Search NASA⌕ Search

SEARCH · Search NASA

Results for “preforms”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Performance Validation of Advanced PHEV Vehicle

Summary of Major Accomplishments: Ford developed a PHEV Escape as part of a DOE contract to develop a production-ready PHEV prototype. Although conventional certification tests were conducted by Ford during their development, Argonne was brought in at the half-way point and at end of the development project to run their research-oriented benchmark testing on one of their prototype vehicles in different states of controls development. Here are the accomplishments: Prototype vehicle was instrumented by installing voltage and current probes and a resolver was installed for engien speed and position; Other signals were collected such as several temperatures and sett up CAN network data collection. ANL-1060 (10/07/2016) Summary of Major Accomplishments: 51 individual tests were conducted on the 4WD chassis dynamometer in December 2008, in both CD and CS modes over UDDS, US06, HWY, SC03 cycles, and research cycles including preformance and steady-state - 66 individual tests were conducted run on the 4WD chassis dynamometer in Aug 2009, in both CD and CS modes over UDDS, US06, HWY, SC03 cycles, and research cycles including prefoemance and steady-state - Data was analyzed and summarized for DOE in several in-person briefings. One briefing was held in early 2009 and another in the fall of 2009.

33 ADVANCED PROPULSION SYSTEMS↗

Maximizing REE Recovery in Geothermal Systems

Rare Earth element (REE) concentrations were measure in several on-land geothermal systems, many of which boil due to pressure drop during fluid upflow in geothermal production wells. REE were also measured in several seafloor hydrothermal systems sampled at pressures above the boiling point for comparison to boiled systems. Boiling during production lowers REE concentration in fluids sampled at the well head due to changes in fluid pH and Temperature that occur during boiling that affect the solubility of REE mineral phases. Geochemical calculations using the best available thermodynamic data were preformed to extend the understanding of REE behavior beyond the systems sampled for this study. Our data and modeling show that REE concentration in geothermal fluids is controlled by solubility limits, not by concentration in the source rocks. With the exception of La and Ce, the concentration of most of the REE in geothermal fluids are less than one part per trillion. There are no reasonable scenarios under which co-production of REE from geothermal fluids used to produce energy will contribute to the economic viability of the resource.

15 GEOTHERMAL ENERGY↗

Thermoplastic Composites Parts Manufacturing Enabling High Volumes, Low Cost, Reduced Weight with Design Flexibility – Phase 2

The deliverable of this IACMI PHASE II project is an innovative thermoplastic composite parts manufacturing process that addressed some of the most challenging aspects for commercial adoption in high volume market applications with requisite design flexibility while lowering cost and weight. The collaborative 15-month joint effort built upon the collective collateral value that was validated in PHASE I, as well as the synergies of a cross- functional team members comprised & lead by DuPont, Fibrtec & Purdue. Specifically, Fibrtec’s uniquely flexible coated tow (FibrFlex®) with DuPont's Rapid Fabric Formation (RFF) technology and a proprietary DuPont polyamide resin, were used to create near net shapes, while Purdue developed new simulation tools to predict the behavior of material system preforms in molding processes. These were ultimately deployed for the manufacturing with “informed” performance of industrially-interesting CFRP parts. Experiments, modeling, and simulations have shown that this process/materials combination offers advantages for producing lower cost continuous fiber reinforced polymer (CFRP) materials that drape well during molding while maintaining outstanding physical properties. This newly deployed process is ideally suitable for adoption in the automotive and other higher volume industries because of the associated cost savings due to reduction of waste and embodied energy. Furthermore, it overcomes the drawbacks of the prevalent two other typically deployed processes; the slow speed and expensive part formation associated with the usage of the stiff and brittle UD tapes, or the release of short conductive carbon fiber strands into the environment associated by the alternate layering of fiber woven fabric with resin film.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Laser and Electron Beam Technology for Parity Violating Electron Scattering Measurements

Parity violating electron scattering (PVES) is a precision tool used in a broad program of experiments which include studying the structure of protons and nuclei and searching for new Beyond the Standard Model (BSM) physics. In parity violation electron scattering experiments, a longitudinally polarized electron beam is incident on an unpolarized target. The sign of the longitudinal polarization is changed (making a parity transformation), and the fractional rate difference between right and left helicity states, dσ R and dσ L , is measured. An interference between the electromagnetic and weak amplitudes, M γ and M Z respectively, gives rise to a parity violating asymmetry A PV = $\frac{σ_{R}-σ_{L}}{σ_{R}-σ_{L}}$, defined by the fractional rate difference between right and left helicity states. A PV can be measured to extraordinarily high precision and is proportional to the ratio of the weak and electromagnetic amplitudes. This thesis highlights three such PVES experiments as well as a new polarized beam source which will improve their precision. The PVES experiments are PREX-II, MOLLER, and a 12 C transverse asymmetry measurement at Mainz. Chapters 1-3 of this thesis cover introductions to MOLLER and PREX-II, Chapter 4 contains the results of the 12 C transverse asymmetry measurement at Mainz, and Chapters 5-6 contain the original work performed by this author. PREX-II, the Lead Radius Experiment, measures the weak skin of the 208 Pb nucleus, provides a clean measurement of R N , the RMS radius of neutrons in a heavy nucleus, and constrains the equation of state (EOS) of highly dense matter which is important for describing neutron star structure, heavy ion collisions, and atomic parity violation experiments. The 12 C transverse asymmetry measurement at Mainz, and the future Mainz program of measuring the 208 Pb transverse asymmetry as well, addresses an important systematic correction for PREX and other PVES experiments preformed with heavy-nuclei. MOLLER (Measurement Of Lepton Lepton Electroweak Reaction) is an extremely precise PVES experiment searching for new neutral currents in electron-electron scattering. It’s called MOLLER because it will measure A PV in the Moller ee scattering process, and will infer the weak charge of the electron $Q^e_W$ to extremely high precision. MOLLER is sensitive to new Beyond the Standard Model physics at MeV and multi-TeV scales and will serve as an indirect complementary measurement to direct searches at high energy colliders. To achieve high precision measurements on A PV for MOLLER, we have developed an innovative Rubidium Titanyl Phosphate (RTP) Pockels cell in the polarized source to satisfy both statistical and systematic requirements as regards the electron beam produced. This new ultra-fast RTP cell design uses electric field gradients to provide unprecedented control over helicity correlated beam asymmetries and has been demonstrated to be capable of producing precisely controlled polarized electron beam at Jefferson Laboratory, controlling beam steering down to the nm-level. The precision reached with the RTP cell offers sufficient control over and minimization of helicity correlated beam asymmetries to perform PREX II. The RTP Pockels cell system will provide fast flipping and suitable control helicity correlated beam asymmetries and parity quality beam for the future MOLLER experiment, providing an unprecedented precision on the electron weak charge and electroweak mixing angle.

Palatchi, Caryn↗

Energy Efficient Thermoplastic Composite Manufacturing

The objective of the project was to establish an effective and affordable method to lay-up and consolidate/join large thermoplastic composite aerospace structure with cycle times measured in minutes rather than hours. Composite airplane designs have proven efficient and effective however future potential product production rates are challenging what the current systems can efficiently produce due to material lay-down constraints and extended thermal cycle times. The ability to lay-up then rapidly heat, consolidate, and cool large complex composite structures plus very accurately tool them (i.e. matching CTE of composite materials) along with very precise thermal control is a difficult challenge. Current systems such as autoclave processing of thermoset materials require long cycle times due to method of heating and the large associated thermal masses. These extended cycle times inhibit the ability to meet higher rate production scenarios due to the need for multiple sets of equipment and tools. Thermoplastic composite materials were used to facilitate more rapid cycle times via the elimination of a need for a cure dwell at temperature. Also, utilized induction heating along with smart susceptors to enable the quick cycle times needed while providing precise intrinsic thermal control. The intrinsic control of the induction heating process via the smart susceptors along with the use of laser assisted fiber placement were the key innovations areas developed. The ability to rapidly heat and then precisely control the temperature of the consolidation component was paramount to the success of this project. It is this unique processing attribute coupled with the thermoplastic material characteristics along with rapid lay-up methods that are novel and advantageous. While many requirements and influencing factors decide the materials and processes utilized for future airplane construction, the forecast of accelerated production rates and the recent performance successes of composites in airplane construction provide an opportunity for this processing technology to have significant influence. During the course of this project a number of key accomplishments were completed. They are as follows: The needed laser assisted fiber placement capabilities have been developed and validated on a component of meaningful scale and complexity. Subsequently, a thermoplastic preform of the part scale-up part design was laser assisted fiber placed and made availalbe for consolidation. An induction consolidation system was sized, designed, and fabricated resulting in the full capability to consolidate the scale-up component. The tool for induction consolidating of the scale-up component was designed and fabricated. An aluminum pressure bladder was welded and formed for use as the pressurization membrane to perform the needed application of pressure on the part at temperature to achieve consolidation. The induction consolidation system consisting of the restraint, induction power supply, induction tool with integrated induction coils and smart susceptor liners, along with the aluminum bladder were successfully used to consolidate a large thermoplastic skin. The capability of accomplishing rapid heat-up rates and cool down rates for consolidation of large thermoplastic skins with precise thermal control and even pressure application at the consolidation temperature was validated. The general conclusion is that the use of induction consolidation with smart susceptors is an effective method to rapidly and efficiently consolidate large thermoplastic composite components and enable affordable high rate manufacturing of composites. More specific conclusions generated by this project are as follows: A restraint type induction consolidation system provides an affordable option over the standard press when using the induction consolidation processing method. Aluminum bladders can be formed to the complex shapes needed and supply uniform pressure for consolidation and co-consolidation of thermoplastic composite materials. Straightforward modifications can be made to existing fiber placement robotic systems to enable their use for thermoplastic lay-up applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Ultra-Light Hybrid Composite Door Design, Manufacturing and Demonstration

New Corporate Average Fuel Economy regulations require improved fuel efficiency of the future vehicle fleet. Weight reduction is key to achieving these targets. Replacing metallic body and chassis components with carbon fiber-reinforced composites offers the most weight reduction potential at up to 70%. Introduction of the BMW i3 and i8 in 2014 required mass production processes to meet 20,000+ units per year. Preforming with High Pressure Resin Transfer Molding has been implemented and meets rate, cost, and performance requirements. We will advance these technologies to develop an ultra-light driver’s side door for the vehicle with production rates of 40,000 units annually per plant in Detroit, Michigan. This project sought to employ a comprehensive systems approach for designing, manufacturing, and demonstrating an ultra-light hybrid composite automotive door. Composite structural components are integrated with other functional systems to reduce part count and full-system weight by a minimum of 42.5%. The approach will be demonstrated on a driver’s- side front door and will consider all fit, functional, safety, and cost requirements. These concepts will be evaluated using structural and crash simulations and linked to a manufacturing feasibility study, resulting in producible designs of an integrated door system. A cost model will evaluate part of the cost for the various designs and will ensure the cost target of less than $5 per pound of weight saved is met. Hybrid composites consisting of carbon, glass, and metal components will be included in our trade-off studies to satisfy these cost and performance goals.

02 PETROLEUM↗

Development of electronically passivating surfaces to enhance battery performance

For many decades, lithium metal batteries (LMBs) have been studied for their high energy density, though they suffer from high reactivity, which safety concerns such as explosions and fires. These events can occur as a result of degradation due to redox reactions and lithium morphology that evolve during cycling. Mostly, the failure is caused by the electrolyte degradation leading to the creation of a solid electrolyte interphase (SEI), which tends to induce electron leakage, lithium dendrite growth, and capacity decay. SEI formation is practically inevitable. This work investigated the minimization of degradation events by modifying different battery configurations. Modifications were made by exchanging electrolytes, electrode surfaces, and even annexing innovative components. Our goal is to achieve a configuration where Li-ion transfer is facilitated, and electron transfer is limited which would enable a longer lithium metal battery life cycle. When performing these modifications and testing their electrochemical performance, a current reduction was observed when the electrodes were spontaneously coated with preformed SEI. Herein several classes of artificial SEI layers are explored for their ability to form passivating layers through use of a redox active molecule.

25 ENERGY STORAGE↗

AOI [1]: Passive Wireless Sensor Systems Fabricated by Direct-Writing for Temperature and Health Monitoring of Energy Systems in Harsh-Environments (Final Report)

Researchers at West Virginia University (WVU) propose to demonstrate a wireless, high-temperature sensor system for monitoring the temperature and health of energy-system components. The active sensor and electronics for wireless communication will be composed entirely of an electroceramic materials (conductive ceramics) which are capable of withstanding the harsh-environments required for fossil energy-based technologies. This work will focus primarily on the fabrication and testing of temperature (thermocouples and thermistors) and health (strain/stress and crack propagation sensors) that function at extreme temperatures (up to 700-1700ºC). The electronics will accompany the high-temperature sensor, which will include a passive wireless communication circuit that allows the transmission of the data based on the LCR resonance principle to a near-by reader antenna. This passive transmission of data will reduce the need for interconnect wires near the active, and possibly rotating, energy-system component. The research will include process development to permit the 2D/3D direct-writing of the entire sensor and communication circuit onto the energy-system component. The direct-writing will be facilitated by using silicon-based polymer-derived precursors to form the high-temperature, stable electroceramic compositions. In addition, methods for direct-writing the circuit onto a fugitive carrier substrate will be completed, which will permit a “peel-and-stick”-like transfer of the sensor circuit to the energy-system component. This feature will allow the economical and precise placement of the sensor circuit onto components of various shapes and locations, without altering the geometry and active features of the manufactured component, or the removal (or decommissioning) of the component for installation. The proposed work will be directed at the following areas: 1) Investigation of phase formation, sintering/grain growth, and electrical properties of polymer-derived electroceramic composites; 2) Definition of processes to direct-write through ink-jet and robo-casting the polymer-derived electroceramic composites onto oxide and polymer surfaces; 3) Development of methods to form monolithic "peel-and-stick" preforms that will efficiently transfer the sensor circuit to ceramic surfaces after thermal treatment; 4) Design of passive wireless LCR circuits and receiver (reader) antennas for communication and testing at high temperatures; 5) Investigation of the passive wireless sensor system developed (and method of transferring sensor system) for temperature and stress/strain measurements on a SOFC repeat unit and a singular gas turbine blade prototype as example applications.

01 COAL, LIGNITE, AND PEAT↗

Crosslinked Anionic Exchange Membranes (Spring Quarter Report)

With ever growing climate concerns, studying and optimizing hydrogen gas electrolyzers and fuel cells are of high importance. Polymeric anionic exchange membranes (AEM) are attractive replacements to the industry standard proton exchange membranes (PEM) due to their lack of precious metal catalysts and acidic conditions. However, AEMs on the market have yet to preform comparatively to PEMs. To bring AEMs to a competitive level, crosslinking chemistry within the polymer membranes is being investigated to enhance mechanical properties and performance. For this quarter, electrochemical systems, important AEM properties and considerations, and some characterization methods will be reviewed.

08 HYDROGEN↗

ETF Grout Expansion: Effects of Different Slags and Struvite Precipitation Protocols (Stirring Time)

The ETF ammonia tolerant grout waste form was developed by the Vitreous State Laboratory (VSL) to stabilize ammonium and thereby prevent emission of ammonia vapor during solidification of an ammonium-rich, concentrated sodium sulfate aqueous waste stream generated at the Hanford Effluent Treatment Facility (ETF). VSL personnel did not observe expansion in samples prepared during the waste form development work. However, Savannah River National Laboratory (SRNL) personnel detected expansion, in a few ETF grout samples, up to ~ 20 percent vertical expansion, while preforming work scope to evaluate the effect of ETF brine compositional ranges on the precipitation and solidification processes. The initial work requests can be found in Washington River Protection Services (WRPS) Statement of Work (SOW, Requisitions #: 339922 Revisions 0 and 1, March 11, 2021, and November 2021, respectively. As a result of the waste form expansion observed by SRNL, additional evaluation was requested by WRPS SOW Requisitions #: 356730 Revision 0 and Revision 1, February 1, 2022, and July 11, 2022, respectively. The goal of these requests was to determine whether differences in the slags and / or in sample preparation protocols used by VSL and SRNL were the cause of the expansion observed in the SRNL samples. G. Chen, WRPS, arranged a materials exchange between VSL and SRNL and coordinated the VSL protocol(s) for grouting and curing 1L batches of Base Case ETF base case simulant. Materials were exchanged between VSL and SRNL. Both laboratories performed the VSL struvite precipitation-solidification protocol and cured samples for at least 28 days. Differences in VSL and SRNL slag compositions, mineralogy and particle size results in themselves or combined were determined to not be the cause of the expansion because all samples expanded regardless of whether the VSL or SRNL slags were used. The fundamental cause of the observed expansion could not be attributed to minor variations in the following: 1) chemistry of the slag and other reagents, 2) container wall thickness, 3) ambient bench top curing conditions at VSL and SRNL, 4) pH adjustments to 7 ± a few tenths of unit, nor 5) stirring time between the precipitation and solidification process steps. Additional observations include: grout samples prepared with VSL slag expanded less than those prepared with the SRNL slag and, based on a very limited sample set, some samples stirred for longer times expanded less than those stirred for 20 minutes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Chemical durability assessment of enhanced low-activity waste glasses through EPA method 1313

In this work, we report the progress of the Glass Leaching Assessment for Durability (GLAD) program on the implementation of the United States Environmental Protection Agency (EPA) Leaching Environmental Assessment Framework pH-dependent leach test (EPA Method 1313) to low-activity nuclear waste (LAW) glasses. The GLAD program seeks to develop new strategies to understand the chemical durability of nuclear waste glasses for the disposal in near-surface conditions. A series of 16 high-waste loading LAW glasses, currently under development, were selected using machine learning methods to study the corrosion behavior using EPA Method 1313. Reacted glass powders were examined using scanning electron microscopy and the eluate compositions were examined using inductively coupled plasma-optical emission spectroscopy. Compositional modeling was used to fit the measured elemental releases from EPA Method 1313. The compositional models demonstrated that elements such as Si reduce elemental release while B can increase elemental release (consistent with elemental modeling of the Product Consistency Test and Vapor Hydration Test) while other elements, such as Fe, exhibit pH-dependent behavior. The amount of acid added during the EPA testing was found to significantly impact the observed result, which was only apparent after preforming the present matrix study. The overall titration curves were able to be compositionally modeled for future process optimization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

ETF Grout Expansion: Evaluation of MgO Additions and Struvite Precipitation Protocol for Potential Expansion

The ETF ammonia tolerant grout waste form was developed by the Vitreous State Laboratory (VSL) to stabilize ammonium and thereby prevent emission of ammonia vapor during solidification of an ammonium-rich, concentrated sulfate aqueous waste stream generated at the Hanford Effluent Treatment Facility (ETF). VSL did not observe expansion in samples prepared during the waste form development work. However, Savannah River National Laboratory (SRNL) personnel did encounter expansion, in some cases up to 20+ volume percent expansion in ETF grout samples while preforming work scope to evaluate compositional ranges for ETF brine and of the precipitation and solidification reagent. The work requests can be found in Washington River Protection Services (WRPS) Statement of Work (SOW), Requisitions #: 339922 Revisions 0 and 1, March 11, 2021, and November 2021. Additional evaluation was requested by WRPS SOW Requisitions #: 356730, Revision 1, February 1, 2022, to determine whether differences in the slags or differences in sample preparation protocols used by VSL and SRNL were the cause of the expansion observed in the SRNL samples. G. Chen, WRPS, arranged a materials exchange between VSL and SRNL and coordinated the VSL protocol for grouting and curing 1L of Base Case ETF simulant. Materials were exchanged between VSL and SRNL and both laboratories performed the VSL struvite precipitation-solidification protocol and cured samples for at least 28 days. VSL and SRNL encountered expansion, at varying degrees, in all samples prepared under the material exchange and grouting protocol. Additional material exchange testing between VSL and SRNL and alternative materials evaluation to further investigate the causes of grout expansion and differentiate the effects of various dry materials, grouting procedures, and curing containers was requested by WRPS SOW Requisitions #: 356730, Revision 2, January 10, 2023. Pacific Northwest National Laboratory (PNNL) assembled and distributed materials to both laboratories for testing. Observations from this study indicated variations in MgO additions, water-to-dry mix (dm) ratios and curing containers did not correlate to ETF ammonia grout expansion. In comparison to previous work, SRNL observed the addition rate of NaOH to be a potential factor for the final pH in the struvite precipitation step. In the current testing NaOH was added in bulk (5-10 mL at one time) during the precipitation step. The resulting pH was 7.57-9.15 which is slightly higher than pH observed at a slower addition rate. Additional testing is needed to identify the presence and/or struvite stability in high-pH struvite precipitant ETF ammonia grout samples. Therefore, based on current data, it is unknown if NaOH addition rate is the fundamental cause of grout expansion.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

CINDER90 and CINDER2008 Comparison for Second Target Station Analysis

A preliminary target activation analysis for the Second Target Station (STS) at the Spallation Neutron Source (SNS) located at Oak Ridge National Laboratory (ORNL) was preformed using Monte Carlo N-Particle X (MCNPX), CINDER90, and the corresponding multi-group cross section libraries distributed with CINDER90. This preliminary analysis has been used to guide some design decisions of the STS target design. Using the MCNPX output files from this preliminary analysis, a comparison of the activation analysis using CINDER90 and CINDER2008 was performed. While the CINDER90 code has been validated for use in spallation source activation and transmutation calculations, and compares well with measurements, the transition to the modernized version of the code (CINDER2008) and the updated cross section libraries is desirable. The goal of this comparison is to evaluate the differences and implications for the STS activation analysis. Overall, the total activity differs between CINDER2008 and CINDER90 by no more than 20% for the materials evaluated in this report. The largest discrepancies were observed in the decay gamma intensity densities with CINDER90 calculating a factor of 2 higher than CINDER2008.

97 MATHEMATICS AND COMPUTING↗

Economic Impact of Closing the Nuclear Fuel Cycle

This report estimates the economic impact of closing the United States nuclear fuel cycle. Several different fuel cycle scenarios are analyzed. These scenarios include a baseline analysis of the existing fuel cycle conditions, a hypothetical scenario where all fuel cycle operations are preformed domestically, a scenario where all reactors are replaced with sodium fast reactors, and finally a scenario that uses a mix of fast reactors and light water reactors operating on mixed oxide fuel. Each scenario modeled is assumed to be operating at equilibrium and producing electricity at a 100 GWe-yr capacity. Impacts are calculated for normal operations and do not include construction or infrastructure expansion impacts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermally Insulating Transparent Barrier (THINNER) coatings on single pane windows

Conventional silica aerogel monoliths can provide remarkable thermal insulation but the presence of large pores (> 30 nm) tends to scatter visible light and render the material opaque or translucent instead of transparent. In addition, they are prone to cracking during synthesis and handling which makes them difficult to integrate in products and in particular in window solutions. This project developed two new solgel synthesis methods using silica precursors or preformed silica nanoparticles and ambient drying to produce mesoporous organo-silica monoliths. The monoliths were (i) thermally insulating, (ii) optically transparent, (iii) flexible, and (iv) hydrophobic. They feature porosity ranging from 50% to 90% with narrow pore size distribution with pore less than 20 nm resulting in excellent optical clarity (haze < 2%) and very low thermal conductivity (< 30 mW/mK). Interestingly, not only porosity but also pore size and mass fractal dimension were found to affect the thermal conductivity of the mesoporous silica. The superior transparency of the monoliths was shown to be attributed to dependent scattering among silica nanoparticles. Flexibility was achieved through trimethylchlorosilane surface modification. Furthermore, process scale-up and integration of the ambigel monoliths into window solutions using optically clear adhesives were also demonstrated in 6”x6” double-pane windows. The aerogel and the window solution were shown to be durable to accelerated aging under UV, moisture, and/or temperature gradient and thermal cycling. Overall, the window solution achieved the technical performance and the cost target of $10/sqft set for the SHIELD program. However, scaling to industry relevant scale (> 10’x10’) remains a challenge due to requirements on the drying process and fume hood size and to the propensity of large aerogel slab to crack during drying.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) Tutorial

The Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) refers to a set of computer programs that were developed to create and analyze probabilistic risk assessment (PRAs). This volume is the tutorial manual for the SAPHIRE system. In this document, a series of lessons are provided that guide the user through basic steps common to most analyses preformed with SAPHIRE. The tutorial is divided into two major sections covering both basic and advanced features. The section covering basic topics contains lessons that lead the reader through development of a probabilistic hypothetical problem involving a vehicle accident, highlighting the program’s most fundamental features. The advanced features section contains additional lessons that expand on fundamental analysis features of SAPHIRE and provide insights into more complex analysis techniques. Together, these two elements provide an overview into the operation and capabilities of the SAPHIRE software.

99 GENERAL AND MISCELLANEOUS↗

SILICON CARBIDE CERAMICS FOR COMPACT HEAT EXCHANGERS

Silicon carbide (SiC) materials are prime candidates for high temperature heat exchangers for next generation nuclear reactors due to their refractory nature and high thermal conductivity at elevated temperatures. This research has focused on demonstrating the potential of liquid silicon infiltration (LSI) for making SiC to achieve this goal. The major advantage of this method over other ceramic processing techniques is the enhanced capability of making high dense, high purity SiC materials in complex net shapes. For successful formation of net shape SiC using LSI techniques, the carbon preform reactivity and pore structure must be controlled to allow the complete infiltration of the porous carbon structure which allows complete conversion of the carbon to SiC. We have established a procedure for achieving desirable carbon properties by using carbon precursors consisting of two readily available high purity organic materials, crystalline cellulose and phenolic resin. Phenolic resin yields a glassy carbon with low chemical reactivity and porosity while the cellulose carbon is highly reactive and porous. By adjusting the ratio of these two materials in the precursor mixtures, the properties of the carbons produced can be controlled. We have identified the most favorable carbon precursor composition to be a cellulose resin mass ratio of 6:4 for LSI formation of SiC. The optimum reaction conditions are a temperature of 1800 C, a pressure of 0.5 Torr of argon, and a time of 120 minutes. The fully dense net shape SiC material produced has a density of 2.96 g cm{sup -3} (about 92% of pure SiC) and a SiC volume fraction of over 0.82. Kinetics of the LSI SiC formation process was studied by optical microscopy and quantitative digital image analysis. This study identified six reaction stages and provided important understanding of the process. Although the thermal conductivity of pure SiC at elevated temperatures is very high, thermal conductivities of most commercial SiC materials are much lower due to phonon scattering by impurities (e.g., sintering aids located at the grain boundaries of these materials). The thermal conductivity of our SiC was determined using the laser flash method and it is 214 W/mK at 373 K and 64 W/mK at 1273 K. These values are very close to those of pure SiC and are much higher than those of SiC materials made by industrial processes. This SiC made by our LSI process meets the thermal properties required for use in high temperature heat exchanger. Cellulose and phenolic resin carbons lack the well-defined atomic structures associated with common carbon allotropes. Atomic-scale structure was studied using high resolution transmission electron microscopy (HRTEM), nitrogen gas adsorption and helium gas pycnometry. These studies revealed that cellulose carbon exhibits a very high degree of atomic disorder and angstrom-scale porosity. It has a density of only 93% of that of pure graphite, with primarily sp2 bonding character and a low concentration of graphene clusters. Phenolic resin carbon shows more structural order and substantially less angstrom-scale porosity. Its density is 98% of that of pure graphite, and Fourier transform analysis of its TEM micrographs has revealed high concentrations of sp3 diamond and sp2 graphene nano-clusters. This is the first time that diamond nano-clusters have been observed in carbons produced from phenolic resin. AC and DC electrical measurements were made to follow the thermal conversion of microcrystalline cellulose to carbon. This study identifies five regions of electrical conductivity that can be directly correlated to the chemical decomposition and microstructural evolution during carbonization. In Region I, a decrease in overall AC conductivity occurs due to the initial loss of the polar groups from cellulose molecules. In Region II, the AC conductivity starts to increase with heat treatment temperature due to the formation and growth of conducting carbon clusters. In Region III, a further increase of AC conductivity with increasing heat treatment temperature is observed. In addition, the AC conductivity demonstrates a non-linear frequency dependency due to electron hopping, interfacial polarization, and onset of a percolation threshold. In Region IV, the DC conductivity continues to increase with heat treatment due to the growth and percolation of carbon clusters. Finally in Region V, the DC conductivity reaches a plateau with increasing heat treatment temperature as the system reaches a fully percolated state. Thermophysical properties of carbon materials derived from microcrystalline cellulose have been measured under vacuum and compared with earlier measurements conducted under nitrogen to better understand the influence of porosity, composition, and atmosphere effects. The effective thermal conductivity in vacuum is lower than that observed in nitrogen primarily due to the conductivity of nitrogen gas.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Spin-forming Project Report

In a second development order, spin-forming equipment was again evaluated using the test shape, a hemispherical shell. In this second development order, pure vanadium and alloy titanium (Ti-6Al-4V) were spin-formed, as well as additional copper and 21-6-9 stainless. In the first development order the following materials had been spin-formed: copper (alloy C11000 ETP), 6061 aluminum, 304L stainless steel, 21-6-9 stainless steel, and tantalum-2.5% tungsten. Significant challenges included properly adjusting the rotations-per-minute (RPM), cracking at un-beveled edges and laser marks, redressing of notches, surface cracking, non-uniform temperature evolution in the titanium, and cracking of the tailstock. Lessons learned were that 300 RPM worked better than 600 RPM for most materials (at the feed rate of 800 mm/min); beveling the edges to lower the stress reduces edge cracking; notches, laser marks, or edge defects in the preform doom the process to cracking and failure; coolant is required for vanadium spin-forming; increasing the number of passes to nine or more eliminates surface cracking for vanadium; titanium develops a hot zone in front of the rollers; and the tailstock should be redesigned to eliminate the cylindrical stress concentrator in the center.

36 MATERIALS SCIENCE↗