characterize the interfacial mechanical properties between the reinforcements and matrix. The interfacial strength and failure behaviors for the composites were analyzed from the load–penetration curves and corresponding images. In situ tensile tests were used to observe the fracture and deformation processes with the aid of scanning electron microscopy. The results show that both the chemical and mechanical compatibilities between the YAl{sub 2} particles and LA143 matrix are better than those between the SiC particles and LA143 matrix. The interfacial breakage load for the SiC/LA143 composite is lower than that for the YAl{sub 2}/LA143 composite because of the worse chemical and mechanical compatibilities between the ceramic particles and metal matrix. Interfacial breakage is the main failure mechanism for the SiC/LA143 composite, while the particle breakage and matrix crack are the main failure mechanism for the YAl{sub 2}/LA143 composite. These may be related to the stronger interfacial bonding between the intermetallic particles and metal matrix. - Highlights: • The compatibility for YAl{sub 2} particle with LA143 matrix is better than SiC particle. • The strength of the YAl{sub 2}/LA143 interface is higher than the SiC/LA143 interface. • The main failure behavior for the SiC/LA143 composite is interfacial breakage. • The main failure behavior for YAl{sub 2}/LA143 composite is particle and matrix breakage. • The interfacial strength plays an important role on the composite failure behavior.

36 MATERIALS SCIENCE↗

Development of an in-situ multi-component reinforced Al-based metal matrix composite by direct metal laser sintering technique — Optimization of process parameters

In the present investigation, an in-situ multi-component reinforced aluminum based metal matrix composite was fabricated by the combination of self-propagating high-temperature synthesis and direct metal laser sintering process. The different mixtures of Al, TiO{sub 2} and B{sub 4}C powders were used to initiate and maintain the self-propagating high-temperature synthesis by laser during the sintering process. It was found from the X-ray diffraction analysis and scanning electron microscopy that the reinforcements like Al{sub 2}O{sub 3}, TiC, and TiB{sub 2} were formed in the composite. The scanning electron microscopy revealed the distribution of the reinforcement phases in the composite and phase identities. The variable parameters such as powder layer thickness, laser power, scanning speed, hatching distance and composition of the powder mixture were optimized for higher density, lower porosity and higher microhardness using Taguchi method. Experimental investigation shows that the density of the specimen mainly depends upon the hatching distance, composition and layer thickness. On the other hand, hatching distance, layer thickness and laser power are the significant parameters which influence the porosity. The composition, laser power and layer thickness are the key influencing parameters for microhardness. - Highlights: • The reinforcements such as Al{sub 2}O{sub 3}, TiC, and TiB{sub 2} were produced in Al-MMC through SHS. • The density is mainly influenced by the material composition and hatching distance. • Hatching distance is the major influencing parameter on porosity. • The material composition is the significant parameter to enhance the microhardness. • The SEM micrographs reveal the distribution of TiC, TiB{sub 2} and Al{sub 2}O{sub 3} in the composite.

36 MATERIALS SCIENCE↗

Electrospinning preparation and photoluminescence properties of poly (methyl methacrylate)/Eu{sup 3+} ions composite nanofibers and nanoribbons

Graphical abstract: Nanofibers and nanoribbons of poly (methyl methacrylate)/Eu{sup 3+} ions composites were successfully prepared by using a simple electrospinning technique. And the photoluminescence properties of the above PMMA/Eu{sup 3+} ions composites were studied. Highlights: Black-Right-Pointing-Pointer Nanofibers and nanoribbons of PMMA/Eu{sup 3+} ions composites are fabricated by electrospinning. Black-Right-Pointing-Pointer Photoluminescence properties of as-electrospun PMMA/Eu{sup 3+} ions composites are studied. Black-Right-Pointing-Pointer The ratios of electric- and magnetic-dipole transitions are enhanced by increasing electrospinning voltage. -- Abstract: Nanofibers and nanoribbons of poly (methyl methacrylate) (PMMA)/Eu{sup 3+} ions composites with different concentration of Eu{sup 3+} ions were successfully prepared by using a simple electrospinning technique. From the results of scanning electron microscopy and energy-dispersive X-ray spectroscopy, we found that the morphology of the as-electrospun PMMA/Eu{sup 3+} ions composites could be changed from fiber to ribbon structure by adjusting the concentration of Eu{sup 3+} ions in the electrospun precursor solution. The coordination between the Eu{sup 3+} ions and PMMA molecules were investigated by Fourier transform infrared spectroscopy and differential thermal analysis. The photoluminescence (PL) properties of the as-electrospun PMMA/Eu{sup 3+} ions composites were studied in comparison to those of the Eu(NO{sub 3}){sub 3} powder. It was showed that the {sup 5}D{sub 0}-{sup 7}F{sub J} (J = 0, 1, 2, 3, 4) emission appeared in the PL spectra of the as-electrospun PMMA/Eu{sup 3+} ions composites, whereas the {sup 5}D{sub 0}-{sup 7}F{sub 0} emission was completely absent in the PL spectra of Eu(NO{sub 3}){sub 3} powder due to the different local environments surrounding Eu{sup 3+} ions. It was interesting to note that the intensity ratios of the electric-dipole and magnetic-dipole transitions for the PMMA/Eu{sup 3+} ions composites could be enhanced significantly by increasing electrospinning voltage.

36 MATERIALS SCIENCE↗

In situ formation of sintered cordierite–mullite nano–micro composites by utilizing of waste silica fume

Highlights: ► We succeeded to obtain in situ formed sintered cordierite–mullite nano–macro composites from waste and pure materials at 1400 °C. ► Their sinterability was greatly dependent on both firing temperature and composition. ► XRD patterns showed that the optimum temperature required for formation of sintered cordierite–mullite nano–macro composites was achieved at 1400 °C. ► The batch containing 70 wt.% cordierite and 30 wt.% mullite exhibited the best properties. ► Microstructures of the densified composites were composed of nano–macro cordierite–mullite structures. -- Abstract: This study aims at in situ formation of sintered cordierite–mullite nano–macro composites having high technological properties using waste silica fume, calcined ball clay, calcined alumina, and magnesia as starting materials. The starting materials were mixed in different ratios to obtain different cordierite–mullite composite batches in which the cordierite contents ranged from 50 to 100 wt.%. The batches were uni-axially pressed at 100 MPa and sintered at 1350, 1400 and 1450 °C to select the optimum temperature required for cordierite–mullite nano–macro composites formation. The formed phases were identified by X-ray diffraction (XRD) pattern. The sintering parameters in terms of bulk density (BD) and apparent porosity (AP) were determined. The microstructure of composites has been investigated by scanning electron microscope (SEM). Cold crushing strength (CCS) of the sintered batches was evaluated. The result revealed that the cordierite–mullite nano–macro composites were in-situ formed at 1400 °C. The batch containing 70 wt.% cordierite showed good physical and mechanical properties.

36 MATERIALS SCIENCE↗

Preparation of graphene–Ag composites and their application for electrochemical detection of chloride

Highlights: ► Graphene–Ag composites were prepared in situ using ascorbic acid as green reducing agent. ► The morphology of Ag particles was irregular sheet and Ag particles homogeneously distributed on the graphene matrix. ► The surface-enhanced Raman scattering enhancement factor of D band is 5.85 for composites. ► The composites exhibited good sensitivity for the detection of chloride ions. -- Abstract: Graphene–Ag composites were prepared in situ using ascorbic acid as green reducing agent. The composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected-area electronic diffraction (SAED), and Raman spectrometer. It was showed that Ag particles homogeneously distributed on the graphene matrix. The morphology of Ag particles was irregular sheet with (1 1 1) basal plane. The surface-enhanced Raman scattering (SERS) enhancement factor of D band is 5.85 for composites. The application of the composites for electrochemical detection of chloride was studied by cyclic voltammetry. The composites exhibited good sensitivity for the detection of chloride ions. The maximum peak current of cyclic voltammetry curve in 5 mM KCl was 0.80 mA. In the range of 500 μM to 50 mM for Cl{sup −}, the current response was proportional and linear to the Cl{sup −} concentration. The sensitivity to the detection for Cl{sup −} was 0.059 (mA/mM) and the detection limit was 61 μM for Cl{sup −}. It indicates graphene–Ag composites would be a competitive material for detection of halide.

36 MATERIALS SCIENCE↗

Synthesis and characterization of a novel tube-in-tube nanostructured PPy/MnO{sub 2}/CNTs composite for supercapacitor

Graphical abstract: A novel tube-in-tube nanostructured PPy/MnO{sub 2}/CNTs composite have been successfully fabricated. Its inner tubules are CNTs and the outer tubules are template-synthesized PPy. Most MnO{sub 2} nanoparticles are sandwiched between the inner and outer wall, some relatively large particles are also latched onto the outside wall of the PPy tube. The composite yields a good electrochemical reversibility through 1000 cycles’ cyclic voltammogram (CV) test and galvanostatic charge–discharge experiments at different current densities. Display Omitted Highlights: ► We fabricate a ternary organic–inorganic complex of PPy/MnO{sub 2}/CNTs composite. ► We characterize its morphological structures and properties by several techniques. ► The composite possesses the typical tube-in-tube nanostructures. ► Most MnO{sub 2} nanoparticles are sandwiched between the inner CNTs and outer PPy wall. ► The composite has good electrochemical reversibility for supercapacitor. -- Abstract: Ternary organic–inorganic complex of polypyrrole/manganese dioxide/carbon nanotubes (PPy/MnO{sub 2}/CNTs) composite was prepared by in situ chemical oxidation polymerization of pyrrole in the host of inorganic matrix of MnO{sub 2} and CNTs, using complex of methyl orange (MO)/FeCl{sub 3} was used as a reactive self-degraded soft-template. The morphological structures of the composite were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopic (HRTEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD), respectively. All the results indicate that the PPy/MnO{sub 2}/CNTs composite possesses the typical tube-in-tube nanostructures: the inner tubules are CNTs and the outer tubules are template-synthesized PPy. MnO{sub 2} nanoparticles may either sandwich the space between the inner and outer tubules or directly latch onto the wall of the PPy tubes. The composite yields a good electrochemical reversibility through 1000 cycles’ cyclic voltammogram (CV) test in the potential range of −0.6 to 0.4 V and its specific capacitance was up to 402.7 F g{sup −1} at a current density of 1 A g{sup −1} in galvanostatic charge–discharge experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrothermal synthesis of manganese oxides/carbon nanotubes composites as anode materials for lithium ion batteries

Graphical abstract: Carbon nanotubes in the composites not only accommodate the volume change during charge/discharge processes, but also provide a good electron conducting network at high power rates, resulting in high reversible capacity of the electrodes. - Highlights: • MnO/CNTs composites are obtained by heating Mn{sub 3}O{sub 4}/CNTs at 500 °C for 3 h in flowing Ar/H{sub 2}. • MnO/CNTs electrode exhibits higher specific capacity at the current density of 100 mAh g{sup −1} and a better cycle performance. • Enhancement of cyclability of MnO/CNTs electrode can be attributed to the presence of CNTs in the composites. - Abstract: Mn{sub 3}O{sub 4} nanoparticles and Mn{sub 3}O{sub 4}/carbon nanotubes (CNTs) composites are prepared via a hydrothermal synthesis method. MnO and MnO/CNTs composites are obtained by heating Mn{sub 3}O{sub 4} and Mn{sub 3}O{sub 4}/CNTs at 500 for 3 h in flowing Ar/H{sub 2}. The phase structure, composition and morphology of the composites are characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM). The electrochemical properties of the composite electrodes are studied by performing cyclic voltammetry (CV), galvanostatic charge and discharge tests. The results reveal that the Mn{sub 3}O{sub 4}/CNTs and MnO/CNTs electrodes exhibit higher specific capacity at the current density of 100 mAh g{sup −1} and a better cycle performance than pure Mn{sub 3}O{sub 4} and MnO electrodes. The excellent electrochemical properties of Mn{sub 3}O{sub 4}/CNTs and MnO/CNTs electrodes can be attributed to the presence of CNTs in the composites offering an electron conducting network and suppressing the volume expansion of Mn{sub 3}O{sub 4} and MnO particles efficiently during the charge and discharge processes.

36 MATERIALS SCIENCE↗

Efficient photocatalytic degradation of gaseous formaldehyde by the TiO{sub 2}/tourmaline composites

Graphical abstract: - Highlights: • The TiO{sub 2}/tourmaline composites were prepared by a sol–gel method. • The composites exhibited excellent photocatalytic activity and good stability. • The physicochemical property of tourmaline may be favor for the degradation of HCHO. • The mixed-phase of anatase and rutile TiO{sub 2} may be favor for the degradation of HCHO. - Abstract: The TiO{sub 2} supported tourmaline composites were prepared by a sol–gel method and used as a photocatalyst for the degradation of formaldehyde (HCHO). The composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), N{sub 2} adsorption–desorption, Fourier transform infrared (FT-IR) spectroscopy and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). The results indicate that the mixed-phase of anatase and rutile exists in the TiO{sub 2}/tourmaline composites. The specific surface area of the TiO{sub 2}/tourmaline composites is much higher than that of the pure TiO{sub 2}. The TiO{sub 2}/tourmaline composites exhibited excellent photocatalytic activity for the degradation of HCHO, which was 6 times higher than that of the pure TiO{sub 2}. Moreover, the excellent photocatalytic activity of the composites was fully maintained after five photocatalytic cycles, which may be attributed to the physicochemical property of tourmaline and the mixed-phase of anatase and rutile in the TiO{sub 2}/tourmaline composites.

36 MATERIALS SCIENCE↗

Wet chemical synthesis of ZnO-CdS composites and their photocatalytic activity

Highlights: • ZnO-CdS composites were synthesized by wet chemical method. • TEM, correlated SAED pattern, XRD, and SEM confirmed the structure of composites. • CdS amount added during composites synthesis influences their morphologies. • RhB degradation efficiency is higher for composites than that of pristine ZnO, depending on the catalyst morphology. - Abstract: The present study is focused on the wet chemical synthesis and the characterization of ZnO-CdS composites. The X-ray diffraction shows that the composites contain ZnO in hexagonal wurtzite structure and CdS in cubic phase. The scanning/transmission electron microscopy images reveal flower-like structures with different sizes depending on the CdS content. The optical investigations on composites reveal that the reflectance spectra disclose two thresholds of ∼370 nm and ∼460 nm associated with the ZnO and CdS, respectively. The photocatalytic activity measurements evidenced that the degradation efficiency of RhB in the presence of composites is higher comparatively with pristine ZnO, depending on the catalyst morphology, which varies with CdS content and the pH value of RhB solution. The electron paramagnetic resonance revealed the presence of the paramagnetic point defects in the samples. Thus, the wet chemical approaches are suitable for a large scale production of such ZnO-CdS composites having enhanced photocatalytic activity.

36 MATERIALS SCIENCE↗

Influence of assumptions about household waste composition in waste management LCAs

Highlights: Black-Right-Pointing-Pointer Uncertainty in waste composition of household waste. Black-Right-Pointing-Pointer Systematically changed waste composition in a constructed waste management system. Black-Right-Pointing-Pointer Waste composition important for the results of accounting LCA. Black-Right-Pointing-Pointer Robust results for comparative LCA. - Abstract: This article takes a detailed look at an uncertainty factor in waste management LCA that has not been widely discussed previously, namely the uncertainty in waste composition. Waste composition is influenced by many factors; it can vary from year to year, seasonally, and with location, for example. The data publicly available at a municipal level can be highly aggregated and sometimes incomplete, and performing composition analysis is technically challenging. Uncertainty is therefore always present in waste composition. This article performs uncertainty analysis on a systematically modified waste composition using a constructed waste management system. In addition the environmental impacts of several waste management strategies are compared when applied to five different cities. We thus discuss the effect of uncertainty in both accounting LCA and comparative LCA. We found the waste composition to be important for the total environmental impact of the system, especially for the global warming, nutrient enrichment and human toxicity via water impact categories.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Lepidocrocite Titanate–Graphene Composites for Sodium-Ion Batteries

To overcome electronic transport issues of layered titanates in sodium-ion batteries, we have designed and synthesized composites of lepidocrocite titanates with reduced graphene oxide through a solution-based self-assembly approach. The parent lepidocrocite titanate (K 0.8 [Ti 1.73 Li 0.27 ]O 4 ) was exfoliated by a soft-chemical approach and mechanical shaking. Exfoliated layered titania sheets (LTO) were then combined with reduced graphene oxide (rGO) layers to assemble into composites through flocculation. Countercations (i.e., Mg 2+ ) were used for the self-assembly of negatively charged titania and rGO nanosheets via flocculation. The carbon content in the composites was tuned from 1 to 17% by changing the ratio of titania and rGO sheets in the mixed colloidal suspensions. Electrodes were processed with as-prepared LTO-rGO composites without any carbon additives and tested in sodium half-cell configurations. Mg + -coagulated LTO-rGO composite electrodes deliver higher capacities than electrodes prepared with coagulated titania sheets and 10% acetylene black in sodium half-cells and display good capacity retention after 50 cycles. Electrochemical impedance spectroscopy results indicate lower charge transfer resistance for LTO-14.5%rGO composites than that of coagulated titania sheets with 10% acetylene black. A power law analysis of cells containing the composites indicate a hybrid mechanism consisting of both surface and diffusional processes. A comparison with a similar system, that of dopamine-derived LTO-C heterostructures, reveal significant differences. While capacities showed a strong dependence on carbon content for the dopamine-derived materials, this was not true for the LTO-rGO composites. Instead, the highest capacity was obtained for the 14.5% rGO sample, with a lower value obtained for the 17% rGO sample. A greater proportion of the redox processes were surface rather than diffusional in nature for the LTO-rGO composites as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unusual electronic transport in (1 - x )Cu 2 Se-( x )CuInSe 2 hierarchical composites

The ability to control the relative density of electronic point defects as well as their energy distribution in semiconductors could afford a systematic modulation of their electronic, optical, and optoelectronic properties. Using a model binary hybrid system Cu 2 Se–CuInSe 2 , we have investigated the correlation between phase composition, microstructure, and electronic transport behavior in the synthesized composites. We found that both Cu 2 Se and CuInSe 2 phases coexist at multiple length scales, ranging from sub-ten nanometer to several micrometers, leading to the formation of a hybrid hierarchical microstructure. Astonishingly, the electronic phase diagram of the (1 - x)Cu 2 Se–(x)CuInSe 2 (15% ≤ x ≤ 100%) hierarchical composites remarkably deviates from the trend normally expected for composites between a heavily doped semiconductor (Cu 2 Se) and a poorly conducting phase (CuInSe 2 ). A sudden 3-fold increase in the electrical conductivity and carrier concentration along with a marginal increase in the carrier mobility is observed for composites at the vicinity of equimolar composition (48% ≤ x ≤ 52%). The carrier concentration increases from ~1.5 × 10 20 cm -3 for the composites with x ≤ 45% to 5.0 × 10 20 cm -3 for x = 50%, and remains constant at 4.5 × 10 20 cm -3 with x value in the range of 52% < x ≤ 90%, then quickly drops to 8 × 10 18 cm -3 for pristine CuInSe 2 phase (x = 100%). The atypical electronic behavior was rationalized in the light of the formation of an inter-band (IB) within the band gap, which arises from the hybridization of native electronic point defects from both Cu 2 Se and CuInSe 2 phases in the resulting hierarchical composites. The result points to a new strategy to modulate the electronic structure of semiconductor composites to maximize interaction and coupling between two fundamentally contrasting properties enabling access to electronic hybrid systems with potential applications as interactive and stimuli-responsive multifunctional materials.

36 MATERIALS SCIENCE↗

Design of step composition gradient thin film transistor channel layers grown by atomic layer deposition

In this study, we proposed the artificially designed channel structure in oxide thin-film transistors (TFTs) called a “step-composition gradient channel.” We demonstrated Al step-composition gradient Al-Zn-O (AZO) channel structures consisting of three AZO layers with different Al contents. The effects of stacking sequence in the step-composition gradient channel on performance and electrical stability of bottom-gate TFT devices were investigated with two channels of inverse stacking order (ascending/descending step-composition). The TFT with ascending step-composition channel structure (5 → 10 → 14 at. % Al composition) showed relatively negative threshold voltage (−3.7 V) and good instability characteristics with a reduced threshold voltage shift (Δ 1.4 V), which was related to the alignment of the conduction band off-set within the channel layer depending on the Al contents. Finally, the reduced Al composition in the initial layer of ascending step-composition channel resulted in the best field effect mobility of 4.5 cm{sup 2}/V s. We presented a unique active layer of the “step-composition gradient channel” in the oxide TFTs and explained the mechanism of adequate channel design.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural, thermal and electrical characterizations of multiwalled carbon nanotubes and polyaniline composite

The undoped and doped composite of MWNTs (Multiwalled Carbon Nanotubes) with PANI (/Polyaniline) was prepared by chemical oxidative polymerization. The MWNTs/PANI composites have been characterized by using various techniques like Thermogravometric Analysis (TGA), Fourier transform infrared (FT-IR) spectrometer and Field emission scanning electron microscope (FE-SEM) and conductivity measurement by using two probe method. TGA results has shown that thermal stability followed the pattern undoped MWNTs/PANI composite < doped MWNTs/PANI composite. FE-SEM micrographs demonstrated the morphological changes on the surface of MWNTs as a result of composite formation. Fourier transformed infrared (FT-IR) spectra ascertained the formation of the composite. Study of electrical characteristics demonstrated that the doped MWNTs/PANI composite (1.2 × 10{sup 1} Scm{sup −1}) have better conductivity than the undoped MWNTs/PANI composite (10{sup −4} Scm{sup −1}). These CNTs based polymeric composites are of great importance in developing new nano-scale devices for future chemical, mechanical and electronic applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The effect of nanoparticle enhanced sizing on the structural health monitoring sensitivity and mechanical properties of carbon fiber composites

With current carbon composites being introduced into new commercial market sectors, there is an opportunity to develop multifunctional composites, which are poised to be the next generation of composites that will see future commercial applications. This multifunctional attribute can be achieved via integrated nanomaterials, which are currently under-utilized in real-world applications despite significant research efforts focused on their synthesis. This research utilizes a simple, scalable approach to integrate various nanomaterials into carbon fiber composites by embedding the nanomaterials in the epoxy fiber sizing. Illustrated in this work is the effect of silicon carbide nanoparticle concentrations and dimensions on the structural health monitoring sensitivity of unidirectional carbon fiber composites. Additionally, the nanoparticles contribute to the overall damping property of the composites thus enabling tunable damping through simple variations in nanoparticle concentration and size. Not only does this nanoparticle sizing offer enhanced sensitivity and tunable damping, but it also maintains the mechanical integrity and performance of the composites, which demonstrates a truly multifunctional composite. Therefore, this research establishes an efficient route for combining nanomaterials research with real-world multifunctional composite applications using a technique that is easily scalable to the commercial level and is compatible with a wide range of fibers and nanomaterials.

Bowland, Christopher↗