Search NASA⌕ Search

SEARCH · Search NASA

Results for “reduced set methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Hierarchical Particle Mesh: An FFT-accelerated Fast Multipole Method

I observe a modification to the original Fast Multipole Method (FMM) of Greengard & Rokhlin that approximates the gravitation field of an FMM cell as a small uniform grid (a “gridlet”) of effective masses. The effective masses on a gridlet are set from the requirement that the multipole moments of the FMM cells are reproduced exactly, thus preserving the accuracy of the gravitational field representation. The measurement of the gravitational field from a multipole expansion can then be computed for all multipole orders simultaneously, with a single Fast Fourier Transform, significantly reducing the computational cost at a given value of the required accuracy. The described approach belongs to the class of “kernel independent” variants of the FMM method and works with any Green function.

79 ASTRONOMY AND ASTROPHYSICS↗

Three-dimensional phase field sintering simulations accounting for the rigid-body motion of individual grains

Sintering is a widely used powder processing technique in industrial applications. During sintering, atoms migrate to decrease the energy of the system via two main mechanisms: coarsening and densification, both of which lead to significant morphological variation of the sintered microstructure. When simulating sintering dynamics, the phase-field method has been broadly utilized because of its convenience in tracking morphology evolution. When a large number of grains is involved, it is common to use the same order parameter to describe multiple grains that are not in direct contact with one another (in order to reduce the computational memory demands). However, with this treatment it is difficult to handle the rigid-body motion of individual grains during densification. In this work, an implementation scheme is introduced to overcome the challenge of calculating individual particle motion based on existing equations. It uses a grouping algorithm and sets a cutoff radius on each grain for calculating the particle velocity during densification. This method allows for the incorporation of the densification mechanism, which has been commonly ignored in previous work, into phase-field sintering models in three-dimensional simulations with a large number of particles/grains. Moreover, through combination with the smoothed boundary method, material properties of sintered microstructures, such as the effective diffusivity and Young’s modulus, can be calculated during the sintering processes.

36 MATERIALS SCIENCE↗

Evaluation of the excitation spectra with diffusion Monte Carlo on an auxiliary bosonic ground state

We aim to improve upon the variational Monte Carlo (VMC) approach for excitations replacing the Jastrow factor by an auxiliary bosonic (AB) ground state and multiplying it by a fermionic component factor. The instantaneous change in imaginary time of an arbitrary excitation in the original interacting fermionic system is obtained by measuring observables via the ground-state distribution of walkers of an AB system that is subject to an auxiliary effective potential. The effective potential is used to (i) drive the AB system’s ground-state configuration space toward the configuration space of the excitations of the original fermionic system and (ii) subtract from a diffusion Monte Carlo (DMC) calculation contributions that can be included in conventional approximations, such as mean-field and configuration interaction (CI) methods. In this novel approach, the AB ground state is treated statistically in DMC, whereas the fermionic component of the original system is expanded in a basis. The excitation energies of the fermionic eigenstates are obtained by sampling a fermion–boson coupling term on the AB ground state. We show that this approach can take advantage of and correct for approximate eigenstates obtained via mean-field calculations or truncated interactions. We demonstrate that the AB ground-state factor incorporates the correlations missed by standard Jastrow factors, further reducing basis truncation errors. Relevant parts of the theory have been tested in soluble model systems and exhibit excellent agreement with exact analytical data and CI and VMC approaches. In particular, for limited basis set expansions and sufficient statistics, AB approaches outperform CI and VMC in terms of basis size for the same systems. The implementation of this method in current codes, despite being demanding, will be facilitated by reusing procedures already developed for calculating ground-state properties with DMC and excitations with VMC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physics-informed latent neural operator for real-time predictions of time-dependent parametric PDEs

Deep operator network (DeepONet) has shown significant promise as surrogate models for systems governed by partial differential equations (PDEs), enabling accurate mappings between infinite-dimensional function spaces. However, when applied to systems with high-dimensional input-output mappings arising from large numbers of spatial and temporal collocation points, these models often require heavily overparameterized networks, leading to long training times. Latent DeepONet addresses some of these challenges by introducing a two-step approach: first learning a reduced latent space using a separate model, followed by operator learning within this latent space. While efficient, this method is inherently data-driven and lacks mechanisms for incorporating physical laws, limiting its robustness and generalizability in data-scarce settings. Here, in this work, we propose PI-Latent-NO, a physics-informed latent neural operator framework that integrates governing physics directly into the learning process. Our architecture features two coupled DeepONets trained end-to-end: a Latent-DeepONet that learns a low-dimensional representation of the solution, and a Reconstruction-DeepONet that maps this latent representation back to the physical space. By embedding PDE constraints into the training via automatic differentiation, our method eliminates the need for labeled training data and ensures physics-consistent predictions. The proposed framework is both memory and compute-efficient, exhibiting near-constant scaling with problem size and demonstrating significant speedups over traditional physics-informed operator models. We validate our approach on a range of parametric PDEs, showcasing its accuracy, scalability, and suitability for real-time prediction in complex physical systems.

Latent representations↗

How much improvement in thermoelectric performance can come from reducing thermal conductivity?

Large improvements in the performance of thermoelectric materials have come from designing materials with reduced thermal conductivity. Yet as the thermal conductivity of some materials now approaches their amorphous limit, it is unclear if microstructure engineering can further improve thermoelectric performance in these cases. In this contribution, we use large data sets to examine 300 compositions in 11 families of thermoelectric materials and present a type of plot that quickly reveals the maximum possible zT that can be achieved by reducing the thermal conductivity. This plot allows researchers to quickly distinguish materials where the thermal conductivity has been optimized from those where improvement can be made. Moreover, through these large data sets we examine structure-property relationships to identify methods that decrease thermal conductivity and improve thermoelectric performance. We validate, with the data, that increasing (i) the volume of a unit cell and/or (ii) the number of atoms in the unit cell decreases the thermal conductivity of many classes of materials, without changing the electrical resistivity.

36 MATERIALS SCIENCE↗

Correction of quantification errors in pelvic and spinal lesions caused by ignoring higher photon attenuation of bone in [{sup 18}F]NaF PET/MR

Purpose: MR-based attenuation correction (MRAC) in routine clinical whole-body positron emission tomography and magnetic resonance imaging (PET/MRI) is based on tissue type segmentation. Due to lack of MR signal in cortical bone and the varying signal of spongeous bone, standard whole-body segmentation-based MRAC ignores the higher attenuation of bone compared to the one of soft tissue (MRAC{sub nobone}). The authors aim to quantify and reduce the bias introduced by MRAC{sub nobone} in the standard uptake value (SUV) of spinal and pelvic lesions in 20 PET/MRI examinations with [{sup 18}F]NaF. Methods: The authors reconstructed 20 PET/MR [{sup 18}F]NaF patient data sets acquired with a Philips Ingenuity TF PET/MRI. The PET raw data were reconstructed with two different attenuation images. First, the authors used the vendor-provided MRAC algorithm that ignores the higher attenuation of bone to reconstruct PET{sub nobone}. Second, the authors used a threshold-based algorithm developed in their group to automatically segment bone structures in the [{sup 18}F]NaF PET images. Subsequently, an attenuation coefficient of 0.11 cm{sup −1} was assigned to the segmented bone regions in the MRI-based attenuation image (MRAC{sub bone}) which was used to reconstruct PET{sub bone}. The automatic bone segmentation algorithm was validated in six PET/CT [{sup 18}F]NaF examinations. Relative SUV{sub mean} and SUV{sub max} differences between PET{sub bone} and PET{sub nobone} of 8 pelvic and 41 spinal lesions, and of other regions such as lung, liver, and bladder, were calculated. By varying the assigned bone attenuation coefficient from 0.11 to 0.13 cm{sup −1}, the authors investigated its influence on the reconstructed SUVs of the lesions. Results: The comparison of [{sup 18}F]NaF-based and CT-based bone segmentation in the six PET/CT patients showed a Dice similarity of 0.7 with a true positive rate of 0.72 and a false discovery rate of 0.33. The [{sup 18}F]NaF-based bone segmentation worked well in the pelvis and spine. However, it showed artifacts in the skull and in the extremities. The analysis of the 20 [{sup 18}F]NaF PET/MRI examinations revealed relative SUV{sub max} differences between PET{sub nobone} and PET{sub bone} of (−8.8% ± 2.7%, p = 0.01) and (−8.1% ± 1.9%, p = 2.4 × 10{sup −8}) in pelvic and spinal lesions, respectively. A maximum SUV{sub max} underestimation of −13.7% was found in lesion in the third cervical spine. The averaged SUV{sub mean} differences in volumes of interests in lung, liver, and bladder were below 3%. The average SUV{sub max} differences in pelvic and spinal lesions increased from −9% to −18% and −8% to −17%, respectively, when increasing the assigned bone attenuation coefficient from 0.11 to 0.13 cm{sup −1}. Conclusions: The developed automatic [{sup 18}F]NaF PET-based bone segmentation allows to include higher bone attenuation in whole-body MRAC and thus improves quantification accuracy for pelvic and spinal lesions in [{sup 18}F]NaF PET/MRI examinations. In nonbone structures (e.g., lung, liver, and bladder), MRAC{sub nobone} yields clinically acceptable accuracy.

60 APPLIED LIFE SCIENCES↗

Validation of a wall-interference assessment/correction procedure for airfoil tests in the Langley 0.3-meter Transonic Cryogenic Tunnel

Validation of a wall-interference assessment/correction (WIAC) procedure for a given facility requires its application to several sets of test data. It is necessary therefore to create a somewhat automated method for processing data through the various steps in the procedure. An automated procedure is also welcomed by the test engineer or eventual user in order to reduce the required effort and opportunity for error. Such a procedure has been developed for the Langley 0.3-m Transonic Cryogenic Tunnel using the TWINTN4 WIAC code. This code provides a four-wall, 2-D, transonic correction; that is, it accounts for sidewall boundary-layer effects, as well as for top and bottom wall effects on the airfoil tests. The TWINTN4 code utilizes measured pressure data at the tunnel walls and on the airfoil model; thus, classical homogeneous-wall boundary conditions are not used in the correction procedure.

Gumbert, C. R.↗

Estimating Reduced Consumption for Dynamic Demand Response

Growing demand is straining our existing electricity generation facilities and requires active participation of the utility and the consumers to achieve energy sustainability. One of the most effective and widely used ways to achieve this goal in the smart grid is demand response (DR), whereby consumers reduce their electricity consumption in response to a request sent from the utility whenever it anticipates a peak in demand. To successfully plan and implement demand response, the utility requires reliable estimate of reduced consumption during DR. This also helps in optimal selection of consumers and curtailment strategies during DR. While much work has been done on predicting normal consumption, reduced consumption prediction is an open problem that is under-studied. In this paper, we introduce and formalize the problem of reduced consumption prediction, and discuss the challenges associated with it. We also describe computational methods that use historical DR data as well as pre-DR conditions to make such predictions. Our experiments are conducted in the real-world setting of a university campus microgrid, and our preliminary results set the foundation for more detailed modeling.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

A HUBBLE DIAGRAM FROM TYPE II SUPERNOVAE BASED SOLELY ON PHOTOMETRY: THE PHOTOMETRIC COLOR METHOD

We present a Hubble diagram of SNe II using corrected magnitudes derived only from photometry, with no input of spectral information. We use a data set from the Carnegie Supernovae Project I for which optical and near-infrared light curves were obtained. The apparent magnitude is corrected by two observables, one corresponding to the slope of the plateau in the V band and the second a color term. We obtain a dispersion of 0.44 mag using a combination of the (V − i) color and the r band and we are able to reduce the dispersion to 0.39 mag using our golden sample. A comparison of our photometric color method (PCM) with the standardized candle method (SCM) is also performed. The dispersion obtained for the SCM (which uses both photometric and spectroscopic information) is 0.29 mag, which compares with 0.43 mag from the PCM for the same SN sample. The construction of a photometric Hubble diagram is of high importance in the coming era of large photometric wide-field surveys, which will increase the detection rate of supernovae by orders of magnitude. Such numbers will prohibit spectroscopic follow up in the vast majority of cases, and hence methods must be deployed which can proceed using solely photometric data.

79 ASTRONOMY AND ASTROPHYSICS↗

Dislocation model of nucleation and development of slip bands and their effect on service life of structural materials subject to cyclic loading

Most of the destructions of machine parts are of fatigue character. Under cyclic loading, the surface layer, in which hardening–softening processes rapidly occur, is formed almost at once after its beginning. The interaction of plastic-deformation traces with each other and with other structural elements, such as grains, results in the formation of a characteristic microstructure of the machine-part surface subject to cyclic loadings. The character of accumulation of slip bands and their shape (narrow, wide, twisting, and broken) depends on the conditions under which (under what factors) the cyclic loading occurs. The fatigue-resistance index expressed in terms of the slope of left portion of the fatigue curve linearized in logarithmic coordinates also depends on the set of relevant factors. The dependence of the surface damageability on the fatigue resistance index makes it possible to implement the method of predicting the fatigue curve by the description of the factors acting on a detail or construction. The position of the inflection point on the curve in the highcycle fatigue region (the endurance limit and the number of loading cycles, the ordinate and abscissa of the inflection point on the fatigue curve, respectively) also depends on the set of relevant factors. In combination with the previously obtained value of the slope of the left portion of the curve in the high-cycle fatigue region, this makes it possible to construct an a priori fatigue curve, thus reducing the scope of required fatigue tests and, hence, high expenses because of their long duration and high cost. The scope of tests upon using the developed method of prediction may be reduced to a minimum of one or two samples at the predicted level of the endurance limit.

36 MATERIALS SCIENCE↗

Diagnosing and Correcting Mass Accuracy and Signal Intensity Error Due to Initial Ion Position Variations in a MALDI TOFMS

Frustrated by worse than expected error for both peak area and time-of-flight (TOF) in matrix assisted laser desorption ionization (MALDI) experiments using samples prepared by electrospray deposition, it was finally determined that there was a correlation between sample location on the target plate and the measured TOF/peak area. Variations in both TOF and peak area were found to be due to small differences in the initial position of ions formed in the source region of the TOF mass spectrometer. These differences arise largely from misalignment of the instrument sample stage, with a smaller contribution arising from the non-ideal shape of the target plates used. By physically measuring the target plates used and comparing TOF data collected from three different instruments, an estimate of the magnitude and direction of the sample stage misalignment was determined for each of the instruments. A correction method was developed to correct the TOFs and peak areas obtained for a given combination of target plate and instrument. Two correction factors are determined, one by initially collecting spectra from each sample position used and another by using spectra from a single position for each set of samples on a target plate. For TOF and mass values, use of the correction factor reduced the error by a factor of 4, with the relative standard deviation (RSD) of the corrected masses being reduced to 12-24 ppm. For the peak areas, the RSD was reduced from 28% to 16% for samples deposited twice onto two target plates over two days. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Improving superficial target delineation in radiation therapy with endoscopic tracking and registration

Purpose: Target delineation within volumetric imaging is a critical step in the planning process of intensity modulated radiation therapy. In endoluminal cancers, endoscopy often reveals superficial areas of visible disease beyond what is seen on volumetric imaging. Quantitatively relating these findings to the volumetric imaging is prone to human error during the recall and contouring of the target. We have developed a method to improve target delineation in the radiation therapy planning process by quantitatively registering endoscopic findings contours traced on endoscopic images to volumetric imaging. Methods: Using electromagnetic sensors embedded in an endoscope, 2D endoscopic images were registered to computed tomography (CT) volumetric images by tracking the position and orientation of the endoscope relative to a CT image set. Regions-of-interest (ROI) in the 2D endoscopic view were delineated. A mesh created within the boundary of the ROI was projected onto the 3D image data, registering the ROI with the volumetric image. This 3D ROI was exported to clinical radiation treatment planning software. The precision and accuracy of the procedure was tested on two solid phantoms with superficial markings visible on both endoscopy and CT images. The first phantom was T-shaped tube with X-marks etched on the interior. The second phantom was an anatomically correct skull phantom with a phantom superficial lesion placed on the pharyngeal surface. Markings were contoured on the endoscope images and compared with contours delineated in the treatment planning system based on the CT images. Clinical feasibility was tested on three patients with early stage glottic cancer. Image-based rendering using manually identified landmarks was used to improve the registration. Results: Using the T-shaped phantom with X-markings, the 2D to 3D registration accuracy was 1.5-3.5 mm, depending on the endoscope position relative to the markings. Intraobserver standard variation was 0.5 mm. Rotational accuracy was within 2 deg. Using the skull phantom, registration accuracy was assessed by calculating the average surface minimum distance between the endoscopy and treatment planning contours. The average surface distance was 0.92 mm with 93% of all points in the 2D-endoscopy ROI within 1.5 mm of any point within the ROI contoured in the treatment planning software. This accuracy is limited by the CT imaging resolution and the electromagnetic (EM) sensor accuracy. The clinical testing demonstrated that endoscopic contouring is feasible. With registration based on em tracking only, accuracy was 5.6-8.4 mm. Image-based registration reduced this error to less than 3.5 mm and enabled endoscopic contouring in all cases. Conclusions: Registration of contours generated on 2D endoscopic images to 3D planning space is feasible, with accuracy smaller than typical set-up margins. Used in addition to standard 3D contouring methods in radiation planning, the technology may improve gross tumour volume (GTV) delineation for superficial tumors in luminal sites that are only visible in endoscopy.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Three-dimensional anisotropic adaptive filtering of projection data for noise reduction in cone beam CT

Purpose: The combination of quickly rotating C-arm gantry with digital flat panel has enabled the acquisition of three-dimensional data (3D) in the interventional suite. However, image quality is still somewhat limited since the hardware has not been optimized for CT imaging. Adaptive anisotropic filtering has the ability to improve image quality by reducing the noise level and therewith the radiation dose without introducing noticeable blurring. By applying the filtering prior to 3D reconstruction, noise-induced streak artifacts are reduced as compared to processing in the image domain. Methods: 3D anisotropic adaptive filtering was used to process an ensemble of 2D x-ray views acquired along a circular trajectory around an object. After arranging the input data into a 3D space (2D projections + angle), the orientation of structures was estimated using a set of differently oriented filters. The resulting tensor representation of local orientation was utilized to control the anisotropic filtering. Low-pass filtering is applied only along structures to maintain high spatial frequency components perpendicular to these. The evaluation of the proposed algorithm includes numerical simulations, phantom experiments, and in-vivo data which were acquired using an AXIOM Artis dTA C-arm system (Siemens AG, Healthcare Sector, Forchheim, Germany). Spatial resolution and noise levels were compared with and without adaptive filtering. A human observer study was carried out to evaluate low-contrast detectability. Results: The adaptive anisotropic filtering algorithm was found to significantly improve low-contrast detectability by reducing the noise level by half (reduction of the standard deviation in certain areas from 74 to 30 HU). Virtually no degradation of high contrast spatial resolution was observed in the modulation transfer function (MTF) analysis. Although the algorithm is computationally intensive, hardware acceleration using Nvidia's CUDA Interface provided an 8.9-fold speed-up of the processing (from 1336 to 150 s). Conclusions: Adaptive anisotropic filtering has the potential to substantially improve image quality and/or reduce the radiation dose required for obtaining 3D image data using cone beam CT.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Viability of Additively Manufactured Electrodes for Lithium-Ion Batteries

As the global economy becomes increasingly electrified, the demand for batteries and energy storage is expected to rise significantly, particularly in the transportation and electricity sectors. Lithium-ion batteries (LIBs) are currently the most advanced and widely used technology in this field. Traditionally, LIBs are manufactured using simple 2D planar geometries to maximize production efficiency and minimize costs. However, this approach limits energy density due to the restricted design flexibility of the electrodes. Additive manufacturing (AM) offers a promising solution to enhance the energy density and efficiency of LIBs by enabling the design of architectures that reduce diffusive losses and allow for a greater amount of active material to be incorporated within the same device footprint, thereby minimizing the use of inactive materials. Different AM techniques come with their own set of limitations, including printing speed, material compatibility, and scale, which must be considered when designing electrodes. Scalable and cost-effective methods are particularly important for electric vehicle batteries, while achieving higher energy densities in microbatteries is crucial for the miniaturization of wearable electronics and medical devices. Here, in this study, we simulate various 3D porous electrode designs for LIBs using graphite and nickel manganese cobalt oxide (NMC) electrodes. These designs are selected to represent structures that could be produced using different AM techniques, such as direct ink writing, fused deposition modeling, and stereolithography. Our results indicate that at higher charging rates and increased areal mass loading, 3D structures can outperform traditional 2D electrodes, although the benefits may diminish with more complex designs that are harder to manufacture. The observed gains in energy density are attributed to improved electrode utilization and reduced diffusive energy losses. This comprehensive analysis of structure–performance relationships will provide valuable insights to guide future research on 3D designs, material selection, and AM techniques for additively manufactured battery electrodes.

25 ENERGY STORAGE↗

Neural network denoising of x-ray images from high-energy-density experiments

Noise is a consistent problem for x-ray transmission images of High-Energy-Density (HED) experiments because it can significantly affect the accuracy of inferring quantitative physical properties from these images. We consider experiments that use x-ray area backlighting to image a thin layer of opaque material within a physics package to observe its hydrodynamic evolution. The spatial variance of the x-ray transmission across the system due to changing opacity serves as an analog for measuring density in this evolving layer. The noise in these images adds nonphysical variations in measured intensity, which can significantly reduce the accuracy of our inferred densities, particularly at small spatial scales. Denoising these images is thus necessary to improve our quantitative analysis, but any denoising method also affects the underlying information in the image. In this paper, we present a method for denoising HED x-ray images via a deep convolutional neural network model with a modified DenseNet architecture. In our denoising framework, we estimate the noise present in the real (data) images of interest and apply the inferred noise distribution to a set of natural images. These synthetic noisy images are then used to train a neural network model to recognize and remove noise of that character. We show that our trained denoiser network significantly reduces the noise in our experimental images while retaining important physical features.

47 OTHER INSTRUMENTATION↗

Symmetry reduction of quasi-free states

Given a group-invariant quasi-free state on the algebra of canonical commutation relations (CCR), we show how group averaging techniques can be used to obtain a symmetry-reduced CCR algebra and reduced quasi-free state. When the group is compact, this method of symmetry reduction leads to standard results which can be obtained using other methods. When the group is noncompact, the group averaging prescription relies on technically favorable conditions which we delineate. As an example, we consider symmetry reduction of the usual vacuum state for a Klein-Gordon field on Minkowski spacetime by a noncompact subgroup of the Poincare group consisting of a 1-parameter family of boosts, a 1-parameter family of spatial translations and a set of discrete translations. We show that the symmetry-reduced CCR algebra and vacuum state correspond to that used by each of Berger, Husain, and Pierri for the polarized Gowdy T{sup 3} quantum gravity model.

97 MATHEMATICS AND COMPUTING↗

A trust-region algorithm for the optimization of PSA processes using reduced-order modeling

The last few decades have seen a considerable increase in the applications of adsorptive gas separation technologies, such as pressure swing adsorption (PSA); the applications range from bulk separations to trace contaminant removal. PSA processes are based on solid-gas equilibrium and operate under periodic transient conditions [1]. Bed models for these processes are therefore defined by coupled nonlinear partial differential and algebraic equations (PDAEs) distributed in space and time with periodic boundary conditions that connect the processing steps together and high nonlinearities arising from non-isothermal effects and nonlinear adsorption isotherms. As a result, the optimization of such systems for either design or operation represents a significant computational challenge to current nonlinear programming algorithms. Model reduction is a powerful methodology that permits systematic generation of cost-efficient low-order representations of large-scale systems that result from discretization of such PDAEs. In particular, low-dimensional approximations can be obtained from reduced order modeling (ROM) techniques based on proper orthogonal decomposition (POD) and can be used as surrogate models in the optimization problems. In this approach, a representative ensemble of solutions of the dynamic PDAE system is constructed by solving a higher-order discretization of the model using the method of lines, followed by the application of Karhunen-Loeve expansion to derive a small set of empirical eigenfunctions (POD modes). These modes are used as basis functions within a Galerkin's projection framework to derive a low-order DAE system that accurately describes the dominant dynamics of the PDAE system. This approach leads to a DAE system of significantly lower order, thus replacing the one obtained from spatial discretization before and making optimization problem computationally efficient [2]. The ROM methodology has been successfully applied to a 2-bed 4-step PSA process used for separating a hydrogen-methane mixture in [3]. The reduced order model developed was successfully used to optimize this process to maximize hydrogen recovery within a trust-region. We extend this approach in this work to develop a rigorous trust-region algorithm for ROM-based optimization of PSA processes. The trust-region update rules and sufficient decrease condition for the objective is used to determine the size of the trust-region. Based on the decrease in the objective function and error in the ROM, a ROM updation strategy is designed [4, 5]. The inequalities and bounds are handled in the algorithm using exact penalty formulation, and a non-smooth trust-region algorithm by Conn et al. [6] is used to handle non-differentiability. To ensure that the first order consistency condition is met and the optimum obtained from ROM-based optimization corresponds to the optimum of the original problem, a scaling function, such as one proposed by Alexandrov et al. [7], is incorporated in the objective function. Such error control mechanism is also capable of handling numerical inconsistencies such as unphysical oscillations in the state variable profiles. The proposed methodology is applied to optimize a PSA process to concentrate CO{sub 2} from a nitrogen-carbon dioxide mixture. As in [3], separate ROMs are developed for each operating step with different POD modes for each state variable. Numerical results will be presented for optimization case studies which involve maximizing CO{sub 2} recovery, feed throughput or minimizing overall power consumption.

97 MATHEMATICS AND COMPUTING↗

A Sparse-Grid Probabilistic Scheme for Approximation of the Runaway Probability of Electrons in Fusion Tokamak Simulation

Runaway electrons (RE) generated during magnetic disruptions present a major threat to the safe operation of plasma nuclear fusion reactors. A critical aspect of understanding RE dynamics is to calculate the runaway probability, i.e., the probability that an electron in the phase space will runaway on, or before, a prescribed time. Such probability can be obtained by solving the adjoint equation of the underlying Fokker-Planck equation that controls the electron dynamics. In this effort, we present a sparse-grid probabilistic scheme for computing the runaway probability. The key ingredient of our approach is to represent the solution of the adjoint equation as a conditional expectation, such that discretizing the differential operator reduces to the approximation of a set of integrals. Adaptive sparse grid interpolation is utilized to approximate the map from the phase space to the runaway probability. The main novelties of this effort are the integration of the sparse-grid method into the probabilistic numerical scheme for computing escape probability, and the application of the proposed method in computing RE probabilities. Two numerical examples are given to illustrate that the proposed method can achieve O(Δt) convergence, and that the local anisotropic adaptive refinement strategy (M. Stoyanov, Adaptive sparse grid construction in a context of local anisotropy and multiple hierarchical parents. In: Sparse Grids and Applications-Miami 2016, Springer, Berlin, 2018, pp. 175–199) can effectively handle the sharp transition layer between the runaway and non-runaway regions.

Yang, Minglei↗