Search NASA⌕ Search

SEARCH · Search NASA

Results for “level sets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Deep electron levels in undoped polycrystalline CdTe annealed in liquid Cd

The method of deep-level transient spectroscopy (DLTS) is used to determine the set of deep electron levels in undoped n-CdTe polycrystals grown by chemical synthesis from vapor phase in highly nonequilibrium conditions and then subjected to annealing in liquid Cd. After annealing, the electron concentration is found to increase from {approx}10{sup 8} to 10{sup 15} cm{sup -3}. Electron traps with deep levels E{sub 1} = 0.84 {+-} 0.03 eV and E{sub 2} = 0.71 {+-} 0.02 eV with total concentration {approx}10{sup 14} cm{sup -3} are dominant in the DLTS spectrum. The role of grain boundaries and intrinsic point defects in formation of deep-level centers and their effect on the value of conductivity after annealing are discussed. A relation between the level E{sub 1} and complexes of intrinsic point defects and relation of the level E{sub 2} to the Cd{sub i} point defect are considered.

36 MATERIALS SCIENCE↗

Contact Analog/Compressed Symbology Heading Tape Assessment

A simulation assessed the performance, handling qualities and workload associated with a contact-analog, world-referenced heading tape as implemented on the Comanche Helmet Integrated Display Sight System (HIDSS) when compared with a screen-fixed, compressed heading tape. Six pilots, four active duty Army Aviators and two civilians flew three ADS-33 maneuvers and a traffic pattern in the Ames Vertical Motion Simulation facility. Small, but statistically significant advantages were found for the compressed symbology for handling qualities, workload, and some of the performance measures. It should be noted however that the level of performance and handling qualities for both symbology sets fell within the acceptable tolerance levels. Both symbology sets yield satisfactory handling qualities and performance in velocity stabilization mode and adequate handling qualities in the automatic flight control mode. Pilot comments about the contact analog symbology highlighted the lack of useful rate of change information in the heading tape and "blurring" due to the rapid movement of the heading tape. These issues warrant further study. Care must be taken in interpreting the operational significance of these results. The symbology sets yielded categorically similar data, i.e., acceptable handling qualities and adequate performance, so while the results point to the need for further study, their operational significance has yet to be determined.

Shively, R. Jay↗

Biota Modeling in EPA’s Preliminary Remediation Goal and Dose Compliance Concentration Calculators for Use in EPA Superfund Risk Assessment: Explanation of Intake Rate Derivation, Transfer Factor Compilation, and Mass Loading Factor Sources

The Preliminary Remediation Goal (PRG) and Dose Compliance Concentration (DCC) calculators are screening level tools that set forth Environmental Protection Agency’s (EPA) recommended approaches, based upon currently available information with respect to risk assessment, for response actions at Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) sites, commonly known as Superfund. The screening levels derived by the PRG and DCC calculators are used to identify isotopes contributing the highest risk and dose as well as establish preliminary remediation goals. Each calculator has a residential gardening scenario and subsistence farmer exposure scenarios that require modeling of the transfer of contaminants from soil and water into various types of biota (crops and animal products). New publications of human intake rates of biota; farm animal intakes of water, soil, and fodder; and soil to plant interactions require updates be implemented into the PRG and DCC exposure scenarios. Recent improvements have been made in the biota modeling for these calculators, including newly derived biota intake rates, more comprehensive soil mass loading factors (MLFs), and more comprehensive soil to tissue transfer factors (TFs) for animals and soil to plant transfer factors (BV’s). New biota have been added in both the produce and animal products categories that greatly improve the accuracy and utility of the PRG and DCC calculators and encompass greater geographic diversity on a national and international scale.

54 ENVIRONMENTAL SCIENCES↗

Scout Benchmark Scenarios for U.S. Building Energy and CO2 Emissions to 2050

Overview and Intended Use Cases: These scenarios establish a range of futures for U.S. buildings sector energy use and CO2 emissions to 2050 using Scout (scout.energy.gov), a reproducible and granular model of U.S. building energy use, emissions, and consumer costs developed by the U.S. national labs for the U.S. Department of Energy's Building Technologies Office (BTO). Scout benchmark scenario data are suitable for the following example use cases: setting high-level policy goals for the U.S. buildings sector to 2050 (e.g., X% building CO2 emissions reductions vs. 2005 levels by 2030, Y% reductions vs. 2005 levels by 2050); exploring the effects of key dynamics driving U.S. buildings sector energy and CO2 emissions to 2050 that could be affected by policy levers (e.g., raising minimum technology performance levels; accelerating electrification and/or retrofit rates; introducing breakthrough technologies to the market); determining priority segments (regions, building types, and end use/technology types) and sequencing of U.S. buildings sector energy and CO2 emissions reductions to 2050 under a given set of assumptions; and/or identifying the energy and emissions impacts or cost effectiveness of specific technologies or operational approaches of interest—in isolation or after considering competition with other measures in a scenario portfolio. Scenario Summary: A total of 8 scenarios explore the effects of changes across both the demand- and supply-side of building energy use on annual U.S. building energy use and CO2 emissions from 2022–2050. Scenarios are organized into three groups representing low, moderate, and best-case potentials for building decarbonization, respectively.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Exposure to particulate hexavalent chromium exacerbates allergic asthma pathology

Airborne hexavalent chromate, Cr(VI), has been identified by the Environmental Protection Agency as a possible health threat in urban areas, due to the carcinogenic potential of some of its forms. Particulate chromates are produced in many different industrial settings, with high levels of aerosolized forms historically documented. Along with an increased risk of lung cancer, a high incidence of allergic asthma has been reported in workers exposed to certain inhaled particulate Cr(VI) compounds. However, a direct causal association between Cr(VI) and allergic asthma has not been established. We recently showed that inhaled particulate Cr(VI) induces an innate neutrophilic inflammatory response in BALB/c mice. In the current studies we investigated how the inflammation induced by inhaled particulate Cr(VI) might alter the pathology of an allergic asthmatic response. We used a well-established mouse model of allergic asthma. Groups of ovalbumin protein (OVA)-primed mice were challenged either with OVA alone, or with a combination of OVA and particulate zinc chromate, and various parameters associated with asthmatic responses were measured. Co-exposure to particulate Cr(VI) and OVA mediated a mixed form of asthma in which both eosinophils and neutrophils are present in airways, tissue pathology is markedly exacerbated, and airway hyperresponsiveness is significantly increased. Taken together these findings suggest that inhalation of particulate forms of Cr(VI) may augment the severity of ongoing allergic asthma, as well as alter its phenotype. Such findings may have implications for asthmatics in settings in which airborne particulate Cr(VI) compounds are present at high levels. -- Highlights: ► Allergic asthma correlated with exposure to certain inhaled particulate chromates. ► Direct causal association between Cr(VI) and allergic asthma not established. ► Cr exacerbated pathology and airway hyperresponsiveness in an OVA-challenged mouse. ► Particulate Cr(VI) may augment severity and alter phenotype of ongoing allergic asthma.

60 APPLIED LIFE SCIENCES↗

Charge transfer and atomic-level pressure in metallic glasses

This paper presents a systematic study on the charge transfer and ionicity in various metallic-glass forming systems, as well as its relationship with other atomic-level structure indicators, using the Bader analysis method and molecular dynamics simulation. It is shown that in a binary or multicomponent system, the chemical effects (when more than one elements present) appear to play a more important role in setting the absolute level of the atomic-level pressure, compared to the topological fluctuation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Water Level Data from Wells PLM1 and PLM6 for the East River Watershed, Colorado

This dataset (Williams et al., 2020) contains the original un-QA/QC-ed water level data for PLM1 and PLM6 and has been obsoleted. The data contained within this dataset is not to be used. Refer to Faybishenko et al., 2022 (DOI: 10.15485/1866836) for the latest QA/QC-ed data available via ESS-DIVE.This data set contains water level data for the PLM1 and PLM6 wells. PLM1 and PLM6 are location identifiers used by the Watershed Function SFA project for two groundwater monitoring wells along an elevation gradient located along the lower montane life zone of a hillslope near the Pumphouse location. These wells used to monitor subsurface water and carbon inventories and fluxes at the East River Watershed, Colorado, USA. Complete metadata information on the PLM1 and PLM6 wells are available in the related data package reference Varadharajan C, et al (2020). https://doi.org/10.15485/1660962.Data are reported in .csv files per well. The latitude and longitude of each location are given in a file called locations.csv. These data are used for determining the seasonally dependent flow of groundwater under the PLM hillslope. The downslope flow of groundwater in combination with data on groundwater chemistry can be used to estimate rates of solute export from the hillslope to the floodplain and river.These data products are part of the Watershed Function Scientific Focus Area collection effort to further scientific understanding of biogeochemical dynamics from genome to watershed scales.

54 ENVIRONMENTAL SCIENCES↗

Heterogeneous energetic material damage simulator (HEDS): A deep learning approach to simulate damage–sensitivity linkages

Damage in the microstructures of energetic materials (EMs), such as propellants and plastic bonded explosives (PBXs), can significantly alter their response to external loads. Both sensitization and desensitization can occur, causing concerns with safety and performance in the field; predictive models that connect damage and the sensitivity of EMs can enable design and provide confidence in their robustness and reliability. However, modeling of damage evolution is challenging for real microstructures of EMs; samples of damaged EMs are difficult to obtain, thereby hindering experiments and direct numerical simulations to determine the sensitivity of EMs at various stages of damage. Here, we develop an approach to generate synthetic, i.e., in silico produced, damaged microstructures for use in simulations to connect damage levels to sensitivity. The development of the present workflow to generate and impose varying levels of damage in microstructures, known as HEDS (Heterogeneous Energetic Material Damage Simulator), begins with a small set of images of damaged PBXs and combines a collection of deep neural network techniques to generate microstructures with varying levels of damage. By making the synthetic microstructures conform closely to those observed in available real, imaged microstructures, we develop an ensemble of damaged microstructures that can be used for in silico shock experiments. HEDS develops these microstructure ensembles as level set fields, which are directly employed in a sharp interface Eulerian hydrocode where shock simulations are performed to quantify the energy release rate from hotspot fields generated in the microstructure. These capabilities can be useful for the analysis and assessment of changes in the sensitivity of EMs and to design formulations that are less susceptible to damage-induced changes in sensitivity and performance.

Fang, Irene (ORCID:0009000844557122)↗

Improved Search for a Higgs Boson Produced in Association with Z{yields}l{sup +}l{sup -} in pp Collisions at {radical}(s)=1.96 TeV

We search for the standard model Higgs boson produced with a Z boson in 4.1 fb{sup -1} of integrated luminosity collected with the CDF II detector at the Tevatron. In events consistent with the decay of the Higgs boson to a bottom-quark pair and the Z boson to electrons or muons, we set 95% credibility level upper limits on the ZH production cross section multiplied by the H{yields}bb branching ratio. Improved analysis methods enhance signal sensitivity by 20% relative to previous searches. At a Higgs boson mass of 115 GeV/c{sup 2} we set a limit of 5.9 times the standard model cross section.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Shocking Results on the Adverse Effects of CO2 Exposures

Carbon dioxide (CO2) is released in large quantities from humans while they live and work in spacecraft or work outside the spacecraft during extravehicular activity (EVA). Removal of this anthropogenic pollutant requires major resources, and these resources increase dramatically as the levels of CO2 set to protect human health and performance are reduced. The current Spacecraft Maximum Allowable Concentration of CO2 aboard the ISS is 0.7% or 5.3 mmHg; however, according to Chits (mission action requests), NASA and its international partners have agreed to control CO2 levels to less than 4 mmHg. In the meantime, retrospective investigations attempting to associate crew symptoms with elevated CO2 levels over the life if the International Space Station (ISS) are underway to determine if this level is sufficient to protect against health and performance decrements. Anecdotal reports suggest that crewmembers are not able to perform complex tasks as readily in spaceflight as they were able during ground-based training. While physiological effects of CO2 have been studied for many decades, it is only recently that the effects of CO2 on higher reasoning capabilities have been studied. The initial results are shocking. For example, one study published in the respected journal Environmental Health Perspectives showed obvious adverse effects of CO2 exposures on higher reasoning at 1.9 mmHg. The implications and limitations of this study are paramount in determining future CO2 SMACs for human spaceflight, both aboard the ISS and in exploration-class missions. Key Words: carbon dioxide, spacecraft, air quality, toxic effects

James, John T.↗

Digital pixel test structures implemented in a 65 nm CMOS process

The ALICE ITS3 (Inner Tracking System 3) upgrade project and the CERN EP R&D on monolithic pixel sensors are investigating the feasibility of the Tower Partners Semiconductor Co. 65 nm process for use in the next generation of vertex detectors. The ITS3 aims to employ wafer-scale Monolithic Active Pixel Sensors thinned down to 20–40 µm and bent to form truly cylindrical half barrels. Among the first critical steps towards the realisation of this detector is to validate the sensor technology through extensive characterisation both in the laboratory and with in-beam measurements. The Digital Pixel Test Structure (DPTS) is one of the prototypes produced in the first sensor submission in this technology and has undergone a systematic measurement campaign whose details are presented in this article. The results confirm the goals of detection efficiency and non-ionising and ionising radiation hardness up to the expected levels for ALICE ITS3 and also demonstrate operation at + 20 °C and a detection efficiency of 99% for a DPTS irradiated with a dose of 10 15 1 MeV n eq cm -2 . Furthermore, spatial, timing and energy resolutions were measured at various settings and irradiation levels.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Photovoltaic-assisted heat pump water heater system and method

A solar power system has a photovoltaic module that supplies electrical current derived from sunlight to a heater system of a hot water tank. The heater system uses the electrical energy from the photovoltaic module, and optionally also from a local power grid, to heat water up to a selected maximum stored hot water temperature. Control circuitry senses when the level of electrical power is below a threshold solar-power level, and in response sets the stored hot water temperature for the heater system to a first lower temperature value. The control circuitry also senses when the level of electrical power is above the threshold solar-power level, an in response sets the stored hot water temperature for the heater system to a second elevated temperature value higher than the lower temperature, making advantageous use of solar power when available. A mixing unit adds cold water to set the dispensed water temperature.

14 SOLAR ENERGY↗

A theoretical investigation of the (0001) covellite surfaces

We report on the properties of the (0001) covellites surfaces, which we investigate by periodic slab density functional theory calculations. The absolute surface energies have been computed for all bulk terminations, showing that surfaces terminated by the flat CuS layer are associated with the lowest surface energy. Cleavage is predicted to occur across the [0001] interlayer Cu–S bond. The surfaces obtained by lowest energy cleavage are analyzed in terms of the atomic vertical relaxation, workfunction, and surface band structure. Our study predicts the presence of a shallow p{sub z}-derived surface state located 0.26 eV below the Fermi level, which is set to play an important role in the surface reactivity of covellite.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Statistical Approach to Establishing Subsystem Environmental Test Specifications

Results are presented of a research task to evaluate structural responses at various subsystem mounting locations during spacecraft level test exposures to the environments of mechanical shock, acoustic noise, and random vibration. This statistical evaluation is presented in the form of recommended subsystem test specifications for these three environments as normalized to a reference set of spacecraft test levels and are thus suitable for extrapolation to a set of different spacecraft test levels. The recommendations are dependent upon a subsystem's mounting location in a spacecraft, and information is presented on how to determine this mounting zone for a given subsystem.

Keegan, W. B.↗

The Classical Equations of Motion of Quantized Gauge Theories, Part I: General Relativity

In this and a companion paper, we show that quantum field theories with gauge symmetries permit a broader class of classical dynamics than typically assumed. In this article, we show that the dynamics extracted from the path integral or Hamiltonian formulation of general relativity allows for classical states that do not satisfy the full set of Einstein's equations. This amounts to loosening the Hamiltonian and momentum constraints that are imposed on the initial state. Nevertheless, the quantum theory permits gauge invariant time evolution of these states. The time evolution of these states is such that at the classical level the full set of Einstein's equations would appear to hold, with the physical effects of these states being attributable to an auxiliary, covariantly conserved energy-momentum tensor with no internal degrees of freedom. We derive the generalized Einstein equations for these states and show that a homogeneous and isotropic initial background state contributes to expansion identical to cold dark matter. The inhomogeneous components of this state could source curvature perturbations that grow linearly at linear order. This auxiliary contribution to Einstein's equations could have either sign and thus provide a trivial way to violate the null energy condition, enabling novel gravitational dynamics such as cosmic bounces and wormholes.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Designing of transparency windows by quantum interference of wave packets

It has been shown that control over the design of single- or multimode-transparency windows can be achieved by control-probe quantum interferometry using two delayed phase-locked ultrashort pulses. We have investigated how single- or multimode-transparency windows can be designed by eliminating the absorption to a set of odd or even vibrational levels of a molecule covered by the spectral bandwidth of the pulses. Suppression of absorption can be achieved by controlling the quantum interference of two vibrational wave packets excited by these two pulses, leading to destructive interference of transition amplitudes for one set of vibrational levels even or odd. Simuntaneously the interference becomes constructive for the other set of odd or even vibrational levels, leading to absorption to these levels. Thus, a set of transparency windows is designed in between two absorption peaks at two consecutive odd (even) vibrational levels by eliminating absorption at even (odd) vibrational levels between two absorption peaks. If the spectral bandwidth of the pulse [full width at half maximum (FWHM)] is less than the energy difference between two consecutive absorption peaks, the pulse will be transmitted without absorption through the transparency window. However, for pulses with a larger spectral bandwidth (FWHM), a set of broad transparency windows will be generated and different bands of pulse frequencies will be transmitted through these windows. We have shown that coherent control of the design of transparency windows can be achieved by controlling pulse duration, carrier frequency, delay, and the phase difference of two ultrashort pulses.

74 ATOMIC AND MOLECULAR PHYSICS↗

Population of the giant pairing vibration

Background: We present that the giant pairing vibration (GPV), a correlated two-nucleon mode in the second shell above the Fermi surface, has long been predicted and expected to be strongly populated in two-nucleon transfer cross sections similar to those of the normal pairing vibration. Recent experiments have provided evidence for this mode in 14,15 C but, despite sensitive studies, it has not been definitively identified in either Sn or Pb nuclei where pairing correlations are known to play a crucial role. Purpose: Our aim is to test whether features inherent to the mixing of bound and unbound levels might account for this and to study the effect in a simple and intuitively clear approach. Method: We study the mixing of unbound levels in a set of toy models that capture the essential physics of the GPV, along with a more realistic calculation including distorted-wave Born approximation transfer amplitudes. Results: The calculated (relative) cross section to populate a simulated GPV state is effectively low, compared to the case of bound levels with no widths Conclusions: The mixing turns out to be only a minor contributor to the weak population. Rather, the main reason is the melting of the GPV peak due to the width it acquires from the low orbital angular momentum single-particle states playing a dominant role in two-nucleon transfer amplitudes. Lastly, this effect, in addition to a severe Q-value mismatch, may account for the elusive nature of this mode in (t,p) and (p,t) reactions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Prediction of correlation energies using variational subspace valence bond

In the variational subspace valence bond (VSVB) [G. D. Fletcher, J. Chem. Phys. 142, 134112 (2015)] method, the electronic orbitals comprising the wave function correspond to chemically meaningful objects, such as bonds, lone pairs, atomic cores, and so on. Selected regions of a molecule (for example, a single chemical bond, as opposed to all the bonds) can be modeled with different levels of basis set and possible methods for modeling correlation from the other regions. The interactions between the components of a molecule (say, a bond and a neighboring orbital) can then be studied in detail for their impact on a chemical phenomenon while avoiding the expense of necessarily applying the higher levels and methods to the entire molecule. Here, this work presents the theoretical basis for modeling correlation effects between specific electron pairs by incorporating terms in the inter-electronic coordinates (“r 12 ”) into VSVB. The approach is validated with calculations on small systems using single-reference wave functions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗