Search NASA⌕ Search

SEARCH · Search NASA

Results for “solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Experimental Investigation of Microstructure and Phase Transitions in Ag-Cu-Zn Brazing Alloys

Microstructure and phase transitions of selected brazing alloys from the Ag-Cu-Zn ternary system were investigated. Four ternary alloys with silver content in the compositional range from 25 to 60 wt.% were studied using x-ray diffraction (XRD) and scanning electron microscopy coupled with the energy-dispersive spectroscopy (SEM–EDS). Phase transitions of the investigated alloys were measured using differential scanning calorimetry (DSC). Experimentally obtained results were compared with the results of a thermodynamic calculation of the phase equilibria according to the CALPHAD method. The experiments confirmed the optimized thermodynamic parameters for the calculations from the thermodynamic assessment in literature. Phase compositions, liquidus and solidus temperatures were confirmed by the EDS and DTA methods. Additionally, the calculated solidification paths and predicted phase transformations were in agreement with the SEM images.

36 MATERIALS SCIENCE↗

Effect of Al on Grain Refinement and Mechanical Properties of Mg-3Nd Casting Alloy

The effect of Al on the grain refinement and mechanical properties of as-cast Mg-3Nd alloy was investigated systematically by a series of microstructural analysis, solidification analysis and tensile tests. The results show that Al has an obvious refining effect on the as-cast Mg-3Nd alloy. With increasing Al content, the grain size of the as-cast Mg-3Nd alloy decreases firstly, then increases slightly after the Al content reaching 3 wt.%, and the minimum grain size of the Mg-3Nd alloy is 48 ± 4.0 μm. The refining mechanism can be attributed to the formation of Al{sub 2}Nd particles, which play an important role in the heterogeneous nucleation. The strength and elongation of the Mg-3Nd alloy refined by Al also increase with increasing Al content and slightly decrease when the Al content is more than 3 wt.%, and the strengthening mechanism is attributed to the grain refinement as well as dispersed intermetallic particles. Furthermore, the microstructural thermal stability of the Mg-3Nd-3Al alloy is higher than that of the Mg-3Nd-0.5Zr alloy. Overall, the Mg-3Nd alloy with Al addition is a novel alloy with wide and potential application prospects.

36 MATERIALS SCIENCE↗

Characterization of the Interface of an Alloy 625 Overlay on Steels Using Nanoindentation

Industry standards require postweld heat treatment (PWHT) to reduce the heat-affected zone hardness of steels such as F22 (2.25Cr-1Mo) and AISI 8630 overlaid (clad) with Alloy 625 weld metal. PWHT results in carbon diffusion and accumulation at the interface between the steel and overlay. The accumulation of carbon in a planar solidification growth zone adjacent to the fusion boundary results in high hardness and the potential for hydrogen-assisted cracking. The planar growth zone (PGZ) is so narrow that normal Vickers hardness testing cannot fully reveal the hardness distribution in this zone. This study focused on the application of nanoindentation to characterize the hardness in the narrow microstructural regions adjacent to the fusion boundary. The development of nanohardness maps revealed that the PGZ is not necessarily the region that exhibits peak hardness after PWHT. The highest hardness values were associated with clusters of M{sub 7}C{sub 3} carbides in specific subregions in the PGZ and also in the partially-mixed zone adjacent to the fusion boundary or in steel “swirl” structures. It was also confirmed in this study that nanohardness has a linear correlation with Vickers hardness values. The results presented here provide new insight into the role of carbon diffusion during PWHT and its effect on interface embrittlement associated with Alloy 625 overlays on steel.

36 MATERIALS SCIENCE↗

Formation and Toughening Mechanisms of Dispersions in Interfacial Intermetallics of Dissimilar Laser Al/Steel Joints

The key to improve the strength of Al/steel dissimilar joint is to toughen the hard and brittle interfacial intermetallics. Introducing soft and tough dispersions into the interfacial intermetallics would be a promising method. In the present study, Zn-Al alloy (Zn-22Al) was used as the filler metal to generate dispersions in the interfacial intermetallics matrix of dissimilar laser Al/steel joint. The results have shown that soft and tough dispersions, i.e., FeZn{sub 10,} Al-rich amorphous phase, and Zn solid solution, were successfully introduced into the hard and brittle Fe{sub 2}Al{sub 5−x}Zn{sub x} matrix. The formation of these dispersions was resulted from diffusion of elements Fe and Al and infiltration of liquid Zn along the grain boundaries of Fe{sub 2}Al{sub 5−x}Zn{sub x} matrix and the subsequent chemical reaction and solidification. With this kind of interfacial microstructure, the joint exhibited a stable peak fracture load of 1200 N even though the interfacial layer thickness increased from 20 to 45 μm. This was because the interfacial layer was toughened by the soft and tough dispersions. Using this example, introduction of soft and tough dispersions into hard and brittle intermetallics matrix to toughen interfacial layer and then strengthening of dissimilar joints will be highlighted.

36 MATERIALS SCIENCE↗

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Selective laser melting (SLM) process is characterized by large temperature gradients resulting in high levels of residual stress within the additively manufactured metallic structure. SLM-processed Ti6Al4V yields a martensitic microstructure due to the rapid solidification and results in a ductility generally lower than a hot working equivalent. Post-process heat treatments can be applied to SLM components to remove in-built residual stress and improve ductility. Residual stress buildup and the mechanical properties of SLM parts can be controlled by varying the SLM process parameters. This investigation studies the effect of layer thickness on residual stress and mechanical properties of SLM Ti6Al4V parts. This is the first-of-its kind study on the effect of varying power and exposure in conjunction with keeping the energy density constant on residual stress and mechanical properties of SLM Ti6Al4V components. It was found that decreasing power and increasing exposure for the same energy density lowered the residual stress and improved the % elongation of SLM Ti6Al4V parts. Increasing layer thickness resulted in lowering the residual stress at the detriment of mechanical properties. The study is based on detailed experimental analysis along with finite element simulation of the process using ABAQUS to understand the underlying physics of the process.

36 MATERIALS SCIENCE↗

The Influence of Galvanizing Parameters on the Structural Development of Zn-Al-Based Coatings

The evolution of some layers’ characteristics, deposited by galvanization, was monitored according to the technological parameters of the process. Two types of alloys from the Zn-Al and Zn-Al-Ti-B systems were used for deposition. The structure of the deposited layers was analyzed by optical and electron microscopy. The chemical composition, phases and compounds in the structures were identified. The mechanical properties of the structural constituents of the layers were determined by nanoindentation. These techniques highlighted the typical non-uniformities in terms of composition and properties in the layers, mainly due to the diffusion and distribution of iron from the steel substrate in the deposited layers. The evaluation of iron diffusion in the deposited layer was done by differential thermal analysis. The values of the critical temperatures (melting temperature, eutectic temperature and solidification temperature) were correlated with the parameters used during deposition. It was observed that the structure of the coatings is layered, with a specific order from the steel substrate to the edge. In these layers, the constituents are mixtures of soft solid solutions of Al in Zn (η and β) and hard intermetallic compounds. Moreover, increasing the immersion time in the galvanizing bath and the bath temperature leads to an increase in iron diffusion in the coating layer, which contributes to lower coating thickness, thus reducing its durability in operation.

36 MATERIALS SCIENCE↗

The Application of Centrifugal Atomization Method for Preparation of Rapidly Solidified Nd-Fe-B Flakes Used for Production of Permanent Magnets

Nd-Fe-B-type permanent magnets are used in applications that require a high-energy product/volume ratio in order to reduce weight. Automotive industry, hard drives, or wind turbines are just examples of an application where their use can be found. Conventional casting techniques reveal the formation of a high quantity of α-Fe and large Nd-rich regions. On the other hand, new techniques, like strip casting, melt-spinning and centrifugal atomization, produce homogeneous and fine-scaled microstructures. This paper discusses the application of rapid solidification by means of the centrifugal atomization method for preparation of Nd-Fe-B flakes. The effect of alloy composition and various process parameters of centrifugal atomization on the microstructure of rapidly solidified Nd-Fe-B alloy were investigated. The microstructures and the phase composition were examined by metallographic techniques, namely optical and scanning electron microscopy. Additionally, the influence of the processing parameters on the microstructures of as-cast flakes and subsequent magnetic properties of the prepared magnets will be discussed.

36 MATERIALS SCIENCE↗

Novel Fabrication of a TiB{sub 2} Grain Refiner and its Effect on Reducing Hot Tearing in AZ91D Magnesium Alloy

Despite the increased use of magnesium (Mg) alloys in diverse engineering applications in recent years, further incorporation of complex Mg alloy castings remains challenging due to the alloy’s relatively high susceptibility to hot tearing. A significant reduction in hot tearing via grain refinement was achieved in aluminum and ferrous alloys; however, an effective, long-lasting and inexpensive grain refiner for aluminum-containing Mg alloys remains elusive. In this work, a TiB{sub 2} grain refiner was fabricated via a novel spark plasma sintering (SPS) powder metallurgy process. Then, its effectiveness in grain refining an AZ91D magnesium alloy was compared to that of a commercially available TiB{sub 2} grain refiner produced by hot extrusion. Due to the homogeneous distribution of the TiAl{sub 3} and TiB{sub 2} particles in the grain refiner, as well as their effect on the alloy’s microstructure evolution and solidification behavior, the SPS-TiB{sub 2} grain refiner was observed to achieve a significant reduction in the grain size and hot tearing of the Al-containing AZ91D magnesium alloy.

36 MATERIALS SCIENCE↗

Microstructures and Mechanical Properties of Resistance Spot-Welded Steel/Aluminum Alloy Joints with Process Tapes

The microstructure and mechanical property of resistance spot-welded joints of steel and aluminum were studied by using process tapes. The steel/aluminum joint consists mainly of aluminum nugget and interface zone. The liquid nugget solidification has an epitaxial growth characteristic, and the interface zone displays a double-layer structure, Fe{sub 2}Al{sub 5} layer at steel side and Fe{sub 4}Al{sub 13} layer at aluminum nugget side. Compared with joints without process tape, the joint nugget diameter and tensile shear load increased by 35.45 and 10.98%, respectively, and its indentation ratio decreased by 56.25% due to the process tapes increasing heat input, producing larger nugget diameter and continuous interface layer, and protecting against deep indentation. The joining area of intermetallic layer and aluminum nugget is weak link in the joint. It is favorable to use the process tapes for improving welding quality, raising joint strength, and energy saving.

36 MATERIALS SCIENCE↗

Development of Stretch Flangeable Grade Steels by Inclusion Engineering Approach

The demand for good stretch flangeability in high-strength automotive steels has necessitated due attention on steel cleanliness and processes. The presence of elongated MnS stringers and centerline segregation of nonmetallic inclusions adversely affects the transverse mechanical property. In the present investigation, stretch flangeability of industrially produced steel, with and without Ca treatment, has been compared with Ti-added steel, produced at 40 kg scale without Ca treatment. The study brings out the influence of centerline segregation and modification of nonmetallic inclusions on HER performance. The microstructural analysis of industrial steel revealed that the method of hole formation (punching/drilling) determines crack initiation mechanism. The inclusions, along with the second phase present in the centerline, drive the crack propagation. An addition of Ti in liquid steel promotes formation of Al-Ti-O-based oxide, prior to MnS precipitation, during solidification and acts as nucleation site for MnS inclusion. This obviates the elongated stringer-type MnS inclusions. The centerline segregation-free Ti-modified steel, prepared at the laboratory scale, showed consistent HER property compared with industrial steel. It is also concluded that calcium treatment can be circumvented by modifying the sulfide stringer with the addition of Ti in the steel for further improvement in HER property.

36 MATERIALS SCIENCE↗

The Addition of Boron to Melt-Spun Fe-6.5%Si Ribbons

Fe-6.5%Si has higher electrical resistivity, lower magnetocrystalline anisotropy, and lower magnetostriction than traditional Fe-3.2%Si silicon steel. The reduced iron losses of Fe-6.5%Si render it a highly favorable candidate for high-speed motors and transformers. However, large-scale production of wide Fe-6.5%Si tape by rapid solidification can be challenging mainly because of its high melting point. In this work, boron is alloyed to Fe-6.5%Si to reduce its melting temperature and interfacial energy to improve the alloy’s processability. Boron additions from 0.01 wt.% to 2.24 wt.% into Fe-6.5%Si and its effect on ribbon thickness, grain size, magnetic, and mechanical properties were studied. Further, minor boron alloying significantly changed the melt pool stability and wetting on the quench wheel and in turn increased the quench rate with minimum impact on the magnetic saturation and ductility. Boron addition of < 0.06 wt.% was also found beneficial to the magnetic property of the alloy by lowering both its hysteresis and eddy current losses.

36 MATERIALS SCIENCE↗

Similarity solution for a two-phase one-dimensional Stefan problem with a convective boundary condition and a mushy zone model

A two-phase solidification process for a one-dimensional semi-infinite material is considered. It is assumed that it is ensued from a constant bulk temperature present in the vicinity of the fixed boundary, which it is modelled through a convective condition (Robin condition). The interface between the two phases is idealized as a mushy region and it is represented following the model of Solomon, Wilson, and Alexiades. An exact similarity solution is obtained when a restriction on data is verified, and it is analysed the relation between the problem considered here and the problem with a temperature condition at the fixed boundary. Moreover, it is proved that the solution to the problem with the convective boundary condition converges to the solution to a problem with a temperature condition when the heat transfer coefficient at the fixed boundary goes to infinity, and it is given an estimation of the difference between these two solutions. Results in this article complete and improve the ones obtained in Tarzia (Comput Appl Math 9:201–211, 1990).

97 MATHEMATICS AND COMPUTING↗

Methodology for Thermodynamic Analysis Coupled with Computational Fluid Dynamics Modeling for Casting a Novel Aluminum–Cerium Alloy

In this paper, we present the results of computational fluid dynamics (CFD) analysis to assess castability, porosity, molten metal fluidity and other technological properties of a new Al-Ce alloy. A thermodynamic analysis of a new Al-Ce alloy is done to obtain the physical properties as a function of temperature across both solid and liquid phases. These properties are then used to build the CFD of model the full casting process from initial pouring through to final solidification of the part, here an example of a heavy duty mor mount is used. While several excellent commercial CFD codes exists this process shows that CFD can be used to assess the capability of the alloy to properly fill the mold, as well as give predictions where scattered porosity or large-scale defects may occur in the casting. Further, unlike the commercially available software (e.g., ProCAST, SOLIDCast , MAGMASOFT®) the complex 3D-analysis of the stress / strain fields in cast parts is not performed at this time. However, the availability of free software for assessing the required thermodynamic / thermo-physical properties of new alloys (OpenCALPHAD) and CFD codes such as OpenFOAM® makes the developed option attractive and economical, especially for the analysis of new Al-Ce alloys, for which the available data does not exist.

36 MATERIALS SCIENCE↗

Formation, stability, and crystal structure of &sigma; phase in Mo-Re-Si alloys

The formation, stability and crystal structure of the {sigma} phase in Mo-Re-Si alloys were investigated. Guided by thermodynamic calculations, six critically selected alloys were arc melted and annealed at 1600 C for 150 h. Their as-cast and annealed microstructures, including phase fractions and distributions, the compositions of the constituent phases and the crystal structure of the {sigma} phase were analyzed by thermodynamic modeling coupled with experimental characterization by scanning electron microscopy, electron probe microanalysis, X-ray diffraction and transmission electron microscopy. Two key findings resulted from this work. One is the large homogeneity range of the {sigma} phase region, extending from binary Mo-Re to ternary Mo-Re-Si. The other is the formation of a {sigma} phase in Mo-rich alloys either through the peritectic reaction of liquid + Mo{sub ss} {yields} {sigma} or primary solidification. These findings are important in understanding the effects of Re on the microstructure and providing guidance on the design of Mo-Re-Si alloys.

36 MATERIALS SCIENCE↗

Characterization of dislocation structures and deformation mechanisms in as-grown and deformed directionally solidified NiAl–Mo composites

In this paper, directionally solidified (DS) NiAl–Mo eutectic composites were strained to plastic strain values ranging from 0% to 12% to investigate the origin of the previously observed stochastic versus deterministic mechanical behaviors of Mo-alloy micropillars in terms of the development of dislocation structures at different pre-strain levels. The DS composites consist of long, [1 0 0] single-crystal Mo-alloy fibers with approximately square cross-sections embedded in a [1 0 0] single-crystal NiAl matrix. Scanning transmission electron microscopy (STEM) and computational stress state analysis were conducted for the current study. STEM of the as-grown samples (without pre-straining) reveal no dislocations in the investigated Mo-alloy fibers. In the NiAl matrix, on the other hand, a(1 0 0)-type dislocations exist in two orthogonal orientations: along the [1 0 0] Mo fiber axis, and wrapped around the fiber axis. They presumably form to accommodate the different thermal contractions of the two phases during cool down after eutectic solidification. At intermediate pre-strain levels (4–8%), a/2(1 1 1)-type dislocations are present in the Mo-alloy fibers and the pre-existing dislocations in the NiAl matrix seem to be swept toward the interphase boundary. Some of the dislocations in the Mo-alloy fibers appear to be transformed from a(1 0 0)-type dislocations present in the NiAl matrix. Subsequently, the transformed dislocations in the fibers propagate through the NiAl matrix as a(1 1 1) dislocations and aid in initiating additional slip bands in adjacent fibers. Thereafter, co-deformation presumably occurs by (1 1 1) slip in both phases. With a further increase in the pre-strain level (>10%), multiple a/2(1 1 1)-type dislocations are observed in many locations in the Mo-alloy fibers. Interactions between these systems upon subsequent deformation could lead to stable junctions and persistent dislocation sources. Finally, the transition from stochastic to deterministic, bulk-like behavior in sub-micron Mo-alloy pillars may therefore be related to an increasing number of multiple a(1 1 1) dislocation systems within the Mo fibers with increasing pre-strain, considering that the bulk-like behavior is governed by the forest hardening of these junctions.

36 MATERIALS SCIENCE↗

Structure-processing correlations and mechanical properties in freeze-cast Ti-6Al-4V with highly aligned porosity and a lightweight Ti-6Al-4V-PMMA composite with excellent energy absorption capability

In contrast to freeze-cast ceramics and polymers, few freeze-cast metals have been described, to date. This systematic study on structure-processing correlations in freeze-cast Ti-6Al-4V scaffolds reports how processing parameters determine the architecture formed during the directional solidification of water-based metal slurries and after sintering. Additionally, sedimentation in the slurry during freezing and volume shrinkage during burnout and sintering were found to significantly affect both structure and properties of the scaffolds. In using two freezing rates, 1 and 10 °C min -1 , two water-based polymer solutions as binders (chitosan and carboxymethyl cellulose) and two different metal volume fractions in the slurry, 20 and 30 vol%, Ti-6Al-4V scaffolds could be prepared with pore length, width, and porosity ranging from 41 to 523 μm, 14.5–76.5 μm, and 65 to 34%, respectively. Their compressive strength, stiffness, and toughness (work to 20% strain) fall in the range of 83–412 MPa, 7–29 GPa, and 14–122 MJ m -3 , respectively. In order to improve the properties a select composition was infiltrated with poly(methyl methacrylate). This increased the average yield strength by a factor of 2.3 from 83 to 193 MPa and the average toughness (work to 50% strain) by a factor of 2.7 from 28.1 to 76.8 MJ m -3 .

36 MATERIALS SCIENCE↗

Assessment of critical flaw sizes and crack driving forces during additive manufacturing of metallic materials

Additive manufacturing (AM) of complex engineering components is often plagued by a high susceptibility to cracking, particularly in high-strength metallic materials. While alloy design efforts have made progress in mitigating solidification defects, there remains a need for mechanistic guidelines to predict susceptibility to solid-state cracking. To address this gap, driving forces for the growth of melt pool cracks are calculated across a wide range of alloys using an efficient computational framework. Calculations are coupled with rapid single track laser experiments to elucidate trends in cracking from laser melting. The analyses conducted here highlight the important role of material properties in susceptibility to cracking, notably fracture toughness and elastic modulus. An important finding is that residual stresses that are limited in magnitude to the yield stress of the material are likely insufficient to drive cracking during cooling. Furthermore, the implications of these results are discussed in the context of alloy design for AM and residual stress accumulation during AM.

36 MATERIALS SCIENCE↗