Results for “flight data analysis” — Page 41

NASA NTRS1990

Performance Data from a Wind-Tunnel Test of Two Main-rotor Blade Designs for a Utility-Class Helicopter

An investigation was conducted in the NASA Langley Transonic Dynamics Tunnel to evaluate an advanced main rotor designed for use on a utility class helicopter, specifically the U.S. Army UH-60A Blackhawk. This rotor design incorporated advanced twist, airfoil cross sections, and geometric planform. For evaluation purposes, the current UH-60A main rotor was also tested and is referred to as the baseline blade set. A total of four blade sets were tested. One set of both the baseline and the advanced rotors were dynamically scaled to represent a full scale helicopter rotor blade design. The remaining advanced and baseline blade sets were not dynamically scaled so as to isolate the effects of structural elasticity. The investigation was conducted in hover and at rotor advance ratios ranging from 0.15 to 0.4 at a range of nominal test medium densities from 0.00238 to 0.009 slugs/cu ft. This range of densities, coupled with varying rotor lift and propulsive force, allowed for the simulation of several vehicle gross weight and density altitude combinations. Performance data are presented for all blade sets without analysis; however, cross referencing of data with flight condition may be useful to the analyst for validating aeroelastic theories and design methodologies as well as for evaluating advanced design parameters.

Singleton, Jeffrey D.↗

NASA NTRS1991

Cloud albedo control by cloud-top entrainment

Marine stratus and stratocumulus clouds exert a considerable influence on the earth's heat budget, mainly due to their high albedos relative to the ocean surface. It is therefore important to understand the processes that control the radiative properties of these extensive cloud systems, particularly during daylight hours. Aircraft measurements of a stratocumulus cloud deck taken around local noon during the 1987 field phase of the First International Satellite Cloud Climatology Project Regional Experiment are the topic of this paper. A mixing line analysis of data from a series of flight tracks across a strong gradient in cloud albedo provides evidence that variations in the water vapor content of the air above the marine inversion can be responsible for the albedo change. The implications of this unexpected result for climate modeling are discussed.

Hanson, Howard P.↗

NASA NTRS1991

Overpressurized zero pressure balloon system

Typical zero pressure scientific balloon systems experiencing diurnal cycles require on board expendable ballast to maintain design float altitude. In the past, pressurized balloon systems have been employed to overcome the need for ballast while maintaining small diurnal altitude excursions. However, requirements on material characteristics and manufacturing methods have enforced limitations on balloon size and therefore payload and altitude capabilities. This effort was aimed at considering the use of current (or slightly modified) zero pressure balloon systems (design, manufacturing and materials) as candidates for pressurized vehicles. Data gathered through performance analysis, structural analysis and flight testing has shown that the use of current zero pressure designs can be expanded to enhance balloon performance.

Simpson, Joel M.↗

NASA NTRS1991

The Automated Logistics Element Planning System (ALEPS)

The design and functions of ALEPS (Automated Logistics Element Planning System) is a computer system that will automate planning and decision support for Space Station Freedom Logistical Elements (LEs) resupply and return operations. ALEPS provides data management, planning, analysis, monitoring, interfacing, and flight certification for support of LE flight load planning activities. The prototype ALEPS algorithm development is described.

Schwaab, Douglas G.↗

NASA NTRS1992

SN 1987A - The impact of greater than 50 MeV gamma-ray luminosity limits on theories of particle acceleration

Analysis of the data obtained from two flights of a balloonborne gamma-ray detector to observe SN 1987A was completed. The detector, which included a spark chamber to determine the arrival directions of the photons, was sensitive in the energy range 50-500 MeV. The 95 percent confidence upper limit to the flux on day 55 after the explosion has been established to be 1.1 x 10 exp -5 photons/sq cm/s and on day 407 to be 3.4 x 10 exp -5 photons/sq cm/s. These limits are compared with various theoretical predictions.

Sood, R. K.↗

NASA NTRS1993

Flight-determined engine exhaust characteristics of an F404 engine in an F-18 airplane

The exhaust characteristics of the F-18 aircraft with an F404 engine are examined with reference to the results of an acoustic flight testing program. The discussion covers an overview of the flight test planning, instrumentation, test procedures, data analysis, engine modeling codes, and results. In addition, the paper presents the exhaust velocity and Mach number data for the climb-to-cruise, Aircraft Noise Prediction Program validation, and ground tests.

Ennix, Kimberly A.↗

NASA NTRS1993

The ion population between 1300 km and 230000 km in the coma of comet P/Halley

During the encounter of the spacecraft Giotto with Comet Halley the two sensors of the ion mass spectrometer (IMS), high energy range spectrometer (HERS) and high intensity spectrometer (HIS), measured the mass and the three-dimensional velocity distributions of cometary ions. HIS looked mainly at the cold, slow part of the distribution close to the nucleus, HERS at the more energetic pick-up ions further out. After a thorough recalibration of the HIS flight spare unit and an extensive data analysis we present here continuous ion density-, composition-, velocity-, and temperature profiles for the water group ion (mass range 16-19 amu/e) along Giotto's inbound trajectory from 230,000 to 1300 km from the comet nucleus. The two sensors are in very good agreement in the region where their measurements overlap thus giving an excellent data base for the discussion of theoretical comet models. The most prominent feature where models and observations disagree is the so called pile up region between 8000 and 15,000 km from the nucleus.

Altwegg, K.↗

NASA NTRS1997

Quantifying the Complexity of Flaring Active Regions

While solar physicists have a better understanding of the importance magnetic fields play in the solar heating mechanism, it is still not possible to predict whether or when an active region will flare. In recent decades, qualitative studies of the changes in active region morphology have shown that there is generally an increase in the complexity of the spatial configuration of a solar active region leading up to a flare event. In this study, we quantify the spatial structure of the region using the differential Box-Counting Method (DBC) of fractal analysis. We analyze data from NASA/Marshall Space Flight Centr's vector magnetograph from two flaring active regions: AR 6089 from June 10, 1990, which produced one M1.7 flare, and AR 6659 from June 8, 9 and 10, 1991, this data set including one C5.7 and two M(6.4 and 3.2) flare. (AR 6659 produced several other flares). Several magnetic parameters are studied, including the transverse and longitudinal magnetic field components (Bt and B1), the total field (Bmag), and the magnetic shear, which describes the non-potentiality of the field. Results are presented for the time series of magnetograms in relation to the timing of flare events.

Stark, B.↗

NASA NTRS2006

The Solar-B Mission: First Light, Future Plans and Community Participation

The Solar-B spacecraft was launched from the Uchinoura Space Center into a circular, sun-synchronous, polar orbit by the Japanese Aerospace Exploration Agency in late September 2006. The spacecraft carries thee scientific instruments designed to follow the flow of magnetic energy from the photosphere to the corona to improve our understanding of both steady state and transient energy release. This goal will be achieved through coordinated observations of three highly advanced solar telescopes developed cooperatively by teams from Japan, the United States and the United Kingdom. The three telescopes are a 0.5m aperture, diffraction limited, solar optical telescope (SOT), an X-ray telescope (XRT) designed for full sun imaging with 1.0 arcsec pixels and an EUV imaging spectrometer (EIS) with an order of magnitude improvement in sensitivity over past instruments. The SOT focal plane contains three instruments, a spectropolarimeter for measuring vector magnetic fields, a broadband filter imager for recording images of the photosphere and chromosphere at the highest resolution the telescope is capable of, and a narrow band filter imager that will record Doppler grams and vector magnetograms. The XRT has broad temperature coverage and a spatial a resolution three times as high as Yohkoh. EIS covers a broad range of transition region and coronal temperatures in two spectral bands. Both XRT and EIS have 2 arcsec spatial resolution (1 arcsec pixels). Instrument first light occurred after five weeks on orbit to allow for out gassing and the opening of the telescopes doors. The initial observation sequences are designed to test the functionality of the different operating modes and for calibration. After this commissioning phase is complete a series of observations are planned to demonstrate the ability of the instruments to meet NASA's mission minimum success criteria. Data is downloaded every orbit to the Norwegian high latitude ground station at Svalbard. The data are transmitted to ISAS where they are reformatted into FITS files and archived as Level 0 data on the ISAS DARTS system. Once the initial observation period is complete, approximately six months after launch, the mission data will be open and freely available to researchers shortly after receipt at the DARTS data archive hosted in Japan and at NASA s Solar Data Analysis Center at the Goddard Space Flight Center. Scientific operations will be conducted from the ISAS facility in Sagamihara, Japan and the observatory will become available for performing joint operations with both ground and space based instruments and for conducting observing programs proposed by non-team members. This process will be described together with a status report from the initial operation of the observatory, showing examples of the first observations.

Davis, John M.↗

NASA NTRS2016

Identification of Fixations in Noisy Eye Movements via Recursive Subdivision

When solving problems, multi-person airline crews can choose whether to work together, or to address different aspects of a situation with a divide and conquer strategy. Knowing which of these strategies is most effective may help airlines develop better procedures and training. This paper concentrates on joint attention as a measure of crew coordination. We report results obtained by applying cross recurrence analysis to eye movement data from two-person crews, collected in a flight simulator experiment. The analysis shows that crews exhibit coordinated gaze roughly one sixth of the time, with a tendency for the captain to lead the first officers visual attention. The degree to which crews coordinate their gaze is not significantly correlated with performance ratings assigned by instructors; further research questions and approaches are discussed.

signal processing↗

NASA NTRS2016

Cross Recurrence Analysis as a Measure of Pilots' Coordination Strategy

When solving problems, multi-person airline crews can choose whether to work together, or to address different aspects of a situation with a divide and conquer strategy. Knowing which of these strategies is most effective may help airlines develop better procedures and training. This paper concentrates on joint attention as a measure of crew coordination. We report results obtained by applying cross recurrence analysis to eye movement data from two-person crews, collected in a flight simulator experiment. The analysis shows that crews exhibit coordinated gaze roughly 1/6th of the time, with a tendency for the captain to lead the first officer’s visual attention. The degree to which crews coordinate their gaze is not significantly correlated with performance ratings assigned by instructors; further research questions and approaches are discussed.

cross recurrence analysis↗

NASA NTRS2016

Cross Recurrence Analysis as a Measure of Pilots' Coordination Strategy

When solving problems, multi-person airline crews can choose whether to work together, or to address different aspects of a situation with a divide and conquer strategy. Knowing which of these strategies is most effective may help airlines develop better procedures and training. This paper concentrates on joint attention as a measure of crew coordination. We report results obtained by applying cross recurrence analysis to eye movement data from two-person crews, collected in a flight simulator experiment. The analysis shows that crews exhibit coordinated gaze roughly 16th of the time, with a tendency for the captain to lead the first officers visual attention. The degree to which crews coordinate their gaze is not significantly correlated with performance ratings assigned by instructors; further research questions and approaches are discussed.

non-linear models↗

NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

NASA’s Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is an enabling technology that facilitates atmospheric entry of heavy payloads to planets such as Earth and Mars using a deployable aeroshell. The deployable nature of the HIAD technology allows it to overcome the size constraints imposed on current rigid aeroshell entry systems. This enables use of larger aeroshells resulting in increased entry system performance (e.g. higher payload mass and/or volume, higher landing altitude at Mars). On November 10th, 2022 the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was launched out of Vandenberg Air Force Base as a secondary payload on an Atlas V rocket. After the primary payload was delivered to its orbit, the LOFTID reentry vehicle was inflated, positioned, and then separated to reenter Earth’s atmosphere at a velocity of 8.1km/s, ultimately splashing down safely in the Pacific Ocean. The flight successfully demonstrated a 6m diameter, 70-deg sphere-cone HIAD on a high-energy orbital reentry. This demonstration has provided invaluable fight data essential to characterize the vehicle performance and support the ongoing effort to further scale the HIAD technology to vehicles of 10m in diameter or greater. Aeroshells of this scale are applicable to near-term commercial applications and future NASA robotic and human exploration missions. LOFTID incorporated an extensive instrumentation suite totaling over 150 science measurements. This included thermocouples, total heat flux sensors, and a radiometer to characterize the aeroheating environment and aeroshell thermal response. An Inertial Measurement Unit (IMU), Global Positioning System (GPS), and flush air data system was included to allow post-flight reconstruction of the vehicle trajectory including a decoupling of the aerodynamics from the atmospheric density. Loadcells were used to measure HIAD structural response during entry, and cameras (both visual-spectrum and infrared) were mounted on the aft segment looking at the aeroshell to monitor structural deflection and surface temperature distribution. Finally, a single up-look camera was included which has provided a surprising amount of science potential from the spectacular footage. In addition to the primary instrumentation suite, a new Fiber Optic Sensing System (FOSS) was used to provide global temperature distributions as a technology demonstration. The system provided over 200 thermal measurements creating a thermal map for the backside of the nose Flexible Thermal Protection System. Another pair of FOSS cables were run along the rigid center structure and measured the temperature response to the vehicle wake environment. The LOFTID instrumentation suite leveraged Agency-wide expertise, with hardware development occurring at Ames Research Center, Langley Research Center, Marshall Space Flight Center, and Armstrong Flight Research Center. This paper will discuss the instrumentation selected for LOFTID, a summary of sensor in-flight performance, and will provide examples of data products from the post-flight analysis effort.

Gregory T Swanson↗

NASA NTRSDate not supplied

Overview and Performance of the LOFTID Instrumentation Suite

NASA’s Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is an enabling technology that facilitates atmospheric entry of heavy payloads to planets such as Earth and Mars using a deployable aeroshell. The deployable nature of the HIAD technology allows it to overcome the size constraints imposed on current rigid aeroshell entry systems. This enables use of larger aeroshells resulting in increased entry system performance (e.g. higher payload mass and/or volume, higher landing altitude at Mars). On November 10th, 2022 the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) was launched out of Vandenberg Air Force Base as a secondary payload on an Atlas V rocket. After the primary payload was delivered to its orbit, the LOFTID reentry vehicle was inflated, positioned, and then separated to reenter Earth’s atmosphere at a velocity of 8.1km/s, ultimately splashing down safely in the Pacific Ocean. The flight successfully demonstrated a 6m diameter, 70-deg sphere-cone HIAD on a high-energy orbital reentry. This demonstration has provided invaluable fight data essential to characterize the vehicle performance and support the ongoing effort to further scale the HIAD technology to vehicles of 10m in diameter or greater. Aeroshells of this scale are applicable to near-term commercial applications and future NASA robotic and human exploration missions. LOFTID incorporated an extensive instrumentation suite totaling over 150 science measurements. This included thermocouples, total heat flux sensors, and a radiometer to characterize the aeroheating environment and aeroshell thermal response. An Inertial Measurement Unit (IMU), Global Positioning System (GPS), and flush air data system was included to allow post-flight reconstruction of the vehicle trajectory including a decoupling of the aerodynamics from the atmospheric density. Loadcells were used to measure HIAD structural response during entry, and cameras (both visual-spectrum and infrared) were mounted on the aft segment looking at the aeroshell to monitor structural deflection and surface temperature distribution. Finally, a single up-look camera was included which has provided a surprising amount of science potential from the spectacular footage. In addition to the primary instrumentation suite, a new Fiber Optic Sensing System (FOSS) was used to provide global temperature distributions as a technology demonstration. The system provided over 200 thermal measurements creating a thermal map for the backside of the nose Flexible Thermal Protection System. Another pair of FOSS cables were run along the rigid center structure and measured the temperature response to the vehicle wake environment. The LOFTID instrumentation suite leveraged Agency-wide expertise, with hardware development occurring at Ames Research Center, Langley Research Center, Marshall Space Flight Center, and Armstrong Flight Research Center. This paper will discuss the instrumentation selected for LOFTID, a summary of sensor in-flight performance, and will provide examples of data products from the post-flight analysis effort.

Greg Swanson↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗

DOE OSTI2012

Comparison of BCF-10, BCF-12, and BCF-20 Scintillating Fibers for Use in a 1-Dimensional Linear Sensor

One-dimensional fiber-bundle arrays may prove useful in a number of radiation sensing applications where radiation detection over large areas is needed. Tests have been performed to evaluate the light generation and transmission characteristics of 15-meter long, 10-fiber bundles of BCF-10, BCF-12, and BCF-20 scintillating fibers (Saint Gobain) exposed to collimated gamma-ray sources. The test set-up used one R9800 (Hamamatsu) photomultiplier tube (PMT) at each end, with a high-speed waveform digitizer to collect data. Time constraints were imposed on the waveform data to perform time-of-flight analysis of the events in the fiber bundles, eliminating spurious noise pulses in the high gain PMTs and also allowing 1-dimensional localization of interactions along the lengths of the fiber bundles. This paper will present the results of these measurements including the attenuation coefficients of the two fiber types and the timing resolution (position uncertainty) possible for each fiber bundle when using the R9800 PMTs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

NASA NTRS1993

Welding process modelling and control

The research and analysis performed, and software developed, and hardware/software recommendations made during 1992 in development of the PC-based data acquisition system for support of Welding Process Modeling and Control is reported. A need was identified by the Metals Processing Branch of NASA Marshall Space Flight Center, for a mobile data aquisition and analysis system, customized for welding measurement and calibration. Several hardware configurations were evaluated and a PC-based system was chosen. The Welding Measurement System (WMS) is a dedicated instrument, strictly for the use of data aquisition and analysis. Although the WMS supports many of the functions associated with the process control, it is not the intention for this system to be used for welding process control.

Romine, Peter L.↗