Search NASA⌕ Search

SEARCH · Search NASA

Results for “influence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Factors influencing mode choice of adults with travel-limiting disability

Introduction: Despite the plethora of research devoted to analyzing the impact of disability on travel behavior, not enough studies have investigated the varying impact of social and environmental factors on the mode choice of people with disabilities that restrict their ability to use transportation modes efficiently. This research gap can be addressed by investigating the factors influencing the mode choice behavior of people with travel-limiting disabilities, which can inform the development of accessible and sustainable transportation systems. Additionally, such studies can provide insights into the social and economic barriers faced by this population group, which can help policymakers to promote social inclusion and equity. Method: This study utilized a Random Parameters Logit model to identify the individual, trip, and environmental factors that influence mode selection among people with travel-limiting disabilities. Here, using the 2017 National Household Travel Survey data for New York State, which included information on respondents with travel-limiting disabilities, the analysis focused on a sample of 8,016 people. In addition, climate data from the National Oceanic and Atmospheric Administration were integrated as additional explanatory variables in the modeling process. Results: The results revealed that people with disabilities may be inclined to travel longer distances walking in the absence of suitable accommodation facilities for other transportation modes. Furthermore, people were less inclined to walk during summer and winter, indicating a need to consider weather conditions as a significant determinant of mode choice. Moreover, low-income people with disabilities were more likely to rely on public transport or walking. Conclusion: Based on this study’s findings, transportation agencies could design infrastructure and plan for future expansions that is more inclusive and accessible, thus catering to the mobility needs of people with travel-limiting disabilities.

99 GENERAL AND MISCELLANEOUS↗

Influence of porous aluminosilicate grain size materials in experimental and modelling Cs + adsorption kinetics and wastewater column process

This paper focuses on the influence of the grain size of a geopolymer based adsorbent on its Cs + adsorption performances both in batch and fixed-bed process. The geopolymer phase was used as a binder to support NaY zeolite particle in a 20 wt% charged porous composite with 160 m 2 .g –1 of porous surface area. These samples were shaped with three grain sizes (50 /100/500 µm) to remove 80–90 mg/g of Cs + in batch and column operations. After their microstructural and porous characterizations, their efficiency and adsorption characteristics were investigated through adsorption isotherms and kinetic in the two processes. While the grain size has no influence on the maximal extraction capacity of the adsorbent, it strongly affects the sorption kinetic. By coupling experimental data and a modelling approach, the complex sorption mechanism was highlighted, suggesting a new insight of the contaminant sorption kinetic. Then, comparison of batch and column adsorption experiments illustrates the detailed explanation of various process parameters for column study. The results show challenges for fixed-bed column utilization by the choice of the appropriate grain size as a compromise between the material sorption kinetic and hydrodynamic considerations. Furthermore, this is of high importance to more accurately optimize the design of column adsorption to assess the transport of Cs+ in multi-porous tailored grain size materials.

36 MATERIALS SCIENCE↗

The influence of collagen support and ionic species on the morphology of collagen/hydroxyapatite composite materials

The purpose of this investigation is to study the influence of collagenous supports and ionic species on the precipitation of hydroxyapatite (HA) from aqueous solutions. To this end, we obtained hydroxyapatite by co-precipitation from a solution of calcium hydroxide and sodium dihydrogenophosphate. The formation of HA was studied by energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The results of this study indicate that the morphology of hydroxyapatite is highly influenced by the support material and the ionic species present. The obtained materials were studied by scanning electron microscopy (SEM).

36 MATERIALS SCIENCE↗

Stability of molybdenum nanoparticles in Sn-3.8Ag-0.7Cu solder during multiple reflow and their influence on interfacial intermetallic compounds

This work investigates the effects of molybdenum nanoparticles on the growth of interfacial intermetallic compound between Sn-3.8Ag-0.7Cu solder and copper substrate during multiple reflow. Molybdenum nanoparticles were mixed with Sn-3.8Ag-0.7Cu solder paste by manual mixing. Solder samples were reflowed on a copper substrate in a 250 Degree-Sign C reflow oven up to six times. The molybdenum content of the bulk solder was determined by inductive coupled plasma-optical emission spectrometry. It is found that upon the addition of molybdenum nanoparticles to Sn-3.8Ag-0.7Cu solder, the interfacial intermetallic compound thickness and scallop diameter decreases under all reflow conditions. Molybdenum nanoparticles do not appear to dissolve or react with the solder. They tend to adsorb preferentially at the interface between solder and the intermetallic compound scallops. It is suggested that molybdenum nanoparticles impart their influence on the interfacial intermetallic compound as discrete particles. The intact, discrete nanoparticles, by absorbing preferentially at the interface, hinder the diffusion flux of the substrate and thereby suppress the intermetallic compound growth. - Highlights: Black-Right-Pointing-Pointer Mo nanoparticles do not dissolve or react with the SAC solder during reflow. Black-Right-Pointing-Pointer Addition of Mo nanoparticles results smaller IMC thickness and scallop diameter. Black-Right-Pointing-Pointer Mo nanoparticles influence the interfacial IMC through discrete particle effect.

36 MATERIALS SCIENCE↗

Optical properties of tin oxide nanoparticles prepared by laser ablation in water: Influence of laser ablation time duration and laser fluence

Colloidal tin oxide nanoparticles are prepared by laser (having a wavelength of 1064 nm) ablation of tin metallic target immersed in pure deionized water. The influences of laser ablation time and laser fluence on the size and optical properties of the synthesized nanoparticles are studied. Prepared tin oxide nanoparticles are characterized by transmission electron microscope, selected area electron diffraction and UV-Visible absorption spectroscopy. The morphology of prepared tin oxide nanoparticles is found to be mostly spherical and with sizes in the nanometric range (mean radius of 3.2 to 7.3 nm). The measured UV-Visible absorption spectra show the presence of absorption peaks in the ultraviolet region. The band gap energy of samples prepared with different laser ablation time duration is calculated and is found to be increased with decrease in size (radius) of the prepared nanoparticles. Photoluminescence emission measurements at room temperature show that all the samples exhibit photoluminescence in the visible region. The peak photoluminescence emission intensity in the sample prepared with 50 min of laser ablation time is 3.5 times larger than that obtained in the sample prepared with 10 min of laser ablation time. - Highlights: Black-Right-Pointing-Pointer SnO{sub 2} nanoparticles (6.4-14.6 nm) are prepared by laser ablation in liquid technique. Black-Right-Pointing-Pointer The influences of laser ablation time and laser fluence are studied. Black-Right-Pointing-Pointer Samples are characterized by TEM and UV-Visible absorption spectroscopy. Black-Right-Pointing-Pointer UV-Visible absorption spectra exhibit quantum confinement effect. Black-Right-Pointing-Pointer Samples exhibit enhanced photoluminescence emissions in the visible region.

36 MATERIALS SCIENCE↗

Influence of ball milling on atomic structure and magnetic properties of Co{sub 40}Fe{sub 22}Ta{sub 8}B{sub 30} glassy alloy

The influence of ball milling on the atomic structure and magnetic properties of the Co{sub 40}Fe{sub 22}Ta{sub 8}B{sub 30} metallic glass with a high thermal stability and excellent soft magnetic properties has been investigated. After 14 h of milling, the obtained powders were found to consist mainly of an amorphous phase and a small fraction of the (Co,Fe){sub 21}Ta{sub 2}B{sub 6} nanocrystals. The changes in the reduced pair correlation functions suggest noticeable changes in the atomic structure of the amorphous upon ball milling. Furthermore, it has been shown that milling is accompanied by introduction of compressive and dilatational sites in the glassy phase and increasing the fluctuation of the atomic-level hydrostatic stress without affecting the coordination number of the nearest neighbors. Ball milling has decreased the thermal stability and significantly affected the magnetic properties through increasing the saturation magnetization, Curie temperature of the amorphous phase and coercivity. - Highlights: • Ball milling affected the atomic structure of Co{sub 40}Fe{sub 22}Ta{sub 8}B{sub 30} metallic glass. • Mechanically-induced crystallization started after 4 h milling. • Milling increased the fluctuation of the atomic-level hydrostatic stress in glass. • Ball milling influenced the thermal stability and magnetic properties.

36 MATERIALS SCIENCE↗

The influence of alloy composition on residual stresses in heat treated aluminium alloys

The as quenched properties of eight different heat treatable aluminium alloys are related to residual stress magnitudes with the objective being to establish if there is a relationship between the residual stress and the as quenched alloy hardness and strength. Near surface residual stresses were assessed with X-ray diffraction using both the established sin{sup 2}ψ method and the more recent cos α technique. Through thickness residual stresses were also characterised using neutron diffraction. The alloys were chosen to encompass a wide range of strengths. The low to medium strength alloys were 6060 and 6082, medium to high strength 2618A, 2014A, 7075, 7010 and two variants of 7449, while the very high strength alloy was the powder metallurgy alloy N707. To assess the as quenched strength, dynamic hardness and tensile properties were determined from samples tested immediately after quenching to minimise the influence of precipitation hardening by natural aging. In addition, hot hardness measurements were made in situ on samples cooled to simulate quench paths. Within the experimental constraints of the investigation, the distribution of residual stress through the thickness was found to follow the same pattern for all the alloys investigated, varying from tensile in the interior to surface compression. The influence of alloy strength was manifested as a change in the observed residual stress magnitudes, and surface residual stresses were found to vary linearly with as quenched hardness and strength. - Highlights: • As quenched aluminium alloys contain high magnitude residual stresses. • Surface is compressive balance by a tensile core. • As quenched surface residual stress is linear function of alloy strength. • In situ hot hardness demonstrates rapid change in intrinsic hardness during rapid cooling.

36 MATERIALS SCIENCE↗

Influence of vanadium incorporation on the microstructure, mechanical and tribological properties of Nb–V–Si–N films deposited by reactive magnetron sputtering

Composite Nb–V–Si–N films with various V contents (3.7–13.2 at.%) were deposited by reactive magnetron sputtering and the effects of V content on the microstructure, mechanical and tribological properties of Nb–V–Si–N films were investigated. The results revealed that a three-phase structure, consisting of face-centered cubic (fcc) Nb–V–Si–N, hexagonal close-packed (hcp) Nb–V–Si–N and amorphous Si{sub 3}N{sub 4}, co-exists in the Nb–V–Si–N films and the cubic phase is dominant. The hardness and critical load (L{sub c}) of Nb–V–Si–N films initially increased gradually and reached a summit, then decreased with the increasing V content in the films and the maximum values were 35 GPa and 9.8 N, respectively, at 6.4 at.% V. The combination of V into Nb–Si–N film led to the fracture toughness linearly increasing from 1.11 MPa·m{sup 1/2} at 3.7 at.% V to 1.67 MPa·m{sup 1/2} at 13.2 at.% V. At room temperature (RT), the average friction coefficient decreased from 0.80 at 3.7 at.% V to 0.55 at 13.2 at.% V for the Nb–V–Si–N films. The wear rate of Nb–V–Si–N films initially decreased and then increased after reaching a minimum value of about 6.35 × 10{sup −} {sup 7} mm{sup 3}/N·mm at 6.4 at.% V. As the rise of testing temperature from 200 °C to 600 °C, the average friction coefficient of Nb–V–Si–N films decreased with the increase of the testing temperature regardless of V content. However, the wear rate gradually increased for all films. The average friction coefficient and wear rate at RT and elevated temperatures were mainly influenced by the vanadium oxides with weakly bonded lattice planes. - Highlight: • Fcc-Nb–V–Si–N, hcp-Nb–V–Si–N and amorphous Si{sub 3}N{sub 4} co-existed in the films. • The amount of Si{sub 3}N{sub 4} decreased with increasing V content in the films. • Hardness of Nb–V–Si–N film (6.4 at.%) reached a maximum value of 35 GPa. • Addition of V led to the increase of fracture toughness. • Tribological properties were influenced by lubricant wear debris.

36 MATERIALS SCIENCE↗

Influence of the microstructure on the resulting 18R martensitic transformation of polycrystalline Cu−Al−Zn thin films obtained by sputtering and reactive annealing

We report the influence of the microstructure on the martensitic transformation in polycrystalline Cu−Zn−Al thin films with 18R structure. The films are grown in two steps. First, Cu−Al thin films are obtained by DC sputtering. Second, the Zn is introduced in the Cu−Al thin films by the annealing them together with a bulk Cu−Zn−Al reference. The crystalline structure of the films was analyzed by X-ray diffraction and transmission electron microscopy. The martensitic transformation temperature was measured by electrical transport using conventional four probe geometry. It was observed that temperatures above 973 K are necessary for zincification of the samples to occur. The resulting martensitic transformation and its hysteresis (barrier for the transformation) depend on the grain size, topology and films thickness. - Highlights: • Polycrystalline Cu−Al−Zn thin films with nanometric grain size are sintered. • Influence of thermal annealing process on the microstructure is analyzed. • Martensitic transformation of Cu−Al−Zn thin films is strongly affected by the microstructure.

36 MATERIALS SCIENCE↗

Influence of phase composition on microstructure and properties of Mg-5Al-0.4Mn-xRE (x = 0, 3 and 5 wt.%) alloys

The microstructure and mechanical properties investigations of two AME503 and AME505 experimental alloys in as-cast conditions were presented. The investigated materials were fabricated on the basis of the AM50 commercial magnesium alloy with 3 and 5 wt.% cerium rich mischmetal. In the as-cast condition, both experimental alloys were mainly composed of α-Mg, Al{sub 11}RE{sub 3} and Al{sub 10}RE{sub 2}Mn{sub 7} intermetallic phases. Additionally, due to non-equilibrium solidification conditions, a small amount of α + γ divorced eutectic and Al{sub 2}RE intermetallic phase were revealed. The obtained results also show a significant influence of rare earth elements on Brinell hardness, tensile and compression properties at ambient temperature and especially on creep properties at 473 K. Improved alloy properties with a rise in rare earth elements mass fraction results from an increase in Al{sub 11}RE{sub 3} phase volume fraction and suppression of α + γ eutectic volume fraction in the alloy microstructure. Additionally, the influence of rare earth elements on the dendrite arm space value was discussed. The presented results also proved the thermal stability of the intermetallic phases during creep testing. - Highlights: • Two different Mg-5Al-0.4Mn alloys containing 3 and 5 wt.% of rare earth elements were fabricated. • Addition of rare earth elements leads to a reduction of dendrite arm spaces. • Mechanical properties depend on the phase composition of the alloys. • The increase of the rare earth elements content causes rise of the creep resistance.

36 MATERIALS SCIENCE↗

Influence of quenching agent on microstructure, properties and thermal stress of SiC{sub p}/2009 composites

15% vol. SiC{sub p}/2009 composites prepared by powder metallurgy were quenched in room temperature water and 20% polyethylene glycol (PEG) solution respectively, then aged naturally. The influence of quenching agent on microstructure, properties and thermal stress of SiC{sub p}/2009 composites were investigated by means of scanning/transmission electron microscope, hardness and tensile test. The results showed that the number of precipitated phase in water quenched composites increased, with much finer in size and more homogeneous in distribution compared with 20% PEG quenched one. Meanwhile, the density of dislocation in composites by water quenching was also much higher. Intergranular corrosion did not occur with the two quenching agents. The 20% PEG quenched composites exhibited slight lower hardness and higher electrical conductivity than that of water quenched one. The two quenched composites showed same level in tensile strength, but the yield strength of water-quenched composites was higher (8 MPa, 3%). The usage of 20% PEG reduced thermal stress and minimized warping deformation of the parts, it is a more suitable quenching agent for SiC{sub p}/2009 composites in engineering application fields. - Highlights: •SiC{sub p}/2009 composites quenched by water and 20% PEG solution were investigated. •Aging precipitation behavior of SiC{sub p}/2009 composites is sensitive to quenchant. •Influence of quenching agent on properties of SiC{sub p}/2009 composites are minimal. •Quenching with 20% PEG reduces thermal stress of SiC{sub p}/2009 composites remarkably. •20% PEG is a more suitable quenching agent for SiC{sub p}/2009 composites than water.

36 MATERIALS SCIENCE↗

Influence of severe plastic deformation on intermetallic particles in Mg-12 wt.%Zn alloy investigated using transmission electron microscopy

The in-depth microstructural characterization of intermetallic particles in an Mg-12 wt.%Zn binary alloy subjected to a severe plastic deformation is presented. The alloy was processed by four passes via equal channel angular pressing with an applied back pressure at a gradually decreasing temperature and analyzed using transmission electron microscopy techniques to observe the influence of processing on intermetallic particles. The results are compared with the initial state of the material prior to severe plastic deformation. The microstructural evolution of the α-Mg matrix and the Mg{sub 21}Zn{sub 25}, Mg{sub 51}Zn{sub 20} and MgZn{sub 2} was analyzed using bright field imaging, selected area electron diffraction, high-resolution transmission electron microscopy and high-angle annular dark field imaging in scanning mode. The plastic deformation process influenced the α-Mg matrix and each type of intermetallic particle. The α-Mg matrix consisted of two types of areas. The first type of area had a highly deformed structure, and the second type of area had a partially recrystallized structure with an average grain size of approximately 250 nm. The Mg{sub 21}Zn{sub 25} microparticles exhibited distinct forms in the α-Mg matrix that were characterized as a single-crystalline form, a nano-crystalline form and a broken up form. No evidence of Mg{sub 51}Zn{sub 20} nanoparticles within the α-Mg matrix was found in the microstructure, which indicates their dissolution or phase transformation during the deformation process. MgZn{sub 2} nanoparticles exhibited different behavior in both types of α-Mg matrix. Two orientation relationships toward the highly deformed α-Mg matrix were observed; however, there was no relationship toward the partially recrystallized α-Mg matrix. Additionally, the growth of the MgZn{sub 2} nanoparticles was different in the two types of α-Mg matrix. The Mg{sub 51}Zn{sub 20} nanoparticles inside Mg{sub 21}Zn{sub 25} microparticles exhibited a distinct behavior within the single-crystalline or nano-crystalline form of the parent Mg{sub 21}Zn{sub 25} microparticles. The Mg{sub 21}Zn{sub 25} + Mg{sub 51}Zn{sub 20} eutectic compound was confirmed for both forms of the parent Mg{sub 21}Zn{sub 25} microparticles, and the growth of Mg{sub 51}Zn{sub 20} nanoparticles is discussed. - Highlights: •Comprehensive microstructure characterization of Mg-12 wt.%Zn alloy after ECAP-BP •TEM analysis of changes of intermetallic phases caused by SPD •Mg{sub 21}Zn{sub 25} particles exhibit nano-crystalline regions with grain size below 100 nm. •MgZn{sub 2} preserved its orientation relationship toward highly deformed α-Mg after SPD. •Existence of Mg{sub 21}Zn{sub 25} + Mg{sub 51}Zn{sub 20} eutectic remained for each Mg{sub 21}Zn{sub 25} particle form.

36 MATERIALS SCIENCE↗

Negative influence of rafted γ′ phases on 750 °C/750 MPa creep in a Ni-based single crystal superalloy with 4% Re addition

Highlights: • The negative influence of the rafted γ′ phases on creep was investigated. • The rafted sample exhibited a lower creep rate a shorter rupture life. • Fine γ′ phases impeded first the dislocation movement in γ matrix. • Existed superdislocations and the stress release decreased the creep resistance. • Rafted γ′ phases were more easily cut by superdislocations and stacking faults. - Abstract: Specimens with two different γ′ phase microstructures, named as-heat treated sample with cuboidal γ′ phases and pre-rafted sample with N-type rafted γ′ phases, were compared to investigate the negative influence of the rafted γ′ phases on the creep property in a Ni-based single crystal superalloy with 4% Re addition at 750 °C and 750 MPa condition. The results indicated that the sample with cuboidal γ′ phases exhibited a lower creep rate and a longer rupture life compared to that with rafted γ′ phases. Transmission electron microscope examinations showed that lots of fine γ′ phases impeded first the dislocation movement in the channel of γ matrix in the initial primary creep stage before the cuboidal γ′ phases were cut by stacking faults in as-heat treated sample. However, in pre-rafted sample, some existed superdislocations located in rafted γ′ phases and the mismatch stress release at γ/rafted γ′ interface resulting from pre-rafted treatment not only decreased the creep resistance of rafted γ′ phases, but also weakened the γ/rafted γ′ interface pinning effect for dislocation movement. Therefore, the rafted γ′ phases were easily cut by superdislocations and stacking faults resulting in a higher creep rate and a shorter creep life.

36 MATERIALS SCIENCE↗

Influence of velocity of pressing in RCS processed AA8090 Al-Li alloy

Highlights: • For the first time the Influence of RCS on the properties of AA 8090 has been studied by processing velocity. • It is found that the properties vary according to pressing velocity and number of passes. • Reported significant property improvement achieved through the pressing velocity of 1.5mm/s. - Abstract: The effect of the velocity of pressing on grain refinement in AA8090 Al-Li alloy sheets during repetitive corrugation and straightening (RCS) at 300 °C is studied. V-groove corrugation dies and flattening dies were used at three different pressing velocities of 1.5 mm/s, 2 mm/s and 2.5 mm/s. The specimen temperature was maintained at 300 °C. Grain refinement was significantly influenced by the pressing velocity. The samples processed for 8 passes at a pressing velocity of 1.5 mm/s had an improved microhardness value of 104 HV and an increased tensile strength of 405 MPa which is respectively 39% and 113% more than the corresponding values in the parent material. TEM analysis showed that samples processed at a pressing velocity of 1.5 mm/s had in places a grain size down to 50 nm and the EBSD results revealed that the average grain size was 2 μm, with 86% of the total number of grain boundaries of the high angle type.

36 MATERIALS SCIENCE↗

Influence of duplex ageing on secondary α precipitates and mechanical properties of the near β-Ti alloy Ti-55531

Highlights: • High strength β-Ti alloys are widely used for their excellent properties. • To reach an excellent combination of strength and ductility, it is attractive to explore the right heat treatment system. • While compared to the conventional single-step ageing process, duplex ageing could change the development and refinement of secondary α precipitations in near/metastable β-Ti alloys resulting varying in performance. • Therefore it is of scientific significance and engineering value to understand the influence of duplex ageing on the formation of secondary α precipitates and mechanical properties for this type of alloy. - Abstract: This paper presents the results of studies on the microstructure and mechanical properties of a near β-Ti alloy processed with different ageing approaches. Influences of intragranular ultrafine α precipitates and grain boundary α layer on mechanical properties in Ti-55531 alloy were analyzed. The results indicate that the precipitation microstructure of the duplex aged alloy exhibits a uniform size and acicular α precipitated orientation shows an angle of approximately 60°. While the morphology of secondary α precipitates in single-step aged samples appear the irregular distribution and heterogeneous size. With the final ageing time increasing, the morphology of intragranular α precipitates and grain boundary α phase brings out a distinct coarsening. The single-step aged alloy can yield a better combination of the ultimate tensile strength (1265 MPa) and ductility (9%). However, the ultimate tensile strength of the duplex aged alloy even reaches 1368 MPa but it breaks at the stage of elastic deformation. The fracture mode of Ti-55531 alloy changes from predominantly dimple fracture in single-step aged samples to predominantly faceted and cleavage type fracture in duplex aged samples causing by the differences of intragranular α precipitates and the interface between grain boundary α layer and intragranular microstructure.

36 MATERIALS SCIENCE↗

Influence of fabrication on microstructure and heat affected zone width in weldments of nuclear reactor pressure vessel steel

Advanced manufacturing routes such as electron beam welding and powder metallurgy with hot isostatic pressing are increasingly used across energy and aerospace industries, where the reliable prediction of weld behavior and heat affected zone (HAZ) evolution is critical. This study examines how fabrication routes and post-weld heat treatments influence phase distribution, crystallite size, microstrain, and dislocation density in nuclear reactor pressure vessel steels using synchrotron X-ray diffraction (SXRD). Retained austenite occurs only in samples that did not undergo austenitization, whereas an austenitizing heat treatment fully eliminates retained austenite and produces a more uniform microstructure across the weldment in terms of phase fraction, dislocation density, and microstrain. The Rosenthal solution underestimates the HAZ width for powder metallurgy samples. A newly proposed modified Rosenthal solution, reducing density by accounting for porosity, matches the SXRD-measured HAZ width with a 0.65% error. Structure–property correlations reveal that dislocation density correlates strongly with nanohardness in homogenous microstructures, while in heterogenous weldments nanohardness is further influenced by the presence of dissimilar phase boundaries. These findings provide new insight into the thermal and microstructural response of powder metallurgy fabricated steels and offer a framework for optimizing welding procedures and heat treatments in advanced manufacturing applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Thermal behaviour of NaBH{sub 4}-sodalites with alumosilicate framework: Influence of cage water content and the surrounding conditions

Research highlights: {yields} Thermal behaviour of NaBH{sub 4} enclathrated sodalites with alumosilicate framework. {yields} Influence of mixed cage fillings (H{sub 2}O, H{sub 3}O{sub 2}{sup -}, CO{sub 3}{sup 2-}) on thermal behaviour of BH{sub 4}{sup -}. {yields} Extend of intra cage reactions depend on templates and experimental surroundings. {yields} Formation of B(OH){sub 4}{sup -}/BH{sub 3}OH{sup -}, BO(OH){sub 2}{sup -} and finally BO{sub 2}{sup -} inside the cages. {yields} Formation of nepheline with boron in its structure after framework destruction. -- Abstract: Sodalites Na{sub 8}[AlSiO{sub 4}]{sub 6}(BH{sub 4}){sub 1.8}(H{sub 3}O{sub 2}){sub 0.2} and Na{sub 8}[AlSiO{sub 4}]{sub 6}(BH{sub 4})(H{sub 3}O{sub 2}){sub 0.5}(CO{sub 3}){sub 0.25}(H{sub 2}O) were examined to characterize the influence of the mixed cage fillings and the surroundings on the thermal behaviour of enclathrated BH{sub 4}{sup -} and the stability of the alumosilicate framework. The samples were investigated in a NaCl matrix during temperature dependent IR-measurements (TIR) and by thermal analysis in inert atmosphere (helium) and in synthetic air. The thermal products were further characterized by XRD and SEM/EDS. It could be shown that the extent of the BH{sub 4}{sup -} decomposition strongly depends on the cage-fillings of the individual sodalite phase and on the environmental experimental conditions. At low to medium temperatures hydrolysis of BH{sub 4}{sup -} by water molecules from decomposition of H{sub 3}O{sub 2}{sup -} and H{sub 2}O/CO{sub 3}{sup 2-} templates leads to B(OH){sub 4}{sup -}/BH{sub 3}OH{sup -} and via subsequent dehydration to BO(OH){sub 2}{sup -} and finally BO{sub 2}{sup -}. At elevated temperatures direct oxidation of BH{sub 4}{sup -} to BO{sub 2}{sup -} occurs inside the sodalite cages. Further heating results in sodalite framework destruction and finally formation of nepheline with some boron in its structure besides some unknown polymeric borates outside the alumosilicate phase. Framework stability of the sodalites was found to decrease in the direction {yields} heating in NaCl {yields} heating in He-atmosphere {yields} heating in air.

36 MATERIALS SCIENCE↗

Influence of the process parameters on the spray pyrolysis technique, on the synthesis of gadolinium doped-ceria thin film

Graphical abstract: Gas-tight CGO made by spray pyrolysis suitable to be used as SOFC electrolyte. Display Omitted Highlights: ► Dense and crystalline CGO films deposited by spray pyrolysis on various substrates. ► Solvent did not have a strong influence on the film microstructure, defect concentration or thickness. ► The substrate did not have a strong influence on the film microstructure, defect concentration or thickness. ► Films with at least 2.5 μm of thickness presented high impermeability. ► The films obtained are suitable to use as a SOFC electrolyte. -- Abstract: This work presents the results of a process of optimization applied to gadolinia-doped ceria (Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9−x}, or CGO) thin films, deposited by spray pyrolysis (SP). Spray pyrolysis is a high thermal deposition method that combines material deposition and heat treatment. This combination is advantageous since the post-deposition heat treatment step is not necessary. However, stresses are solidified in the coating during the deposition, which may lead to the initiation of a crack in the coating. The aim of this work was to achieve thin, dense, and continuous CGO coatings, which may be used as gas separation membranes and as a solid state electrochemical interfaces. Dense, flat, low-defect substrates such as silica slides, silicon mono crystal wafers, and porous substrates were used as substrates in this work. Cerium ammonium nitrate and gadolinium acetylacetonate were dissolved in ethanol and butyl carbitol to form a precursor solution that was sprayed on the heated substrates. Process parameters such as solvent composition, deposition rate and different heating regimes were analyzed. The microstructure was analyzed by secondary electron microscopy (SEM) and was found that thin, dense, and defect-free films could be produced on dense and porous substrates. The results obtained show that it is possible to obtain a CGO dense film deposited by spray pyrolysis. X-ray diffraction (XRD) analysis showed that the films were crystalline after the deposition without requiring post-deposition heat treatment. The crystallite size does not vary significantly as a function of the annealing temperature.

36 MATERIALS SCIENCE↗