Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Infrared extinction in the inner Milky Way through red clump giants

While the shape of the extinction curve in the infrared is considered to be set and the extinction ratios between infrared bands are usually taken to be approximately constant, a number of recent studies point to either a spatially variable behavior of the exponent of the power law or a different extinction law altogether. In this paper, we propose a method to analyze the overall behavior of the interstellar extinction by means of the red-clump population, and we apply it to those areas of the Milky Way where the presence of interstellar matter is heavily felt: areas located in 5° < l < 30° and b = 0°. We show that the extinction ratios traditionally used for the near infrared could be inappropriate for the inner Galaxy and we analyze the behavior of the extinction law from 1 μm to 8 μm.

79 ASTRONOMY AND ASTROPHYSICS↗

Large-Signal Impedance Modeling of Three-Phase Voltage Source Converters

Resonance problems have become a major hurdle in the large-scale grid integration of renewable energy. It is important to be able to predict the amplitude of resonance-induced distortions for the protection and control design of power electronic converters. We recently presented an impedance-based approach for the prediction of resonance amplitude. It was shown that the impedance response of a converter starts changing with the amplitude of resonance; this blocks the amplitude growth beyond a certain point where the converter forms a limit cycle mode of sustained oscillations. The large-signal impedance of a converter captures the change in its impedance response with the resonance amplitude, and it can be used to predict the resonance amplitude under different operation conditions. This paper presents large-signal sequence impedance modeling for three-phase voltage source converters (VSC) with dq-current control and PLL. Modeling challenges encountered in the absence of the small-signal approximation are addressed by a) leveraging the dominating influence of hard nonlinearities such as pulse-width modulation saturation and limiters over soft nonlinearities in shaping the converter large-signal behavior and b) modeling the large-signal gain of hard nonlinearities using appropriate describing functions. Developed large-signal impedance models are validated using numerical simulations. Measurements of the large-signal impedance responses of a commercial 1-MW VSC-based inverter are also presented to experimentally demonstrate the effects of the injected perturbation amplitude on impedance response as predicted by the developed model.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Use of Transition Models to Design High Performance TESs for the LCLS-II Soft X-Ray Spectrometer

We are designing an array of transition-edge sensor (TES) microcalorimeters for a soft X-ray spectrometer at the Linac Coherent Light Source at SLAC National Accelerator Laboratory to coincide with upgrades to the free electron laser facility. The complete spectrometer will have 1000 TES pixels with energy resolution of 0.5 eV full-width at half-maximum (FWHM) for incident energies below 1 keV while maintaining pulse decay-time constants shorter than 100 μs. In the past, TES pixels have often been designed for a particular scientific application via a combination of simple scaling relations and trial-and-error experimentation with device geometry. We have improved upon this process by using our understanding of transition physics to guide TES design. Using the two-fluid approximation of the phase-slip line model for TES resistance, we observe how the geometry and critical temperature of a TES will affect the shape of the transition. We have used these techniques to design sensors with a critical temperature of 55 mK. The best sensors achieve an energy resolution of 0.75 eV FWHM at 1.25 keV. Building upon this result, we show how the next generation of sensors can be designed to reach our goal of 0.5 eV resolution.

47 OTHER INSTRUMENTATION↗

SU-E-T-612: Photonuclear Activation of Prosthetic Hips in Radiotherapy

Purpose: To measure the neutron induced activation of a prosthetic hip when exposed to an 18 MV radiotherapy linac beam to assess the potential dose to patients. Methods: A prosthetic hip (Thackray, UK) was placed in a water phantom and irradiated (both in-field and out-of-field) with an 18 MV linac beam. Gamma spectroscopy was used to identify the radioisotopes produced. Following the in-field irradiation where the induced activity is higher, high sensitivity lithium fluoride Thermoluminescence Dosimeters (TLD-100H) (Harshaw, USA) were placed on the surface to measure the dose which would be deposited to nearby tissue resulting from the induced radioactivity. Results: The radioisotopes produced in the hip prosthesis have been identified as {sup 5{sup 2}}V, {sup 5{sup 3}}Fe, and {sup 56}Mn which have half-lives of 3.74, 8.51 and minutes respectively. The 378 and 511 keV characteristic peaks of {sup 5{sup 3}}Fe do not appear in the spectra collected from hips irradiated in the out-of-field region. This isotope is produced by photonuclear interactions within the hip itself. {sup 52}V and {sup 56}Mn appear in spectra collected from hips irradiated either within the photon beam or in the nearby out-of-field region, implying that they are produced by incident neutron radiation produced in components of the linear accelerator.The integrated dose which would be deposited in the tissue immediately surrounding the hip after four hours (1.5 half-lives of the longest lived product) was measured as approximately 100 µGy, following a 10,000 MU irradiation of the prosthesis. A highly accurate measurement of the dose is challenging because of the irregular shape of the prosthesis. Conclusion: The cumulative dose measured at the surface of the hip is 0.0001% of the in-field dose, and is therefore negligible compared with the doses the patient receives as a consequence of their treatment.

61 RADIATION PROTECTION AND DOSIMETRY↗

Nonlinear waves on the free surface of a dielectric liquid in an oblique electric field

The nonlinear dynamics of the free surface of an ideal dielectric liquid that is exposed to an external oblique electric field has been studied theoretically. In the framework of the Hamiltonian formalism, a system of nonlinear integro-differential equations has been derived that describes the dynamics of nonlinear waves in the small-angle approximation. It is established that for a liquid with high dielectric permittivity, these equations have a solution in the form of plane waves of arbitrary shape that propagate without distortion in the direction of the horizontal component of the external field.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrodynamic Calculation of Effective Electromagnetic Parameters of a Dielectric Medium with Metallic Nanoparticles of a Given Size

The frequency dependence of the effective complex permittivity and effective complex permeability of a heterostructure based on a dielectric medium containing metallic nanoparticles of spherical shape is calculated by an original method. In contrast to the Bruggeman [21] and the Maxwell Garnett [17] approaches, which use the quasi-static approximation in calculations, a nonuniform distribution of electromagnetic fields inside metallic particles is calculated, which allows the analysis of the electromagnetic parameters of the heterostructure not only as a function of frequency but also as a function of the nanoparticle size. It is shown that the plasmon resonant frequency decreases with increasing both the size and the concentration of particles in the heterostructure. It is also shown that a dielectric medium containing nonmagnetic metallic nanoparticles exhibits diamagnetic properties. In this case, the position of the maximum on the frequency dependence of the imaginary part of the magnetic susceptibility coincides with the relaxation frequency of charge carriers. The calculated spectra of the real and imaginary components of the permittivity of the heterostructure with a size of metallic particles less than 10 nm are in good agreement with Bruggeman calculations; however, the agreement with Maxwell Garnett calculations is observed only at nanoparticle concentrations lower than 10{sup –6}.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Cycling-Induced Changes in the Entropy Profiles of Lithium Cobalt Oxide Electrodes

Entropy profiles of lithium cobalt oxide (LiCoO2) electrodes were measured at various stages in the cycle life to examine performance degradation and cycling-induced changes, or lack thereof, in thermodynamics. LiCoO 2 electrodes were cycled at C/2 rate in half-cells (vs. lithium anodes) up to 20 cycles or C/5 rate in full cells (vs. MCMB anodes) up to 500 cycles. The electrodes were then subjected to entropy measurements (∂E/∂T, where E is open-circuit potential and T is temperature) in half-cells at regular intervals over the approximate range 0.5 ≤ x ≤ 1 in LixCoO 2 . Despite significant losses in capacity upon cycling, neither cycling rate resulted in any change to the overall shape of the entropy profile relative to an uncycled electrode, indicating retention of the basic LiCoO 2 structure, lithium insertion mechanism, and thermodynamics. This confirms that cycling-induced performance degradation in LiCoO 2 electrodes is primarily caused by kinetic barriers that increase with cycling. In the case of electrodes cycled at C/5, there was a subtle, quantitative, and gradual change in the entropy profile in the narrow potential range of the hexagonal-to-monoclinic phase transition. The observed change is indicative of a decrease in the intralayer lithium ordering that occurs at these potentials, and it demonstrates that a cyclinginduced structural disorder accompanies the kinetic degradation mechanisms.

25 ENERGY STORAGE↗

Revolutionizing Turbine Cooling with Micro-Architectures Enabled by Direct Metal Laser Sintering

The objective of this research effort was to explore innovative cooling architectures enabled by additive manufacturing techniques for improved turbine cooling performance. The ability to create complex internal geometries was leveraged to better distribute coolant as well as to integrate inherently unstable flow devices to enhance internal and external heat transfer. This was accomplished with a multi-faceted approach including analytical, experimental, and computational components. This final report documents progress during the total 4.25 year effort that was extended (at no additional cost) from the original 3-year cooperative agreement. Prior to starting the project, significant effort was invested in investigating innovative cooling designs from the open literature. When the project started, we quickly down-selected to 4 configurations: impingement jet fluidic oscillators (for internal leading edge cooling), reverse film cooling (for pressure surface), sweeping film cooling jets (for suction surface), and trailing edge slot cooling with microchannels. During the 2nd year, the reverse film cooling design was shown to be sub-optimal and work on that topic was halted. The three remaining technologies were integrated into a large scale nozzle guide vane and installed into a low-speed linear cascade facility for further interrogation. Initial results showed the sweeping film cooling jets (on the suction surface) to be the most promising technology compared to a baseline diffusion shaped film hole (777 design). The benefit was particularly evident at high blowing ratios (>1.5) when the 777 coolant film separated from the downstream surface. Benefits were also evident at elevated freestream turbulence levels. The leading edge cooling with unsteady jets was less effective in terms of peak or average cooling – however it was superior to round hole impingement cooling in terms of spatial uniformity. Finally, the trailing edge cooling design with micro-channels was scrapped in favor of a pinned arrangement with centerbody. During the 3rd year, the same three technologies were integrated into a transonic linear cascade for an assessment of compressibility effects. Again, the sweeping film cooling jets proved superior at high blowing ratios while the unsteady leading edge impingement and trailing edge pin-fins with centerbody designs yielded mixed results. Finally, during the 4th and final year, these 3 technologies were integrated into a direct metal laser sintered (DMLS) nozzle guide vane for testing in a high temperature, transonic annular vane cascade. The facility matches the flow temperature, Mach number, and coolant pressure ratios of an actual gas turbine. Before doing this, an additional series of tests were completed to validate a redesigned trailing edge cooling architecture. This final design included a centerbody with triangular pins between the centerbody and the vane external skin. The majority of these triangular pins are fabricated with a 30% gap to the centerbody – reducing their pressure drop considerably while still providing excellent heat transfer augmentation. This additional test campaign required an additional 3-month extension request to complete testing in the high temperature NGV test facility (Turbine Reacting Flow Rig – TuRFR). Testing of the DMLS vane in TuRFR pitted the 3 innovative cooling technologies against more traditional technologies (shaped 777 film hole, round impingement jet, and full pin arrangement in the trailing edge. The sweeping film cooling jets (on the suction surface) showed approximately 15% improvement in overall effectiveness compared to the 777 film hole while the trailing edge showed up to 20% improvement. The leading edge impingement was disappointing with a substantially lower effectiveness than traditional direct impingement. In summary, the study was successful in demonstrating that DMLS-enabled cooling technologies can yield significant gains in cooling performance.

03 NATURAL GAS↗

Regression Based Approach for Robust Finite Element Analysis on Arbitrary Grids. LDRD Final Report

This report summarizes the work performed under a one-year LDRD project aiming to enable accurate and robust numerical simulation of partial differential equations for meshes that are of poor quality. Traditional finite element methods use the mesh to both discretize the geometric domain and to define the finite element shape functions. The latter creates a dependence between the quality of the mesh and the properties of the finite element basis that may adversely affect the accuracy of the discretized problem. In this project, we propose a new approach for defining finite element shape functions that breaks this dependence and separates mesh quality from the discretization quality. At the core of the approach is a meshless definition of the shape functions, which limits the purpose of the mesh to representing the geometric domain and integrating the basis functions without having any role in their approximation quality. The resulting non-conforming space can be utilized within a standard discontinuous Galerkin framework providing a rigorous foundation for solving partial differential equations on low-quality meshes. We present a collection of numerical experiments demonstrating our approach in a wide range of settings: strongly coercive elliptic problems, linear elasticity in the compressible regime, and the stationary Stokes problem. We demonstrate convergence for all problems and stability for element pairs for problems which usually require inf-sup compatibility for conforming methods, also referring to a minor modification possible through the symmetric interior penalty Galerkin framework for stabilizing element pairs that would otherwise be traditionally unstable. Mesh robustness is particularly critical for elasticity, and we provide an example that our approach provides a greater than 5x improvement in accuracy and allows for taking an 8x larger stable timestep for a highly deformed mesh, compared to the continuous Galerkin finite element method. The report concludes with a brief summary of ongoing projects and collaborations that utilize or extend the products of this work.

97 MATHEMATICS AND COMPUTING↗

Neutrino-driven Winds in Three-dimensional Core-collapse Supernova Simulations

Abstract In this paper, we analyze the neutrino-driven winds that emerge in 12 unprecedentedly long-duration 3D core-collapse supernova simulations done using the code F ornax . The 12 models cover progenitors with zero-age main-sequence mass between 9 and 60 solar masses. In all our models, we see transonic outflows that are at least 2 times as fast as the surrounding ejecta and that originate generically from a proto−neutron star surface atmosphere that is turbulent and rotating. We find that winds are common features of 3D simulations, even if there is anisotropic early infall. We find that the basic dynamical properties of 3D winds behave qualitatively similarly to those inferred in the past using simpler 1D models, but that the shape of the emergent wind can be deformed, very aspherical, and channeled by its environment. The thermal properties of winds for less massive progenitors very approximately recapitulate the 1D stationary solutions, while for more massive progenitors they deviate significantly owing to aspherical accretion. The Y e temporal evolution in winds is stochastic, and there can be some neutron-rich phases. Though no strong r -process is seen in any model, a weak r -process can be produced, and isotopes up to 90 Zr are synthesized in some models. Finally, we find that there is at most a few percent of a solar mass in the integrated wind component, while the energy carried by the wind itself can be as much as 10%–20% of the total explosion energy.

79 ASTRONOMY AND ASTROPHYSICS↗

Modular gradient-free shaped charge

A shaped charge produces a constant velocity jet. The shaped charge is comprised of individual modules which can be assembled to produce a constant velocity jet of arbitrary length. The resulting jet speed is approximately twice the detonation velocity and independent of the liner material. The modular design also allows different liner materials to be used sequentially in the same jet.

42 ENGINEERING↗

ASYMPTOTIC OPENING ANGLES FOR COLLIDING-WIND BOW SHOCKS: THE CHARACTERISTIC-ANGLE APPROXIMATION

By considering the advection and interaction of the vector momentum flux in highly supersonic spherically diverging winds, we derive a simple analytic description of the asymptotic opening angle of a wind-collision shock cone, in the approximation that the shocked gas is contained in a cone streaming out along a single characteristic opening angle. Both highly radiative and highly adiabatic limits are treated, and their comparison is the novel result. Analytic closed-form expressions are obtained for the inferred wind momentum ratios as a function of the observed shock opening angle, allowing the conspicuous shape of the asymptotic bow shock to be used as a preliminary constraint on more detailed modeling of the colliding winds. In the process, we explore from a general perspective the limitations in applying to the global shock geometry the so-called Dyson approximation, which asserts a local balance in the perpendicular ram pressure across the shock.

79 ASTRONOMY AND ASTROPHYSICS↗

Entanglement-based perturbation theory for highly anisotropic Bose-Einstein condensates

We investigate the emergence of three-dimensional behavior in a reduced-dimension Bose-Einstein condensate trapped by a highly anisotropic potential. We handle the problem analytically by performing a perturbative Schmidt decomposition of the condensate wave function between the tightly confined (transverse) direction(s) and the loosely confined (longitudinal) direction(s). The perturbation theory is valid when the nonlinear scattering energy is small compared to the transverse energy scales. Our approach provides a straightforward way, first, to derive corrections to the transverse and longitudinal wave functions of the reduced-dimension approximation and, second, to calculate the amount of entanglement that arises between the transverse and longitudinal spatial directions. Numerical integration of the three-dimensional Gross-Pitaevskii equation for different cigar-shaped potentials and experimentally accessible parameters reveals good agreement with our analytical model even for relatively high nonlinearities. In particular, we show that even for such stronger nonlinearities the entanglement remains remarkably small, which allows the condensate to be well described by a product wave function that corresponds to a single Schmidt term.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The role of demagnetization factor in determining the ‘true’ value of the Curie temperature

The Curie temperature, T{sub c}, is the temperature above which a material loses its long-range ferromagnetic order. Considering the equation of state of a ferromagnet in the mean-field approximation it has been shown theoretically that the value of the demagnetization factor N has a significant influence on the perceived location of T{sub c} on the temperature scale. A series of precise measurements of magnetization using two differently shaped single crystals of high-purity gadolinium was carried out to prove this result experimentally and develop a procedure leading to the 'true' value of T{sub c}.

36 MATERIALS SCIENCE↗

Electronic Band Structure Information of GdN Extracted from x-ray Absorption and Emission Spectroscopy

The electronic structure of GdN films grown by pulsed laser deposition has been investigated by soft x-ray absorption (XAS) and x-ray emission spectroscopy (XES) at the N K-edge. Density functional calculations within the local spin density approximation with Hubbard-U corrections of the N p weighted bands and density of states are used to extract band information from the spectra. Gd M{sub 4,5} XAS and XES spectra are also presented. The XES-XAS separation is shown to give information on the f-band spin splitting and the XAS line shapes are shown to reflect atomic multiplet effects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An analytic approximation to the covariance between pre- and post-reconstruction galaxy two-point statistics

We present a simple analytic approximation for the covariance between pre-reconstruction galaxy power spectrum measurements and post-reconstruction two-point correlation functions. This cross-covariance is essential for joint analyses that combine full-shape clustering information with baryon acoustic oscillation (BAO) measurements, as commonly performed in modern spectroscopic surveys. Our model builds on the disconnected contribution to the covariance and accounts for the damping of correlations due to the BAO reconstruction process. We validate our analytic prescription against numerical simulations from the Dark Energy Spectroscopic Instrument (DESI), testing both idealized cubic geometries and realistic survey configurations including complex footprints and fiber assignment effects. Despite neglecting survey window functions in the analytic calculation, we find excellent agreement with simulation-based covariances and demonstrate that cosmological parameter constraints are virtually unchanged when using our approximation. Our results show that the pre-post cross-covariance is sufficiently small that even approximate treatments are adequate for cosmological inference, opening a pathway toward fully analytic covariance matrices for next-generation galaxy surveys.

baryon acoustic oscillations↗

Recent progress on spherical torus research

The spherical torus or spherical tokamak (ST) is a member of the tokamak family with its aspect ratio (A = R{sub 0}/a) reduced to A ∼ 1.5, well below the normal tokamak operating range of A ≥ 2.5. As the aspect ratio is reduced, the ideal tokamak beta β (radio of plasma to magnetic pressure) stability limit increases rapidly, approximately as β ∼ 1/A. The plasma current it can sustain for a given edge safety factor q-95 also increases rapidly. Because of the above, as well as the natural elongation κ, which makes its plasma shape appear spherical, the ST configuration can yield exceptionally high tokamak performance in a compact geometry. Due to its compactness and high performance, the ST configuration has various near term applications, including a compact fusion neutron source with low tritium consumption, in addition to its longer term goal of an attractive fusion energy power source. Since the start of the two mega-ampere class ST facilities in 2000, the National Spherical Torus Experiment in the United States and Mega Ampere Spherical Tokamak in UK, active ST research has been conducted worldwide. More than 16 ST research facilities operating during this period have achieved remarkable advances in all fusion science areas, involving fundamental fusion energy science as well as innovation. These results suggest exciting future prospects for ST research both near term and longer term. The present paper reviews the scientific progress made by the worldwide ST research community during this new mega-ampere-ST era.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the evolution of cluster scaling relations

Understanding the evolution of scaling relations between the observable properties of clusters and their total mass is key to realizing their potential as cosmological probes. In this study, we investigate whether the evolution of cluster scaling relations is affected by the spurious evolution of mass caused by the evolving reference density with respect to which halo masses are defined (pseudo-evolution). We use the relation between mass, M, and velocity dispersion, σ, as a test case, and show that the deviation from the M-σ relation of cluster-sized halos caused by pseudo-evolution is smaller than 10% for a wide range of mass definitions. The reason for this small impact is a tight relation between the velocity dispersion and mass profiles, σ(<r)=const×√(GM(<r)/r), which holds across a wide range of radii. We show that such a relation is generically expected for a variety of density profiles, as long as halos are in approximate Jeans equilibrium. Thus, as the outer 'virial' radius used to define the halo mass, R, increases due to pseudo-evolution, halos approximately preserve their M-σ relation. This result highlights the fact that tight scaling relations are the result of tight equilibrium relations between radial profiles of physical quantities. We find exceptions at very small and very large radii, where the profiles deviate from the relations they exhibit at intermediate radii. We discuss the implications of these results for other cluster scaling relations and argue that pseudo-evolution should have a small effect on most scaling relations, except for those that involve the stellar masses of galaxies. In particular, we show that the relation between stellar-mass fraction and total mass is affected by pseudo-evolution and is largely shaped by it for halo masses ≲ 10{sup 14} M {sub ☉}.

79 ASTRONOMY AND ASTROPHYSICS↗